157 to 173 igh Feed Finishing of Cast Iron SEC- Series... 158 GFXC13000 Type... 162 GFX 16000 Type... 163 GFS 13000 Type... 164 GRF 17000 Type... 165 GRM 17000 Type... 166 GRV 16000 Type... 167 IG igh Feed Finishing of Cast Iron SEC-igh-Feed Facemills... 168 Cutting Edge Reference System... 169 RV4000 Type / 5000 Type, DPV4000 Type / 5000 Type... 170 FV4000 Type / 5000 Type... 171 igh Feed Finishing of on- Ferrous Metal/Thin Pieces APV5000 Type... 171 QC System System... 172 Applicable Cutter for QC-system... 173 Indications and Symbols mark: Standard stocked item mark: To be replaced by a new item featured on the same page mark: To be replaced by new item (Please confirm stock availability) mark: Semi-standard stock (Please confirm stock availability) mark: or planned stock (Please confirm stock availability) o mark: Made-to-order item mark: We cannot produce 157
GFX / GFS / GR / GRV Type General Features SEC-Goal Mill Series cutters were developed for high efficiency roughing and finishing of cast iron parts, such as engine cylinder blocks and transmission cases. Characteristics Special cutters for high feed machining of cast iron ighly reliable shoulder milling cutter with tangential inserts Multi-edged design (approx. 3 edges per inch) Finishing models feature an easy-to-use edge runout fine adjustment Inserts with chipbreaker for low cutting force Series Series Code GFX GFS GR GRV Application Finishing Finishing/Shoulder Milling Roughing Roughing Surface Roughness Ra3.2 Ra3.2 Ra12.5 Ra12.5 Appearance 162 to 163 164 165 to 166 167 Refer to pages 172 and 173 for details and specifications on the two piece mounting system and adapter. IG material Application igh Speed Finishing Finishing to General Cutting Interrupted Cutting Applicable Cutter Cast Iron Finishing B7000 AC260 AC280 GFX Type GFS Type material Application Light Cutting General Cutting eavy Interrupted Cutting Applicable Cutter AC100/AC100 Cast Iron Roughing AC200/AC200 AC300/AC300 GR Type GRV Type Characteristic of s Classification ardness Toughness (GPa) Main Coating Components Coating Thickness (μm) Characteristics Cast Iron Cast Iron AC260 92.6RA 2.6 AC280 91.7RA 3.0 Super ZX Coat Super ZX Coat 3 3 For finishing to general machining of cast iron and ductile cast iron. Employs new PVD coating consisting of multiple nanometre-thin layers of TiAl and AlCr, coupled with a tough, heat-resistant substrate for long and stable tool life. For heavy interrupted cutting and wet cutting of cast iron and ductile cast iron. Employs new PVD coating consisting of multiple nanometre-thin layers of TiAl and AlCr, coupled with an ultra-tough substrate for superior fracture resistance, and thermal crack resistance during wet cutting. B7000 Characteristic 13 AC100, AC200, and AC300 Characteristic 13 158
GFX / GFS / GR / GRV Type ApplicationRough Cutting Top Face Of Cylinder Block SEC-Goal Mill Current GRV16250R ø250special Roughness StandardRa 6.3μm AC100 PVD EquipmentSpecial Machine Shape Tangential Screw Locked Wedge Type o. of Teeth 30 30 v c m/min 80 80 v f (mm/min) 611 611 fz mm/t 0.20 0.20 a p mm 3.0Some Areas6.0 3.0Some Areas6.0 Coolant Remainder Wet Remainder Wet GRV Current pieces/corner 100 200 300 100 Units 300 Units Eliminates breakage for extended tool life. ApplicationFinishing Side Face Of Cylinder Block SEC-Goal Mill Competitor's Product Roughness StandardRz 12.5μm Equipmentorizontal Machining Center GFXC13100R ø100 B7000 CVD Shape Tangential Screw Locked Wedge Type o. of Teeth 4 10 v c m/min 1,200 251 v f (mm/min) 10,000 500 fz mm/t 0.65 0.063 a p mm 0.5 0.5 v f =10,000mm/min Achieves a v f value that is 20 times larger than our competitors' products. ApplicationFinishing Side Face Of Cylinder ead SEC-Goal Mill Competitor's Product Roughness StandardRz 12.5μm Equipmentorizontal Machining Center ApplicationFinishing GFXC13125R ø125 B7000 PVD Shape Tangential Screw Locked orizontal Screw Locked o. of Teeth 4 12 v c m/min 1,000 216 v f (mm/min) 6,000 376 fz mm/t 0.59 0.057 a p mm 0.5 1.0 v f =6,000mm/min Improves efficiency by 16 times and provides better surface roughness than our competitors' products. Bottom Face Of Cylinder Block SEC-Goal Mill Competitor's Product EquipmentSpecial Machine Special ø315 AC260 PVD Shape Tangential Screw Locked Wedge Type o. of Teeth 44(effective) 40 v c m/min 148 148 v f (mm/min) 720 720 fz mm/t 0.11 0.12 a p mm 0.5 0.5 GSV Competitor's Product pieces/corner 1,500 2,500 3,500 3,500 Units 2,300 Units Provides a tool life that is approximately 1.5 times longer than our competitors' products. ApplicationFinishing Bottom Face Of Cylinder Block SEC-Goal Mill Conventional Roughness StandardRa 6.3μm Equipmentorizontal Machining Center ApplicationFinishing GFXC13125R ø125 AC260 CB Shape Tangential Screw Locked Wedge Type o. of Teeth 10 4 v c m/min 250 510 v f (mm/min) 1,020 1,020 fz mm/t 0.16 0.20 a p mm 0.5 0.5 Coolant Remainder Wet Remainder Wet Carbide tool achieving similar tool life as CB tool. Reduces costs. Lathe Bed SEC-Goal Mill Competitor's Product Roughness StandardRa 6.3μm EquipmentDouble Column Machining Center GFX16125R ø125 AC260 Ceramics Shape Tangential Screw Locked o. of Teeth 16 10 v c m/min 300 785 v f (mm/min) 3,057 3,000 fz mm/t 0.25 0.15 a p mm 0.3 0.3 Equivalent v f value to ceramics achieved with carbide Reduced running costs IG ApplicationRough Cutting : Printing Press Roller SEC-Goal Mill Competitor's Product FCD450 Equipment : orizontal Machining Center GRM17080R ø80 AC200 PVD Shape Screw Locked Screw Locked o. of Teeth 8 9 v c m/min 230 151 v f (mm/min) 732.5 541 fz mm/t 0.1 0.1 a p mm 3 to 5 3 to 5 ApplicationRough Cutting : Machine Components SEC-Goal Mill Competitor's Product FC300 Equipment : Double Column Machining Center GRM17160R ø160 AC200 CVD Shape Screw Locked Wedge Type o. of Teeth 16 8 v c m/min 250 140 v f (mm/min) 1,780 549 fz mm/t 0.20 0.245 a p mm 3 5 2 3 5 2 Achieves 1.4x better machining efficiency. Achieves 3.2x better machining efficiency. 159
GFX / GFS / GR / GRV Type ousing SEC-Goal Mill Competitor's Product Roughness StandardRa 1.6μm Equipmentorizontal Machining Center GFXC13100R ø100 AC260 CVD Shape Tangential Screw Locked orizontal Screw Locked o. of Teeth 8 10 v c m/min 250 250 v f (mm/min) 960 530 fz mm/t 0.15 0.066 a p mm 0.1 0.1 Large Diesel Engine (Base Plate) SEC-Goal Mill Current -FC300 GFX16160R ø160 Size1,600mm 1,800mm AC260 CB Equipmentorizontal Machining Center Shape Tangential Screw Locked Blade Type o. of Teeth 20 10 v c m/min 300 980 v f (mm/min) 2,980 1,950 fz mm/t 0.25 0.10 a p mm 0.3 0.3 Provides higher efficiency, accuracy, and visually better compared to our competitors' products. Achieves a tool life that is over 2.5 times longer than our competitors' products. Carbide tools achieve 1.5 times the efficiency of CB and provides machined surfaces equivalent to those machined with CB on visual inspection. IG Side of Lathe Bed (11m Long) SEC-Goal Mill Competitor's Product FC300 Equipmentorizontal Machining Center ydraulic Component SEC-Goal Mill Competitor's Product FCD450 Equipmentorizontal Machining Center GFX16160R ø160 AC260 CVD Shape Tangential Screw Locked orizontal Screw Locked o. of Teeth 20 8 v c m/min 120 125 v f (mm/min) 477 400 fz mm/t 0.10 0.20 a p mm 0.3 0.3 GFX13080R ø80 AC260 PVD Shape Tangential Screw Locked orizontal Screw Locked o. of Teeth 8 6 v c m/min 218 180 v f (mm/min) 1,600 650 fz mm/t 0.23 0.15 a p mm 0.1 0.1 Coolant Wet Wet GFX Competitor's Product GFX Competitor's Product Cutting Length/Corner 20m40m 40m 10m Achieves a cutting distance 4 times longer than competitor's. pieces/corner 50100150 148 Units 100 Units Provides a tool life that is approximately 1.5 times longer than conventional. Plate SEC-Goal Mill FC300 GFS13125R AC260 Equipmentorizontal Machining Center Shape Tangential Screw Locked o. of Teeth 6 v c m/min 137 v f (mm/min) 1,000 fz mm/t 0.47 a p mm 0.015 Coolant Rear ub Carrier SEC-Goal Mill Current FCD450 GFX16100R ø100 Roughness StandardRz 25μm AC260 CVD Equipmentorizontal Machining Center Shape Tangential Screw Locked Wedge Type o. of Teeth 12 14 v c m/min 250 150 v f (mm/min) 3,150 800 fz mm/t 0.33 0.12 a p mm 0.5-1.0 0.5-1.0 Coolant Wet Wet Dry Surface roughness: Ra 1.0μm o level differences. Final grinding process eliminated. Current tools make level differences in machined surfaces. Efficiency improved. ydraulic Component SEC-Goal Mill Conventional FCD600 GFX16125RSpecial ø125 Roughness StandardRa 1.6μm AC260 PVD Equipmentorizontal Machining Center Shape Tangential Screw Locked Wedge Type o. of Teeth 6 6 v c m/min 160 150 v f (mm/min) 733 110 fz mm/t 0.30/1.20 0.05 a p mm 0.25 0.25 Coolant Wet Wet GFX Competitor's Product Life Time/Corner 200min400min. 350 min 150 min Provides a tool life that is approximately 2.3 times longer than conventional. ApplicationSimultaneous Finishing Crankcase SEC-Goal Mill Competitor's Product AI + FC250 EquipmentVertical Machining Center GFX13100R ø100 AC260 PVD Shape Tangential Screw Locked Vertical Drawing Pins o. of Teeth 12 12 v c m/min 400 314 v f (mm/min) 1,529 1,440 fz mm/t 0.10 0.12 a p mm 0.3 0.3 Coolant Wet Wet GFX Competitor's Product pieces/corner 100 200 300 250 Units 100 Units Provides a tool life that is approximately 2.5 times longer than competitors'. 160
GFX Type GFX Type Features Easy Run-out Adjustment Peripheral Roughing Edge Front Roughing Edge Set Screw For Fine Adjustment Of Cutting Edge eight Finishing Edge Economical, 8-Cornered Insert Finishing edge run-out can be adjusted by 5μm or less simply by turning set screw. Front Roughing Edge Finishing Edge Peripheral Roughing Edge Peripheral Roughing Edge Finishing Edge Peripheral Roughing Edge Arraying the same number of vertical and horizontal inserts allows 8-corner configuration. Front Roughing Edge 0.03 to 0.04mm Finishing Edge Fine Adjustment Screw Finishing Edge Adjustment on GFX Type GFX Type Finishing Edge Run-Out Adjustment Procedure (1)Attach Insert Attach insert to cutter body. When doing so, check that the cartridge adjustment set screw is completely loose. Peripheral Roughing Edge (Direct-Mounted) Adjustment Set Screw (4)Adjust Finishing Edge eight Select a finishing edge and adjust the set screw so that the edge sticks up around 0.03 to 0.04mm compared to (3). +0.03 to 0.04mm IG Front Roughing Edge (Direct-Mounted) Finishing Edge (Cartridges) (2)Check Roughing Edge Run-Out Measure face run-out of roughing edge and check the cutting edge that sticks up the most. (5)Adjust Run-Out With the finishing edge from (4) as a reference, adjust the position of the other finishing edges so that run-out is equal to or less than 5μm. Run-Out: 5μm or less * (3)Set Reference Roughing Edge Set the cutting edge height checked in (2) as "0". ighest Roughing Edge Always adjust finishing edge height before use. Using the tool with the set screw loosened may result in tool breakage. *Adjusting finishing edge run-out to 2μm or less will result in a better machined surface. 161
GFX13000 / GFXC13000 Type Rake Radial Axial 8 5 1 89to 8930 P Steel M S Stainless Steel Cast Iron on-ferrous Metal Aluminum Exotic Alloy ardened Steel igh Feed Finishing Of Cast Iron GFX GFXC IG 1 2 3 4 SFMS SFMS B SFMS B B ø13 *1 ø20 *2 4-ø18 X X X Body (GFX 13000) (R) Inch (L) SFMS ø177.8 ø101.7 B 4-ø18 4-ø22 X GFX 13080R GFX 13080L 80 67.3 60 50 25.4 9.5 6 25 8 2 8 1.4 1 13100R 13100L 100 87.3 70 50 31.75 12.7 8 32 12 3 12 1.9 2 13125R 13125L 125 112.3 80 63 38.1 15.9 10 38 16 4 16 3.3 2 13160R 13160L 160 147.3 120 63 50.8 19 11 38 20 5 20 6.4 2 13200R 13200L 200 187.3 150 63 47.625 25.4 14 35 28 7 28 7.8 3 13250R 13250L 250 237.3 200 63 47.625 25.4 14 35 36 9 36 12.6 3 13315R 13315L 315 302.3 240 80 47.625 25.4 14 35 44 11 44 20.2 4 Body (GFXC 13000 Course Pitch) Metric Inch ote: The GFXC13063 RS/LS are only available in metric sizes. GFXC 13063RS GFXC 13063LS 63 50.3 50 50 22 10.4 6 20 4 1 4 0.9 1 GFXC 13080R GFXC 13080L 80 67.3 60 50 25.4 9.5 6 25 6 1 6 1.4 1 13100R 13100L 100 87.3 70 50 31.75 12.7 8 32 8 2 8 1.9 2 13125R 13125L 125 112.3 80 63 38.1 15.9 10 38 10 2 10 3.3 2 13160R 13160L 160 147.3 120 63 50.8 19 11 38 12 3 12 6.4 2 13200R 13200L 200 187.3 150 63 47.625 25.4 14 35 16 4 16 7.8 3 13250R 13250L 250 237.3 200 63 47.625 25.4 14 35 20 5 20 12.6 3 13315R 13315L 315 302.3 240 80 47.625 25.4 14 35 24 6 24 20.2 4 *1 GFXC13063RS/LS is ø11. *2 GFXC13063RS/LS is ø18. Inserts P Steel M Stainless Steel Cast Iron on-ferrous Metal S Exotic Alloy ardened Steel 5 9.525 RE ø4.2 6 12.700 4.76 12.70 4.76 90 Coated Carbide Carbide CB igh Speed Finishing Application Finishing/Medium Cutting Roughing 9.615 Max. Diameter Diameter Boss eight ole Size Grooving Width Grooving Depth Mounting Depth Total X SFMS B Teeth AC260 AC280 AC300 10E RE ø4.2 o. of Finishing Edges Effective Teeth Weight (kg) B7000 Dimensions (mm) Corner Radius RE LGX 130508PF-W 0.8 5 130516PF-W 1.6 5 LGX 130516PT-W 1.6 6 163 159 Allowable Spindle Speeds by Size When Using CB Inserts 163 GFXC Important otes The GFXC can be used with a reduced number of attached teeth. In this case, attach the inserts only to the attachment positions indicated by the markings. Remove the screws for the attachment positions that are not used. Attach the inserts only to the attachment positions indicated by the markings. o. of Total Teeth and o. of Attached Inserts When Reducing Teeth for GFXC ardness Cutting Speed v c (m/min). Feed Rate f z (mm/t). Cast Iron 250B 200-250- 350 0.1-0.3-0.5 AC260 Cast Iron 250B 800-1000-1200 0.1-0.3-0.5 B7000 ote Diameter Total Teeth o. of Attached Inserts When Reducing Teeth Diameter Markings Total Teeth o. of Attached Inserts When Reducing Teeth GFXC 13063RS/LS 63mm 4 2 GFXC 13160R/L 160mm 12 6 13080R/L 80mm 6 2 13200R/L 200mm 16 8 13100R/L 100mm 8 4 13250R/L 250mm 20 10 13125R/L 125mm 10 4 13315R/L 315mm 24 12 * The number of attached inserts must always be either "Total Teeth" or "o. of Attached Inserts When Reducing Teeth". 162 mark: Standard stocked item (expanded item)
Rake Radial Axial 8 5 1 89to 8930 P Steel M S Stainless Steel Cast Iron on-ferrous Metal Aluminum Exotic Alloy ardened Steel SEC-Goal Mill GFX16000 Type igh Feed Finishing Of Cast Iron 1 2 3 4 SFMS SFMS B SFMS B B ø13 *1 ø20 *2 4-ø18 X X X Body (GFX 16000) Inch X (R) (L) Max. Diameter Diameter Boss eight ole Size Grooving Width Grooving Depth Mounting Depth Total o. of Finishing Effective Weight X SFMS B Teeth Edges Teeth (kg) GFX 16080R GFX 16080L 80 64.1 60 50 25.4 9.5 6 25 8 2 8 1.4 1 16100R 16100L 100 84.1 70 50 31.75 12.7 8 32 12 3 12 1.9 2 16125R 16125L 125 109.1 80 63 38.1 15.9 10 38 16 4 16 3.3 2 16160R 16160L 160 144.1 120 63 50.8 19 11 38 20 5 20 6.4 2 16200R 16200L 200 184.1 150 63 47.625 25.4 14 35 28 7 28 7.8 3 16250R 16250L 250 234.1 200 63 47.625 25.4 14 35 36 9 36 12.6 3 16315R 16315L 315 299.1 240 80 47.625 25.4 14 35 44 11 44 20.2 4 Inserts P Steel M Stainless Steel Cast Iron on-ferrous Metal S Exotic Alloy ardened Steel 5 6 R1.6 ø4.2 9.525 15.875 4.76 15.875 4.76 90 Coated CarbideCarbide CB igh Speed Finishing Application Finishing/Medium Cutting Roughing 9.615 AC260 AC280 AC300 10E SFMS ø177.8 ø101.7 B 4-ø18 4-ø22 R1.6 ø4.2 B7000 LGX 160516PF-W 5 160516PT-W 6 ardness Cutting Speed c m/min Feed Rate z mm/t Cast Iron 250B 200-250- 350 0.1-0.3-0.5 AC260 Cast Iron 250B 800-1000-1200 0.1-0.3-0.5 B7000 ote Allowable Spindle Speeds by Size When Using CB Inserts Cutter Diameter (mm) Allowable Spindle Speed (min -1 ) n max. Cutter Diameter (mm) Allowable Spindle Speed (min -1 ) n max. ø63 6,000 ø160 2,300 ø80 4,700 ø200 1,900 ø100 3,800 ø250 1,500 ø125 3,000 ø315 1,200 IG Cartridge (For 13000) Cartridge (For 16000) Fine adjustment screw Wrench Insert Screw Wrench CapScrew CapScrew (For Adjustment) (For GFX4R/L) (For GFV5R/L) Wrench (For Cartridges) Anti-seizure Cream m GFX4R/L GFV5R/L BTD05F09 TTX15W BFTX03588 LT15 BX0414 BX0418 T030 SUMI-P 3.0 159 *Finishing cartridges do not come assembled with inserts. m Recommended Tightening Torque m 163
GFS13000 Type Rake Radial Axial 11 3 10 90 P Steel M S Stainless Steel Cast Iron on-ferrous Metal Aluminum Exotic Alloy ardened Steel igh Feed Finishing/Shoulder Milling Of Cast Iron 1 2 SFMS B X ø13 ø20 SFMS B X Body Inch (R) (L) Max. Diameter Diameter Boss eight ole Size Grooving Width Grooving Depth Mounting Depth Total o. of Finishing Effective Weight X SFMS B Teeth Edges Teeth (kg) GFS 13080R GFS 13080L 80 66.9 60 50 25.4 9.5 6 25 5 1 4 1.4 1 13100R 13100L 100 86.9 70 50 31.75 12.7 8 32 6 1 5 1.9 2 13125R 13125L 125 111.9 80 63 38.1 15.9 10 38 8 2 6 3.3 2 13160R 13160L 160 147.3 120 63 50.8 19 11 38 10 2 8 6.4 2 Inserts P Steel M Stainless Steel Cast Iron on-ferrous Metal S Exotic Alloy ardened Steel IG 9.525 12.700 RE ø4.2 Coated Carbide Carbide igh Speed/Light Application General Purpose Dimensions Roughing (mm) Corner Radius RE 4.76 AC260 AC280 AC300 10E LGX 130508PF-W 0.8 130516PF-W 1.6 90 0.2mm 0.05mm Gap On Corner Finishing Fine adjustment Cartridge* screw Wrench Insert Screw Wrench CapScrew Wrench Anti-seizure (For Adjustment) (For Cartridges) (For Cartridges) Cream 160 m GFS4R/L BTD05F09 TTX15W BFTX03588 LT15 BX0520 T040 SUMI-P 3.0 m Recommended Tightening Torque m ISO ardness Cutting Speed c m/min Feed Rate z mm/t *Finishing cartridges do not come assembled with inserts. Cast Iron 250B 200-250 -300 0.10-0.15-0.30 AC260 ote 164
Rake Radial Axial 6 Steel -6 60 P M Stainless Steel Cast Iron on-ferrous Metal Aluminum S Exotic Alloy ardened Steel SEC-Goal Mill GRF 17000 Type Roughing of Cast Iron 1 2 3 4 X SFMS B ø13 ø35 X SFMS B X SFMS B 4-ø18 X SFMS ø177.8 B 4-ø18 4-ø22 Body Inserts Inch Application Coated Carbide igh Speed/Light General Purpose Roughing AC100 AC200 AC300 (R) (L) Diameter Max. Diameter Boss eight ole Size Grooving Width Grooving Depth Mounting Depth Total Weight X SFMS B Teeth (kg) GRF 17080R GRF 17080L 80 90.5 60 50 25.4 9.5 6 25 10 1.2 1 17100R 17100L 100 110.5 70 50 31.75 12.7 8 32 14 1.8 2 17125R 17125L 125 135.5 80 63 38.1 15.9 10 38 18 2.9 2 17160R 17160L 160 170.5 100 63 50.8 19.1 11 38 22 4.5 2 17200R 17200L 200 210.5 150 63 47.625 25.4 14 35 28 7.3 3 17250R 17250L 250 260.5 200 63 47.625 25.4 14 35 36 13.1 3 17315R 17315L 315 325.5 240 80 47.625 25.4 14 35 44 24.5 4 P Steel M Stainless Steel Cast Iron on-ferrous Metal S Exotic Alloy ardened Steel 5 17.00 R0.8 ø15.875 ø4.4 IG EF 100608DE-G 5 120 6.00 Double Screw Clamp Wrench 159 ISO ardness Cutting Speed c m/min Feed Rate z mm/t Cast Iron 250B 200-250-300 0.15-0.23-0.30 AC200 ote WB6-20T GRW TTX20 165
GRM 17000 Type Roughing of Cast Iron Rake Radial Axial -6 6 60 P M Steel Stainless Steel Cast Iron on-ferrous Metal Aluminum S Exotic Alloy ardened Steel 1 2 3 4 X SFMS B ø13 ø35 X SFMS B X SFMS B 4-ø18 X SFMS ø177.8 B 4-ø18 4-ø22 IG Body Inch (R) (L) Diameter Max. Diameter Boss eight ole Size Grooving Width Grooving Depth Mounting Depth Total Weight X SFMS B Teeth (kg) GRM 17080R GRM 17080L 80 90.5 60 50 25.4 9.5 6 25 8 1.2 1 17100R 17100L 100 110.5 70 50 31.75 12.7 8 32 10 1.7 2 17125R 17125L 125 135.5 80 63 38.1 15.9 10 38 12 2.9 2 17160R 17160L 160 170.5 100 63 50.8 19.1 11 38 16 4.5 2 17200R 17200L 200 210.5 150 63 47.625 25.4 14 35 20 7.3 3 17250R 17250L 250 260.5 200 63 47.625 25.4 14 35 24 13.1 3 17315R 17315L 315 325.5 240 80 47.625 25.4 14 35 28 24.5 4 Inserts Application igh Speed/Light General Purpose Roughing Coated Carbide AC100 AC200 AC300 P Steel M Stainless Steel Cast Iron on-ferrous Metal S Exotic Alloy ardened Steel 5 17.00 R0.8 ø15.875 ø4.4 EF 100608DE-G 5 120 6.00 Double Screw Clamp Wrench 159 ISO ardness Cutting Speed c m/min Feed Rate z mm/t Cast Iron 250B 200-250-300 0.15-0.23-0.30 AC200 ote WB6-20T GRW TTX20 166
Rake Radial Axial 14to 6 5 8 45 igh Feed Roughing for Cast Iron P Steel M Stainless Steel Cast Iron on-ferrous Metal Aluminum S Exotic Alloy ardened Steel SEC-GoalMill GRV 16000 Type 1 2 3 4 BD BD BD SFMS SFMS SFMS B B B ø13 ø20 4-ø18 BD SFMS ø177.8 ø101.7 B 4-ø18 4-ø22 Body Inch (R) (L) Diameter Max. Diameter Boss eight ole Size Grooving Width Grooving Depth Mounting Depth Total Weight BD SFMS B Teeth (kg) GRV 16080R GRV 16080L 80 104 60 50 25.4 9.5 6 25 9 1.9 1 16100R 16100L 100 124 70 50 31.75 12.7 8 32 12 3.2 2 16125R 16125L 125 149 80 63 38.1 15.9 10 38 15 4.3 2 16160R 16160L 160 184 120 63 50.8 19.1 11 38 18 5.7 2 16200R 16200L 200 225 150 63 47.625 25.4 14 35 24 8.1 3 16250R 16250L 250 275 200 63 47.625 25.4 14 35 30 13.5 3 16315R 16315L 315 340 240 80 47.625 25.4 14 35 36 21.6 4 Inserts P Steel M Stainless Steel Cast Iron on-ferrous Metal S Exotic Alloy ardened Steel 5 184 12.7 R0.8 ø4.6 Check that there are no obstacles in the way of the outer edge of the cutter. IG 90 Application 16.1 6.29 Coated Carbide igh Speed/Light General Purpose Roughing Cutter External Diameter BD Max. Cutter Diameter Obstacle AC100 AC200 AC300 LMX 160608PS-G 5 160608PS- Screw Wrench Anti-seizure Cream m BFTX0412 3.0 TTX15W SUMI-P 159 ardness Cutting Speed c m/min Feed Rate z mm/t Cast Iron 250B 200-250-300 0.15-0.23-0.30 ote AC200 AC300 m Recommended Tightening Torque (m) 167