88 580 69 Arts & Crafts Dining Buffet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Casual Attire For Today's Home Buffet Unit Part ist A. Top. Shelf 4 pcs. M. Rack N. Base P. eg O. eg Hardware ist Small Hex Wrench Hex Wrench 28 pcs. (+ extra) 8 pcs.(+ extra) Screw 8 pcs.(+ extra) Machine Screw Door 24 pcs. (+ extra) for Megnet Pull Handle 8 pcs. 8 pcs. (+ extra) (long) 6 pcs. (+ extra) 4 pcs. Adjustable Pin 6 pcs. (+2 extra) Drawer Pull Handle For assembly see instructions in carton 88 580 692 Tools required for assembly : Phillips screwdriver Home Styles Consumer Assistance ine 888-680-7460 and 877-83-039 servicedesk@homestyles-furniture.com
88 580 692 Arts & Crafts Dining Buffet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Casual Attire For Today's Home Part ist (in this carton) E. Middle Panel D. Middle Panel C. Side Panel B. Side Panel H. Back Stretcher F. Back Panel 3 pcs. G. Back Piece I. Front Piece J. Front Piece K. Fixed Shelf Q. Door R. Door S. Drawer (Knock-Down Construction, please refer to the last page of these instructions for steps to complete assembling drawers) Also need the following from carton 88 580 69 : Part ist in carton 88 580 69 Top (A) Shelf () Rack (M) Base (N) eg (O) eg (P) 4 2 pc. pcs. pc. pc. pcs. pcs. Hardware ist in carton 88 580 69 Hardware ist in carton 88 580 69 Screw for Adjustable Pin (long) 9 pcs. 9 pcs. 4 pcs. 9 pcs. 29 pcs. 8 pcs. 7 pcs. 25 pcs. Hex Wrench Door Pull Handle Drawer Pull Handle Machine Screw Small Hex Wrench Tools required for assembly : Phillips screwdriver Home Styles Consumer Assistance ine 888-680-7460 and 877-83-039 servicedesk@homestyles-furniture.com 8 pcs.
Assembly Instructions 2/5 IMPORTANT Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as you may need to tighten up the s in the future. STEP Screw Put Screws into the pre-drilled holes of Side Panel (B),(C), Middle Panel (D),(E) and tighten. B C Attach 2X s to Middle Panel (D) and (E) by using s in the pre-drilled holes (see Figure ). D E (Figure ) H B H F G F G F H STEP 2 Attach Back Stretcher (H) to Side Panel (B) with. Attach Back Piece (G) to Back Stretcher (H) then slide Back Panel (F) into place. Attach second Back Stretcher (H) to the unit with s.
Assembly Instructions 3/5 I STEP 3 K J D Attach Middle Panel (D) to the unit with s. E Attach Fixed Shelf (K), Front Piece (J) and Middle Panel (E) to the unit, using s and s. C Attach Front Piece (I) to the unit. Attach Side Panel (C) to the unit with s. N STEP 4 Attach Base (N) to the unit with s. O N STEP 5 P Attach eg (O) to Base (N) with s. Tighten up eg (P) in the pre-drilled hole of unit as shown. O
Assembly Instructions 4/5 STEP 6 M Attach Rack (M) to Top (A) with s.. A Machine Screw A (Figure 2) (Figure 3) Q STEP 7 Turn the unit back to its upright position. S R Place Top (A) onto the unit with s. S Slide Drawer (S) into place. Adjustable Pin Insert Adjustable Pins into both side panels and middle panels at the desired level. Slide Shelf () into place. Assemble Pull Handles to Door (Q) and (R) with Machine Screws.(see Figure 2) Attach Door (Q) and (R) to the side panels by sliding the door lift hinges into the side panel lift hinges. (see Figure 3) STEP 8 Insert s from the back and tighten.
Assembly Instructions 5/5 Drawer (S) STEP S Attach S to S3 and S4, using a Phillips screwdriver and long wood screws (4X), tighten halfway. S3 Attach S2 to S3 and S4 using long wood screws (4X), tighten halfway. (see Figure ) S4 S2 Figure STEP 2 MAKE SURE ROER IS ON THE BACK S Slide S5 into the grooves in S3 and S4. Be sure to push S5 all the way forward to it meets S. (see Figure 2) S3 Figure 2 S4 S5 S3 S S5 S2 Figure 3 S2 STEP 4 S4 Attach hardware pulls with machine screws. (see Figure 4) STEP 3 Insert short wood screws (6X) into the pre-drilled holes in S5, tighten screws. (see Figure 3) Figure 4 Tighten all screws used in drawer assembly. Part ist S. Front Part S2. Back Part S3. Side Part S4. Side Part S5. Base Part