power supplies with basic functionality and a high level of reliability Single- and three-phase switched-mode power supply units Slim design Large temperature range from 25 C to 70 C The output voltage can be precisely adjusted via the potentiometer on the front Remote monitoring via integrated status relay Three-coloured LED indicators for simple error detection dvanced visual warning at 90 % rated output current International approvals Derating curves Ioutput (% IN) Ioutput (% IN) 480 Watt 120 100 80 60 40 20 0 25 0 20 30 40 50 60 70 mbient temperature ( C) 960 Watt 120 100 80 60 40 20 0 25 0 20 30 40 50 60 70 mbient temperature ( C) General technical data % \ mbient temp. operating / storage temperature 25 C 70 C / 40 C 85 C Max. perm. air humidity (operation) 5 % 95 % RH Degree of protection IP 20 Class of protection I, with connection Pollution degree 2 Insulation voltage input/output 3 kv E/ / 2 kv E/earth / 0.5 kv /earth MTBF > 500.000 h acc. to IEC 1709 (SN29500) without diode module Housing version metal, corrosion resistant Mounting position, installation notice horizontal on mounting rail TS 35, 50 spacing top and bottom for free air circulation Short-circuit protection Yes, automatic restart Overload protection Yes, IU characteristic curve Overtemperature protection Yes, automatic restart EMC / shock / vibration Noise emission acc. to EN55022 Class B Noise iunity tests acc. to EN61000-4-2 (ESD), EN61000-4-3 and EN61000-4-8 (Fields), EN61000-4-4 (Burst), EN61000-4-5 (Surge), EN61000-4-6 (conducted), EN61000-4-11 (Dips) Limiting of mains voltage harmonic currents cc. to EN61000-3-2 Resistance against vibration and shock 1 g acc. to EN50178, shock: 15 g in all directions Electrical safety (applied standards) Electrical equipment of machines cc. to EN60204 Safety transformers for switched-mode power units cc. to EN61558-2-17 Machinery with electronic equipment cc. to EN50178 / VDE0160 Safety extra-low voltage SELV acc. to EN60950-1, LV acc. to EN60204-1 Protective separation / protection against electrical shock VDE0100-410 / acc. to DIN57100-410 Protection against dangerous shock currents cc. to VDE0106-101.4 60790000 20/2015
PRO ECO 72W 24V 3 PRO ECO 120W 24V 5 L () N () L () N () Pay attention to polarity of connection Pay attention to polarity of connection input voltage range frequency range input voltage range current consumption current consumption fuse (internal) / inrush current Recoended back-up fuse voltage Continuous output current @ 24 V Power boost @ 24 V, 60 C OK larm Wire cross-section, rigid Wire cross-section, flexible Wire cross-section, WG/kcmil 100 240 V 85 264 V (Derating @ 100 V ) 80 370 (Derating @ 120 V ) 0.55 @ 230 V / 1.04 @ 110 V 0.22 @ 370 V / 0.68 @ 120 V Yes / max. 40 2 / DI, Safety fuse 6, Char. B, Circuit breaker 2...4, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 3 up to 55 C 3 @ 55 C, 2.25 @ 70 C 3.6 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V > 87 % @ 230 V & 3 4 W / 9.5 W < 1 m > 0.42 @ 230 V / > 0.45 @ 115 V > 100 ms @ 230 V / > 20 ms @ 115 V 125 / 34 / 100 / 0.5 kg 3 for L/N/ 5 (,,, - -) 0.5/6 0.5/6 26/12 26/12 6 6 100 240 V 85 264 V (Derating @ 100 V ) 80 370 (Derating @ 120 V ) 1.26 @ 230 V / 2.24 @ 110 V 0.39 @ 370 V / 1.16 @ 120 V Yes / max. 40 4 / DI, Safety fuse 6, Char. B, Circuit breaker 3...5, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 5 up to 55 C 5 @ 55 C, 3.75 @ 70 C 6 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V > 87 % @ 230 V & 5 4 W / 15 W < 1 m > 0.47 @ 230 V / > 0.56 @ 115 V > 80 ms @ 230 V / > 20 ms @ 115 V 125 / 40 / 100 / 0.6 kg 3 for L/N/ 6 (,,,, - -) 0.5/6 0.5/6 26/12 26/12 6 6 PRO ECO 72W 24V 3 1 69470000 PRO ECO 120W 24V 5 1 69480000 60790000 20/2015.5
PRO ECO 240W 24V 10 PRO ECO 480W 24V 20 L () N () L () N () Pay attention to polarity of connection Pay attention to polarity of connection input voltage range frequency range input voltage range current consumption current consumption fuse (internal) / inrush current Recoended back-up fuse voltage Continuous output current @ 24 V Power boost @ 24 V, 60 C OK larm Wire cross-section, rigid Wire cross-section, flexible Wire cross-section, WG/kcmil 100 240 V 85 264 V (Derating @ 100 V ) 80 370 (Derating @ 120 V ) 1.23 @ 230 V / 2.47 @ 110 V 1.18 @ 370 V / 2.4 @ 120 V Yes / max. 15 4 / DI, Safety fuse 10, Char. B, Circuit breaker 3...4, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 10 up to 55 C 10 @ 55 C, 7.5 @ 70 C 12 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V > 90 % @ 230 V & 10 3 W / 24 W < 1 m > 0.93 @ 230 V / > 0.99 @ 115 V > 20 ms @ 230 V / > 20 ms @ 115 V 125 / 60 / 100 / 1 kg 3 for L/N/ 6 (,,,, - -) 0.5/6 0.5/6 26/12 26/12 0.5/0.6 0.5/0..6 6 6 100 240 V 85 264 V (Derating @ 100 V ) 80 370 (Derating @ 120 V ) 2.37 @ 230 V / 5.2 @ 110 V 1.55 @ 370 V / 4.65 @ 120 V Yes / max. 3 6 / DI, Safety fuse 16, Char. B, Circuit breaker 6 8, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 20 up to 55 C 20 @ 55 C, 15 @ 70 C 24 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V > 91 % @ 230 V & 20 5 W / 43 W < 1 m > 0.97 @ 230 V / > 0.99 @ 115 V > 20 ms @ 230 V / > 20 ms @ 115 V yes, max. 3 125 / 100 / 120 / 1.6 kg 3 for L/N/ 7 (,,,, -,-,-) 0.5/6 0.18/6 26/12 26/10 6 7 PRO ECO 240W 24V 10 1 69490000 PRO ECO 480W 24V 20 1 69510000.6 60790000 20/2015
PRO ECO 960W 24V 40 L () N () Pay attention to polarity of connection input voltage range frequency range input voltage range current consumption current consumption fuse (internal) / inrush current Recoended back-up fuse voltage Continuous output current @ 24 V Power boost @ 24 V, 60 C OK larm Wire cross-section, rigid Wire cross-section, flexible Wire cross-section, WG/kcmil 100 240 V 85 264 V (Derating @ 100 V ) 80 370 (Derating @ 120 V ) 4.6 @ 230 V / 9.9 @ 110 V 2.9 @ 370 V / 9 @ 120 V Yes / max. 3 16 / DI, Safety fuse 20, Char. B, Circuit breaker 16, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 40 up to 50 C 40 @ 50 C, 24 @ 70 C 48 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V > 93 % @ 230 V & 40 6 W / 76 W < 1 m > 0.97 @ 230 V / > 0.99 @ 115 V > 20 ms @ 230 V / > 20 ms @ 115 V yes, max. 3 125 / 160 / 120 / 2.9 kg 3 for L/N/ 7 (,,,,, - -) 0.18/6 0.5/16 0.5/2.5 2.5/10 26/10 22/8 0.5/0.6 1.2/1.5 7 12 PRO ECO 960W 24V 40 1 69520000 60790000 20/2015.7
PRO ECO3 120W 24V 5 PRO ECO3 240W 24V 10 L1 () L2 () L3 L1 () L2 () L3 Pay attention to polarity of connection Pay attention to polarity of connection input voltage range frequency range input voltage range current consumption current consumption fuse (internal) / inrush current Recoended back-up fuse 3 x 400...3 x 500 V (Wide-range input) 3 x 340...3 x 575 V / 2 x 360...2 x 575 V 47...63 Hz 450...800 V (max. 500 V in accordance with UL 508) 0.3 @ 3 x 500 V / 0.4 @ 3 x 400 V 0.2 @ 800 V / 0.4 @ 450 V Yes / max. 40 2 / DI, Safety fuse 2...3, Char. C, Circuit breaker 3 x 400...3 x 500 V (Wide-range input) 3 x 340...3 x 575 V / 2 x 360...2 x 575 V 47...63 Hz 450...800 V (max. 500 V in accordance with UL 508) 0.6 @ 3 x 500 V / 0.8 @ 3 x 400 V 0.4 @ 800 V / 0.7 @ 450 V Yes / max. 50 2 / DI, Safety fuse 2...3, Char. C, Circuit breaker voltage Continuous output current @ 24 V Power boost @ 24 V, 60 C OK larm Wire cross-section, rigid Wire cross-section, flexible Wire cross-section, WG/kcmil 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 5 up to 55 C 5 @ 55 C, 3.75 @ 70 C 6 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V 87 % @ 3 x 500 V / 88 % @ 3 x 400 V 6 W / W < 1 m > 0.4 @ 3 x 500 V / > 0.45 @ 3 x 400 V > 40 ms @ 3 x 500 V / > 20 ms @ 3 x 400 V 125 / 40 / 100 / 0.6 kg 4 for L1/L2/L3/ 6 (,,,, - -) 0.18/6 0.5/6 26/10 26/12 8 6 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 10 up to 55 C 10 @ 55 C, 7.5 @ 70 C 12 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V 88 % @ 3 x 500 V / 89 % @ 3 x 400 V 8 W / 26 W < 0.5 m > 0.45 @ 3 x 500 V / > 0.5 @ 3 x 400 V > 40 ms @ 3 x 500 V / > 20 ms @ 3 x 400 V 125 / 60 / 100 / 1 kg 4 for L1/L2/L3/ 6 (,,,, - -) 0.18/6 0.5/6 26/10 26/12 7 6 PRO ECO3 120W 24V 5 1 69530000 PRO ECO3 240W 24V 10 1 69540000.8 60790000 20/2015
PRO ECO3 480W 24V 20 PRO ECO3 960W 24V 40 L1 () L2 () L3 L1 () L2 () L3 Pay attention to polarity of connection Pay attention to polarity of connection input voltage range frequency range input voltage range current consumption current consumption fuse (internal) / inrush current Recoended back-up fuse voltage Continuous output current @ 24 V Power boost @ 24 V, 60 C OK larm Wire cross-section, rigid Wire cross-section, flexible Wire cross-section, WG/kcmil 3 x 400...3 x 500 V (Wide-range input) 3 x 340...3 x 575 V / 2 x 360...2 x 575 V 47...63 Hz 450...800 V (max. 500 V in accordance with UL 508) 1.2 @ 3 x 500 V / 1.5 @ 3 x 400 V 0.7 @ 800 V / 1.2 @ 450 V Yes / max. 50 4 / DI, Safety fuse 3...5, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 20 up to 55 C 20 @ 55 C, 15 @ 70 C 24 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V 89 % @ 3 x 500 V / 90 % @ 3 x 400 V 8 W / 48 W < 0.5 m > 0.41 @ 3 x 500 V / > 0.43 @ 3 x 400 V > 30 ms @ 3 x 500 V / > 20 ms @ 3 x 400 V yes, max. 3 125 / 100 / 120 / 1.3 kg 4 for L1/L2/L3/ 7 (,,,, -,-,-) 0.18/6 0.18/6 26/10 26/10 7 7 3 x 400...3 x 500 V (Wide-range input) 3 x 340...3 x 575 V / 2 x 360...2 x 575 V 47...63 Hz 450...800 V (max. 500 V in accordance with UL 508) 2.15 @ 3 x 500 V / 2.68 @ 3 x 400 V 1.37 @ 800 V / 2.37 @ 450 V Yes / max. 40 6 / DI, Safety fuse 10, Char. B, Circuit breaker 6...8, Char. C, Circuit breaker 24 V ± 1 % 22...28 V (adjustable via potentiometer on front) < 100 ms / < 50 mvss @ 24 V, I R 40 up to 50 C 40 @ 50 C, 24 @ 70 C 48 for 1 min, ED = 5 % 30 35 V 35 V LED Green (U output > 21.6 V ) LED Red (Overload, overtemperature, short-circuit, U output < 20.4 V ) Yes / NO contact / max. 30 V / 1 voltage > 21.6 V / < 20.4 V 90 % @ 3 x 500 V / 91 % @ 3 x 400 V 5 W / 95 W < 1 m > 0.56 @ 3 x 500 V / > 0.56 @ 3 x 400 V > 25 ms @ 3 x 500 V / > 20 ms @ 3 x 400 V yes, max. 3 125 / 160 / 120 / 2.5 kg 4 for L1/L2/L3/ 7 (,,,, -,-,-) 0.18/6 0.5/16 0.5/2.5 2.5/10 26/10 22/8 0.5/0.6 1.2/1.5 7 12 PRO ECO3 480W 24V 20 1 69550000 PRO ECO3 960W 24V 40 1 69560000 60790000 20/2015.9
connectpower diode module CP DM 10 CP DM 20 E1 E2 V V V V E1 E2 V V -V V -V E1 E2 -V E1 E2 -V voltage current voltage current mbient temperature (operational) Storage temperature Degree of efficiency at max. load Mounting position, installation notice Installation advice Weight 40 V max. 2 x 0...10 max. U in - 0.5 V typical 0...20 max. or 10 max. for redundancy operation -10 C...55 C -20 C...85 C 95.5% horizontally, on terminal rail TS 35 Space: side 2 cm; above/below 10 cm 0.4 kg CE; culus; curus 40 V max. 2 x 0...20 max. U in - 0.5 V typical 0...40 max. or 20 max. for redundant operations -10 C...55 C -20 C...85 C 97.5% horizontally, on terminal rail TS 35 Space: side 2 cm; above/below 10 cm 0.4 kg CE; culus; curus Dimensions Clamping range (nominal / min. / max.) Depth x width x height 4 / 0. / 6 4 / 0. / 6 110 / 55.5 / 125 110 / 55.5 / 125 4 / 0. / 6 10 / 0.32 / 16 110 / 55.5 / 125 110 / 55.5 / 125 CP DM 10 1 8710620000 CP DM 20 1 8768650000 ccessories.10 60790000 20/2015
- ccessories Small metal foot Large metal foot Small plastic foot Large plastic foot MT 30 MF 12520000 MT 45 MF 12510000 MT 30 BK 1168970000 MT 45 BK 1962250000 Small wall mounting Large wall mounting CP WLLDPTER 30 MM 61870000 CP WLLDPTER 45 MM 61850000 Small screwdriver Blade type Size/F a b c SDIK PH1 1.00 80 9008570000 SDIS 0.5X3.0X100 B 0.5 3 100 9008380000 Markers End bracket For DIN rail TS 35 Colour Qty. SM 18/9.5 K MC NE WS white 200 1248580000 Polyamide with fibre glass, screwable Colour Torque Qty. WEW 35/1 SW black 1.2 50 1162600000 60790000 20/2015.11