STANDARD 430E Series Bottom mounted full extension drawer runners Specifications Runner 430E8000 430E7500 430E7000 430E6500 430E6000 430E5500 430E5000 430E4500 430E4000 430E3500 430E3000 430E2500 Nominal Length Inches 32" 30" 28" 26" 24" 22" 20" 18" 16" 14" 12" 10" Minimum Interior Cabinet Depth 803 753 703 653 603 553 503 453 403 353 303 253 (31 5 /8") (29 5 /8") (27 11 /16") (25 3 /4") (23 3 /4") (21 13 /16") (19 13 /16") (17 7 /8") (15 7 /8") (13 7 /8") (11 15 /16") (9 15 /16") Suggested Drawer Length 800 750 700 650 600 550 500 450 400 350 300 250 (31 1 /2") (29 1 /2") (27 9 /16") (25 5 /8") (23 5 /8") (21 11 /16") (19 11 /16") (17 3 /4") (15 3 /4") (13 3 /4") (11 13 /16") (9 13 /16") Over Extension 30 (1-3 /16") At suggested drawer length Cabinet & Drawer Profile Length 800 750 700 650 600 550 500 450 400 350 300 250 (31 1 /2") (29 1 /2") (27 9 /16") (25 5 /8") (23 5 /8") (21 11 /16") (19 11 /16") (17 3 /4") (15 3 /4") (13 3 /4") (11 13 /16") (9 13 /16") 128 128 128 128 96 128 9 37 4 Colors: White or R901 cream 430E8000 (32") 430E7500 (30") 96 430E7000 430E6500 430E6000 (28") (26") (24") 64 430E5500 430E5000 (22") (20") 96 430E4500 430E4000 430E3500 (18") (16") (14") 430E3000 (12") # 6 FH Wood Screw Hole 32 192 430E2500 (10") System Screw Hole or #7 FH wood screw Height Adjustment Slot 9 (3/8") 32 (1-1/4") 37 (1-7/16") 4 (5/32") Setback Cabinet front 8 Subject to technical modifications without notice. 2003
Front Drawer and cabinet specifications Panel Cabinet Installation Cabinet Depth Interior Depth Drawer Profile Mounting Attach through sides or bottom Position profiles flush with front of drawer box. Cabinet Profile Setback 4 (1/8") Note: Install front, back and at least one center screw for maximum load capacity. Mounting Position 37 (1-7/16") 50 (1-15/16") Min. 3 (1/8") Min. Top Clearance Drawer width Drawer length Drawer Length Max. Drawer Height Opening minus 9 (3/8") 6 (1/4") Bottom Clearance 30 (1-3/16") Over Extension Interior Cabinet Width Drawer Width = Interior Cabinet Width - 25 (1") 3 (1/8") Min. Top Clearance Opening Captive Profile Max. Drawer Height Opening minus 9 (3/8") Side Clearance 12.5 (1/2") Captive Profile See page 10 for profile installation 50 Min. (1-15/16") Bottom Clearance 6 (1/4") Subject to technical modifications without notice. 2003 9
STANDARD 430E Series Assembly of bottom mounted full extension drawer runners Cabinet and drawer profile assembly Cabinet profile Intermediate profile Plastic detent stop to top Drawer profile Roller to front 430E Series Profiles (LH) 1. Mount cabinet profile to side panel Rear roller through gap Front hook section over cabinet profile roller LOCK 2. Install intermediate profile 3. Slide intermediate profile to lock into position Drawer profile roller slides over intermediate profile roller and into track Unlock Lock 4. Install drawer profile 5. Engage drawer removal lock 10 Subject to technical modifications without notice. 2003
Accessories a Rear mount sockets for 230M and 230E runners in frame cabinets Synthetic, neutral color Attach with Blum 612TH screws, #6 x 1 /2" trusshead Cannot be used with 430 full extension series 230M RH & LH Socket Set 602320 230E RH & LH Socket Set 601962-VH21 230M RH 602300 230E RH 601960 230M LH 602301 230E LH 601961 Cabinet profile spacers To space runners away from the cabinet side to clear door protrusion on interior roll-out trays. A With split dowel Heavy duty spacer D Two thicknesses available that can be stacked up to 24 ( 15 /16") Synthetic, neutral color A 8 ( 5 /16") with Ø5 ( 3 /16") x 11 320M0188 dowel for linebore mounting 4 8 B C Without split dowel 32 (1-1/4") B C 4 ( 5 /32") stackable 320M0048 8 ( 5 /16") stackable 320M0088 8 19 (3/4") Heavy duty spacer Synthetic, neutral color D 32 (1-1 /4") x 19 ( 3 /4") 602750 Use #6 FH screw that penetrates cabinet side at least 13 ( 1 /2") Use 3 deep thread system screws to attach runner to spacer and spacer to cabinet side Important: Use spacers on front, middle and rear of each cabinet profile for adequate support. Door protectors For pull-out surrounds to prevent damage to doors. Space requirements Assembly Fixed to the underside of the drawer. For 230M and 430E runners. Symmetrical. Epoxy coated steel, with synthetic rollers, cream color. Door protector 298.2200 15 (9/16") 230M runner min 34 (1-5/16") Screws and bumpers Deep thread wood screws Nickel plated #6 x 5 /8", #2 Phillips 606N #6 x 5 /8", #2 POZI 606P Deep thread system screws Pilot bore Ø5 ( 3 /16") hole Nickel plated Drawer bumper stops Cushions drawer closing Self-adhesive back, clear Dia. Thk. Zinc plated #6 x 1 /2", #2 Phillips 612TH 11.5 ( 7 /16"), #2 POZI 661.1150 13 ( 1 /2"), #2 POZI 661.1300 6 ( 1 /4") dia. x 1.5 ( 1 /16") thk. FX4041 10 ( 3 /8") dia. x 3 ( 1 /8") thk. SJ5312 Subject to technical modifications without notice. 2003 11
Assembly tools MINIFIX For precise positioning of cabinet profile fixing screws. For 230M, 230E and 430E runners MINIFIX 65.3300 18 Drawer front adjusters and marking gauge Drawer front adjuster Nylon housing with pre-mounted 8-32 steel nut. For 4-sided drawers. Adjusts height and side-toside by 5 (3/16"). Installation of drawer front adjuster using marking gauges 1 2 10.5 Ø20 1. Bore for front adjusters. Insert marking gauges into drawer front. 2. Align the drawer front to make marks in the drawer box. 8-32 thread Drawer front adjuster 295.1000 3 4 MINIPRESS Ram Ø20 Drill bit MZM.0095 10.5 MOI.ZB20.02 Ø20 Marking gauge For marking center holes for knock-in drawer front adjusters, 295.1000. For wooden 4-sided drawers. 3. Mark fixing positions with a light tap onto the drawer front. 4. Drill Ø5 (3/16") holes through the drawer box. 10 Ø20 5 6 Marking gauge 65.2950 5. Insert drawer front adjusters manually or with a MINIPRESS insertion ram (MZM.0095) 6. Install and adjust drawer front. 12 Subject to technical modifications without notice. 2003
68 62 30 Special application Standard Series with roll-out tray mounted to Blum Universal Drawer Brackets 295.4000 Universal Drawer Bracket 295.4000 Universal Drawer Bracket Mounting Screw M4 x 1/4" Mounting Screw M4 x 1/4" 16 (5/8") 30 (1-3/16") 18 (3/4") 62 (2-1/2") 612TH Screws (#6 x 1/2" Truss Head) 612TH Screws (#6 x 1/2" Truss Head) Roll-out tray with 230M runner Roll-out tray with 430E runner For mounting Blum runners to the floor of a cabinet (roll-out tray). Attach to cabinet with Blum 612TH screws, (#6 x 1 /2" trusshead) 16 48 64 M4 tapped holes Zinc coated (4) per set with M4 screws Universal bracket kit 295.4000 1.5 68 POZI screwdriver and bits a critical tool in full torque application A POZI screwdriver (different from Phillips) is the most crucial tool you can use to assure that full torque is applied to all Blum adjustment screws. POZI screws can be identified by the distinctive tick marks located in the center of the screwhead recess. Tick marks Hand screwdriver #2 POZI DRIVER POZI DRIVER 1 /4" Hex drive for power drivers Magnetic bit holder BIT HOLDER #2 x 1 x 1 /4" POZI drive insert POZI BIT #2x1 Subject to technical modifications without notice. 2003 13