Outputs C 199 YEARS 017 High-End Building anagement C Outputs 13 ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-R1U 1-gang relay 16 A fr flush-munting The C-R1U is a relay withut its wn prcessr fr flush wall munting with a ptential free cntact fr cnnecting t an C-UPP, C-UP4 r C-UPS. Usage n every C mdule with a T-Prt cnnectin is pssible. 14 escriptin: With this relay mdule, the user is prvided with an additinal switch cntact fr each C-UPP. This can especially be used fr electrical scket switching r fr regulating heater cntrl drives. As well as this, tw f the C-UPP electrnic utputs still remain available fr use. Hardware equipment: 1 switch cntact 30V 16A (AC1) Cable with plug fr the T-Prt cnnectin t intelligent bus mdules such as the C-UPP r C-UPS T-Prt scket fr further cnnectin f T-Prt peripheries Status E te: The relay cntact f the C-R1U has been ptimised fr high starting currents (AgSnO). A minimum lad f 0V/100mA is needed t prevent xidisatin f the cntacts. T run the C-R1U the signal-sund functin f the cnnected intelligent bus-mdule has t be turned ff. Fr mre detailed infrmatin please refer t installatin instructin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
auer C-R1U 1-gang relay 16 A fr flush-munting Outputs Technical ata: Cnnectin: Pwer supply: Pwer capacity: 30V AC ±0%, 50Hz (115V AC ±15% type available) <0,35W Cnnectin pwer side: itz wires 0,75 mm (with insulated ferrules) imensins: Terminals: Cable type: screwless max.16a, single r multi-cre (max.,5mm ) r with insulated ferrules (max.1,5mm ) Ø x H: 50mm 50mm x 0mm Relay: minal vltage: ax.starting current: Operatin current: Cntact vltage: Cntact material: 16A / AC1(Ohm s read) 70A 100mA -16A >0V AgSnO 15 Prts: T-Prt 43mm General details: Operating temperature: Humidity: -10 C t +40 C max. 80% rel., nn cndensing Envirnmental cnditins: statinary installatin accrding t VE 63, VE 637 Assembly: de-centralized installatin in deep flush-munted bx Safety classificatin: IP 0 Circuit diagram C-R1U ISSEORFF KG C-UPP =blue/blau =black/schw. U =30V, P V<0,35W I =16A/30V, AC1 T-Prt T ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-RU -gang relay 8 A fr flush-munting The C-RU is a gang islatin relay fr pattress bxes t cnnect t C-UPP mdules. It has independently cntrllable 8A nrmally pen cntacts. The excitatin vltage is 30V AC. Internally, the device runs with C ensuring silent peratin. escriptin: 16 In rder t galvanically separate inductive r capacitive lads frm the UP mdule, the relay mdule C-RU is simply switched between mdule and device. It is especially suitable fr cntrlling mtrs fr shutters and blinds. The C-RU can be used independently f the C system as a hum-free duble relay. Hardware equipment: nrmally pen switch cntacts 8A /AC1 Status E alternating cntacts 8A /AC1 are available as an ptin n request (eg. peratin f a shutter mtr) te: The relay cntacts f the C-RU are ptimized fr high starting currents (AgSnO). A minimum lad 1V/100mA is needed t prevent xidisatin f the cntacts. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-RU -gang relay 8 A fr flush-munting Outputs Technical ata: Cnnectin: Supply vltage: Input pwer: 30V AC ±0%, 50Hz (110V AC ±15% type available) <0,4W terminals: Cable type: screwless single r multi-cre, (max.,5mm ) r with insulated ferrules (max.1,5mm ) imensins: Ø x H: 50mm 50mm x 0mm Relay: minal current: ax. starting current: Operatin vltage: Cntact vltage: Cntact material: General details: Operating temperature: Humidity: Envirnmental cnditins: 8A/AC1(resistive lad) 70A 100mA - 8A >1V AgSnO -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63, VE 637 17 Safety classificatin: IP 0 43mm Assembly: de-centralized installatin in deep flush-munted bx Circuit diagram (Example: Cntrl f a mtr fr shutters) C-RU ISSEORFF KG U =30V, P V<0,3W/Kanal I auer=8a, AC1 C-UPP ila Ausgang 1 Speisung Braun Ausgang A A1 ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-FI1 Suppressing filter fr flush-munting The C-FI1 serves as a suppressin filter when using the C- UPP. Fr each utput it ffers its wn filter segment and a lad capacity f 300VA. Furthermre, it prtects the utputs frm vltage peaks. escriptin: 18 The C-FI1 filters ut unwanted harmnics while dimming within the requirements f the CE nrm. It als prtects against vltage peaks caused by inductive lads (e.g. flurescent lamps with electrnic ballasts). Hardware equipment: Screwless clips te: The C-FI1 need nly be used with the C-UPP mdule. The I rail munted bus mdules already have an integrated filter. When using mtrs, the relay C-RU is recmmended. Fr mre detailed infrmatin please refer t the installatin instructin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
max BI /Kanal C-FI1 Suppressing filter fr flush-munting Outputs Technical ata: Cnnectin: Supply vltage 30V AC ±0%, 50Hz (110V AC ±15% type available) Terminals: Cable type: screwless single r multi-cre (max.,5mm ) r with insulated ferrules (max.1,5mm ) imensins: Fuse: 3,15AF external Ø x H: 50mm 50mm x 0mm General details: Operating temperature: Humidity: Envirnmental cnditins: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63,VE 637 19 Safety classificatin: IP 0 43mm Assembly: de-centralized installatin in deep flush-munted bx Circuit diagram C-FI1 ISSEORFF KG C-UPP U =30V, I =1,5A, I =5mA ila A1 Phase Schwarz Braun A A A1 ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-R SI-/AI cntrller fr flush-munting The C-R is an interface fr cntrlling digital electrnic ballasts with AI r SI prtcls. It is used in cnjunctin with the C-UPP, C-UP4 r the C-UPS mdules. escriptin: 130 The C-R cuples pattress bx mdules with SI r AI electrnic ballasts fr dimming flurescent lamps. Hardware equipment: SI utputs / 1 AI utputs Cable fr T-Prt cnnectin t C-UPP, C-UPS T-Prt scket fr further cnnectin f T-Prt peripheries te: The C-R cntrl cable is referenced t eutral! When using with bus mdules C-UPS r C-UP4 the SI ballasts must be perated n cntinuus phase as the utputs A1 and A are nt present n these bus mdules. This is hwever in accrdance with the manufacturers' recmmendatins. Electrnic ballasts differ frm manufacturer t manufacturer: fr address allcatin use the cntrl unit f the respective ballast manufacturer. Ballasts frm TRIOIC can nly be used in SI mde. Parallel peratin with EIB key pads is nly pssible with C mdules built after 08/004. The C-R mdule can nt be used in cnjunctin with the C- SH r the C-A1. Fr mre detailed infrmatin please refer t the installatin instructin manual. Infrmatin t AI: In AI mde nly the first utput is wired up. All f the AI ballasts are cnnected tgether in parallel n this cntrl line. Electrnic ballasts differ frm manufacturer t manufacturer: fr address allcatin use the prgramming device f the respective ballast manufacturer. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-R SI-/AI cntrller fr flush-munting Outputs Technical ata: Cnnectin: Supply vltage: Input pwer: 30V AC ±0%, 50Hz (110 V AC ±15% type available) <1W Cnnectin pwer side: itz wires 0,75 mm (with insulated ferrules) imensins: Ø x H: 50mm 50mm x 0mm Terminals: Cable type: SI-ad: AI-ad: screwless, max. 16A single r multi-cre max.,5 mm r with insulated ferrules (max. 1,5mm ) 10 ballasts per utput ( SI utputs) 16 fr AI ballasts (1 AI utput) 131 General details: Operating temperature: Humidity: -10 C t +40 C max. 80% rel., nn cndensing 43mm Envirnmental cnditins: Safty Clasificatin: statinary installatin accrding t VE63, VE637 IP 0 Assembly: de-centralized installatin in deep flush-munted bx Circuit diagram max. 10 per utput Output 1 Output max. 16 elctrnic ballasts max. 10 per utput C-bus mdule T C-R ISSEORFF KG Schwarz / black Blau / blue 30V~ 50 / 60Hz P V<1W SI TSI AI : : 1 T 1 T-Prt dul SI SI Vrschaltgerät SI Vrschaltgerät Vrschaltgerät SI Eingang SI asse SI Eingang SI asse SI Eingang SI asse AI AI Vrschaltgerät AI Vrschaltgerät Vrschaltgerät A A A A A A SI SI Vrschaltgerät SI Vrschaltgerät Vrschaltgerät SI Eingang SI asse SI Eingang SI asse SI Eingang SI asse OER A1 dera A1 A1 dera ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-R8H Relay mdule 8 x 16 A utputs fr I rail munting The C-R8H is an 8 relay blck fr the C Bus system. It must be cnnected t an intelligent bus mdule such as C-SH, C-HU r C- The ptential free 16A cntacts are ptimized fr high starting currents. escriptin: 13 The C relay blck is used t cntrl up t eight independent circuits/devices r up t fur independently cntrlled mtr drives. A cmbinatin f the abve is pssible. Hardware equipment: 8 lad relays and ptential free switch cntacts fr lad switching at 50V/16A AC1 3600VA switching capacity (each cntact) Cable with plug fr P-Prt cnnectin t the intelligent bus mdule Plug- in relays te: The C-R8H's relay cntacts are ptimised fr high starting currents (AgSnO). A minimum lad f 0V 100mA is needed t prevent xidisatin f the cntacts. When planning the cntact lads pay special attentin t the starting and reactive currents. Fr media applicatins gld cntact relays are available as an ptin. Fr mre detailed infrmatin please refer t the installatin instructin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-R8H Relay mdule 8 x 16 A utputs fr I rail munting Outputs Technical ata: Cnnectin: Supply vltage: Input pwer: 30V AC ±0%, 50Hz (110V AC ±15% type available) <W imensins: ( x W x H): 114 mm x 9 mm x 66 mm 114mm (6,5TE) Terminals: Cable type: Relays: minal current: ax. starting current: Cntact current: Cntact vltage: Cntact material: screwless max.16a single r multi-cre (max.,5mm ) r with insulated ferrules (max.1,5mm ) 16A / AC1(resistive lad) 70A 100mA - 16A >0V AgSnO 133 9mm 66mm 61mm General details: Operating temperature: Humidity: Envirnmental cnditins: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63,VE 637 37mm Safety classificatin IP 0 Height: 66mm 61mm via I rail Space requirement: 6,5 TE Assembly: REG n 35 mm munting rail (I 500) Circuit diagram Example: cntrl f mtrs and 4 lighting circles C Bus dule fr I RAI cal Cntrl etwrk C 8 x ( ) C-R8H 8-fach Relaisblck 8 x Relais ISSEORFF U =30V, P V =W,I Spitze=16A,I auer=1a P P 8 7 6 5 4 3 1 30V ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-R4H Relay mdule 4 x mtr utputs fr I rail munting The C-R4H is a relay blck fr cntrlling up t eight mtrs (4x tw mtrs parallel) fr the C Bus system. It must be cnnected t an intelligent bus mdule such as the C- SH, C-HU r C-. The cntacts are pre-wired and cnnected t clips making it simple t cnnect and cntrl 30V mtrs. escriptin: 134 The C-R4H relay blck is used t cntrl up t eight 30V mtr drives enabling cntrl f 4 mtr pairs in parallel. It is designed fr use with slar shading systems such as shutter cntrl. Used in cnjunctin with binary sensrs (C-B8x and C-BS4), it enables accurate psitin cntrl. Hardware equipment: 8 relays fr lad switching with ptential free cntacts (.O and.c) pre- wired fr use with mtrs at 50V /8A, AC 1 1800VA switching capacity; max. 3600VA circuit pwer Cable with plug fr P-Prt cnnectin t the intelligent bus mdule Plug in relays te: A minimum lad f 5V 10mA is needed t prevent xidisatin f the cntacts. This is less than that f ther relay blcks due t the cntact material ( Agi 90/10). This hwever renders the relay blck less resistant t current surges than ther relay blcks such as the C- R8H. When planning the cntact lads pay special attentin t the starting and reactive currents. Fr mre detailed infrmatin please refer t the installatin instructin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-R4H Relay mdule 4 x mtr utputs fr I rail munting Outputs Technical ata: Cnnectin: Supply vltage: 30V AC ±0%, 50Hz (110V AC ±15% type available) Input pwer: <W imensins: ( x W x H): 85,5 mm x 9 mm x 66 mm 114mm (5,5TE) Terminals: Cable type: Relay: minal current: ax. starting current: Operatin current: Rec. cntact vltage: Cntact material: screwless max. 16A single r multi-cre max.,5mm r with insulated ferrules (max.1,5mm ) 8A / AC1 (resistive lad) 30A 10mA - 8A / per mtr (max. 16A ttal / all mtrs) >5V Agi 90/10 135 9mm 66mm 61mm General details: Operating temperature: Humidity: Envirnmental cnditins: Safety classificatin: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63, VE 637 IP 0 37mm Height: 66mm 61mm via I rail Space requirement: 5,5 TE Assembly: REG n 35 mm munting rail (I 500) Circuit diagram 4b 4a 3b 3a b a 1b 1a C Bus dule fr I RAI cal Cntrl etwrk 4 x C 4b x 4a 3b 3a b 1a a 1b 1b 1a P 4 3 ISSEORFF 1 C-R4H 4x-fach traktr Relay 1 (3/5/7) Relay (4/6/8) Pwer-Relay irectin-relay RT3104 RT4404 ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-RH Relaismdul mit Ausgängen für die Hutschiene The C-RH prvides tw 30V/16A cntact switching relays. He can be extended with a secnd C-RH. escriptin: 136 The C relay blck is used t cntrl tw independent circuits/devices r fr a single mtr drive. Hardware equipment: relays fr lad switching at 50V/16A AC1 3600VA switching capacity (each cntact) Cable with plug fr the P-Prt cnnectin t the intelligent bus mdule P-Prt scket fr cnnectin t an additinal C-RH Plug in relays te: The relay cntacts f the C-RH are ptimized fr high starting currents (AgSnO). A minimum lad f 0V 100mA is needed t prevent xidisatin f the cntacts. When planning the cntact lads pay special attentin t the starting and reactive currents. Fr use with media applicatins, relays with gld cntacts are available as an ptin. Fr mre detailed infrmatin please refer t the installatin instructin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-RH Relaismdul mit Ausgängen für die Hutschiene Outputs Technical ata: Cnnectin: Supply vltage: Input pwer: 30V AC ±0%, 50Hz (110V AC ±15% type available) <W Terminals: Cable type: screwless, max. 16A single r multi-cre (max.,5mm ) r with insulated ferrules (max.1,5mm ) imensins: ( x W x H): 38 mm x 9 mm x 66 mm 38 mm ( TE) Relay: minal current: ax. starting current: Operatin pwer: Cntact vltage: Cntact material: 16A / AC1(Resistive lad) 70A 100mA - 16A >0V AgSnO 137 9 mm 66 mm 61 mm General details: Operating temperature: Humidity: Envirnmental cnditins: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63, VE 637 Safety classificatin: IP 0 37 mm Height: 66mm 61mm via I rail Space requirement: TE Assembly: REG n 35 mm munting rail (I 500) Circuit diagram: This example: rive cnnectin C bus mdule fr I RAI A R A R C C-RH -fach Relaisblck x Relais U =30V, P V=1W, I=16A P 1 P ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-AO1R Analgue utput cnverter: 30V / 0-10V fr flush-munting The C-AO1R transfrms the dimmed phase f the C-UPP immediately int an analgue 0-10V (1-10V) cntrl signal. In additin it prvides a 30V utput fr supplying electrical ballasts. escriptin: 138 The C-AO1R is mainly used fr fr cntrlling dimmable electrical ballasts with a 0-10V signal. Additinally, the C-AO1R has a 30V relay utput which always activates when the 0-10V utput is nt 0. The C-AO1R can cntrl devices with a 0-10V signal such as frequency cnverters, actuatrs fr ventilatin dampers r heating valve actuatrs. Hardware equipment: Input fr dimmed phase One utput 0-10V One Output 30V/8A Status display te: The C-AO1R nly wrks with the C-UPP. It can nt be used n the C-SH (because f its interference suppressin filter). Fr mre detailed infrmatin please refer t the installatin instructin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-AO1R Analgue utput cnverter: 30V / 0-10V fr flush-munting Outputs Technical ata: Cnnectin: Supply vltage: Input pwer: 30V AC ±0%, 50Hz (110V AC ±15% type available) < 0,8W Cnnectin pwer side: itz wires 0,75 mm (with insulated ferrules) Terminals: screwless, imensins: Ø x H: 50mm 50mm x 0mm 43mm Cable type: Cnductr typ 0-10V: Output: Relay utput: 0-10V utput: single r multi-cre max.,5 mm r with insulated ferrules (max. 1,5mm ) max. 0,8 mm Relay 30V, max. 8A Surce current: max. 1,5mA (aktive) ad current: max. 40mA (ca. 40 EVGs with enquiry current under 1mA/elec. ballasts) The 0-10V Output is n - ptential. 139 Assembly: de-centralized installatin in deep flush-munted bx General details: Operating temperature: Humidity: Envirnmental cnditins: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE63, VE637 Safety classificatin: IP 0 Circuit diagram C-UPP C-AO1R ISSEORFF KG Schwarz / black Blau / blue 30V~ 50 / 60Hz P V<0,5W 0-10V elctrnic ballasts 0-10V elctrnic ballasts 0-10V 0-10V G 0-10V G Output 1 r C-UPP ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Gateways C-XH X 51 aster / Slave Cntrller The C-XH cntrller is used t cntrl the 4 X channels, e.g. RGBW electrnic ballasts. It must be cnnected t an intelligent bus mdule frm firmware 170.. (Feb. 013). escriptin: 140 The C mdule prvides the brightness values f its 4 electrnic utputs n the I-prt t the C-XH. The C-XH cnverts these values t the crrespnding freely cnfigurable X channels. The C-XH can be lped int an existing X line via existing X utput. The C-XH uses its 4 dimming values in 4 (adjustable) X addresses. It is als pssible t cnnect up several C-XH in series t cntrl 8, 1,... r mre channels. Hardware equipment: C-XH I-prt cable te: The fllwing periphery shuld nt be cnnected at the same time: C-GT4/-GT10. Fr mre detailed infrmatin please refer t the installatin manual. ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
C-XH X 51 aster / Slave Cntrller Gateways Technical ata: Cnnectin: Supply vltage: Input pwer: 30V AC ±15%, 50/60Hz (110V type available) 3W Terminals: Screwless, max. 16A imensins: ( x W x H): 38 mm x 9 mm x 66 mm 38 mm ( TE) Cable type: Output Output vltage: Terminals / Cnductr Type : Single r multi cre max.,5mm r with insulated ferrules 1,5mm accrding t X - 51A specificatin, pled interface slid r strand 0,5-1,5mm² 141 umber X participants : ax. 3 ttal 9 mm 66 mm 61 mm General details: Operating temperature: Humidity: Envirnmental cnditins: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63,VE 637, 37 mm Safety classificatin: IP 0 Height: 66mm 61mm via I rail Space requirement: TE Assembly: REG n 35 mm munting rail (I 500) Circuit diagram: X- RGBW-Headlight X- ixer (ptin) C C-SHS Sensr-dul Cntrller U =30V, P V=0.4W C C-XH I-Anschluss- X aster/slave Cntrller U =30V AC The cnsle als cntrls channel 11 + 1. The XH additinally cnfigured with the C - PRO channels 18, 19, 130 & 131 Channel 18, 19, 130 & 131 X-ixer cntrlls channel 11+1 (example) - + - + X- Headlight X- Headlight channel 11 channel 1 ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
Outputs C-H4 E 4-channel dimmer fr I rails The 4 - channel dimmer is designed fr a simple and flexible cntrl f E s with a cnstant vltage ( usually an E strip). It cnnects t an C mdule with firmware 170 1 (Feb. 013) r after, n the I-prt. Fields f applicatin: 14 The C-H4 can be cnnected t all intelligent C mdules - preferably where the utputs are nt being used fr ther purpses, e.g. t the C-SHS. The brightness values f the (virtual) electrnic utputs 1-4, are transferred ver the I-cnnectin f the C-H4. The C-H4 cnverts these values int a PW signal fr E s. The C-H4 masters the cntrls f the E s accrding t the HSB and RGB clur pattern. Clur saturatin, brightness and clur value, can be cntrlled separately ver the HSB clur pattern. Hardware features: C-H4 I-prt cable Functinality: RGB clur pattern (switch psitin ) The utputs are cnverted 1:1 t RGB. Output 1 cntrls red, utput cntrls green, utput 3 cntrls blue and utput 4 cntrls the white E. It is nt easy t adjust with a certain clur brightness: all fur utputs must be dimmed in a cnstant mixing. HSB clur pattern (switch psitin 1) The desired settings are achieved by adjusting the clur (hue), the saturatin (saturatin) and the brightness (brightness). tes: There is still a 1 / 4V C pwer supply (with verlad prtectin) required! The pwer supply used must be pulse slid, stable vltage and prvide a pwer reserve f arund 30%. Fr detailed infrmatin, please refer t the installatin guide. E 4-channel dimmers fr E / RGB / RGBW E cntrl with HSB & RGB clur pattern Operatin n the I-prt cnnectin f the C mdules OUTPUT 1 brightness 0% 100% OUTPUT saturatin 0% 100% 90,5% 180 45% OUTPUT 3 clur (hue) 0% 0 360 90% 70 67,5% ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
I C B A 9 8 5 7 6 C-H4 E 4-channel dimmer fr I rails Outputs Technical data: Cnnectin: supply vltage: 1-4V C ( pwer supply with ver- lad prtectin use ) <1W pwer cnsumptin terminals: screwless, max. 16A cable type: single r multi cre max.,5mm r with insulated ferrules 1,5mm imensins: ( x W x H): 68 mm x 9 mm x 66 mm 68mm (4TE) Electrnic utputs: utput pwer: utput vltage: utput current ttal: 10W ( at 4V C ) utput cnstant vltage, dimming via PW signal 00Hz 5A 143 utput current per channel: 1.5A r single-channel 5A 9mm 66mm 61mm Prts: I-prt: I-cnnectr, electrically islated, cable length 300mm (pluggable), with C-IVH extended t max. 50m. Height: 66mm 61mm via I rail 37mm General details: perating temperature: humidity: envirnmental cnditins: safety classificatin: -10 C t +40 C max. 80% rel., nn cndensing statinary installatin accrding t VE 63, VE 637, IP 0 Space requirement: 4TE Assembly: REG n 35 mm munting rail (I 500) Circuit diagram: example RG B W C C C-SHS Bus mdule Sensr-dul Cntrller U =30V, P V=0.4W 1-4C pwer supply cal Cntrl etwrk 1 3 4 R G B W C C-H4 E 4-channel dimmer 10W ISSEORFF U =1V/4V C, P V=W I E F 0 1 3 4 t the I-prt cnnectin rtary switch test buttn ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu
144 ISSEORFF KG agdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu