ULTRASONIC D. Compact ultrasonic heat meter

ULTRASONIC D Compact ultrasonic heat meter Applications ULTRASONIC D is a compact ultrasonic heat meter used for measuring energy in heating and cooling plants in facility management systems as well as in local and district heating systems. Available as a PN16 threaded or PN25 flanged version, it is ideal for nominal flows from 0.6 to 6 m 3 /h and product temperatures from 5 to 130 C (150 > 3.5 m 3 /h). VD 6-350 d 09.2005 Features Compact ultrasonic heat meter Temperature range from 5 to 130 C (150 C for flow > 3.5 m 3 /h), special version available for cooling applications Sound reflectors designed for optimal flow Certified measuring range 1:250, Class 2 Can be updated with an M-Bus interface and 2 pulsed inputs or outputs Stores the data of the past 24 months and 440 meter readings along with error status Battery with 12- or 16-year lifetime or 24 VAC or 230 VAC power pack module Benefits Static measurement principle with no moving parts; insensitive to grit Accurate heat measurement in heating and cooling plants Low pressure loss High accuracy Cost-effective remote reading of 2 contact water meters via M-Bus Transparent data recording The optimum power supply for every application

Applications ULTRASONIC D is a fully-electronic compact heat meter for measuring heat in heating and cooling plants used in facility management systems and in local and district heating systems. Additional modules enable data to be transmitted via M-Bus or pulsed outputs. Another module with two pulsed inputs allows low-cost readout of two contact water meters via the M-Bus. Its ultrasonic measuring principle ensures that the unit is unaffected by small particles such as sand or limestone grit. Instrument design The compact ultrasonic heat meter consists of an ultrasonic flow sensor, two temperature sensors, for measuring forward and return flow temperatures, and an electronic totalizer. This totalizer can be mounted either on the flowmeter or on a wall. It contains the electronics for evaluating, displaying and protocolling the measurement signals of the flowmeter and temperature sensors. A wide variety of information is shown on the easy-to-read 7-character display with units and easy-to-understand symbols. The various display s and sequences can be called up by pushbutton. Downtimes and errors are automatically recorded and shown on the LC display. All critical data (measured values, equipment parameters and types of error) are periodically stored in a non-volatile memory (EEPROM). ULTRASONIC D is equipped with a ZVEI optical interface with an EN 1434 M-Bus protocol. This interface is also used for communicating with software to set the parameters. The unit is available with the following power supplies: battery with 12-year lifetime (3.0 VDC lithium battery) battery with 16-year lifetime (3.6 VDC Lithium battery, optional) power pack for 24 VAC power pack for 230 VAC Caption: By a special design of the reflectors the flow is accelerated so that deposits are avoided. The flow sensor with it ultrasonic technology guarantees very high measuring accuracy. It can be used either in the forward or return flow. The flow sensor complies with the requirements of EN 1434 / Class 2 and 3 with a measuring range of 1:250. ULTRASONIC D operates with paired Pt 500 temperature sensors using two-wire connections according to EN 1434. Optional modules Communication modules The following communication modules are available as options: M-Bus module to EN 1434 RS232 module (serial interface) with M-Bus protocol Module with two pulsed inputs The optional pulsed input module provides low-cost remote readout of two contact water meters via the M-Bus module of the ULTRASO- NIC D. Module with two pulsed outputs, error contact The optional pulsed output module provides two pulsed outputs with freely-programmable pulse weighting. Pulses for energy and volume are standard. Other values for the pulsed outputs can be configured as required: Energy tariff 1, 2 Tariff mode 1, 2, setpoint switching Error status for energy or volume 2

Combining modules The following table shows the possible combination of modules (2 slots): 2 pulsed 2 pulsed M-Bus RS232 inputs outputs 2 pulsed inputs 2 pulsed outputs Event memory Up to 31 entries of the following events can be recorded in the non-volatile memory: Checksum error on M-Bus transmission Error with temperature measurement Error with ultrasonic time-of-flight measurement Start and end of check mode Month memory ULTRASONIC D has an archived memory covering 24 months.the following values are stored in the EEPROM at the beginning of the month: Date Tariff specification 1 Maximum flow for the month Energy Tariff specification 2 Maximum output for the month Energy tariff 1 VolumeDate of maximum flow for the month Energy tariff 2 Meter for error days Date of maximum output for the month Log memory The log memory has 440 locations and can carry out a detailed analysis of the data: Time interval Duration Values Hours Days 1 min. - 6 min. in 1 min. steps 7,3-44 0,3-1,8 Date and time 10 min. 73 3.1 Energy, volume 12 min 88 3.7 Forward temperature, return temperature 15 min 110 4.6 Energy tariff 1, Energy tariff 2, 20 min 147 6.1 Tariff specification 1, Tariff specification 2, 30 min 220 9.2 Error status 60 min 440 18.3 Excess time temperature, excess time flow, 24 h (standard) 10'560 440 Meter for error days Note A readout of the log memory via the M-Bus or optical interface is only possible with special ULTRASONIC D service software. Peak value memory The totalizer stores maximum values for output and flow over a preselected time interval in the EEPROM (for 6, 15, 30 or 60 minutes or for 24 hours, standard setting: 60 min.). 3

Month Tariff Pulsed input Information Billing date Main Tariff function ULTRASONIC D can separately record energy and volume data for two different tariffs. The changeover can be programmed for a value that moves outside a set range (return flow temperature, temperature difference, output or flowrate). Tariff specification Range of setpoint values Accuracy T 1... 190 C 1 C T R 1... 190 C 1 C P 1... 255 kw 1 kw Q 100... 25 500 l/h 100 l/h Adjusting the display The LC display consists of a 7-character value with units as well as a wide range of symbols. The display can be adjusted using the operating key: Press key briefly < 3 sec to move to the next display within the same Press key continuously > 3 sec to move to the first display in the next The "Energy" window of the main (sequence 1.1) is the home display. If the key has not been pressed for approx. 4 minutes, the meter automatically returns to the power save mode. When the key is again pressed the meter returns to the home display. Display s The ULTRASONIC D display has six operating s. Some of the windows show a number of values (2 to 7). These are displayed one after the other in a 4 sec. cycle. 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.1 2.2 2.3 2.4 2.5 2.6 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 4.1 1 4.2 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10... 6.1 6.2 6.3 6.24 4

Overview of display s and sequences All values are shown in sequence when the key is pressed briefly. A text in "inverted commas" is shown as an equivalent text, e.g. "Accd1". ([OFF] indicates that the display is not shown in the standard configuration. It can be activated with the software for setting parameters. Loop Sequence Window 1 Window 2 Window 3 1 1.1 Summated energy Main 1.2 Volume 1.3 Flow 1.4 Output 1.5 Forward flow temperature Return flow temperature 1.6 Differential temperature 1.7 Hours in operation 1.8 Maximum output for the month Date 1.9 Error code 1.10 Display test 1.11[OFF] Tariff output 1 1.12[OFF] Tariff output 2 1.13[OFF] In 1 Pulse input counter 1 1.14[OFF] In 2 Pulse input counter 2 Loop Sequence Window 1 Window 2 Window 3 [OFF] Window 4 2 2.1 Billing date 1 Date Billing date 1 Energy Billing date 1 Volume Accd 1 Billing date 2.2 Prev. year billing date 1 Prev. year billing date 1 Energy Prev. year billing date 1 Volume Accd 1 2.3 Accd 1 Future billing date 1 2.4 Billing date 2 Billing date 2 Energy Billing date 2 Volume Accd 2 2.5 Prev. year billing date 2 Prev. year billing date 2 Energy Prev. year billing date 2 Volume Accd 2 2.6 Accd 2 Future billing date 1 Loop Sequence Window 1 Window 2 Window 3 3 3.1 Current date Info 3.2 SEC_Adr Secondary address 3.3 Pri_Adr Primary address 3.4 Pt 100 or Pt 500 3.5 Maximum monthly flow Date max. flow 3.6 Maximum monthly output Date max. output 3.7 Integration interval max. values 3.8 Number of error days 3.9 Out1 Pulse weighting and unit pulsed output 1 3.10 Out2 Pulse weighting and unit pulsed output 2 Loop Sequence Window 1 Window 2 Window 3 4 4.1 In1 Summated volume 1 Pulse weighting 1 Pulsed input 4.2 In2 Summated volume 2 Pulse weighting 2 4.3[OFF] Billing date 1 In1 Billing date 1 pulsed meter 1 4.4[OFF] Billing date 1 Date In2 Billing date 1 pulsed meter 2 4.5[OFF] Prev. year billing date 1 In1 Prev. year billing date 1 pulsed meter 1 4.6[OFF] Prev. year billing date 1 In2 Prev. year billing date 1 pulsed meter 2 4.7[OFF] Billing date 2 In1 Billing date 2 pulsed meter 1 4.8[OFF] Billing date 2 In2 Billing date 2 pulsed meter 2 4.9[OFF] Prev. year billing date 2 In1 Prev. year billing date 2 pulsed meter 1 4.10[OFF] Prev. year billing date 2 In2 Prev. year billing date 2 pulsed meter 2 Loop Sequence Window 1 Window 2 Window 3 5 5.1[OFF] Actual tariff energy 1 Type of tariff (e.g. `t 01 ) Tariff setpoint 1 Tariff 5.2[OFF] Actual tariff energy 2 Type of tariff 2 (e.g. `t 02 ) Tariff setpoint 2 5.3[OFF] Billing date 1 Billing date 1 tariff energy 1 Accd 1 5.4[OFF] Billing date 1 Billing date 1 tariff energy 2 Accd 1 5.5[OFF] Prev. year billing date 1 Prev. year billing date 1 tariff energy 1 Accd 1 5.6[OFF] Prev. year billing date 1 Prev. year billing date 1 tariff energy 2 Accd 1 5.7[OFF] Billing date 2 Billing date 2 tariff energy 1 Accd 2 5.8[OFF] Billing date 2 Billing date 2 tariff energy 2 Accd 2 5.9[OFF] Prev. year billing date 2 Prev. year Billing date 2 tariff energy 1 Accd 2 5.10[OFF] Prev. year billing date 2 Prev. year billing date 2 tariff energy 2 Accd 2 5

Loop Sequence Window 1 Window 2 Window 3 Window 4 Window 5 Window 6 Window 7 [OFF] [OFF] 6 6.1 Prev. month Energy Tariff energy 1 Tariff energy 2 Volume Max. flow Max. output Month 6.2 Month 1 Energy Tariff energy 1 Tariff energy 2 Volume Max. flow Max. output 6.3 Month 2 Energy Tariff energy 1 Tariff energy 2 Volume Max. flow Max. output... 6.24 Month 23 Energy Tariff energy 1 Tariff energy 2 Volume Max. flow Max. output Dimensions Nominal size qp = 0.6 m 3 /h qp = 1.0 / 1.5 m 3 /h qp = 2.5 m 3 /h qp = 3.5 m 3 /h qp = 6 m 3 /h L (mm) 110 130 190 110 130 190 130 190 260 260 L1 (mm) 190 230 190 190 230 190 230 190 260 260 260 260 L2 (mm) 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 B (mm) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 R (mm) 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 H (mm) 78 80 80 80 8 80 80 80 80 80 80 84.5 84.5 84.5 84.5 84.5 84.5 h (mm) 14.5 18 18 47.5 14.5 18 18 47.5 18 18 47.5 23 50 62.5 23 50 62.5 AGZ G 3 /4B G 1 B G 1 B Fl. G 3 /4B G 1 B G 1 B Fl. G 3 /4B G 1 B Fl. G 1 1 /4 B Fl. Fl. G 1 1 /4 B Fl. Fl. 6 DN 15 DN 20 DN 20 DN 20 DN 15 DN 20 DN 20 DN 20 DN 15 DN 20 DN 20 DN 25 DN 32 DN 25 DN 32 AGV R 1 /2 R 3 /4 R 3 /4 R 1 /2 R 3 /4 R 3 /4 R 3 /4 R 3 /4 D (mm) 105 105 105 114 139 114 139 d (mm) 14 14 14 14 18 14 18 Flange F (mm) 95 95 95 100 125 100 125 Hole circle K (mm) 75 75 75 85 100 85 100

Technical data Energy meter 0.6 1.0 / 1.5 2.5 3.5 6 Basic features Ambient class Ingress protection EN 1434 Class C / A IP54 (heat meters) / IP64 (cold meters) Type Static compact heat meter acc. to EN 1434 Measurement Display Display Units ultrasonic volumetric measurement LC display, 7-character MWh-kWh-GJ-Gcal-MBtu Values, total 9 999 999-999 999.9-99 999.99-9 999.99 Values displayed Flow rates Output - Energy Flow rate - Temperature Maximum qs m 3 /h 1.2 1.2 1.2 1.2 2/3 2/3 2/3 2/3 5 5 5 7 7 7 12 12 12 Nominal rate qp m 3 /h 0.6 0.6 0.6 0.6 1/1.5 1/1.5 1/1.5 1/1.5 2.5 2.5 2.5 3.5 3.5 3.5 6 6 6 Minimum qi l/h 6 6 6 6 10/6 10/6 10/6 10/6 10 10 10 35 35 35 24 24 24 Threshold value l/h 1 1 1 1 2.5 2.5 2.5 2.5 4 4 4 10 10 10 10 10 10 Temp. range of volumetric sensor C 5-130 5-130 5-130 5-130 5-130 5-130 5-130 5-130 5-130 5-130 5-130 5-150 5-150 5-150 5-150 5-150 5-150 Pressure loss at qp p mbar 95 95 95 95 120 120 120 120 100 100 100 44 44 44 128 128 128 Max. operating pressure PN bar 16(25) 16(25) 16(25) 25 16(25) 16(25) 16(25) 25 16(25) 16(25) 25 25 25 25 25 25 25 Nominal width DN mm 15 20 20 FL20 15 20 20 FL20 20 20 FL20 25 FL25 FL32 25 FL25 FL32 Face-to-face length mm 110 130 190 190 110 130 190 190 130 190 190 260 260 260 260 260 260 Input Temp. sensor Type Pt100 or Pt500 as two-wire version Sensor flow ma Pt 100 peak < 8; rms < 0.015 Pt 500 peak < 2; rms < 0.012 Measuring cycle T s Mains power: 1 s Battery: 16 s Max. temp. difference Θmax K 177 acc. to certification Min. temp. difference Θmin K 3 acc. to certification Min. temp. difference Θ K 0.25 Threshold value Temp. measuring range Θ C -9.9...189.9 Power supply Operating voltage UN VDC 3.0V / 3.6V (lithium battery) / 230 V AC / 24 V AC Other Weight Complete g 750 760 780 2850 750 760 780 2850 760 780 2850 1500 3500 4800 1500 3500 4800 Flow resistance coefficient Zeta 21.3 67.5 67.5 67.5 4.3 13.6 13.6 13.6 4.0 4.0 4.0 2.8 2.8 7.4 2.8 2.8 7.4 Pressure loss and accuracy acc. to EN 1434 Class 2 7

Ordering The ULTRASONIC D range of flowmeters ranges from nominal flow qp = 0.6 m 3 /h up to 6 m 3 /h with various face-to-face lengths and totalizer configurations: A typical example from our product range Short text qp DN Connection L Kvs p PN Power Parts at qp supply No. m 3 /h mm Zoll mm m 3 /h mbar bar 12-year lifetime battery, without M-Bus ULTRASONIC D Qp 0.6,110-G3/4 B12J TF 0.6 15 G 3/4 B 110 1.9 95 16 Bat.12J 93594 ULTRASONIC D Qp 1.5,110-G3/4 B12J TF 1.5 15 G 3/4 B 110 4.2 25 16 Bat.12J 93595 ULTRASONIC D Qp 2.5,130-G1 B12J TF 2.5 20 G 1 B 130 8.0 100 16 Bat.12J 93596 ULTRASONIC D Qp 2.5,190-G1 B12J TF 2.5 20 G 1 B 190 8.0 100 16 Bat.12J 93597 ULTRASONIC D Qp 3.5,260-G5/4 B12J 3.5 25 G 5/4 B 260 9.0 150 16 Bat.12J 93598 ULTRASONIC D Qp 6,260-G5/4 B12J 6.0 25 G 5/4 B 260 16 170 16 Bat.12J 93599 12-year lifetime battery, with M-Bus ULTRASONIC D Qp 0.6,110-G3/4 B12J M-TF 0.6 15 G 3/4 B 110 1.9 95 16 Bat.12J 93600 ULTRASONIC D Qp 1.5,110-G3/4 B12J M-TF 1.5 15 G 3/4 B 110 4.2 25 16 Bat.12J 93601 ULTRASONIC D Qp 2.5,130-G1 B12J M-TF 2.5 20 G 1 B 130 8.0 100 16 Bat.12J 93602 ULTRASONIC D Qp 2.5,190-G1 B12J M-TF 2.5 20 G 1 B 190 8.0 100 16 Bat.12J 93603 ULTRASONIC D Qp 3.5,260-G5/4 B12JM 3.5 25 G 5/4 B 260 9.0 150 16 Bat.12J 93604 ULTRASONIC D Qp 6,260-G5/4 B12JM 6.0 25 G 5/4 B 260 16.0 170 16 Bat.12J 93605 230 VAC, without M-Bus ULTRASONIC D Qp 0.6,110-G3/4 N230 TF 0.6 15 G 3/4 B 110 1.9 95 16 230 V AC 93'606 ULTRASONIC D Qp 1.5,110-G3/4 N230 TF 1.5 15 G 3/4 B 110 4.2 25 16 230 V AC 93'607 ULTRASONIC D Qp 2.5,130-G1 N230 TF 2.5 20 G 1 B 130 8.0 100 16 230 V AC 93'608 ULTRASONIC D Qp 2.5,190-G1 N230 TF 2.5 20 G 1 B 190 8.0 100 16 230 V AC 93'609 ULTRASONIC D Qp 3.5,260-G5/4 N230 3.5 25 G 5/4 B 260 9.0 150 16 230 V AC 93'610 ULTRASONIC D Qp 6,260-G5/4 N230 6.0 25 G 5/4 B 260 16.0 170 16 230 V AC 93'613 24 VAC, with M-Bus ULTRASONIC D Qp 0.6,110-G3/4 N24 M-TF 0.6 15 G 3/4 B 110 1.9 95 16 24 V AC 93614 ULTRASONIC D Qp 1.5,110-G3/4 N24 M-TF 1.5 15 G 3/4 B 110 4.2 25 16 24 V AC 93615 ULTRASONIC D Qp 2.5,130-G1 N24 M-TF 2.5 20 G 1 B 130 8.0 100 16 24 V AC 93616 ULTRASONIC D Qp 2.5,190-G1 N24 M-TF 2.5 20 G 1 B 190 8.0 100 16 24 V AC 93617 ULTRASONIC D Qp 3.5,260-G5/4 N24 M 3.5 25 G 5/4 B 260 9.0 150 16 24 V AC 93618 ULTRASONIC D Qp 6,260-G5/4 N24 M 6.0 25 G 5/4 B 260 16.0 170 16 24 V AC 93619 24 VAC, with M-Bus and 2 pulsed inputs ULTRASONIC D Qp 0.6,110-G3/4 N24 MEE-TF 0.6 15 G 3/4 B 110 1.9 95 16 24 V AC 93620 ULTRASONIC D Qp 1.5,110-G3/4 N24 MEE-TF 1.5 15 G 3/4 B 110 4.2 25 16 24 V AC 93621 ULTRASONIC D Qp 2.5,130-G1 N24 MEE-TF 2.5 20 G 1 B 130 8.0 100 16 24 V AC 93622 ULTRASONIC D Qp 2.5,190-G1 N24 MEE-TF 2.5 20 G 1 B 190 8.0 100 16 24 V AC 93623 ULTRASONIC D Qp 3.5,260-G5/4 N24 MEE 3.5 25 G 5/4 B 260 9.0 150 16 24 V AC 93624 ULTRASONIC D Qp 6,260-G5/4 N24 MEE 6.0 25 G 5/4 B 260 16.0 170 16 24 V AC 93625 Key: B12J: 12-year lifetime battery N24: Mains 24 VAC N230: Mains 230 VAC M: M-Bus EE: 2 pulsed inputs TF: incl. temperature sensors Special versions are available for cooling and cooling/heating plants in change-over operation with dewpoint. Temperature sensors Heat meters up to Qp 2.5 m 3 /h are supplied with paired Pt500 temperature sensors acc. to EN 1434 (ø 5 mm). The sensors are to be ordered separately from Qp 3.5 m 3 /h upwards. Design approval and verification ULTRASONIC D has design approval to EN1434 issued by the PTB. Approval for other countries on request. Instruments for heat measurement are subject to commercial verification in most countries. Equipment for these measuring points is subject to this verification and must be calibrated when their validation date expires. The operator is responsible for compliance with the verification requirements. AQUAMETRO AG AQUAMETRO SA AQUAMETRO AQUAMETRO AQUAMETRO s.r.o. MESSTECHNIK GmbH BELGIUM SPRL Ringstrasse 75 Rue du Jura 10 Zum Panrepel 24 Bd. Lambermont 131 Prosecká 811 / 76a CH-4106 Therwil CH-1800 Vevey D-28307 Bremen B-1030 Bruxelles CZ-190 00 Praha 9 Phone 061 725 11 22 Phone 021 923 51 30 Phone 0421 / 871 64-0 Phone 02 / 241 62 01 Phone 02 / 86 88 77 78 Fax 061 725 15 95 Fax 021 922 58 44 Fax 0421 / 871 64-19 Fax 02 / 216 22 63 Fax 02 / 86 88 95 59 info@aquametro.com info@aquametro.com info.amd@aquametro.com info.amb@aquametro.com info.amc@aquametro.com www.aquametro.com Änderungen vorbehalten / Sous réserve de modifications Modification rights reserved / Copyright AquametroAG A0.5-09.2005 - Art.-Nr. 11892