9 Compact Photoeectric Reated Information CX- SERIES Ver. Genera terms and conditions... F-7 seection guide... P.8~ MS-AJ / CHX-SC...P.99 / P.9 Gossary of terms / Genera precautions... P.59~ / P.5 Korea s S-mark... P. PHOTOEECTRIC PHOTOEECTRIC Ver. Conforming to EMC Directive Recognition IGHT Certified (Some modes ony) FOW PARTICUAR SIMPE MEASURE CONTRO PNP output type avaiabe ight intensity monitor Interference prevention s that are environmentay and user friendy. PC / TERMINAS VISUAIZATION separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Reducing environmenta burdens further Up to 6% ess power consumption The tota ineup of 8 modes covers through the incusion of a newy deveoped custom integrated circuit.the CX- series achieves reductions in power consumption of up to 6%, averaging % reduction when upgrading due to its unique design. These sensors reduce carbon emissions and contribute to environmenta friendiness. Previous CX-8 5 ma Providing stabe detection with ow power consumption Incudes an anaog CMOS processor ASIC New CX-8 ma Upgrade for up to 6% reduction Contributing to reduced carbon dioxide emissions Eectricity consumed by the CX- series has been reduced on average.5 ma. Cacuating 8 hours/day, 6 days (operating 5 days/week) for a tota of,8 hours/year eads to: The CX- contributes Approx. 8.6 t annuay in carbon dioxide reductions to the word Strong against oi and cooant iquids CX- / /9 The ens materia for the thru-beam type, retrorefective type (excuding the CX-8 ) and the diffuse refective type are made of a strong acryic that resists the harmfu effects of cooants. These sensors can be used with confidence even around meta processing machinery that disperses oi mists. The protection mechanism aso conforms to IP67 (IEC). Test Oi JIS Standard Product Name ubricant - Veocity Oi No. Water-insoube -5 Daphnecut AS-D cutting oi - Yushiron Oi No.ac (Note) Water-soube W- Yushiron ubic HWC68 (Note) cutting oi W- Yushiroken S5N (Note), hours; Immersion (depth m); Insuation resistance MΩ/5 V Note: Yushiron and Yushiroken are registered trademarks of Yushiro Chemica Industry Co., td. Strong against ethano A strong, ethano resistant poycarbonate was used for the front and dispay covers. Safe even for instaing near food processing machinery that disperses ethano based detergents. The protection mechanism aso conforms to IP67 (IEC). CX- /8 Caution: Set the CX-8 so that ceaning iquid wi not get on to the attached refector.
Compact Photoeectric CX- SERIES Ver. 9 APPICATIONS Detecting out of position tape feeder cassette Sit mask Out of position CX- Detecting objects in paces that have a ot of dust or couds of partices CX- Passage confirmation of object on a conveyor bet Detecting transparent gass bottes Sma tabet sensing Biscuit sensing CX- CX-9 CX- PHOTOEECTRIC PHOTOEECTRIC IGHT FOW PARTICUAR SIMPE MEASURE CX-8 CONTRO BASIC PERFORMANCE Strong infrared beam CX-/ Remarkabe penetrating power enabes appications such as package content detection. Can sense differences as sma as. mm.6 in, with hysteresis of % or ess CX-/ An advanced optica system provides sensing performance that is.5 times approx. than conventiona modes. Even utra-sma differences of. mm.6 in can be detected accuratey..5 times the sensing capabiity! PC / TERMINAS VISUAIZATION Note: When sensing utiizing penetrating power, make sure to verify using the actua sensor. Hardy affected by coors % higher sensing capabiity CX-/ Both back and white objects can be sensed at the same distances. No adjuster contro is needed, even when products of different coors are moving aong the production ine. The difference in sensing ranges is % or ess between non-gossy white with a setting distance of 5 mm.969 in and non-gossy gray with a brightness eve of 5. Height differences of as itte as. mm.6 in can be detected at a setting distance of mm.787 in Retrorefective type with poarizing fiters CX-9 poarizing fiters ensure stabe sensing even on a specuar object. CX-9 separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6
9 Compact Photoeectric CX- SERIES Ver. PHOTOEECTRIC PHOTOEECTRIC IGHT FOW PARTICUAR SIMPE MEASURE CONTRO PC / TERMINAS BASIC PERFORMANCE Introducing the transparent object sensing type sensor Our unique optica system and transparent object sensing circuitry provide stabe sensing of even thinner transparent objects than the conventiona modes. Twice the sensing range! CX-8 ong sensing range of 5 m 6. ft A ong 5 m 6. ft sensing range is possibe with the red ED type that is easy to aign with the beam axis. Can be used for wide automatic door shutters. CX-9 CX-8 Transparent objects detectabe with CX-8 (Typica exampes) object object size (mm in) Gass sheet Cyindrica gass Acryic board Styro (Foppy case) Food wrapping fim Cigarette case fim Viny sack PET botte (5m) 5 5.969.969 ø5 ø.969 = 5.969 5 5.969.969 5 5.969.969 5 5.969.969 5 5.969.969 5 5.969.969 ø66 ø.598 t =.7.8 t =..5 t =..9 t =.9.5 t = µm.9 mi t = µm.787 mi t = µm.8 mi Refector setting range CX-8: to 5 mm.8 to 9.685 in, CX-8: to m.8 to 6.56 ft [with the RF- refector at the optimum condition (Note)] Each object shoud pass across the beam at the center between the sensor and the refector. : ength of cyindrica gasses t: Thickness of sensing object Note: The optimum condition is defined as the condition in which the sensitivity eve is set such that the stabiity indicator just ights up when the object is absent. Utra-ong sensing range of m 98. ft CX- The CX- achieves the utra-ong sensing range of m 98. ft. It can be used for a stacker crane or a mutieve parking structure. VISUAIZATION separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 ENVIRONA RESISTANCE Strong on dust and dirt Because the ight source is an infrared ight, it is strong on dust and dirt compared to the red beam type. Strong even in cod environments Stabe performance can be maintained even in environments of 5 C F. ECO CX-/ Thoroughy eiminating unnecessary waste, Reducing many environmenta burdens The CX- series have three different cabe ength types and uses very simpe packaging to reduce waste. The bag is made of poyethyene and does not emit toxic gasses. Stronger noise resistance The CX- has a high noise resistance then its previons mode. By incorporating an inverter countermeasure circuit that appropriatey shifts with peak waveength, the sensor now resists high-frequency noise from high-votage inverter motors and inverter ights more effectivey. Fuorescent ight tube Inverter motor
Compact Photoeectric CX- SERIES Ver. 9 MOUNTING Beam axis aignment made easy with a high uminance spot beam These sensors have a high uminance red ED spot beam which provides bright visibiity enabing the sensing position to be checked at a gance. Because it achieved sma beam spot approx. ø mm ø.79 in at setting distance mm.97 in, approx. ø5 mm ø.97 in at setting distance mm 7.87 in, even the minutest object can be accuratey detected. OPERABIITY CX- CX- Great visibiity approx. ø mm ø.79 in high uminance spot beam (at setting distance mm.97 in) Reduction of voume adjustment abor CX- Because these sensors possess many variations depending on the sensing range, enabes you to make optima voume adjustment easiy. CX-: 8 mm.96 in CX-: mm.8 in CX-: mm.97 in Narrow-view type CX-: 7 to mm.756 to.8 in The bright spot makes beam axis aignment easy These sensors have a high uminance red spot that provides bright visibiity. The sensing position can be checked at a gance. Because the CX- sensor has the smaest spot in its cass ø mm ø.79 in approx., even the minutest object can be accuratey detected. Can be used for sensing minute differences CX- Great visibiity approx. ø mm ø.79 in high uminance spot CX- CX- Equipped with a 5-turn adjuster so that even chaenging range settings can be handed with ease. PHOTOEECTRIC PHOTOEECTRIC IGHT FOW PARTICUAR SIMPE MEASURE CONTRO PC / TERMINAS VISUAIZATION VARIETIES Basic type new reease Omit the sensitivity adjuster and operation mode switch and reease a basic type cabe.5 m.6 ft in ength. If the usage is cear, quick construction can be performed onsite without detaied adjustments and the cost can be controed. ess processing M8 pug-in connector type and M pigtaied type are avaiabe. This contributes to ess time spent in setting up. In addition, cabe types are avaiabe with cabe engths of.5 m.6 ft, m 6.56 ft and 5 m 6. ft. This resuts in ess wastage. No unnecessary cabes or termina bocks.5 m.6 ft Cabe type m 6.56 ft 5 m 6. ft Great maintainabiity M8 pug-in connector type M pigtaied type Ebow Straight Straight m 6.56 ft / 5 m 6. ft m 6.56 ft / ( 5 m 6. ft ) Seect from spot diameters as per the appication CX-/ Within the choice of 5 mm.969 in sensing range sensors, we offer sma spot approx. ø mm ø.79 in type optima for detecting minute object and arge approx. ø6.5 mm ø.56 in spot type capabe of sensing object covered with hoes and grooves. CX- Spot diameter: ø mm ø.79 in approx. [Positioning] Detects minute hoes. CX- Spot diameter: ø6.5 mm ø.56 in approx. Detection of presence / absence of objects Ignores minute hoes and accuratey detects objects. ( m 5 m 6.56 ft 6. ft / ) Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6
95 Compact Photoeectric CX- SERIES Ver. PHOTOEECTRIC PHOTOEECTRIC IGHT FOW PARTICUAR FUNCTIONS BGS / FGS functions make even the most chaenging settings possibe! For detais on the operation of the BGS / FGS functions, refer to BGS / FGS functions of PRECAUTIONS FOR PROPER. The BGS function is best suited for the foowing case Background not present When object and background are separated BGS Not affected if the background coor changes or someone passes behind the conveyor. CX- The FGS function is best suited for the foowing case Background present When object and background are cose together FGS When the object is gossy or uneven Unaffected by goss, coor or uneven surfaces when sensing objects present on a conveyor bet. SIMPE MEASURE CONTRO PC / TERMINAS VISUAIZATION separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 BGS (Background suppression) function The sensor judges that an object is present when ight is received at position A of the ight-receiving eement (-segment eement). This is usefu if the object and background are far apart. The distance adjustment method is the same as the conventiona adjustment method for adjustabe range refective type sensors. Background OFF ight received at eement B, or ight not received Moving object Object in the back Setting distance Strong against interference ON (ight received at eement A) Eement A Eement B The interference prevention function ets two sensors to be mounted cose together precisey. Interference prevention fiter (Optiona) Thru-beam type Ony CX- Retrorefective type Diffuse refective type Adjustabe range refective type Automatic interference prevention function Caution: Pease use the FGS function together with a conveyor or other background unit. FGS (Foreground suppression) function The sensor judges that an object is present when no ight is received at position B of the ight-receiving eement (- segment eement). Accordingy, even objects that are gossy can be sensed. This is usefu if the object and background are cose together, or if the object being sensed is gossy. OFF in this condition ony A B Object absent OFF ens Emitting eement ight received at position B A conveyor or other back-ground must be present ON in a other conditions Object present ON ight received at position A For gossy object ON Conveyor Conveyor Conveyor Setting distance ight is not received at position B, so a object is judged to be present Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. 96 ORDER GUIDE Standard type Thru-beam Type Appearance range ong sensing range Mode No. (Note ) NPN output PNP output m.88 ft CX- CX--P 5 m 9. ft CX- CX--P m 98.5 ft CX- CX--P Output operation Emitting eement Red ED Infrared ED EECTRIC EECTRIC IGHT FOW Retrorefective With poarizing fiters ong sensing range For transparent object sensing m 9.8 ft (Note ) CX-9 CX-9-P 5 m 6. ft (Note ) CX-9 CX-9-P 5 to 5 mm.969 to 9.685 in (Note ) CX-8 CX-8-P 5 to,mm.969 to 9.7 in (Note ) CX-8 CX-8-P. to m.8 to 6.56 ft (Note ) CX-8 CX-8-P Switchabe either ight-on or Dark-ON Red ED Infrared ED PARTICUAR SIMPE mm.97 in CX- CX--P CONTRO Diffuse refective Adjustabe range refective Narrowview Sma spot mm.8 in CX- CX--P 8 mm.96 in CX- CX--P Infrared ED 7 to mm.756 to.8 in CX- CX--P Red ED to 5 mm.79 to.969 in CX- CX- CX--P CX--P 5 to mm.59 to.97 in CX- CX--P to mm.787 to.8 in CX- CX--P Switchabe either Detection-ON or Detection-OFF Red ED PC / TERMINAS VISUAIZATION NOTE: Mounting bracket is not suppied with the sensor. Pease seect from the range of optiona sensor mounting brackets. Notes: ) The mode No. with E shown on the abe affixed to the thru-beam type sensor is the emitter, D shown on the abe is the receiver. (e.g.) of CX-: CX-E, of CX-: CX-D ) The sensing range of the retrorefective type sensor is specified for the RF- refector. The sensing range represents the actua sensing range of the sensor. The sensing ranges itemized in A of the tabe beow may vary depending on the shape of sensing object. Be sure to check the operation with the actua sensing object. separated range: A object Setting range of the refector: B Refector A B CX-9 CX-9 CX-8 CX-8 CX-8 to m to 9.8 ft to 5 m 5 to 5 mm 5 to, mm. to m to 6. ft.969 to 9.685 in.969 to 9.7 in.8 to 6.56 ft. to m. to 5 m to 5 mm to, mm.8 to m.8 to 9.8 ft.8 to 6. ft.97 to 9.685 in.97 to 9.7 in.65 to 6.56 ft CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
97 Compact Photoeectric CX- SERIES Ver. EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE Thru-beam Retrorefective ORDER GUIDE NEW Basic type (Without operation mode switch and sensitivity adjuster. Cabe is.5 m. in ong) Type Appearance range ong sensing range With poarizing fiters Optiona (Note ) m.88 ft 5 m 9. ft m 9.8 ft (Note ) Mode No.(Note ) NPN output PNP output Output operation CX-A-C5 CX-A-P-C5 ight-on CX-B-C5 CX-B-P-C5 Dark-ON CX-A-C5 CX-A-P-C5 ight-on CX-B-C5 CX-B-P-C5 Dark-ON CX-9A-C5-Y CX-9A-P-C5-Y ight-on CX-9B-C5-Y CX-9B-P-C5-Y Dark-ON Emitting eement Red ED Infrared ED Red ED CONTRO NOTE: Mounting bracket is not suppied with the sensor. Pease seect from the range of optiona sensor mounting brackets. Notes: ) The mode No. with E shown on the abe affixed to the thru-beam type sensor is the emitter, D shown on the abe is the receiver. (e.g.) of CX-A-C5: CX-E, of CX-A-C5: CX-AD ) The refector is sod separatey. ) The sensing range of the retrorefective type sensor is specified for the RF- (optiona) refector. The sensing range represents the actua sensing range of the sensor. The sensing ranges itemized in A of the tabe beow may vary depending on the shape of sensing object. Be sure to check the operation with the actua sensing object. PC / TERMINAS VISUAIZATION range: A object Setting range of the refector: B Refector (Optiona) A B CX-9 to m to 9.8 ft. to m.8 to 9.8 ft separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. 98 ORDER GUIDE.5 m.6 ft / 5 m 6. ft cabe ength types.5 m.6 ft / 5 m 6. ft cabe ength types (standard: m 6.56 ft, basic:.5 m.6 ft) are aso avaiabe. When ordering this type, suffix -C5 for the.5 m.6 ft cabe ength type, -C5 for the 5 m 6. ft cabe ength type to the mode No. (Excuding CX- and basic type) (e.g.).5 m.6 ft cabe ength type of CX--P is CX--P-C5 5 m 6. ft cabe ength type of CX--P is CX--P-C5 EECTRIC EECTRIC M8 pug-in connector type, M pigtaied type M8 pug-in connector type and M pigtaied type are aso avaiabe. When ordering this type, suffix -Z for the M8 connector type, -J for the M pigtaied type to the mode No. (Pease note that M pigtaied type is not avaiabe for CX-. Excuding basic type) (e.g.) M8 connector type of CX--P is CX--P-Z M pigtaied type of CX--P is CX--P-J IGHT FOW PARTICUAR Mating cabe ( cabes are required for the thru-beam type.) For M8 pug-in connector type For M pigtaied type Type Mode No. Cabe ength Description Straight Ebow -core -core Package without refector NPN output type: CX-9-Y PNP output type: CX-9-P-Y CN-A-C CN-A-C5 CN-A-C CN-A-C5 CN--C CN--C5 CN--C CN--C5 m 6.56 ft 5 m 6. ft m 6.56 ft 5 m 6. ft m 6.56 ft 5 m 6. ft m 6.56 ft 5 m 6. ft Can be used with a modes For thru-beam type emitter (-core) Can be used with a modes Mating cabe CN-A-C CN-A-C5 ø9 mm ø.5 in. mm.6 in ø mm ø.57 in CN--C, CN--C5 CN--C, CN--C5 CN-A-C CN-A-C5. mm.99 in.5 mm.87 in ø9 mm ø.5 in ø mm ø.57 in SIMPE CONTRO PC / TERMINAS VISUAIZATION Accessory RF- (Refector) mm.8 in ø mm ø.55 in ø5 mm ø.97 in separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
99 Compact Photoeectric CX- SERIES Ver. separated EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Designation Round sit mask For thrubeam type sensor ony Rectanguar sit mask For thrubeam type sensor ony Mode No. range Min. sensing object Sit size Sit mask Sit on one side Sit on both sides Sit on one side Sit on both sides CX- mm 5.78 in mm.787 in ø.5 mm OS-CX-5 CX- ø. in 6 mm.6 in mm.8 in ø mm ø.7 in ø.5 mm ø. in CX-, mm 7. in 6 mm.6 in CX- 9 mm 5. in mm.97 in ø mm ø.9 in ø mm OS-CX- CX- ø.9 in.5 m.9 ft 5 mm 5.96 in ø mm ø.7 in CX-.7 m 8.857 ft mm.8 in ø.5 mm ø.59 in CX- m 6.56 ft mm 5.78 in ø mm ø.79 in ø mm OS-CX- CX- ø.79 in m 9.8 ft 6 mm.6 in ø mm ø.7 in CX- 6 m 9.685 ft, mm 7. in ø mm ø.8 in CX- m 6.56 ft mm 5.78 in.5 6 mm.5 6 mm OS-CX-5 6 CX- m 9.8 ft 6 mm.6 in ø mm ø.7 in..6 in..6 in CX- 6 m 9.685 ft, mm 7. in CX- m 9.8 ft m.8 ft 6 mm 6 mm OS-CX- 6 CX-.5 m.76 ft.5 m.9 ft ø mm ø.7 in.9.6 in.9.6 in CX- 9 m 9.58 ft m 9.8 ft CX- 5 m 6. ft m 6.56 ft 6 mm 6 mm OS-CX- 6 CX- 7.5 m.66 ft m 9.8 ft ø mm ø.7 in.79.6 in.79.6 in CX- 5 m 9. ft 6 m 9.685 ft Designation Mode No. range Min. sensing object Interference prevention fiter For CX- ony Refector For retro- refective type sensor ony PF-CX-V (Vertica, Siver) pcs. per set PF-CX-H (Horizonta, ight brown) pcs. per set 5 m 6. ft (Note ) ø mm ø.7 in (Note ) CX-9 m.8 ft (Note ) CX-9.5 m.9 ft (Note ) RF- CX-8 ø mm ø.8 in CX-8. to. m.8 to.98 ft (Note ) CX-8. to.6 m.8 to.969 ft (Note ) CX-9.5 m.9 ft (Note ) CX-9 m 9.8 ft (Note ) RF- CX-8 5 to mm.969 to.8 in (Note ) ø5 mm ø.78 in CX-8. to.7 m.8 to.97 ft (Note ) CX-8. to. m.8 to.65 ft (Note ) RF-(Note ) CX-9 -Y m 9.8 ft (Note ) ø5 mm ø.969 in Notes: ) Vaue when attached on both sides. ) Set the distance between the CX-9 /9 and the refector to. m.8 ft or more. However, see the tabe beow for CX-8. The sensing range A may vary depending on the shape of sensing object. Be sure to check the operation with the actua sensing object. range: A object Setting range of the refector: B Refector Mode No. Refector A B CX-8 RF- 5 to mm.969 to.8 in to mm.97 to.8 in RF-. to.7 m.8 to.97 ft. to.7 m.656 to.97 ft CX-8 RF-. to. m.8 to.98 ft. to. m.8 to.98 ft RF-.5 to m.6 to.8 ft. to m.8 to.8 ft CX-8 RF-. to. m.8 to.65 ft.5 to. m.6 to.65 ft RF-. to.6 m.8 to.969 ft. to.6 m.98 to.969 ft Refector RF-.8 mm.5 in ) RF- is attached to the retrorefective type sensor other than the basic type.. mm. in mm. in Round sit mask OS-CX- Fitted on the front face of the sensor with onetouch. Rectanguar sit mask OS-CX- 6 Fitted on the front face of the sensor with onetouch. Interference prevention fiter PF-CX-V (Vertica, Siver) PF-CX-H (Horizonta, ight brown) Two sets of CX- can be mounted cose together. RF-. mm.665 in 5. mm.9 in 8. mm.7 in RF- 59. mm.5 in Round sit mask (Stainess stee) Rectanguar sit mask (Stainess stee) Interference prevention fiter 5. mm.98 in 8. mm.7 in Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. Designation Mode No. MS-RF- Refector mounting bracket range (Note ):.7 m.97 ft [CX-9 ]. m.97 ft [CX-9 ]. to.6 m.8 to.969 ft [CX-8 ] RF- range (Note 5): RF-.5 m.6 ft [CX-9 ] Ambient temperature: -5 to +5 C - to + F Ambient humidity: 5 to 85 % RH Notes: ) Keep the tape free from stress. If it is pressed too much, its capabiity may deteriorate. ) Do not cut the tape. It wi deteriorate the sensing performance. Ambient temperature: -5 to +55 C - to + F Ambient humidity: 5 to 85 % RH Foot anged mounting bracket It can aso be used for mounting RF-. MS-CX- checker (Note ) MS-CX- MS-CX-5 Back bianged mounting bracket MS-CX- Back anged mounting bracket MS-AJ Horizonta mounting type MS-AJ Vertica mounting type MS-AJ-A Horizonta mounting type MS-AJ-A Vertica mounting type MS-AJ-M Horizonta mounting type MS-AJ-M Vertica mounting type CHX-SC It is usefu for beam aignment of thru-beam type sensors. The optimum receiver position is given by indicators, as we as an audio signa. Basic assemby 5 Assemby for refector MS-AJ-A 5 Eevation ange: ±5 Height adjustment: 5 mm 5.96 in approx. Mounting hoe for M6 screw MS-AJ 5 5 Eevation ange: ±5 With the atera arm, the sensor can sense from above a production ine. Height adjustment: 5 mm 5.96 in approx. Mounting hoe for M6 screw Swive: 6 rotation Forward / back adjustment: mm 5.8 in approx. Height adjustment: 5 mm 5.96 in approx. 5 Eevation ange: ±5 6 rotation 5 5 Ange adjustment: ±5 With the atera arm, the sensor can sense from above a production ine. Forward / back adjustment: mm 5.8 in approx. 6 rotation Refective tape mm.8 in SIMPE RF-.7 mm.8 in 8 mm.5 in mm.8 in.7 mm.8 in 5 mm.98 in CONTRO.5 mm. in mm.8 in mm.8 in PC / TERMINAS mounting bracket MS-CX- MS-CX- 5 5 Mounting Ange adjustment: ±5 hoe for M6 screw VISUAIZATION Two M (ength mm.7 in) screws with washers are attached. Two M (ength mm.7 in) screws with washers are attached. MS-CX- MS-CX-5 Height adjustment: 5 mm 5.96 in approx. Two M (ength mm.55 in) screws with washers are attached. Two M (ength mm.7 in) screws with washers are attached. MS-CX- separated CX- EX- EX- EX- EX- MS-AJ-M Swive: 6 rotation Height adjustment: 5 mm 5.96 in approx. MEASURE Mounting hoe for M6 screw Mounting hoe for M6 screw FOW PARTICUAR Two M (ength mm.9 in) screws with washers are attached. Swive: 6 rotation 5 IGHT MS-AJ-M MS-AJ-A Swive: 6 rotation MS-RF atera arm assemby Universa sensor mounting stand Two M (ength 8 mm.5 in) screws with washers are attached. RF- Notes: ) The pug-in connector type sensor does not aow use of some sensor mounting brackets because of the protrusion of the connector. ) Refer to the universa sensor mounting stand MS-AJ series pages. ) Refer to the sensor checker CHX-SC pages. ) Set the distance between the sensor and the refective tape to. m.8 ft (CX-8 :. m. ft) or more. 5) Set the distance between the sensor and the refective tape to. m.656 ft or more. Swive: 6 rotation Two M (ength mm.7 in) screws with washers are attached. RF- Foot bianged mounting bracket It can aso be used for mounting RF-. The thru-beam type sensor needs two brackets. Protective mounting bracket MS-CX- MS-AJ PHOTOEECTRIC PHOTOEECTRIC For RF- range (Note ):.5 m.6 ft [CX-9 ].8 m.65 ft [CX-9 ] RF- Universa sensor mounting stand (Note ) MS-RF For RF- MS-RF mounting bracket (Note ) MS-RF- Protective mounting bracket for RF- It protects the refector from damage and maintains aignment. MS-RF Refective tape Refector mounting bracket Description Swive: 6 rotation 5 5 Eevation ange: ±5 Height adjustment: 5 mm 5.96 in approx. CX- Two M (ength mm.7 in) screws with washers are attached. EQ- EQ-5 checker CHX-SC -S PO W ER Mounting hoe for M6 screw C H E VE X- SC RT-6 checker Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. separated EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 SPECIFICATIONS Standard type Type Thru-beam Retrorefective Diffuse refective ong sensing range With poarizing fiters ong sensing range For transparent object sensing Narrow-view NPN output CX- CX- CX- CX-9 CX-9 CX-8 CX-8 CX-8 CX- CX- CX- CX- Item PNP output CX--P CX--P CX--P CX-9-P CX-9-P CX-8-P CX-8-P CX-8-P CX--P CX--P CX--P CX--P Mode No. range object m.88 ft 5 m 9. ft m 98.5 ft ø mm ø.7 in or more opaque object (Note ) m 9.8 ft (Note ) ø5 mm ø.969 in or more opaque, transucent or specuar object (Note, 5) 5 m 6. ft (Note ) ø5 mm ø.969 in or more opaque or transucent object (Note, 5) 5 to 5 mm.969 to 9.685 in (Note ) 5 to, mm.969 to 9.7 in (Note ). to m.8 to 6.56 ft (Note ) ø5 mm ø.969 in or more transparent, transucent or opaque object (Note, 5) mm.97 in (Note ) mm.8 in (Note ) 8 mm.96 in (Note ) Opaque, transucent or transparent object (Note 5) 7 to mm.756 to.8 in (Note ) Opaque, transucent or transparent object (Note 5) Min. sensing object: ø.5 mm ( ø. in copper wire ) Hysteresis 5 % or ess of operation distance (Note ) Repeatabiity (perpendicuar to sensing axis).5 mm. in or ess mm.9 in or ess.5 mm. in or ess Suppy votage to V DC ± % Rippe P-P % or ess Current consumption Output : 5 ma or ess : ma or ess : 5 ma or ess : ma or ess : ma or ess : ma or ess ma or ess <NPN output type> NPN open-coector transistor Maximum sink current: ma Appied votage: V DC or ess (between output and V) Residua votage: V or ess (at ma sink current) V or ess (at 6 ma sink current) ma or ess ma or ess 5 ma or ess <PNP output type> PNP open-coector transistor Maximum source current: ma Appied votage: V DC or ess (between output and +V) Residua votage: V or ess (at ma source current) V or ess (at 6 ma source current) Output operation Switchabe either ight-on or Dark-ON Short-circuit protection Incorporated Response time ms or ess ms or ess ms or ess Operation indicator Orange ED (ights up when the output is ON)(incorporated on the receiver for thru-beam type) Stabiity indicator Green ED (ights up under stabe ight received condition or stabe dark condition)(incorporated on the receiver for thru-beam type) Green ED (ights up when the Power indicator power is ON) (incorporated on the emitter) Sensitivity adjuster Continuousy variabe adjuster (incorporated on the receiver for thru-beam type) Automatic interference prevention function Environmenta resistance Protection Two units of sensors can be mounted cose together with interference prevention fiters. ( range: 5 m 6. ft) Incorporated (Two units of sensors can be mounted cose together.) IP67 (IEC) Ambient temperature -5 to +55 C - to + F (No dew condensation or icing aowed), Storage: - to +7 C - to +58 F Ambient humidity Ambient iuminance Votage withstandabiity Insuation resistance Vibration resistance Shock resistance 5 to 85 % RH, Storage: 5 to 85 % RH Incandescent ight:, x at the ight-receiving face, V AC for one min. between a suppy terminas connected together and encosure MΩ, or more, with 5 V DC megger between a suppy terminas connected together and encosure to 5 Hz frequency,.5 mm.59 in doube ampitude ( G max.) in X, Y and Z s for two hours each 5 m/s acceeration (5 G approx.) in X, Y and Z s for three times each Emitting eement (moduated) Red ED Infrared ED Red ED Infrared ED Infrared ED Red ED Materia Cabe Peak emission waveength 68 nm.7 mi 87 nm. mi 85 nm. mi 68 nm.7 mi 65 nm.6 mi 87 nm. mi 86 nm. mi 65 nm.5 mi Cabe extension Weight Encosure: PBT (Poybutyene terephthaate), ens: Acryic (CX-8 : Poycarbonate), Indicator cover: Acryic (CX-8 : Poycarbonate). mm -core (thru-beam type emitter: -core) cabtyre cabe, m 6.56 ft ong Extension up to tota m 8.8 ft is possibe with. mm, or more, cabe (thru-beam type: both emitter and receiver) Net : 5 g approx., : 5 g approx. 5 g approx. Gross g approx. 8 g approx. 6 g approx. Accessories RF- (Refector): pc. Notes: ) Where measurement conditions have not been specified precisey, the conditions used were an ambient temperature of + C +7. F. ) The sensing range and the sensing object of the retrorefective type sensor are specified for the RF- refector. The sensing range represents the actua sensing range of the sensor. The sensing ranges itemized in A of the tabe beow may vary depending on the shape of sensing object. Be sure to check the operation with the actua sensing object. CX-9 CX-9 CX-8 CX-8 CX-8 range: A object Setting range of the refector: B Refector A B to m to 9.8 ft. to m.8 to 9.8 ft to 5 m to 6. ft. to 5 m.8 to 6. ft 5 to 5 mm.969 to 9.685 in to 5 mm.97 to 9.685 in 5 to, mm.969 to 9.7 in to, mm.97 to 9.7 in. to m.8 to 6.56 ft.8 to m.65 to 6.56 ft ) The sensing range and hysteresis of the diffuse refective type sensor are specified for white non-gossy ( mm 7.87 7.87 in) as the object. ) If sit masks (optiona) are fitted, an object of ø.5 mm ø. in (using round sit mask) can be detected. 5) Make sure to confirm detection with an actua sensor before use. Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. Type Sma spot Adjustabe range refective NPN output CX- CX- CX- CX- Item PNP output CX--P CX--P CX--P CX--P Adjustabe range (Note ) to 5 mm.787 to.969 in to mm.787 to.97 in to mm.575 to.8 in range (with white non-gossy ) to 5 mm.79 to.969 in 5 to mm.59 to.97 in to mm.787 to.8 in Mode No. Hysteresis (with white non-gossy ) Repeatabiity Suppy votage Current consumption Output Output operation Short-circuit protection Response time Operation indicator % or ess of operation distance 5 % or ess of operation distance Aong sensing axis: mm.9 in or ess, Perpendicuar to sensing axis:. mm.8 in or ess (with white non-gossy ) <NPN output type> NPN open-coector transistor Maximum sink current: ma Appied votage: V DC or ess (between output and V) Residua votage: V or ess (at ma sink current) V or ess (at 6 ma sink current) to V DC ± % Rippe P-P % or ess ma or ess Switchabe either Detection-ON or Detection-OFF Incorporated ms or ess Orange ED (ights up when the output is ON) Stabiity indicator Green ED (ights up under stabe operating condition) (Note ) Distance adjuster mode Automatic interference prevention function (Note ) Environmenta resistance SPECIFICATIONS Standard type Protection 5-turn mechanica adjuster <PNP output type> PNP open-coector transistor Maximum source current: ma Appied votage: V DC or ess (between output and +V) Residua votage: V or ess (at ma source current) V or ess (at 6 ma source current) BGS / FGS functions Switchabe with wiring of sensing mode seection input Incorporated IP67 (IEC) Ambient temperature -5 to +55 C - to + F (No dew condensation or icing aowed), Storage: - to +7 C - to +58 F Ambient humidity Ambient iuminance Votage withstandabiity Insuation resistance Vibration resistance Shock resistance 5 to 85 % RH, Storage: 5 to 85 % RH Incandescent ight:, x at the ight-receiving face, V AC for one min. between a suppy terminas connected together and encosure MΩ, or more, with 5 V DC megger between a suppy terminas connected together and encosure to 5 Hz frequency, mm.8 in doube ampitude in X, Y and Z s for two hours each 5 m/s acceeration ( G approx.) in X, Y and Z s for three times each EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION Emitting eement Spot diameter Materia Cabe Cabe extension ø mm ø.79 in approx. (at 5 mm.969 in distance) Red ED (Peak emission waveength: 65 mm 5.59 in, moduated) ø6.5 mm ø.56 in approx. (at 5 mm.969 in distance) ø9 mm ø.5 in approx. (at mm.97 in distance) ø5 mm ø.59 in approx. (at mm.8 in distance) Encosure: PBT (Poybutyene terephthaate), ens: Poycarbonate, Indicator cover: Poycarbonate. mm -core cabtyre cabe, m 6.56 ft ong Extension up to tota m 8.8 ft is possibe with. mm, or more, cabe. separated Weight Net weight: 55 g approx., Gross weight: 65 g approx. Notes: ) Where measurement conditions have not been specified precisey, the conditions used were an ambient temperature of + C +7. F. ) The adjustabe range stands for the maximum sensing range which can be set with the distance adjuster. The sensor can detect an object mm.79 in [CX-(-P): 5 mm.59 in, CX-(-P): mm.787 in], or more, away. Actua sensing range of the sensor: A Adjustabe range: B object A B CX- / CX- CX- to 5 mm.79 to.969 in to 5 mm.787 to.969 in 5 to mm.59 to.97 in to mm.787 to.97 in to mm.787 to.8 in to mm.575 to.8 in ) Refer to PRECAUTIONS FOR PROPER for operation of the stabiity indicator. ) Note that detection may be unstabe depending on the mounting conditions or the sensing object. In the state that this product is mounted, be sure to check the operation with the actua sensing object. CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. SPECIFICATIONS separated EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S Basic type Thru-beam Retrorefective Type ong sensing range With poarizing fiters ight-on Dark-ON ight-on Dark-ON ight-on Dark-ON NPN output CX-A-C5 CX-B-C5 CX-A-C5 CX-B-C5 CX-9A-C5-Y CX-9B-C5-Y Item PNP output CX-A-P-C5 CX-B-P-C5 CX-A-P-C5 CX-B-P-C5 CX-9A-P-C5-Y CX-9B-P-C5-Y range m.88 ft 5 m 9. ft m 9.8 ft (Note ) Mode No. object ø mm ø.7 in or more opaque object (Note ) Hysteresis Repeatabiity (perpendicuar to sensing axis) Suppy votage Current consumption Output Short-circuit protection Response time Operation indicator Stabiity indicator : 5 ma or ess : ma or ess <NPN output type> NPN open-coector transistor Maximum sink current: ma Appied votage: V DC or ess (between output and V) Residua votage: V or ess (at ma sink current) V or ess (at 6 ma sink current).5 mm. in or ess to V DC ± % Rippe P-P % or ess : ma or ess : ma or ess Incorporated ms or ess ø5 mm ø.969 in or more transparent, transucent or opaque object (Note, ) ma or ess <PNP output type> PNP open-coector transistor Maximum source current: ma Appied votage: V DC or ess (between output and +V) Residua votage: V or ess (at ma source current) V or ess (at 6 ma source current) Orange ED (ights up when the output is ON)(incorporated on the receiver for thru-beam type) Green ED (ights up under stabe ight received condition or stabe dark condition)(incorporated on the receiver for thru-beam type) Power indicator Green ED (ights up when the power is ON) (incorporated on the emitter) Sensitivity adjuster Automatic interference prevention function Environmenta resistance Protection Two units of sensors can be mounted cose together with interference prevention fiters. ( range: 5 m 6. ft) IP67 (IEC) Incorporated (Two units of sensors can be mounted cose together.) Ambient temperature -5 to +55 C - to + F (No dew condensation or icing aowed), Storage: - to +7 C - to +58 F Ambient humidity Ambient iuminance Votage withstandabiity Insuation resistance Vibration resistance Shock resistance 5 to 85 % RH, Storage: 5 to 85 % RH Incandescent ight:, x at the ight-receiving face, V AC for one min. between a suppy terminas connected together and encosure MΩ, or more, with 5 V DC megger between a suppy terminas connected together and encosure to 5 Hz frequency,.5 mm.59 in doube ampitude ( G max.) in X, Y and Z s for two hours each 5 m/s acceeration (5 G approx.) in X, Y and Z s for three times each Emitting eement (moduated) Red ED Infrared ED Red ED Materia Cabe Peak emission waveength 68 nm.7 mi 87 nm. mi 68 nm.7 mi Cabe extension Weight Encosure: PBT (Poybutyene terephthaate), ens: Acryic, Indicator cover: Acryic. mm -core (thru-beam type emitter: -core) cabtyre cabe,.5 m.6 ft ong Extension up to tota m 8.8 ft is possibe with. mm, or more, cabe (thru-beam type: both emitter and receiver) Net : g approx., : g approx. g approx. Gross 5 g approx. g approx. Notes: ) Where measurement conditions have not been specified precisey, the conditions used were an ambient temperature of + C +7. F. ) The sensing range and the sensing object of the retrorefective type sensor are specified for the RF- refector (optiona). The sensing range represents the actua sensing range of the sensor. The sensing ranges itemized in A of the tabe beow may vary depending on the shape of sensing object. Be sure to check the operation with the actua sensing object. range: A object Setting range of the refector: B Refector (Optiona) A B CX-9 to m to 9.8 ft. to m.8 to 9.8 ft ) If sit masks (optiona) are fitted, an object of ø.5 mm ø. in (using round sit mask) can be detected. ) Make sure to confirm detection with an actua sensor before use. RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. I/O CIRCUIT AND WIRING DIAGRAMS NPN output type I/O circuit diagram circuit Tr D D Interna circuit Coor code / Connector pin No. of the connector type (Brown / ) +V (Back / ) oad Output (Note ) + to V DC ± % ZD ma max. ZD (Bue / ) V * (Pink / ) mode seection input (Note, ) User s circuit Notes: ) The emitter of the thru-beam type sensor does not incorporate the output. ) mode seection input is incorporated ony for the CX- adjustabe range refective type. When using the CX-, be sure to wire the sensing mode seection input (pink / ) as mentioned *. Unstabe operation may occur. ) When the mating cabe is connected to the pug-in connector type of CX-, its coor is white. * mode seection input BGS function: Connect to V FGS function: Connect to +V Symbos... D : Reverse suppy poarity protection diode ZD : Surge absorption zener diode Tr : NPN output transistor PNP output type I/O circuit diagram circuit Tr D D ZD ZD Interna circuit Coor code / Connector pin No. of the connector type (Brown / ) +V ma max. (Back / ) Output (Note ) oad (Bue / ) V * (Pink / ) mode seection input (Note, ) User s circuit to V DC ± % Notes: ) The emitter of the thru-beam type sensor does not incorporate the output. ) mode seection input is incorporated ony for the CX- -P adjustabe range refective type. When using the CX- -P, be sure to wire the sensing mode seection input (pink / ) as mentioned *. Unstabe operation may occur. ) When the mating cabe is connected to the pug-in connector type of CX- -P, its coor is white. * mode seection input BGS function: Connect to V FGS function: Connect to +V Symbos... D : Reverse suppy poarity protection diode ZD : Surge absorption zener diode Tr : PNP output transistor + Wiring diagram Brown oad Back (Note ) Bue * Pink (Note, ) + to V DC ± % Notes: ) The emitter of the thru-beam type sensor does not incorporate the back wire. ) The pink wire is incorporated ony for the CX- adjustabe range refective type. When using the CX-, be sure to wire the pink wire as mentioned *. Unstabe operation may occur. ) When the mating cabe is connected to the pug-in connector type of CX-, its coor is white. * mode seection input BGS function: Connect to V FGS function: Connect to +V Connector pin position M8 pug-in connector type mode seection input (Note ) +V Output (Note ) V M pigtaied type Not connected V +V Output (Note ) Notes: ) The emitter of the thru-beam type sensor does not incorporate the output. ) mode seection input is incorporated ony for the CX- adjustabe range refective type. When using the CX-, be sure to wire the sensing mode seection input (pink / ). Unstabe operation may occur. Wiring diagram Brown Back (Note ) Bue * Pink (Note, ) oad + to V DC ± % Notes: ) The emitter of the thru-beam type sensor does not incorporate the back wire. ) The pink wire is incorporated ony for the CX- -P adjustabe range refective type. When using the CX- -P, be sure to wire the pink wire as mentioned *. Unstabe operation may occur. ) When the mating cabe is connected to the pug-in connector type of CX- -P, its coor is white. * mode seection input BGS function: Connect to V FGS function: Connect to +V Connector pin position M8 pug-in connector type mode seection input (Note ) +V Output (Note ) V M pigtaied type Not connected V +V Output (Note ) Notes: ) The emitter of the thru-beam type sensor does not incorporate the output. ) mode seection input is incorporated ony for the CX- -P adjustabe range refective type. When using the CX- -P, be sure to wire the sensing mode seection input (pink / ). Unstabe operation may occur. EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
5 Compact Photoeectric CX- SERIES Ver. SENSING CHARACTERISTICS (TYPICA) Pease contact our office for the sensing characteristics of CX- and CX-8. separated EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Setting distance (m ft) CX- Parae deviation Anguar deviation Parae deviation with round sit masks (ø.5 mm ø. in).88 5 6. 5.78 7.87 7.87 5.78 eft Center Right Parae deviation with round sit masks (ø mm ø.79 in) Setting distance (m ft) Setting distance (m ft) 6.56.8 Sit on one side Sit on both sides 5 5.97.969.969.97 eft Center Right CX- Parae deviation 65.67 5 9..88 5 6., 5 5, 9.7 9.685 9.685 9.7 eft Center Right Parae deviation with round sit masks (ø mm ø.79 in) Setting distance (m ft). 9.8 6.56.8 Sit on one side Sit on both sides 5.78 7.87 7.87 5.78 eft Center Right Setting distance (m ft).88 5 6. θ eft Center Right Operating ange θ ( ) Parae deviation with rectanguar sit masks (.5 6 mm..6 in) Setting distance (m ft) Setting distance (m ft) 6.56.8 Horizonta Sit on one side Vertica Sit on one side Horizonta Sit on Sit on both sides both sides Vertica Horizonta Vertica 5 5.97.969.969.97 (Down) eft Center Right (Up) Anguar deviation 65.67 5 9..88 5 6. θ eft Center Right Operating ange θ( ) Parae deviation with rectanguar sit masks (.5 6 mm..6 in) Setting distance (m ft). 9.8 Sit on one side Horizonta Sit on one side Vertica Sit on both sides Horizonta and Vertica 6.56 Horizonta Vertica.8 5.78 7.87 7.87 5.78 (Down) eft Center Right (Up) Setting distance (mm in) 5.78 7.87 Sit on one side Sit on both sides.787.9.9.787 eft Center Right Parae deviation with rectanguar sit masks ( 6 mm.9.6 in) Setting distance (m ft). 9.8 6.56.8 Horizonta Sit on one side Horizonta Sit on one side Vertica Sit on both sides Horizonta Sit on both sides Vertica 7.87.97.97 7.87 (Down) eft Center Right (Up) Vertica Parae deviation with round sit masks (ø.5 mm ø. in) Setting distance (mm in) 8.96 6.6 5.78 Sit on one side Sit on 7.87 both sides 5 5.97.969.969.97 eft Center Right Parae deviation with rectanguar sit masks ( 6 mm.9.6 in) Setting distance (m ft). 6.56 Horizonta Sit on one side Vertica Sit on one side Horizonta Sit on both sides Horizonta and Vertica Vertica 5.78 7.87 7.87 5.78 (Down) eft Center Right (Up) Thru-beam type Parae deviation with round sit masks (ø mm ø.9 in) Setting distance (mm in) 8.96 5.78 Sit on one side Sit on both sides.575.787.787.575 eft Center Right Parae deviation with rectanguar sit masks ( 6 mm.79.6 in) Setting distance (m ft) 8 6.7 6 9.685. 6.56 Horizonta Sit on one side Horizonta Sit on one side Vertica Sit on both sides Horizonta Sit on both sides Vertica 7.87.97.97 7.87 (Down) eft Center Right (Up) Vertica Thru-beam type Parae deviation with round sit masks (ø mm ø.9 in) Setting distance (m ft) 6.56.5.9.8 Sit on one side.5 Sit on.6 both sides 7.87.97.97 7.87 eft Center Right Parae deviation with rectanguar sit masks ( 6 mm.79.6 in) Setting distance (m ft) 8 6.7 6 9.685. 6.56 Horizonta Sit on one side Horizonta Sit on one side Vertica Sit on both sides Horizonta and Vertica Vertica 8 8.96 5.78 5.78.96 (Down) eft Center Right (Up) Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. 6 SENSING CHARACTERISTICS (TYPICA) Pease contact our office for the sensing characteristics of CX- and CX-8. Setting distance (m ft) CX-9 Retrorefective type CX-9 Retrorefective type Parae deviation Anguar deviation Parae deviation Anguar deviation. 9.8 6.56.8 CX-8 Retrorefective type CX-8 Retrorefective type Parae deviation 8.96 Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) CX- fied CX- fied Refector (RF-) 7.87.97.97 7.87 eft Center Right 6.6 5.78 7.87 5 5.97.969.969.97 eft Center Right.97 5.969 Refector (RF-) mm 7.87 7.87 in White non-gossy.787.9.9.787 eft Center Right 5.78.8 7.87.97 mm 7.87 7.87 in White nongossy.575.787.787.575 eft Center Right Setting distance (m ft). 9.8 anguar deviation Refector 6.56 anguar anguar deviation deviation Refector (RF-) Refector (RF-) θ.8 θ eft Center Right Operating ange θ ( ) Setting distance (mm in) Anguar deviation 8.96 6.6 Refector anguar deviation anguar deviation Refector (RF-) θ 5.78 Refector anguar Refector deviation anguar Refector (RF-) deviation 7.87 θ anguar deviation eft Center Right Operating ange θ ( ) range (mm in) range (mm in) 8 6.7 6 9.685. 6.56 Parae deviation Correation between sensing object size and sensing range.97 5.969 Correation between sensing object size and sensing range 5.78.8 7.87.97 a a mm White non-gossy 5 5.969.97 5.96 7.87 White non-gossy side ength a (mm in) a a mm White nongossy 5 5.969.97 5.96 7.87 White non-gossy side ength a (mm in) Setting distance (m ft) Setting distance (m ft) Refector (RF-) 7.87.97.97 7.87 eft Center Right 6.56.8 Refector (RF-) 7.87.97.97 7.87 eft Center Right 8 6.7 6 9.685. 6.56 anguar deviation Refector (RF-) θ eft Center Right Operating ange θ( ) Anguar deviation Diffuse refective type As the sensing object size becomes smaer than the standard size (white non-gossy mm 7.87 7.87 in), the sensing range shortens, as shown in the eft graph. For potting the eft graph, the sensitivity has been set such that a mm 7.87 7.87 in white non-gossy is just detectabe at a distance of mm.97 in. Diffuse refective type As the sensing object size becomes smaer than the standard size (white non-gossy mm 7.87 7.87 in), the sensing range shortens, as shown in the eft graph. For potting the eft graph, the sensitivity has been set such that a mm 7.87 7.87 in white non-gossy is just detectabe at a distance of mm.8 in. Setting distance (m ft) Setting distance (m ft) 6.56.8 anguar deviation Refector anguar deviation anguar deviation Refector anguar deviation Refector (RF-) θ Refector anguar deviation Refector anguar anguar deviation deviation θ Refector Refector θ (RF-) (RF-) eft Center Right Operating ange θ ( ) EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
7 Compact Photoeectric CX- SERIES Ver. SENSING CHARACTERISTICS (TYPICA) EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION Setting distance (mm in) Setting distance (mm in) range (mm in) CX- fied, 9.7 5 9.685 CX- mm 7.87 7.87 in White nongossy.575.787.787.575 eft Center Right fied 7.87 White N6 mm.97 7.87 7.87 in Non-gossy.79.9.9.79 eft Center Right range (mm in) Correation between sensing object size and sensing range 8.96 5.78 a a mm White nongossy 5 5.969.97 5.96 7.87 White non-gossy side ength a (mm in) Correation between sensing object size and sensing range 7.87.97 a a mm Non-gossy Correation between ightness and sensing range 7.87.97 region range (mm in) White N6 5 5.969.97 5.96 7.87 Non-gossy side ength a (mm in) The sensing region is represented by obique ines in the eft figure. However, the sensitivity shoud be set with an enough margin because of sight variation in products. Distance (mm in) Diffuse refective type As the sensing object size becomes smaer than the standard size (white non-gossy mm 7.87 7.87 in), the sensing range shortens, as shown in the eft graph. For potting the eft graph, the sensitivity has been set such that a mm 7.87 7.87 in white non-gossy is just detectabe at a distance of 8 mm.96 in. Diffuse refective type As the sensing object size becomes smaer than the standard size (white non-gossy mm 7.87 7.87 in), the sensing range shortens, as shown in the eft graph. For potting the eft graph, the sensitivity has been set such that a mm 7.87 7.87 in white non-gossy is just detectabe at a distance of mm 7.87 in. Emitted beam 5 9.8 7.87 5 5.96..97 5.969 ø5 mm ø.97 in ø.5 mm ø.98 in ø mm ø.79 in ø. mm ø.87 in ø mm ø.57 in Visibe spot range separated Dark N N N6 N8 ightness N N N N N5 N6 N7 N8 N9 ight ightness shown on the eft may differ sighty from the actua object condition. CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com
Compact Photoeectric CX- SERIES Ver. 8 SENSING CHARACTERISTICS (TYPICA) CX- Adjustabe range refective type fieds Setting distance: 5 mm.98 in Setting distance (mm in).575.8.787.9.57 CX- White nongossy Gray non-gossy ightness: 5 5 5 mm.969.969 in Non-gossy.79.79 eft Center Right fieds.57 Setting distance: 5 mm.98 in Setting distance (mm in) Setting distance: 5 mm.969 in 8.5 6.6.575.787.57 White nongossy Gray non-gossy ightness: 5 5 5 mm.969.969 in Non-gossy.79.79 eft Center Right Correation between coor (5 5 mm.969.969 in construction ) and sensing range range (mm in) Setting distance (mm in).57 Setting distance: 5 mm.969 in Correation between coor (5 5 mm.969.969 in construction ) and sensing range range (mm in) 5.969 5.98.575.8.787.9.57 5.969 5.98 White Yeow Orange Red Brown Green Bue Gray Back 5 5 mm.969.969 in Non-gossy White nongossy Gray non-gossy ightness: 5.79.79 eft Center Right White Yeow Orange Red Brown Green Bue Gray Back.57 5 mm.969 in 5 mm.98 in Setting distance (mm in) 8.5 6.6.575.787.57 5 mm.969 in 5 mm.98 in These bars indicate the sensing range with the respective coors when the distance adjuster is set to a sensing range of 5 mm.969 in and 5 mm.98 in ong, respectivey, with white coor. The sensing range aso varies depending on materia. 5 5 mm.969.969 in Non-gossy These bars indicate the sensing range with the respective coors when the distance adjuster is set to a sensing range of 5 mm.969 in and 5 mm.98 in ong, respectivey, with white coor. The sensing range aso varies depending on materia. White nongossy Gray non-gossy ightness: 5.79.79 eft Center Right.57 Distance (mm in) Distance (mm in) Emitted beam 8.5 6.6 5.969.575.8.787 Emitted beam ø mm.79 in ø mm.79 in ø mm.8 in ø mm.8 in Correation between materia (5 5 mm.969.969 in) and sensing range range (mm in) Correation between materia (5 5 mm.969.969 in) and sensing range range (mm in) 5.969 5.98 8.5 6.6 5.969.575.8.787 5.969 5.98 White nongossy White nongossy Gray non-gossy (ightness: 5) ø6.5 mm.56 in ø6. mm. in ø5.9 mm. in ø5. mm.9 in Gray non-gossy (ightness: 5) Cardboard Cardboard Pywood Pywood Back rubber Back rubber 5 mm.969 in 5 mm.98 in Adjustabe range refective type 5 mm.969 in 5 mm.98 in These bars indicate the sensing range with the respective objects when the distance adjuster is set to a sensing range of 5 mm.969 in and 5 mm.98 in ong, respectivey, with white non-gossy. These bars indicate the sensing range with the respective objects when the distance adjuster is set to a sensing range of 5 mm.969 in and 5 mm.98 in ong, respectivey, with white non-gossy. EECTRIC EECTRIC IGHT FOW PARTICUAR SIMPE CONTRO PC / TERMINAS VISUAIZATION separated CX- EX- EX- EX- EX- CX- EQ- EQ-5 -S RT-6 Phone: 8.89. - Fax: 888.7.77 - Web: www.crwtr.com - Emai: info@crwtr.com