LARAMIE COUNTY COMMUNITY COLLEGE AUGUST, 07
FABRICATOR PERFORMANCE & MATERIAL REQUIREMENTS This document has been assembled by Tangram Design, LLC (Tangram) for College (Owner) with the expectation that the fabricator shall meet the following quality and performance requirements. The acceptance of these drawings by the Fabricator constitutes agreement to comply with the following conditions. The Owner will hold the Fabricator to these requirements as part of their contract obligations..0 GENERAL. Proprietary Information Non-Disclosure Agreement All ideas, designs, arrangements and plans indicated or presented by these drawings are the property of the Owner, and were created for use in connection with the specified project. The information in this document is confidential and shall not be disseminated to anyone other than the Owner, Tangram, or the Fabricator s personnel necessary to execute the contract, without the written permission of Owner and Tangram. In addition, the Fabricator must request and receive written approvals from both the Owner and Tangram to use images of any completed element. The Fabricator is responsible for ensuring that credit indicating Tangram Design, LLC as the Designer will accompany all images and articles related to the project. The Owner may have additional requirements or restrictions for which the Fabricator is also responsible.. Design Intent Drawings The design intent drawings contained in this document are for the sole purpose of expressing visual design intent and are not intended for construction purposes. All aspects of fabrication, installation, and any resulting working drawings, shop drawings, submittals and contract documents are the responsibility of the Fabricator. Within the design intent drawings: All written dimensions take precedence over dimensions otherwise implied by drawing scale, figures, etc. Large scale details take precedence over the smaller scale drawings. Specific recommendations for materials, colors, and content take precedence over representations shown in drawings. Prior to execution of the contract, Fabricator shall carefully review all the Contract Documents, Design Intent Drawings, Specifications, and/or instructions for any conflicts or ambiguities. Fabricator will identify any conflicts or ambiguities in writing to Owner and Tangram prior to execution of the agreement..0 PRE-FABRICATION REQUIREMENTS. Proposal Copies of all pricing and bid information shall be sent to the Owner and Tangram. The Fabricator shall base their proposal on the performance of all items of service including labor, materials, equipment, and resources required to complete fabrication and installation of the specified work. Full compliance with the these Fabricator Performance and Material Requirements will be required. Any further examinations, investigations, explorations, tests, studies, and/or specifications necessary for the performance of the work and/or services required is the Fabricator s responsibility and should be accounted for in the bid and schedule. The Fabricator is encouraged to make recommendations for specific changes if they will improve the quality or cost-effectiveness of fabrication while preserving Tangram s visual design intent. However, any such recommendations must be approved in writing by the Owner and Tangram at the time of bid. Should the Fabricator be contracted based on a proposal that assumes substitutions that have not been properly approved, the Fabricator shall be responsible for providing all elements as originally indicated at their own expense.. Shop Drawings The Fabricator shall submit for review and approval shop drawings of all fabricated items, product data and paint samples to the Owner and Tangram. This submission shall consist of detailed drawings that indicate all materials, finishes, construction details, lighting requirements, installation details, and artwork, including locations of all material seams. Drawings shall include elevations, plans, sections, details, and notes as required to clearly convey fabrication intent. Tangram shall advise and review all shop drawing submittals for fidelity and conformance with the design intent drawings. Upon review, the Fabricator shall make all requested revisions and resubmit as required. A complete set of approved shop drawings must be received from both the Owner and Tangram before production may begin. Required submittals must be issued in adequate time to coordinate a two week review and approval process without delaying the project schedule.. Samples and Prototypes The fabricator will provide samples of all paints used in the project for review and approval by Owner and Tangram. The fabricator will also supply to the Owner and Tangram agreed upon prototypes for review of fabrication methods, finishes and materials. Prototypes must be reviewed and approved prior to production. If approved, the prototype will be considered as part of the total sign count. If the prototype requires modifications, those changes must be made before it will be accepted. If the prototype is deemed to be defective and/or unfixable, based on the necessary modifications, the prototype will not be accepted as part of the final sign count. Fabricator will be responsible for any costs needed to repair or replace defective prototypes..0 FABRICATION & INSTALLATION REQUIREMENTS. Permitting & Regulation Compliance The Fabricator is responsible for securing and paying for all permits, insurances, inspections, and tests required by governmental agencies. The Fabricator is also responsible for verifying and ensuring compliance with all ADA, OSHA, environmental regulations, and all other applicable governing code requirements. All required resolutions or revisions to construction details must be approved by the Owner and Tangram prior to production.. Structural Requirements The Fabricator shall follow Tangram s drawings for exterior visual appearance, but designs of internal structure, engineered connections, mounting assemblies, and foundations are by the Fabricator. Structural design shall utilize self-supportive framing and prevent irregularities in exposed surfaces. The Fabricator shall provide the Owner and Tangram with calculations for all structural members and foundations and they must be sealed by certified engineers registered in the state of installation, prior to fabrication. The Fabricator shall provide the Owner and Tangram with a list of support and/or blocking requirements, and approximate weights for each element as required after final shop drawing approval. The Fabricator s installation responsibilities include the provision of any required footings, anchor bolts, or fastenings. All point-of-connection coordination is the responsibility of the Fabricator.. Labeling Visible labels, manufacturer s or otherwise, code permitting, shall not appear on any completed element. The placement of any required labels must be approved by Tangram prior to application and installation.. Artwork & Fonts Tangram will provide the Fabricator with layout guidelines and electronic artwork as required, however all final copy layouts are the responsibility of the Fabricator. The Fabricator shall legally acquire, at their own expense, all project fonts from the specified distributors, as necessary. Tangram will not provide copies of licensed fonts..5 On-Site Coordination and Installation All installation will be coordinated with the Owner. No installation shall be permitted without sign-off of construction and final location approval through the Owner. The Fabricator shall field verify all measurements indicated on drawings to establish correctness. Fabricator shall examine the site prior to executing this agreement so as to reasonably ascertain the nature of the work and the various conditions affecting the work. All locations shown in the enclosed location plans are approximate. The Fabricator is responsible for field verification and coordination of all final locations. The Fabricator is responsible for reviewing all building surfaces, which may include but is not limited to glass, stone, brick, drywall, concrete, etc., and for evaluating all methods of attachment. In instances where there is a glass surface, a sheet of vinyl must be used on the st surface of the glass to hide the attachment method. In instances where VHB tape will not work for installation, such as on stone or brick, other methods of attachment shall be used by the fabricator. The Fabricator shall notify the Owner and Tangram of any discrepancies between Tangram s drawings, location plans, or message schedule, and field conditions prior to sign fabrication. All required resolutions or revisions to construction details or installation processes must be approved by the Owner and Tangram prior to production. The Fabricator shall keep the site reasonably free from debris, trash and construction wastes resulting from the performance of the work. The Fabricator shall be responsible for cleaning up all work areas upon the completion of work on a daily basis. Upon completion of the work, Fabricator shall remove all debris, trash, construction wastes, materials, equipment, machinery and tools arising from the work. All finish surfaces at the base of the sign (lawn, mulch, brick, etc.) shall be repaired to match existing finish grade.
All installed items shall be left in a clean and as-new condition. The Fabricator shall be fully responsible for the security and quality of all equipment, materials, and installed components until they have been reviewed and accepted by the Owner. All installations are to be level and plumb or will not be accepted. Immediately after erection, clean bolted connections and abraced areas of shop paint. Paint exposed areas with same paint of finish used for shop painting. If marred areas cannot be adequately touched up on site, the sign will be returned to the shop for controlled refinishing..6 Inspection At all reasonable times, Fabricator shall provide sufficient facilities for inspection of the work by Owner or Tangram at the site and at all locations where portions of the work are in progress or various stages of completion. When appropriate portions of the work are ready for inspection, Fabricator shall notify Owner and Tangram..7 Safety The Fabricator recognizes the importance of performing the work in a safe manner so as to prevent damage, injury or loss to (i) all individuals at the site, whether working or visiting, (ii) the work, including materials and equipment incorporated into the work or stored on-site or off-site, (iii) the work of others on the project, and (iv) all other property at the site or adjacent thereto. Fabricator assumes responsibility for implementing and monitoring all safety precautions and programs related to the performance of the work. The Fabricator shall be responsible for providing barricade or protective coverings as necessary to safeguard the public and property during the performance and duration of their work. The Fabricator shall be fully responsible for any injuries to the public or damage to the buildings, site, and adjacent objects during installation..0 MATERIAL STANDARDS All materials, hardware, and finishes used to fabricate any and all components shall be new (i.e. not previously used or operated in any other application) from the most recent manufacturer s production supply and free from any defects impairing strength, durability or appearance..5 Systech Signage Technology All product pieces shall be the best commercial quality for the purposes specified and free from defects impairing strength, durability, or appearance. All Architectural Modular (AM) Series signage systems shall be tamper-proof. All signage systems shall match the specified finish. Products shall be warranted for a minimum of months from date of the Owner s acceptance. All Systech Signage Technology systems are to be supplied by Systech Signage Technology, contact Alicia Wiesman -800-807-9. 5.0 COMPLETION 5. Review & Punch List The Fabricator shall notify both the Owner and Tangram in writing when all work is completed. Upon notice, Tangram will review all work according to their contract with the Owner and prepare a punch list outlining incomplete or unsatisfactory items. The repair or replacement of work outlined on the punch list shall be coordinated between the Fabricator and the Owner. Fabricator shall correct any of the work that is found not to be in conformance at their own expense. 5. Final Deliverables Upon the Owner s acceptance of the work, the Fabricator shall provide the Owner with a complete service and maintenance manual for all products and finishes installed under their contract. This manual shall include, but is not limited to, product specifications such as manufacturer information, contact names and addresses, warranty information, technical data, and routine maintenance recommendations. 5. Warranties All warranty periods shall begin on the date of the Owner s acceptance of the work. All warranties shall include the materials and labor required to replace defective components. Fabricator warrants that all installed elements shall be free from material defects in workmanship and materials and shall substantially comply with applicable designs and specifications for a minimum of one year.. Metals Metals shall be the best commercial quality for the purposes specified and free from defects impairing strength, durability, or appearance. All joints must be welded, filled, ground and sanded smooth prior to painting to insure an uniform surface. All sheet metal shall have brake formed edges with radii not greater than sheet thickness. All metals must be treated to prevent corrosion and staining of other finishes. All aluminum materials must be thoroughly sanded to remove oxidation and primed prior to painting to insure maximum paint adhesion.. Fasteners All exposed fasteners shall be tamper-proof, resistant to oxidation and other corrosion, and painted to match adjacent surfaces. Concealed fasteners must be resistant to oxidation and other corrosion to prevent staining of other finishes.. Paints & Finishes All paints and finishes shall match exactly the color, finish, and texture noted. Unless otherwise noted, all pretreats, primers, coatings, and finishes shall be applied in strict accordance with the paint manufacturer s specifications to provide the highest level of ultraviolet light resistance, weatherability, and overall longevity for both the materials indicated, and the environmental conditions of the final install locations. Paints & finishes shall be warranted against color fading, UV damage, cracking, peeling, blistering, and other defects in materials or workmanship for a minimum of one year from date of Owner s acceptance. All paints shall be evenly applied without pinholes, scratches, orange peeling, application marks, and other imperfections. Workmanship with finishes and formation of letters shall conform to the highest standards of the trade.. Vinyl Film All vinyl sheeting shall match exactly the color, finish, and durability of the manufacturers product as noted. Unless otherwise noted, all vinyl sheeting shall be installed in strict accordance with the manufacturer s specifications to provide the highest level of ultraviolet light resistance, weatherability, and overall longevity for both the materials indicated, and the environmental conditions of the final install locations. Vinyl sheeting shall be warranted against color fading, UV damage, de-lamination, or peeling for a minimum of five years from date of Owner s acceptance. All letters forms shall be aligned to maintain a base line parallel to the sign format. Margins must be maintained as specified by sign panel layouts in the drawings. All vinyl cutting shall be executed in such a manner that all edges and corners of finished letter forms are true and clean.
BID REQUIREMENTS SIGN TYPE DESCRIPTION QUANTITY.A* Wall Mounted Directional.D Ceiling Mounted Directional.E Ceiling Mounted Directional.F Ceiling Mounted Directional.F* Ceiling Mounted Directional 5.A* Blade Mounted Identification 9 7.C Ceiling Mounted Identification 7.D Wall Mounted Identification 0.A Ceiling Mounted Identification.A* Elevator Directory.A Wall Mounted Identification * A full-scale prototype is required for this sign type. If approved, the prototype will be considered as part of the total sign count. If the prototype requires modifications, those changes must be made before it will be accepted. If the prototype is deemed to be defective and/or unfixable, based on the necessary modifications, the prototype will not be accepted as part of the final sign count. Fabricator will be responsible for any costs needed to repair or replace defective prototypes.
ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 567890&? CLEARVIEW ADA CONDENSED MEDIUM WAYFINDING SIGNAGE ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 567890&? CLEARVIEW ADA CONDENSED REGULAR WAYFINDING SIGNAGE ABCDEFGHIJKLMNOPQRSTUVWXYZ 567890&? FORZA BOLD IDENTIFICATION SIGNAGE Paint: Matthews Paint (MP) Electrum MP0 R889, Satin Finish COLORS Paint: Matthews Paint (MP) Blue Abyss MP00 R50, Satin Finish Paint: Matthews Paint (MP) Brushed Aluminum SP, Satin Finish Matthews Paint (MP) Subtle Silver Metallic MP65, Satin Finish Paint: Verizon White Matthews Paint (MP) MP786 R506, Satin Finish. Opaque Vinyl: M Scotchcal Electrocut Opaque Graphic Film 775-0 (White) Opaque Vinyl: M Scotchcal Electrocut Opaque Graphic Film 775- (Black) Graphic Elements 5
Admissions Student Planning & Success Cashier / Student Accounts Stairs Restrooms Admissions Cashier / Student Accounts Testing Center & Exam Lab Rooms 0-9 Dean of Students Counseling & Wellness Disability Services Vice President of Student Services.A Wall Mounted Directional.D Ceiling Mounted Directional.E Ceiling Mounted Directional.F Ceiling Mounted Directional.F Ceiling Mounted Directional Sign Family 6
STUDENT PLANNING & SUCCESS BOOKSTORE STUDENT ACCOUNTS 5.A Blade Mounted Identification 7.C Ceiling Mounted Identification 7.D Wall Mounted Identification Sign Family 7
STUDENT HUB Scholarships Financial Aid Records CLAY PATHFINDER DIRECTORY Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming LEADERSHIP CENTER 0.A Ceiling Mounted Identification.A Elevator Directory.A Wall Mounted Identification Sign Family 8
.75" 0.75".A Plan SCALE: -/"= '-0" ' 8" 5".75" 5" 5" Dean of Students Vice President of Student Services 0.875".875".5".875" 0.9065".5" 0.565".5" 0.9065" Countersunk screws to be center aligned with panel.a Panel Detail SCALE: "= '-0" ' 8" /8" aluminum panel adhered to wall with VHB tape. 0.75" ' 9.75".75" 0.75".75" 0.75".75" 0.75".75" 0.75".75" 0.75".75" 0.75" " Rooms 0-9 Dean of Students Counseling & Wellness Disability Services Vice President of Student Services.A Front Elevation SCALE: -/"= '-0" /8" acrylic panel mechanically fastened to aluminum sheet with countersunk screws. Paint Electrum MP0, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). /8" acrylic panel mechanically fastened to aluminum sheet with countersunk screws. Paint Blue Abyss MP00, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). /8" x /" x /6" aluminum c-channels adhered to /8" aluminum panel. Paint Brushed Aluminum SP, satin finish. /8" aluminum panel painted Brushed Aluminum SP, satin finish. ' 6.75" 5.5" 5.5" 5.5" 5.5" 5.5" 5.5" /6" aluminum sheet adhered to /8" aluminum panel between c-channels. Paint Brushed Aluminum SP, satin finish. 5" 5" 5" 5" 5" 5" ".A Side Elevation SCALE: -/"= '-0" pg.0.a Wall Mounted Identification 9
/8" x /" x /6" aluminum c-channel. Rooms 0-9 Dean of Students Counseling & Wellness Disability Services Vice President of Student Services /8" acrylic panel. /8" aluminum panel. /6" aluminum sheet. C-Channel Detail SCALE: 6"= '-0".A Environmental Detail SCALE: /" = ' ' 0".A Wall Mounted Identification 0
.5" Rooms 0-7 Dean of Students Counseling & Wellness Disability Services The pin-up board is to be relocated to make room for the wayfinding sign. Faculty Offices ' 0".A Wall Mounted Identification
.5" Rooms 0-09 Dean of Students Counseling & Wellness This picture is currently located where indicated by the dotted line. Picture to be relocated. New location to be determined by LCCC. Disability Services Vice President of Student Services ' 0".A Wall Mounted Identification
6.65".5".875" 6".5".D Panel Detail SCALE: /"= '-0".5" ".5" Countersunk screws to be center aligned with panel " No less than 80" /8" x /" x /6" aluminum c-channel. /8" acrylic panel. /" aluminum panel. 0.75" /6" aluminum sheet. ' 0".D Plan SCALE: /"= '-0".D Environmental Detail SCALE: /" = ' C-Channel Detail SCALE: 6"= '-0" 0.75" 0.75".75" 6 5 6" ' 6" ' 0".D Front Elevation SCALE: /"= '-0" 8.5" Steel cable. Height may vary, field verify. /" aluminum panel painted Brushed Aluminum SP, satin finish. /8" acrylic panel mechanically fastened to aluminum sheet with countersunk screws. Paint Blue Abyss MP00, satin finish and Electrum MP0, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). /8" x /" x /6" aluminum c-channels adhered to /" aluminum panel. Paint Brushed Aluminum SP, satin finish. 6.75" 6.65" 6" 6 Specify attachment similar to this detail. /6" aluminum sheet adhered to /" aluminum panel 0.5" 0.5" between c-channels. Paint 0.5" Brushed Aluminum SP, satin finish. 0.75".D Side Elevation SCALE: /"= '-0".D Ceiling Mounted Directional
6.65".5".875" 6".5".E Panel Detail SCALE: /"= '-0".5" ".5" Countersunk screws to be center aligned with panel " Admissions No less than 80" /8" x /" x /6" aluminum c-channel. /8" acrylic panel. /" aluminum panel. 0.75" ' 0" /6" aluminum sheet..e Plan SCALE: /"= '-0".E Environmental Detail SCALE: /" = ' C-Channel Detail SCALE: 6"= '-0" 0.75" 0.75" 0.75".75" 6 6 5 Admissions 6" ' 6" ' 0".E Front Elevation SCALE: /"= '-0" '.5" Steel cable. Height may vary, field verify. /" aluminum panel painted Brushed Aluminum SP, satin finish. /8" acrylic panel mechanically fastened to aluminum sheet with countersunk screws. Paint Blue Abyss MP00, satin finish and Electrum MP0, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). /8" x /" x /6" aluminum c-channels adhered to /" aluminum panel. Paint Brushed Aluminum SP, satin finish. 6.75" 6.75" 6.65" 6.65" 6" 6" 6 Specify attachment similar to this detail. 0.5" 0.5" 0.5" 0.75".E Side Elevation SCALE: /"= '-0" /6" aluminum sheet adhered to /" aluminum panel between c-channels. Paint Brushed Aluminum SP, satin finish..e Ceiling Mounted Directional
.875" 6" " 6.65".5".5" ".5" Admissions Cashier / Student Accounts.5".F Panel Detail SCALE: /"= '-0" Countersunk screws to be center aligned with panel /8" x /" x /6" aluminum c-channel. /8" acrylic panel. 0.75" ' 0" No less than 80" /" aluminum panel..f Plan SCALE: /"= '-0" /6" aluminum sheet..f Environmental Detail SCALE: /" = ' C-Channel Detail SCALE: 6"= '-0" 0.75" 0.75" 0.75" 0.75".75" 6 6 6 5 Admissions Cashier / Student Accounts 6" ' 6" ' 0".F Front Elevation SCALE: /"= '-0" ' 0" Steel cable. Height may vary, field verify. /" aluminum panel painted Brushed Aluminum SP, satin finish. /8" acrylic panel mechanically fastened to aluminum sheet with countersunk screws. Paint Blue Abyss MP00, satin finish and Electrum MP0, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). /8" x /" x /6" aluminum c-channels adhered to /" aluminum panel. Paint Brushed Aluminum SP, satin finish. 6.75" 6.75" 6.75" 6.65" 6.65" 6.65" 6" 6" 6" 6 Specify attachment similar to this detail. 0.5" 0.5" 0.5" 0.75".F Side Elevation SCALE: /"= '-0" /6" aluminum sheet adhered to /" aluminum panel between c-channels. Paint Brushed Aluminum SP, satin finish..f Ceiling Mounted Directional 5
.875".875" 6" 6" 6.65".5".5".F Panel Detail SCALE: /"= '-0" Student Planning & Success Countersunk screws to be center aligned with panel.5" ".5" Stairs.5".5" /8" x /" x /6" aluminum c-channel. /8" acrylic panel. /" aluminum panel. 0.75".F Plan SCALE: /"= '-0" 6' 0" /6" aluminum sheet. C-Channel Detail SCALE: 6"= '-0" 0.75" 0.75" 0.75" 0.75".75" 6 6 6.F Front Elevation SCALE: /"= '-0" Student Planning & Success Cashier / Student Accounts Testing Center & Exam Lab Stairs Restrooms 6" 5' 0" 6" 6' 0" ' 0" Steel cable. Height may vary, field verify. /" aluminum panel painted Brushed Aluminum SP, satin finish. /8" acrylic panel mechanically fastened to aluminum sheet with countersunk screws. Paint Blue Abyss MP00, satin finish and Electrum MP0, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). /8" x /" x /6" aluminum c-channels adhered to /" aluminum panel. Paint Brushed Aluminum SP, satin finish. 6.75" 6.75" 6.75" 6.65" 6.65" 6.65" 6" 6" 6" Specify attachment similar to this detail. 0.5" 0.5" 0.5" 5 0.75" /6" aluminum sheet adhered to /" aluminum panel between c-channels. Paint Brushed Aluminum SP, satin finish..f Side Elevation SCALE: /"= '-0".F Ceiling Mounted Directional 6
Student Planning & Success Cashier / Student Accounts Testing Center & Exam Lab Stairs Restrooms.F Environmental Detail SCALE: /" = ' No less than 80".F Ceiling Mounted Directional 7
' 6" ' 6" 9" FACULTY OFFICES.5".5" 9" STUDENT PLANNING & SUCCESS.5".875".5".5" 5.A Panel Detail: Line SCALE: " = '.75" 5.A Panel Detail: Line.75" SCALE: " = ' '-9" /" " " '-6" 5.A Plan SCALE: " = ' /" aluminum panel painted Brushed Aluminum SP, satin finish. " x " x /8" aluminum angle painted Electrum MP0 (Yellow), satin finish. Mechanically fastened to /" aluminum panel with Aluminum Low Profile Binding Posts MMC# 9A5. Mechanically fasten to wall with countersunk screws. Paint screwheads Electrum MP0 (Yellow), satin finish. 0" STUDENT PLANNING 0" " '-8" 5.A Front Elevation SCALE: " = ' '-6" & SUCCESS /8" aluminum panel Blue Abyss MP00, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). Mount to /" aluminum panel with double sided tape and silicone. 9" 5 /" " " 5.A Side Elevation SCALE: " = ' 6 COUNSELING & CAMPUS WELLNESS 5.A Environmental Detail SCALE: /" = ' No less than 80" 5.A Blade Mounted Identification 8
7.C Panel Detail SCALE: " = ' BOOKSTORE.75".5".5" BOOKSTORE Sign to be offset as shown. 0.5" 6' 0" 7.C Plan SCALE: " = ' 7.C Sign Placement SCALE: NTS ' 5".75".75" ' 9" 0.75".5" 7.C Front Elevation SCALE: " = ' 5' 9" 6' 0" BOOKSTORE.5" ' 9.75" Steel cable. Height may vary, field verify. /8" x " aluminum bar adhered to aluminum panel painted Electrum MP0 (Yellow), satin finish. /" aluminum panel. Paint Brushed Aluminum SP, satin finish. /8" aluminum panel Blue Abyss MP00, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). Mount to /" aluminum panel with double sided tape and silicone. ' 9.75" ' 9".75".75" ' 5" 5 Specify attachment similar to this detail. 7.C Side Elevation SCALE: " = ' 7.C Ceiling Mounted Identification 9
STUDENT ACCOUNTS.5".5" Sign to be centered between windows as shown. STUDENT ACCOUNTS 7.D Panel Detail SCALE: " = '.75" 0.75" 6' 0" 7.D Plan SCALE: " = ' 7.D Sign Placement SCALE: NTS ' 5".75".75" ' 9" 0.75".5" 7.D Front Elevation SCALE: " = ' STUDENT ACCOUNTS 5' 9" 6' 0".5" ' 9.75" /8" x " aluminum bar adhered to aluminum panel painted Electrum MP0 (Yellow), satin finish. /" aluminum panel. Paint Brushed Aluminum SP, satin finish. /8" aluminum panel Blue Abyss MP00, satin finish. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775-0 (White). Mount to /" aluminum panel with double sided tape and silicone. ' 9.75" ' 9" Mount to wall with VHB tape..75".75" 5 ' 5" 7.D Side Elevation SCALE: " = ' 7.D Wall Mounted Identification 0
9' 0" Side A ' 5.5" Side D Side B ' " Side C Plan View SCALE: /"= '-0" 8' 0.5" Custom /" x /" x /8" aluminum square tube frame painted Brushed Aluminum SP, satin finish. Frame to be designed and engineered by fabricator to hold aluminum panels. 9' 0.5" '.5" 9' 0" " 6" 6" " ' " ' 0" ' 8" ' " ' 8" ' 0" ' " Side A Elevation SCALE: /"= '-0" Side C Elevation SCALE: /"= '-0" STUDENT HUB Scholarships Financial Aid Records 8' 0.5" /8" breakform sign panel mounted to aluminum panel with double sided tape and silicon. Paint face Blue Abyss MP00, satin finish and return Electrum MP0, satin finish. Letterforms to be /" water-jet cut acrylic and adhered to sign panel. Letterforms painted Verizon White MP786, satin finish. /8" aluminum sheet painted Electrum MP0, satin finish. Mount to aluminum panel with double sided tape and silicone. STUDENT HUB Scholarships Financial Aid Records 8' 0.5" 9' 0.5" 8' 0.75" 8' 0.5" 8' 0.65" ' 0" " /8" aluminum panel welded to aluminum frame. Paint Brushed Aluminum SP, satin finish. " ' 0" " 6" ' 8" 5 Side B Elevation SCALE: /"= '-0" /8" breakform sign panel mounted to aluminum panel with double sided tape and silicon. Paint face Electrum MP0, satin finish and return Blue Abyss MP00, satin finish. Letterform to be /" water-jet cut acrylic and adhered to sign panel. Letterforms painted Verizon White MP786, satin finish. ' " 6" ' 8" " " ' 0" 0.5" 9.5" ".5" '.65" '.5" ' 5.75" ' 5.5" ' 5.65" Side D Elevation SCALE: /"= '-0" ' 8.5" ' " 0.A Ceiling Mounted Identification
Sign Type 0.A desks. Location Detail SCALE: NTS 9'.75" Steel cable to attached sign frame and mechanically fastened to ceiling. Field verify height. '.65" 8' 0.5" Drop Ceiling.65" ' 8" ' 0.5" ' 8" ' 0.5" Breakform Sign Panel Detail SCALE: /"= '-0" Breakform Sign Panel Detail SCALE: /"= '-0" Bend Line. Bend Line. STUDENT HUB Scholarships Financial Aid Records 9' 8.5" ' 8.5" 8' 0.5" 5.5" STUDENT HUB Scholarships Financial Aid Records 5.5" 7.5".75".75".75".65" 7.5".75".75".75" Environmental Detail SCALE: /8" = ' STUDENT HUB Scholarships Financial Aid Records 9' 6" 0.A Ceiling Mounted Identification
Custom aluminum frame. Frame to be designed and engineered by fabricator to hold aluminum panels. /8" aluminum panels welded to aluminum frame. /8" aluminum sheets mounted to aluminum panel with double sided tape and silicone. 5 Assembly Detail SCALE: NTS /8" breakform sign panels mounted to aluminum panels with double sided tape and silicon. 0.A Ceiling Mounted Identification
0.75".5" ' 6.6875".A Plan SCALE: " = ' ' 9.975" ' 9.975" /" acrylic letterforms painted Verizon White MP786, satin finish. Flush mount to aluminum sheet. /8" aluminum sheet painted painted Subtle Silver Metallic MP65, satin finish and Blue Abyss MP00, satin finish and Electrum MP0, satin finish. " Systech AM Series Satin Natural Anodized finish adhered to aluminum sheet. Applied graphics, M Scotchcal Electrocut Opaque Graphic Film 775- (Black)..5" ' 6.6875" /6" ' 6.565" /6" DIRECTORY.5".A Front Elevation SCALE: " = ' CLAY PATHFINDER Admissions 0.6875" Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming ".5" '.875" 9.85".5" 6.65" ' 9.75" ' " /8" aluminum sheet adhered to wall with VHB tape. ' ".5" ".5" ' 9.75".A Side Elevation SCALE: " = ' DIRECTORY CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming.A Environmental Detail SCALE: /" = ' ' 7" 5' 8".A Elevator Directory
" " /6" " /6" DIRECTORY.5" /6".5".A Type Detail SCALE: " = ' CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming " " 0.6875" 0.65" 0.6875" " 0.6875" 0.65" 0.6875" /" 0.6875" /" " 0.6875" 0.65" 0.6875" Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming Assembly Detail SCALE: " = ' Systech AM Series adhered to aluminum sheet. DIRECTORY /8" aluminum panel. CLAY PATHFINDER DIRECTORY CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming.A Elevator Directory 5
Sign to be centered over existing drill holes from AED. CLAY PATHFINDER DIRECTORY Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Existing Site SCALE: NTS Existing AED to be removed and relocated. Placement Details SCALE: NTS Top of sign to line up with restroom sign. The directory sign will not line up with the restroom sign on the second floor. See next page. Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming ' 7" 5' 8".A Elevator Directory 6
Existing restroom sign was mounted at the incorrect height. Directory sign will not line up at the same height. This should only occur on the nd floor. Placement Details - nd Floor Only SCALE: NTS DIRECTORY CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming ' 7" 5' 8".A Elevator Directory 7
/8" breakform aluminum panel. Paint Blue Abyss MP00 and Electrum MP0 (Yellow), satin finish..a Plan SCALE: -/"= '-0" /" standoff pin mounts..a Aluminum Panel Detail SCALE: "= '-0" Break line..5" depth acrylic letterform flush mounted to aluminum panel with M VHB Tape. Paint Verizon White MP786. ' 0" /8" breakform aluminum panel. Paint Blue Abyss MP00 and Electrum MP0 (Yellow), satin finish. 0" 0" LEADERSHIP CENTER 0".5" ".5".75" 5.A Front Elevation SCALE: -/"= '-0" ' 0" LEADERSHIP CENTER.A Layout Detail SCALE: -/"= '-0".A Side Elevation SCALE: -/"= '-0".A Wall Mounted Identification 8
ST FLOOR Sign Location / Message Schedule
Ballroom.A-0 B A Ballroom 7.D-0 7.C-0 B A Coffee Shop.F-0 A B 0.A-0 A B D C.F-0 A A Cashier / Student Accounts.A-0 A Bookstore B A.A-0 A.F-0 Admissions A B 5.A-0 5.A-0 A B Student Planning & Success B A 5.A-0 A B Testing Center 5.A-0 Exam Lab These documents are intended to illustrate design intent and should only be used as a general guideline. All locations shown are approximate. All final locations are to be determined during Detailing and information contained on these pages shall not be reproduced, copied, or utilized except for the specific project for which they were created, without previous written authorization from Tangram Design, LLC. 07 by Tangram Design, LLC. College Clay Pathfinder Location Plan Pathfinder First Floor Signage Location Plan DATE: 08//7 0
SIGN # DESCRIPTION MESSAGE SIDE A NOTES.A-0 Wall Mounted Directional Student Planning & Success Admissions Book Store Leadership Center.F-0 Ceiling Mounted Directional Dean of Students Faculty Offices SIGN #.F-0.F-0 DESCRIPTION Ceiling Mounted Directional Ceiling Mounted Directional Vice President of Student Services MESSAGE SIDE A SIDE B Leadership Center Restrooms Restrooms Student Planning & Success Testing Center Elevator/Stairs Cashier/Student Accounts Exam Lab Bookstore Admissions Student Planning & Success Leadership Center Student Planning & Success Cashier / Student Accounts Coffee Shop Cashier/Student Accounts Testing Center & Exam Lab Leadership Center Stairs Restrooms NOTES First Floor Message Schedule
SIGN # DESCRIPTION SIDE A MESSAGE SIDE B NOTES 5.A-0 Blade Mounted Identification ADMISSIONS ADMISSIONS 5.A-0 Blade Mounted Identification STUDENT PLANNING & SUCCESS STUDENT PLANNING & SUCCESS 5.A-0 Blade Mounted Identification 5.A-0 Blade Mounted Identification TESTING CENTER EXAM LAB TESTING CENTER EXAM LAB First Floor Message Schedule
SIGN # DESCRIPTION SIDE A MESSAGE SIDE B NOTES 7.C-0 Ceiling Mounted Identification BOOKSTORE SIGN # 7.D-0 DESCRIPTION Wall Mounted Identification MESSAGE SIDE A NOTES STUDENT ACCOUNTS SIGN # 0.A-0 DESCRIPTION Ceiling Mounted Room Identification MESSAGE SIDE A SIDE B SIDE C SIDE D STUDENT HUB Scholarships Financial Aid Records STUDENT HUB Scholarships Financial Aid Records NOTES First Floor Message Schedule
SIGN # DESCRIPTION MESSAGE SIDE A NOTES.A-0 Elevator Directory DIRECTORY CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms SIGN #.A-0 DESCRIPTION Ceiling Mounted Identification SIDE A LEADERSHIP CENTER Extension Outreach School UW TRIO University of Wyoming MESSAGE SIDE B NOTES First Floor Message Schedule
ND FLOOR Sign Location / Message Schedule
Classroom.A-0 A Vice President for Student Services B A Classroom 5.A-05 5.A-06.F-0 Dean of Students A A B B A B 5.A-07 5.A-08 B A.A-0 A Faculty Offices.A-0 A.D-0 A B Faculty Offices These documents are intended to illustrate design intent and should only be used as a general guideline. All locations shown are approximate. All final locations are to be determined during Detailing and information contained on these pages shall not be reproduced, copied, or utilized except for the specific project for which they were created, without previous written authorization from Tangram Design, LLC. 07 by Tangram Design, LLC. College Clay Pathfinder Location Plan Pathfinder Second Floor Signage Location Plan DATE: 08//7 6
SIGN # DESCRIPTION MESSAGE SIDE A NOTES.A-0 Wall Mounted Directional Rooms 0-7 Dean of Students Counseling & Wellness Disability Services Faculty Offices.A-0 Wall Mounted Directional Rooms 0-09 Dean of Students Counseling & Wellness Disability Services Vice President of Student Services Second Floor Message Schedule 7
SIGN # DESCRIPTION SIDE A MESSAGE SIDE B NOTES.D-0 Ceiling Mounted Directional Faculty Offices 5-7 Faculty Offices 5-7.F-0 Ceiling Mounted Directional Faculty Offices 5-7 Faculty Offices 5-7 5.A-05 Blade Mounted Identification Student Planning & Success Admissions Rooms 08- Faculty Offices 0A-0F VICE PRESIDENT OF STUDENT SERVICES Vice President of Student Services Restrooms Admissions Student Planning & Success VICE PRESIDENT OF STUDENT SERVICES 5.A-06 Blade Mounted Identification 5.A-07 5.A-08 Blade Mounted Identification Blade Mounted Identification DEAN OF STUDENTS Counseling & Wellness Disability Services FACULTY OFFICES FACULTY OFFICES DEAN OF STUDENTS Counseling & Wellness Disability Services FACULTY OFFICES FACULTY OFFICES Second Floor Message Schedule 8
SIGN # DESCRIPTION MESSAGE SIDE A NOTES.A-0 Elevator Directory DIRECTORY CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming Second Floor Message Schedule 9
RD FLOOR Sign Location / Message Schedule
General Classroom Science Laboratory Classroom Science Laboratory Classroom Science Laboratory Classroom.A-0 A B.E-0 A.E-0 B Science Laboratory Classroom Science Laboratory Classroom Science Laboratory Classroom General Classroom These documents are intended to illustrate design intent and should only be used as a general guideline. All locations shown are approximate. All final locations are to be determined during Detailing and information contained on these pages shall not be reproduced, copied, or utilized except for the specific project for which they were created, without previous written authorization from Tangram Design, LLC. 07 by Tangram Design, LLC. College Clay Pathfinder Location Plan Pathfinder Third Floor Signage Location Plan DATE: 08//7
SIGN # DESCRIPTION SIDE A MESSAGE SIDE B NOTES.E-0 Ceiling Mounted Directional Rooms 0- Stairs.E-0 Ceiling Mounted Directional Science Laboratory Classrooms Stairs Rooms 0- Science Laboratory Classrooms SIGN #.A-0 DESCRIPTION Elevator Directory MESSAGE SIDE A NOTES CLAY PATHFINDER DIRECTORY Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming Third Floor Message Schedule
TH FLOOR Sign Location / Message Schedule
.A-0 A University of Wyoming A B.E-0 A B.E-0 A 5.A-09 B These documents are intended to illustrate design intent and should only be used as a general guideline. All locations shown are approximate. All final locations are to be determined during Detailing and information contained on these pages shall not be reproduced, copied, or utilized except for the specific project for which they were created, without previous written authorization from Tangram Design, LLC. 07 by Tangram Design, LLC. College Clay Pathfinder Location Plan Pathfinder Fourth Floor Signage Location Plan DATE: 08//7
SIGN # DESCRIPTION SIDE A MESSAGE SIDE B NOTES.E-0 Ceiling Mounted Directional Rooms 06- Stairs.E-0 Ceiling Mounted Directional Staff Offices -5 Staff Offices -5 Staff Offices -5 Stairs Rooms 0-8 5.A-09 Blade Mounted Identification STAFF OFFICES STAFF OFFICES Fourth Floor Message Schedule 5
SIGN # DESCRIPTION MESSAGE SIDE A NOTES.A-0 Elevator Directory DIRECTORY CLAY PATHFINDER Admissions Bookstore Cashier / Student Accounts Coffee Shop Exam Lab Leadership Center Student Planning & Success Testing Center Classrooms Counseling & Wellness Dean of Students Disability Services Faculty Offices Vice President of Student Services Science Laboratory Classrooms Extension Outreach School UW TRIO University of Wyoming Fourth Floor Message Schedule 6