Vectron International Filter specification TFS 2096 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 200 Ω -0.38 pf Output: 75 Ω Characteristics Remark: The nominal frequency f N is fixed at 2096 MHz. The insertion loss a e is defined as loss value determined at f N. Reference level for the relative attenuation a rel of the TFS 2096 is the insertion loss a e. All specified data are met within the operating temperature range. D a t a typ. value tolerance / limit Insertion loss a e 2.8 db max. 3.7 db (reference level) Nominal frequency f N - 2096.0 MHz Passband PB - f N ± 20.0 MHz Passband variation 1.0 db max. 2.0 db Relative attenuation a rel 0.3 MHz... 862 MHz 73 db min. 60 db 862 MHz... 1887.4 MHz 47 db min. 43 db 1887.4 MHz... 2000 MHz 44 db min. 33 db 2190 MHz... 2300 MHz 37 db min. 25 db 2300 MHz... 3000 MHz 42 db min. 35 db 3000 MHz... 6000 MHz 26 db min. 15 db Group delay ripple 2077.4 MHz... 2114.5 MHz 3 ns max. 10 ns Input VSWR within PB 2.0 : 1 max. 2.4 : 1 Output VSWR within PB 1.8 : 1 max. 2.4 : 1 CMRR *** within PB 26 db min. 20 db Input power level - max. 0 dbm Permissible DC voltage - max. 0 V Operable temperature range - - 30 C... + 80 C Operating temperature range OTR - - 20 C... + 50 C Storage temperature range - - 50 C... +125 C Temperature coefficient of frequency TC f ** -46 ppm/k - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) f(hz) = TC f (ppm/k) x (T-T 0) x f CAT (MHz) ***) CMRR : Common Mode Rejection Ratio Generated: Checked / Approved:
Vectron International Filter specification TFS 2096 2/5 Filter characteristic Filter characteristic 0 0 0.091-10 -1 0.082-20 -2 0.073-30 -3 0.064 magnitude in db -40-50 -60 magnitude in db -4-5 -6 0.055 0.046 0.037 delay in µs -70-7 0.028-80 -8 0.019-90 -9 0.01-100 128.3561 521.8849 915.4137 1308.9424 1702.4712 2096 2489.5288 2883.0576 3276.5863 3670.1151 4063.6439 frequency in MHz -10 0.001 2046 2056 2066 2076 2086 2096 2106 2116 2126 2136 2146 frequency in MHz Construction and pin connection (All dimensions in mm) 6 5 4 1,2 Max. N96 E06 1 2 3 Date code 1 Ground 2 Output 3 Ground 4 Input 5 Ground 6 Input 0,1 1 3 3 ±0,15 1,5 6 4 0,6 0,6 0,75 Date code: Year + week E 2014 F 2015 G 2016... 200 Ω / 75 Ω Test circuit 200Ω 75Ω L1 4 2 SAW 6 1, 3, 5
Vectron International Filter specification TFS 2096 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2-27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2-6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 C to 125 C / 15 min. each / 100 cycles DIN IEC 68 part 2 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 9000 reel of empty components at start: min. 300 mm reel of empty components at start including leader: min. 500 mm trailer: min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,5 ± 0,1 t Ko Ct Do Typ Date Code PIN Marker Po D1 P1 P2 Ao Bo G G F E W W 2 Reel (all dimensions in mm) A : 330 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 50 C : 13,0 +0,5/-0,2 A C N W 1 The minimum bending radius is 45 mm.
Vectron International Filter specification TFS 2096 4/5 Air reflow temperature conditions Conditions Exposure Average ramp-up rate (30 C to 217 C) less than 3 C/second > 100 C between 300 and 600 seconds > 150 C between 240 and 500 seconds > 217 C between 30 and 150 seconds Peak temperature max. 260 C Time within 5 C of actual peak temperature between 10 and 30 seconds Cool-down rate (Peak to 50 C) less than 6 C/second Time from 30 C to Peak temperature no greater than 300 seconds Temperature / C Chip-mount air reflow profile max. 260 C 217 C max. 300 s 10... 30 s 30... 150 s Time / s
Vectron International Filter specification TFS 2096 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Strehl 19.06.2007 1.1 - Change and add data Strehl 24.07.2007 1.2 - Change insertion loss and pass band variation S. Channaa 15.01.2008 1.3 - Change pass band, pass band variation, loss and OTR S. Channaa 12.02.2008 1.4 - Change attenuation and vswr - Add typical values and filter characteristic, generation of filter specification S. Channaa 30.04.2008 1.5 - Correct construction Strehl 06.06.2008 1.6 - Change input power level S. Channaa 23.03.2010 1.7 - Change Input power level S. Channaa 15.09.2010 1.8 - Maximum input power updated Kortenbeutel 04.02.2014