Thyristor High Voltage, Phase ontrol SR, 30 2 () FETURES High voltage (up to 1600 V) Designed and qualified according to JEDE -JESD47 TO-247 1 2 3 1 (K) (G) 3 125 max. operating junction temperature Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 vailable PRODUT SUMMRY Package TO-247 Diode variation Single SR I T(V) 20 V DRM /V RRM 1600 V V TM 1.3 V I GT 45 m T J -40 to 125 PPLITIONS Typical usage is in input rectification crowbar (soft start) and switch in motor control, UPS, welding and battery charge DESRIPTION The VS-30TPS16... high voltage series of silicon controlled rectifiers are specifically designed for medium power switching and phase control applications. The glass passivation technology used has reliable operation up to 125 junction temperature. MJOR RTINGS ND HRTERISTIS PRMETER TEST ONDITIONS VLUES UNITS I T(V) Sinusoidal waveform 20 I RMS 30 V RRM /V DRM 1600 V I TSM 300 V T 20, T J = 25 1.3 V dv/dt 500 V/μs di/dt 150 /μs T J -40 to 125 VOLTGE RTINGS PRT NUMBER V RRM /V DRM, MXIMUM REPETITIVE PEK ND OFF-STTE VOLTGE V V RSM, MXIMUM NON-REPETITIVE PEK REVERSE VOLTGE V I RRM /I DRM T 125 m 1600 1700 10 Revision: 06-Feb-14 1 Document Number: 94387 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
BSOLUTE MXIMUM RTINGS PRMETER SYMBOL TEST ONDITIONS VLUES UNITS Maximum average on-state current I T(V) T = 95, 180 conduction half sine wave 20 Maximum RMS on-state current I RMS 30 Maximum peak, one-cycle, non-repetitive surge current I TSM 10 ms sine pulse, no voltage reapplied 300 10 ms sine pulse, rated V RRM applied 250 10 ms sine pulse, rated V RRM applied 310 Maximum I 2 t for fusing I 2 t 10 ms sine pulse, no voltage reapplied 442 2 s Maximum I 2 t for fusing I 2 t t = 0.1 to 10 ms, no voltage reapplied 4420 2 s Maximum on-state voltage drop V TM 20, T J = 25 1.3 V On-state slope resistance r t 12 m T J = 125 Threshold voltage V T(TO) 1.0 V T J = 25 0.5 Maximum reverse and direct leakage current I RM /I DM V R = Rated V RRM /V DRM T J = 125 10 m Maximum holding current I H node supply = 6 V, resistive load, initial I T = 1, T J = 25 150 Maximum latching current I L node supply = 6 V, resistive load, T J = 25 200 Maximum rate of rise of off-state voltage dv/dt T J = T J maximum, linear to 80 % V DRM, R g -k = Open 500 V/µs Maximum rate of rise of turned-on current di/dt 150 /µs TRIGGERING PRMETER SYMBOL TEST ONDITIONS VLUES UNITS Maximum peak gate power P GM 8.0 Maximum average gate power P G(V) 2.0 W Maximum peak positive gate current + I GM 1.5 Maximum peak negative gate voltage - V GM 10 V node supply = 6 V, resistive load, T J = 25 45 m node supply = 6 V, resistive load, T J = - 10 60 node supply = 6 V, resistive load, T J = 125 20 V GT Maximum required D gate voltage to trigger node supply = 6 V, resistive load, T J = 25 2.0 node supply = 6 V, resistive load, T J = 125 1.0 V node supply = 6 V, resistive load, T J = - 10 2.5 Maximum D gate voltage not to trigger V GD 0.25 T J = 125, V DRM = Rated value Maximum D gate current not to trigger I GD 2.0 m SWITHING PRMETER SYMBOL TEST ONDITIONS VLUES UNITS Typical turn-on time t gt T J = 25 0.9 Typical reverse recovery time t rr 4 µs T J = 125 Typical turn-off time t q 110 Revision: 06-Feb-14 2 Document Number: 94387 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
THERML ND MEHNIL SPEIFITIONS PRMETER SYMBOL TEST ONDITIONS VLUES UNITS Maximum junction and storage temperature range T J, T Stg -40 to 125 Maximum thermal resistance, R thj 0.8 junction to case D operation Maximum thermal resistance, R thj 40 /W junction to ambient Maximum thermal resistance, case to heatsink R ths Mounting surface, smooth and greased 0.2 pproximate weight 6 g 0.21 oz. minimum 6 (5) kgf cm Mounting torque maximum 12 (10) (lbf in) Marking device ase style TO-247 (JEDE) 30TPS16 Maximum llowable ase Temperature ( ) 130 30TPS.. Se rie s R thj(d) = 0.8 / W 120 onduction ngle 110 30 60 90 100 120 180 90 0 5 10 15 20 25 Maximum verage On-state Power Loss (W) 60 50 40 30 20 10 180 120 90 60 30 RMS Limit onduction ngle 30TPS.. Series T = 125 J 0 0 5 10 15 20 25 30 verage On-state urrent () verage On-state urrent () Fig. 1 - urrent Rating haracteristics Fig. 3 - On-State Power Loss haracteristics Maximum llowable ase Temperature ( ) 130 120 110 100 90 30TPS.. Series R thj (D) = 0.8 / W 30 60 90 120 180 onduction Period D 80 0 5 10 15 20 25 30 35 Maximum verage On-state Power Loss (W) 80 60 40 RMS Limit 20 D 180 120 90 60 30 onduction Period 30TPS.. Se rie s T = 125 J 0 0 10 20 30 40 50 verage On-state urrent () verage On-state urrent () Fig. 2 - urrent Rating haracteristics Fig. 4 - On-State Power Loss haracteristics Revision: 06-Feb-14 3 Document Number: 94387 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
Peak Half Sine Wave On-state urrent () 280 t ny Rated Load ondition nd With Rated V 260 RRM pplied Following Surge. Initial T J= 125 240 @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 220 200 180 160 140 30TPS.. Se rie s 120 1 10 100 Peak Half Sine Wave On-state urrent () 300 280 260 240 220 200 180 160 140 Maximum Non Repetitive Surge urrent Versus Pulse Train Duration. ontrol Of onduction May Not Be Maintained. Initial T J= 125 No Voltage Reapplied Rated V RRM Reapplied 30TPS.. Series 120 0.01 0.1 1 Number Of Equal mplitude Half ycle urrent Pulses (N) Pulse Train Duration (s) Fig. 5 - Maximum Non-Repetitive Surge urrent Fig. 6 - Maximum Non-Repetitive Surge urrent 1000 Instantaneous On-state urrent () 100 10 T = 25 J T = 125 J 30TPS.. Se rie s 1 0 1 2 3 4 5 6 7 Instantaneous On-state Voltage (V) Fig. 7 - On-State Voltage Drop haracteristics Transient Thermal Impedance Z thj ( / W) 1 0.1 D = 0.50 D = 0.33 D = 0.25 D = 0.17 D = 0.08 Sing le Pu lse Steady State Value (D Operation) 30TPS.. Series 0.01 0.0001 0.001 0.01 0.1 1 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance Z thj haracteristics Revision: 06-Feb-14 4 Document Number: 94387 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
Instantaneous Gate Voltage (V) 100 10 1 Rectangular gate pulse a)recommended load line for rated di/ dt: 10 V, 20 ohms tr = 0.5 µs, tp >= 6 µs b)recommended load line for <= 30% rated di/dt: 10 V, 65 ohms tr = 1 µs, tp >= 6 µs VGD TJ = 125 TJ = 25 TJ = -10 (b) (a) IGD 30TPS.. Series Frequency Limited by PG(V) 0.1 0.001 0.01 0.1 1 10 100 Instantaneous Gate urrent () Fig. 9 - Gate haracteristics (1) PGM = 40 W, tp = 1 ms (2) PGM = 20 W, tp = 2 ms (3) PGM = 8 W, tp = 5 ms (4) PGM = 4 W, tp = 10 ms (4) (3) (2) (1) ORDERING INFORMTION TBLE Device code VS- 30 T P S 16 PbF 1 2 3 4 5 6 7 1 - product 2 - urrent rating (30 = 30 ) 3 - ircuit configuration: T = Thyristor 4 - Package: 5 - P = TO-247 Type of silicon: S = Standard recovery rectifier 6 - Voltage rating (16 = 1600 V) 7 - Environmental digit: PbF = Lead (Pb)-free and RoHS compliant -M3 = Halogen-free, RoHS compliant, and terminations lead (Pb)-free ORDERING INFORMTION (Example) PREFERRED P/N QUNTITY PER T/R MINIMUM ORDER QUNTITY PKGING DESRIPTION VS-30TPS16PbF 25 500 ntistatic plastic tubes VS-30TPS16-M3 25 500 ntistatic plastic tubes Dimensions Part marking information LINKS TO RELTED DOUMENTS TO-247 PbF TO-247 -M3 www.vishay.com/doc?95542 www.vishay.com/doc?95226 www.vishay.com/doc?95007 Revision: 06-Feb-14 5 Document Number: 94387 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
DIMENSIONS in millimeters and inches TO-247 Outline Dimensions B (2) R/2 Q (3) E S 2 Ø K M D B M (6) Φ P (Datum B) D2 Φ P1 2 x R (2) D D1 (4) 1 2 3 D Thermal pad 4 (5) L1 L See view B (4) E1 0.01 M D B M 2 x b2 3 x b 0.10 M M b4 2 x e 1 View - Plating (b1, b3, b5) Base metal DDE E (c) c1 (b, b2, b4) (4) Section -, D - D, E - E View B SYMBOL MILLIMETERS INHES MILLIMETERS INHES NOTES SYMBOL MIN. MX. MIN. MX. MIN. MX. MIN. MX. NOTES 4.65 5.31 0.183 0.209 D2 0.51 1.30 0.020 0.051 1 2.21 2.59 0.087 0.102 E 15.29 15.87 0.602 0.625 3 2 1.50 2.49 0.059 0.098 E1 13.72-0.540 - b 0.99 1.40 0.039 0.055 e 5.46 BS 0.215 BS b1 0.99 1.35 0.039 0.053 Ø K 2.54 0.010 b2 1.65 2.39 0.065 0.094 L 14.20 16.10 0.559 0.634 b3 1.65 2.34 0.065 0.092 L1 3.71 4.29 0.146 0.169 b4 2.59 3.43 0.102 0.135 Ø P 3.56 3.66 0.14 0.144 b5 2.59 3.38 0.102 0.133 Ø P1-6.98-0.275 c 0.38 0.89 0.015 0.035 Q 5.31 5.69 0.209 0.224 c1 0.38 0.84 0.015 0.033 R 4.52 5.49 0.178 0.216 D 19.71 20.70 0.776 0.815 3 S 5.51 BS 0.217 BS D1 13.08-0.515-4 Notes (1) Dimensioning and tolerancing per SME Y14.5M-1994 (2) ontour of slot optional (3) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outermost extremes of the plastic body (4) Thermal pad contour optional with dimensions D1 and E1 (5) Lead finish uncontrolled in L1 (6) Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154") (7) Outline conforms to JEDE outline TO-247 with exception of dimension c Revision: 20-pr-17 1 Document Number: 95223 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
TO-247-50 mils L/F Outline Dimensions DIMENSIONS in millimeters and inches B (2) R/2 Q (3) E S 2 Ø K M D B M (6) Φ P (Datum B) D2 Φ P1 2 x R (2) D D1 (4) 1 2 3 D Thermal pad 4 (5) L1 L See view B (4) E1 0.01 M D B M 2 x b2 3 x b 0.10 M M b4 2 x e 1 View - Plating (b1, b3, b5) Base metal DDE E (c) c1 (b, b2, b4) (4) Section -, D - D, E - E View B SYMBOL MILLIMETERS INHES MILLIMETERS INHES NOTES SYMBOL MIN. MX. MIN. MX. MIN. MX. MIN. MX. NOTES 4.65 5.31 0.183 0.209 D2 0.51 1.35 0.020 0.053 1 2.21 2.59 0.087 0.102 E 15.29 15.87 0.602 0.625 3 2 1.17 1.37 0.046 0.054 E1 13.46-0.53 - b 0.99 1.40 0.039 0.055 e 5.46 BS 0.215 BS b1 0.99 1.35 0.039 0.053 Ø K 0.254 0.010 b2 1.65 2.39 0.065 0.094 L 14.20 16.10 0.559 0.634 b3 1.65 2.34 0.065 0.092 L1 3.71 4.29 0.146 0.169 b4 2.59 3.43 0.102 0.135 Ø P 3.56 3.66 0.14 0.144 b5 2.59 3.38 0.102 0.133 Ø P1-7.39-0.291 c 0.38 0.89 0.015 0.035 Q 5.31 5.69 0.209 0.224 c1 0.38 0.84 0.015 0.033 R 4.52 5.49 0.178 0.216 D 19.71 20.70 0.776 0.815 3 S 5.51 BS 0.217 BS D1 13.08-0.515-4 Notes (1) Dimensioning and tolerancing per SME Y14.5M-1994 (2) ontour of slot optional (3) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outermost extremes of the plastic body (4) Thermal pad contour optional with dimensions D1 and E1 (5) Lead finish uncontrolled in L1 (6) Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154") (7) Outline conforms to JEDE outline TO-247 with exception of dimension c and Q Revision: 20-pr-17 1 Document Number: 95542 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOUMENT IS SUBJET TO HNGE WITHOUT NOTIE. THE PRODUTS DESRIBED HEREIN ND THIS DOUMENT RE SUBJET TO SPEIFI DISLIMERS, SET FORTH T www.vishay.com/doc?91000
Legal Disclaimer Notice Vishay Disclaimer LL PRODUT, PRODUT SPEIFITIONS ND DT RE SUBJET TO HNGE WITHOUT NOTIE TO IMPROVE RELIBILITY, FUNTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. ll operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. ustomers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 2017 VISHY INTERTEHNOLOGY, IN. LL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000