Chicken Coop OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. -MODEL # YTF-100CC- 12232015
Thank you very much for choosing this product! For future reference, please complete the owner s record below: Model: YTF-100CC _ Purchase Date: Save the receipt, the warranty, and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This product is designed for certain applications only. The manufacturer cannot be responsible for issues arising from modification. We strongly recommend that this product not be modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted us to determine if it can, or should, be performed on the product. For technical questions please call 1-218-943-6290. TECHNICAL INFORMATION Item Description Dimensions 59 x 27.5 x 41.35 Construction Fir wood Nesting Areas 2 Roosting Bars 2 Hardware Stainless Steel Mesh Construction.8 mm wire Chicken Capacity 4 IMPORTANT SAFETY INFORMATION WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury. CAUTION: Do not allow persons to operate or assemble this product until they have read this manual and have developed a thorough understanding of how it works. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator. DO NOT: Allow children to play in, on, or around this product. SAVE THESE INSTRUCTIONS 2
WORK AREA Keep work area clean, free of clutter, and well-lit. Cluttered and dark work areas can cause accidents. Keep children and bystanders away while assembling this product. PERSONAL SAFETY Use safety apparel and equipment. Use safety glasses with side shields that comply with current national standards, while assembling this product. This applies to all persons in the work area. Also use non-skid safety shoes, hard hats, gloves, dust collection systems, and hearing protection when needed. CHICKEN COOP USE AND CARE Do not modify this product in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which this product was designed. Always check for damaged or worn-out parts before using this product. Broken parts will affect operation. Replace or repair damaged or worn parts immediately. ASSEMBLY Step #1: Attach the Front Panel (A) and the Rear Panel (B) to the Left Panel (C), Center Panel (D) and Right Panel (E) using sixteen Screws (1). Insert the Drawer Panel (F) as shown in the illustration. Left Panel (C) Center Panel (D) Rear Panel (B) Drawer Panel (F) Front Panel (A) Right Panel (E) 3
Step #2: Open the wire door and place the Ramp (H) by its hooks onto the door frame. Insert two Roosting Bars (G) widthwise inside the pen. Open the house door and insert two Roosting Bars (G). Roosting Bars (G) Roosting Bars (G) Ramp (H) Step #3: Attach the Roof Panel (I) to the Rear Panel (B) of the house using nine Screws (2). Roof Panel (I) 4
Step #4: Using the Roof Support Poles (J), open the Roof Panel (I). Attach both Support Chains (K) as shown in the illustration. Roof Support Poles (J) Roof Support Chains (K) Step #5: Attach the Left Nesting Box Panel (L) and the Right Nesting Box Panel (M) to the Left House Panel (C) using four Bolts (3) and four Nuts (4). Insert the Nesting Box Floor Panel (N). Attach the Rear Nesting Box Panel (O) using four Screws (5). Insert the Nesting Box Partition (P) into the slots inside the Nesting Box. Nesting Box Floor Panel (N) Left Nesting Box Panel (M) Nesting Box Partition (P) Rear Nesting Box Panel (O) Right Nesting Box Panel (L) 5
Step #6: Install the Nesting Box Roof Panel (Q) with its hinges using four Screws (2). Nesting Box Roof Panel (Q) Step #7: Attach the Looped Door Handle (R) to the Looped Door Handle Rod (S) using one Bolt (6) and one Nut (7). Looped Door Handle Rod (S) Looped Door Handle (R) MAINTENANCE Cleaning Instructions: Clean with water and mild soap. Avoid harsh detergents. Dry completely. 6
PARTS DIAGRAM PARTS LIST Part # Description Qty. Part # Description Qty. A Front Panel 1 O Rear Nesting Box Panel 1 B Rear Panel 1 P Nesting Box Partition 1 C Left Panel 1 Q Nesting Box Roof Panel 1 D Center Panel 1 R Looped Door Handle 1 E Right Panel 1 S Looped Door Handle 1 Rod F Drawer Panel 1 1 Screw, M4 40mm 16 G Roosting Bar 4 2 Screw, M3 16mm 13 H Ramp 1 3 Bolt, M6 55mm 4 I Roof Panel 1 4 Nut, M6 4 J Roof Support Pole 2 5 Screw, M4 35mm 4 K Roof Support Chain 2 6 Bolt, M4 10mm 1 L Left Nesting Box Panel 1 7 Nut, M4 1 M Right Nesting Box Panel 1 8 Hinges 4 N Nesting Box Floor Panel 1 9 Eye loops 4 10 Latch 4 For technical questions, please call 1-218-943-6290. 7
WARRANTY One-year limited parts warranty. BAC PO BOX 155 Miltona, MN 56354 Made in China 8