ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1) Plastic mallet (not provided) (1) 5/32 Hex key (provided) INSTALLATION ON LINX ORGANIZERS Flat Panel Wall Plate Accessory (Shipped with FPD Arm) #TOACAORG16 AND #TOACAORG20 1. Insert the top flange of the Bracket into the channel in the Linx organizer and then drop the bracket down to engage the hooks. See figure 1. Chann Flange Bracket Figure 1 Rev. A Date: 5/2/08 1
INSTALLATION ON LINX ORGANIZERS (cont.) 2. Slide the Bracket into the desired location. Place the Bottom Bracket over the Bracket and then push the tabs down in between the bottom channel of the organizer and the fabric panel. See figure 2. 3. Install two thumb screws into the threaded holes in the top of the Bracket. See figure 2. Turn the screws until they make contact with the rear of the organizer. Do not over tighten. Secure the Bottom Bracket with two #10-24 x 3/8 phillips pan head thread forming screws. See figure 3. 4. The can be installed at one of two locations on the Bracket. Attach the using two #10-32 x 1/2 Phillips head machine screws and two lock washers (provided) as shown in figure 3. Bottom bracket Tab Thumb bracket Fabric panel 5. Attach the Wall Plate Casting to the and tighten the set screw using the 5/32 hex key. See figure 4. Bottom Figure 2 Round hole (orient as Lock washer Wall Wall plate #10-32 x 1/2 phillips pan head #10-24 x 3/8 phillips pan head Figure 3 Figure 4 2
INSTALLATION ON TECH ORGANIZER, FOUNDATIONS AND LMS FRAMES #TOACATRPSS AND #TOACATRPDS Bracket (single standard) 6. Attach the to the Plate using the two #10-32 x 5/8 phillips flat heads screws, lock washers and #10-32 lock nuts provided. See figure 5. #10-32 x 5/8 phillips flat head screws (orient as shown) #10-32 lock nuts Lock Round Figure 5 plate * HOOK PLATE THIS SIDE plate The Brackets for single end standards come un-assembled and consist of a Plate and a Plate that can be used for either left hand or right hand applications. Determine which application is required and assemble the brackets as shown in figure 6. *Important: The Plates must be assembled to the side of the Plates that have HOOK PLATE THIS SIDE stamped into it. #10-32 x 5/16 phillips flat head machine Right Hand Assembly #10-32 x 5/16 phillips flat head machine screws Left Hand Assembly Figure 6 3
7. Insert the hooks on the back of the Bracket Assembly into the slotted standard at the desired height and push down. Tap the top of the bracket assembly with a mallet to ensure that the hooks are seated. See figure 7. Install a #10-24 x 3/8 Phillips pan head screw into the hole at the bottom of the bracket assembly and tighten securely. 8. Attach the Wall Plate Casting to the and tighten the set screw using the 5/32 hex key. See figure 8. ted standard Bracket Wall Plate #10-24 x 3/8 phillips Figure 8 Figure 7 Bracket (double standard) The Bracket for double slotted standards come un-assembled and consist of a Plate, a Plate, and a. *Important: The Plate must be assembled to the side of the Plate that has HOOK PLATE THIS SIDE stamped into it. 9. Attach the to the Plate using the two #10-32 x 5/8 phillips flat heads screws, lock washers and #10-32 lock nuts provided. See figure 9. #10-32 x 5/8 phillips flat head screws (orient as Round * HOOK PLATE THIS SIDE 10. Attach the Plate to the Plate using six #10-32 x 5/16 phillips flat head screws as shown in figure 10. Lock #10-32 lock nuts Figure 9 #10-32 x 5/16 phillips flat head machine Figure 10 4
11. Insert the hooks on the back of the Bracket Assembly into the double slotted standard at the desired height and push down. Tap the top of the bracket assembly with a mallet to ensure that the hooks are seated. See figure 11. Install two #10-24 x 3/8 phillips pan head thread forming screws into the holes at the bottom of the bracket assembly and tighten securely. 12. Attach the Wall Plate Casting to the and tighten the set screw using the 5/32 hex key. See figure 12. Double slotted Bracket Bracket Wall Plate Casting Figure 11 #10-24 x 3/8 phillips pan head screws Figure 12 5
#TOACATRP24 AND #TOACATRP30 Channel ted 13. Insert the hooks on the back of the Channel into the slotted standards at the desired height and push down. Tap the top of the channel with a mallet to ensure that the hooks are seated. See Figure 13. Install two #10-24 x 3/8 phillips pan head thread forming screws and tighten securely. 14. Attach the to the Bracket using two #10-32 x 1/2 phillips head machine screws, two #10-32 kep nuts and two lock washers (provided) as shown in figure 14. 15. Attach the Wall Plate Casting to the Wall Bracket and tighten the set screw using the 5/32 hex key. See figure 15. #10-24 x 3/8 phillips pan head Channel Figure 13 #10-32 kep (orient as Wall Plate Hole Lock washers Figure 14 #10-32 x 1/2 phillips pan head machine screws Figure 15 6
16. Insert the top flange of the Bracket into the top of the Channel as shown in figure 16. The bottom flange of the bracket will rest on the bottom of the channel. 17. Slide the Bracket to the desired location and then install two thumb screws into the threaded holes in the top of the bracket. Turn the thumb screws until they make contact with the rear of the Channel. Do not over tighten. See figure 17. Top flange Figure 16 Threaded Thumb Figure 17 7