Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
v.51 HMC32LC Typical Applications The HMC32LC is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios & VSAT Test Equipment & Sensors Military End-Use Functional Diagram Features Noise Figure: 3.5 db Gain: 22 db Single Positive Supply: +3V @ 3 ma 5 Ohm Matched Input/Output RoHS Compliant x mm SMT Package General Description The HMC32LC is a GaAs phemt MMIC Low Noise Amplifier housed in a leadless x mm RoHS compliant SMT package. Operating from 13 to 25 GHz, the amplifier provides 22 db of gain and +19 dbm of output IP3 from a single +3V supply. The low noise figure performance of 3.5 db is ideal for receive and transmit pre-driver applications. The RF I/Os are DC blocked and matched to 5 Ohms for ease of use. The HMC32LC allows the use of surface mount manufacturing techniques and requires no external matching components. Electrical Specifications, T A = +25 C, Vdd = +3V, Idd = 3 ma Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units Frequency Range 13-18 18-22 22-25 GHz Gain 19 22 17 2 16 19 db Gain Variation Over Temperature.25.35.25.35.25.35 db/ C Noise Figure 3.5. 3.5. 3.5.5 db Input Return Loss 15 15 1 db Output Return Loss 15 2 15 db Output Power for 1 db Compression (P1dB) 7 8 9 dbm Saturated Output Power (Psat) 9 11 11.5 dbm Output Third Order Intercept (IP3) 16 19 2 dbm Supply Current (Idd) (Vdd = +3V) 3 3 3 ma 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 182 Phone: 978-25-333 Fax: 978-25-3373 Order On-line at www.hittite.com Application Support: Phone: 978-25-333 or apps@hittite.com
v.51 HMC32LC Broadband Gain & Return Loss Gain vs. Temperature RESPONSE (db) 25 2 15 1 5-5 -1-15 -2-25 -3 8 1 28 3 S21 S11 S22 Input Return Loss vs. Temperature RETURN LOSS (db) -5-1 -15-2 GAIN (db) 28 25 22 19 16 13 1 Output Return Loss vs. Temperature RETURN LOSS (db) -5-1 -15-2 -25-25 -3-3 Noise Figure vs. Temperature 1 Output IP3 vs. Temperature 2 NOISE FIGURE (db) 8 6 2 IP3 (dbm) 22 2 18 16 1 12 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 182 Phone: 978-25-333 Fax: 978-25-3373 Order On-line at www.hittite.com Application Support: Phone: 978-25-333 or apps@hittite.com 2
v.51 HMC32LC P1dB vs. Temperature 1 Psat vs. Temperature 1 P1dB (dbm) 12 1 8 6 2 Power Compression @ 2 GHz Pout (dbm), GAIN (db), PAE (%) 2 19 1 9-1 Pout Gain PAE Psat (dbm) Reverse Isolation vs. Temperature ISOLATION (db) 12 1 8 6 2-1 -2-3 - -5-6 -26-2 -22-2 -18-16 -1-12 -1-8 -6 - INPUT POWER (dbm) -6 GAIN (db), P1dB (dbm), Psat (dbm), NOISE FIGURE (db) 2 2 16 12 8 Gain, Power & Noise Figure vs. Supply Voltage @ 2 GHz Gain P1dB Psat Noise Figure 2.7 3 3.3 Vdd Supply Voltage (Vdc) 3 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 182 Phone: 978-25-333 Fax: 978-25-3373 Order On-line at www.hittite.com Application Support: Phone: 978-25-333 or apps@hittite.com
v.51 HMC32LC Absolute Maximum Ratings Typical Supply Current vs. Vdd Drain Bias Voltage (Vdd) RF Input Power (RFIN)(Vdd = +3. Vdc) Outline Drawing +5.5 Vdc dbm Channel Temperature 175 C Continuous Pdiss (T= 85 C) (derate 3.62 mw/ C above 85 C) Thermal Resistance (channel to ground paddle).326 W 276 C/W Storage Temperature -65 to +15 C Operating Temperature - to +85 C Vdd (Vdc) Idd (ma) +2.7 2 +3. 3 +3.3 Note: Amplifier will operate over full voltage ranges shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA. 2. LEAD AND GROUND PADDLE PLATING: GOLD FLASH OVER NICKEL. 3. DIMENSIONS ARE IN INCHES (MILLIMETERS).. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED.5MM DATUM C 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [2] [1] H32 HMC32LC Alumina, White Gold over Nickel MSL3 XXXX [1] Max peak reflow temperature of 26 C [2] -Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 182 Phone: 978-25-333 Fax: 978-25-3373 Order On-line at www.hittite.com Application Support: Phone: 978-25-333 or apps@hittite.com
v.51 HMC32LC Pin Descriptions Pin Number Function Description Interface Schematic 1, 5-1, 18-2, 22-2 N/C 2,, 15, 17 GND 3 RFIN 16 RFOUT 21 Vdd Application Circuit No connection required. These pins may be connected to RF/DC ground without affecting performance. Package base has an exposed metal ground that must also be connected to RF/DC ground. This pin is AC coupled and matched to 5 Ohms. This pin is AC coupled and matched to 5 Ohms. Power Supply Voltage for the amplifier. External bypass capacitors of 1 pf, 1pF, and 2.2 µf are required. Component Value C1 1 pf C2 1, pf C3 2.2 µf 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 182 Phone: 978-25-333 Fax: 978-25-3373 Order On-line at www.hittite.com Application Support: Phone: 978-25-333 or apps@hittite.com
v.51 HMC32LC Evaluation PCB Item Description J1, J2 2.92 mm PC mount K-connector J3, J DC Pin C1 1 pf capacitor, 2 Pkg.. C2 1, pf Capacitor, 63 Pkg.. C3 2.2µF Capacitor, Tantalum U1 HMC32LC Amplifier PCB [2] 18535 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 35. List of Materials for Evaluation PCB 1129 [1] The circuit board used in this application should use RF circuit design techniques. Signal lines should have 5 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 182 Phone: 978-25-333 Fax: 978-25-3373 Order On-line at www.hittite.com Application Support: Phone: 978-25-333 or apps@hittite.com 6