Surface Mount PR Transient Voltage Suppressors Uni-directional 500 W TVS in TO-277 (SMPC) Package esmp Series 2 TO-277 (SMPC) PRIMRY CHRCTERISTICS V WM 5.8 V to 43.6 V V BR 6.8 V to 5 V P PPM 500 W T J max. 85 C Polarity Uni-directional Package TO-277 (SMPC) TYPICL PPLICTIONS node Cathode Cathode 2 Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. FETURES Junction passivation optimized design passivated anisotropic rectifier technology vailable T J = 85 C capability suitable for high reliability and automotive requirement Very low profile - typical height of. mm Ideal for automated placement Uni-direction only Excellent clamping capability Low incremental surge resistance Very fast response time Meets MSL level, per J-STD-020 EC-Q0 qualified Material categorization: for definitions of compliance please see www.vishay.com/doc?9992 MECHNICL DT Case: TO-277 (SMPC) Molding compound meets UL 94 V-0 flammability rating Base P/NHM3_X - halogen-free, RoHS-compliant, and EC-Q0 qualified ( X denotes revision code e.g., B,...) Terminals: matte tin plated leads, solderable per J-STD-002 and JESD 22-B02 HM3 suffix meets JESD 20 class 2 whisker test RTINGS (T = 25 C, unless otherwise noted) PRMETER SYMBOL VLUE UNIT Peak power dissipation with a 0/0 μs waveform (fig. 3) ()(2) P PPM 500 W Peak power pulse current with a 0/0 μs waveform (fig. ) () See next table Peak forward surge current 8.3 ms single half sine-wave (2) I FSM 200 Maximum instantaneous forward voltage at (3) V F 3.5 V Operating junction and storage temperature range T J, T STG -65 to +85 C Notes () Non-repetitive current pulse, per fig. 3 and derated above T = 25 C per fig. 2 (2) Measured on 8.3 ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum (3) Pulse test: 300 μs pulse width, % duty cycle Revision: 04-Nov-6 Document Number: 89056 RE SUBJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
ELECTRICL CHRCTERISTICS (T = 25 C, unless otherwise noted) DEVICE TYPE DEVICE MRKING CODE BREKDOWN V BR () T I T (V) MX. TEST CURRENT I T (m) STND-OFF V WM (V) Notes () V BR measured after I T applied for 300 μs, I T = square wave pulse or equivalent (2) Surge current waveform per fig. 3 and derated per fig. 2 (3) ll terms and symbols are consistent with NSI/IEEE C62.35 REVERSE LEKGE T V WM I R (μ) REVERSE LEKGE T V WM T J = 50 C I D (μ) PEK PULSE SURGE CURRENT (2) () CLMPING T V C (V) TPC6.8 DEP 6.45 7.4 0 5.80 500 0 000 43 0.5 TPC7.5 DGP 7.3 7.88 0 6.40 500 5000 33.3 TPC8.2 DKP 7.79 8.6 0 7.02 200 2000 24 2. TPC9. DMP 8.65 9.55.0 7.78 50 500 2 3.4 TPC0 DPP 9.5 0.5.0 8.55 20 200 03 4.5 TPC DRP 0.5.6.0 9.40 5.0 50 96.2 5.6 TPC2 DTP.4 2.6.0 0.2 2.0 0 89.8 6.7 TPC3 DVP 2.4 3.7.0. 2.0 0 82.4 8.2 TPC5 DXP 4.3 5.8.0 2.8.0 0 70.8 2.2 TPC6 DZP 5.2 6.8.0 3.6.0 0 66.7 22.5 TPC8 EEP 7. 8.9.0 5.3.0 0 59.5 25.2 TPC20 EGP 9.0 2.0.0 7..0 0 54.2 27.7 TPC22 EKP 20.9 23..0 8.8.0 0 49.0 30.6 TPC24 EMP 22.8 25.2.0 20.5.0 0 45.2 33.2 TPC27 EPP 25.7 28.4.0 23..0 0 40.0 37.5 TPC30 ERP 28.5 3.5.0 25.6.0 0 36.2 4.4 TPC33 ETP 3.4 34.7.0 28.2.0 0 32.8 45.7 TPC36 EVP 34.2 37.8.0 30.8.0 5 30. 49.9 TPC39 EXP 37. 4.0.0 33.3.0 5 27.8 53.9 TPC43 EZP 40.9 45.2.0 36.8.0 20 25.3 59.3 TPC47 FEP 44.7 49.4.0 40.2.0 20 23. 64.8 TPC5 FGP 48.5 53.6.0 43.6.0 20 2.4 70. ORDERING INFORMTION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PCKGE CODE BSE QUNTITY DELIVERY MODE TPC0HM3_/H () 0.0 H 500 7" diameter plastic tape and reel TPC0HM3_/I () 0.0 I 6500 3" diameter plastic tape and reel Note () utomotive grade Revision: 04-Nov-6 2 Document Number: 89056 RE SUBJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
Peak Pulse Power (P PP ) or Current (I PP ) Derating in Percentage (%) P PPM - Peak Power (kw) www.vishay.com RTINGS ND CHRCTERISTICS CURVES (T = 25 C, unless otherwise noted) 0 0. 0. µs.0 µs 0 µs µs.0 ms 0 ms t d - Pulse Width (s) T = 25 C Non-Repetitive Pulse Waveform shown in Fig. 3 Fig. - Peak Pulse Power Rating Curve Junction Capacitance (pf) 0 000 0 V R measured at Stand-Off Voltage, V WM T J = 25 C f =.0 MHz V sig = 50 mv p-p 0 V BR - Breakdown Voltage (V) V R, measured at Zero Bias Fig. 4 - Typical Junction Capacitance 75 50 25 0 0 50 50 200 T J - Initial Temperature ( C) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Transient Thermal Impedance ( C/W) 0 0. 0.0 0. 0 0 T p - Pulse Duration (s) R thj, by mounted on recommended PCB 2 oz. area Fig. 5 - Typical Transient Thermal Impedance - Peak Pulse Current, % I RSM 50 50 t r = 0 µs Peak Value Half Value - t d 0 0.0 2.0 3.0 4.0 t - Time (ms) T J = 25 C Pulse Width (t d ) is defined as the Point where the Peak Current decays to 50 % of I PP 2 0/0 µs Waveform as defined by R.E.. Fig. 3 - Pulse Waveform Revision: 04-Nov-6 3 Document Number: 89056 RE SUBJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
PCKGE OUTLINE DIMENSIONS in inches (millimeters) TO-277 (SMPC) 0.87 (4.75) 0.75 (4.45) 0.06 (0.40) 0.006 (0.5) 0.262 (6.65) 0.250 (6.35) 0.242 (6.5) 0.238 (6.05) 2 0.7 (4.35) 0.67 (4.25) 0.047 (.20) 0.039 (.00) 0.46 (3.70) 0.34 (3.40) 0.087 (2.20) 0.075 (.90) Mounting Pad Layout 0.89 (4.80) 0.89 (4.80) 0.73 (4.40) 0.55 (3.94) NOM. 0.268 (6.80) 0.86 (4.72) 0.030 (0.75) NOM. 0.049 (.24) 0.037 (0.94) 0.050 (.27) 0.084 (2.3) NOM. 0.053 (.35) 0.04 (.05) Conform to JEDEC TO-277 0.04 (.04) 0.055 (.40) Revision: 04-Nov-6 4 Document Number: 89056 RE SUBJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
Legal Disclaimer Notice Vishay Disclaimer LL PRODUCT, PRODUCT SPECIFICTIONS ND DT RE SUBJECT TO CHNGE WITHOUT NOTICE TO IMPROVE RELIBILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. ll operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 207 VISHY INTERTECHNOLOGY, INC. LL RIGHTS RESERVED Revision: 08-Feb-7 Document Number: 90