ACDC 6 Watts HCP Series High Efficiency up to 9% xppower.com High Power Density Programmable Output Voltage (%%) Programmable (%%) Parallel Operation Fully Featured Signals & Controls Year Warranty Specification Input Input Voltage Input Frequency Input Current Inrush Current Power Factor Earth Leakage Current 6 VAC (77 VDC), see derating curves 76 Hz 6 W: 7. A/. A typical, W: A/ A typical, W: 8 A/9 A typical, W: 6 A/8 A typical at / VAC 6/ W: 7 A/ A typical W: A/ A typical W: A/ A typical at / VAC.99/.98, typical at / VAC full load <. ma ( kw: <. ma) at VAC/ Hz Output Output Voltage See model table Output Trim ±.% by potentiometer Output Voltage Program % of rated output (see app. notes) Program % of rated output (see app. notes) Initial Set Accuracy ±% Minimum Load No minimum load required Start Up Delay 6 W/ W: ms max. W/ W: s max. Start Up Rise Time 6 W: ms max. at full load W: ms max. at full load W/ W: ms max. at full load Hold Up Time 6 ms ( W: ms) typ. at VAC and full load Line Regulation ±.% Load Regulation V: ±.%, V standby output: ±% Transient Response <% for a % step load change Ripple & Noise mv pkpk all voltages (see note ) Overvoltage Protection Tracks output voltage. % of set voltage. Recycle AC to reset Overtemperature Auto recovery Protection Overload Protection % of output power. Constant power to 7% of set output voltage then output shuts down, recycle AC to reset Short Circuit Protection Output latches off, recycle AC to reset Temp. Coefficient ±.%/ C ( C) Remote Sense Compensates for. V max voltage drop. (see app. notes) Enable Output must be enabled (see app. notes) Current Share supplies can share within % Standby Output See model table General Efficiency See model table Isolation VAC Input to Output, VAC Input to Ground, VDC Output to Ground Isolation Resistance M / VDC Switching Frequency PFC khz typical, PWM 6 khz typical Power Density 6 W: 8. W/in W:. W/in W/ W:.8 W/in Signals & Controls See app. notes MTBF 6 W: khrs, W: khrs, W/ W: khrs to MILHDBK7F at C, GB Environmental Operating Temperature C to C, see derating curves Cooling Internal fan fitted. Speed increases with load and internal temperature Operating Humidity % R.H. noncondensing Storage Temperature C to 8 C Storage Humidity 9% R.H. Vibration Hz, g min/cycle, min period for each axis. Compliant to IEC686, IEC 686 EMC & Safety Emissions EN class B conducted & radiated Harmonic Currents class A, 6 & W: class C for loads %, W: class C for loads %, W: class C for loads % Voltage Flicker ESD Immunity, ± kv contact, ±8 kv air discharge, Perf Criteria A Radiated Immunity, V/m, Perf Criteria A EFT/Burst, level, Perf Criteria A Surge, installation class, Perf Criteria A Conducted Immunity 6, Perf Criteria A Magnetic Field 8, Perf Criteria A Dips & Interruptions, % ms, % ms, >9% ms, Perf Criteria A, B, B Safety Approvals UL9, EN9 (all models) A C. No. 9 (6 W/ W only)
Models and Ratings HCP6 Output Power Output Voltage V Min Max Standby Output () Efficiency () Model Number W. VDC. A. A V/. A 8% HCP6PS W. VDC. A. A V/. A 88% HCP6PS W. VDC. A. A V/. A 88% HCP6PS 6 W. VDC. A 7. A V/. A % HCP6PS 6 W 7. VDC. A. A V/. A % HCP6PS7 6 W 8. VDC. A.6 A V/. A 9% HCP6PS8 ACDC. Ripple & noise is measured with MHz bandwidth and using twisted pairwire terminated with. µf & 7 µf capacitors in parallel.. Measured with VAC input and full load.. Present whenever AC is applied. Mechanical Details.6 (.9) 9. (9.) V. (7.) 6 CN9 LED V M6 Voltage Adj. M Max Length = mm Airflow.9 (7.). (6.) E N L. (.) 7. (98.).6 (7.).6 (6.9).8 (.) M (Both sides) Max Length = 6 mm.98 (.). (.) 8.7 (.). (8.). All dimensions are in inches (mm).. Weight. lb (.8 kg). Signals mating connector: PHDR6VS housing, SPHDTP contacts Derating Curve Thermal Derating Curve Control Pin Connections Pin Function Description Pin Function Description Remote Sense () 9 Enable ON/OFF () Local Sense () Signal Ground Remote Sense () PWM (POK) PWM is Switching Local Sense () Signal Ground V SB (Aux) V Standby Output () VCI V Program 6 V SB (Aux) V Standby Output () Signal Ground 7 Enable ON/OFF () Current Share 8 Signal Ground 6 ACI I Program Input Derating Curve 7 7 6 Input Voltage (VAC)
ACDC Models and Ratings HCP Output Power Output Voltage V Min Max Standby Output () Efficiency () Model Number 7 W. VDC. A 6. A V/. A 87% HCPPS 7 W. VDC. A. A V/. A 88% HCPPS 9 W. VDC. A. A V/. A 89% HCPPS W 7. VDC. A 7. A V/. A 89% HCPPS7 W 8. VDC. A. A V/. A % HCPPS8. Ripple & noise are measured with MHz bandwidth and using twisted pairwire terminated with. µf & 7 µf capacitors in parallel.. Measured with VAC input and full load.. Present whenever AC is applied. Mechanical Details.6 (.9). (8.) V. (7.) 6 CN9 LED V. (6.7) E N M6 Voltage Adj. M Max Length = mm Airflow.9 (7.) L. (.) 8.8 (.).77 (.). (6.7).8 (.) M (Both sides) Max Length = 6 mm.98 (.). (.). (.). (8.). All dimensions are in inches (mm).. Weight.6 lb (. kg). Signals mating connector: PHDR6VS housing, SPHDTP contacts Control Pin Connections Pin Function Description Pin Function Description Remote Sense () 9 Enable ON/OFF () Local Sense () Signal Ground Remote Sense () PWM (POK) PWM is Switching Local Sense () Signal Ground V SB (Aux) V Standby Output () VCI V Program 6 V SB (Aux) V Standby Output () Signal Ground 7 Enable ON/OFF () Current Share 8 Signal Ground 6 ACI I Program Derating Curve Thermal Derating Curve Input Derating Curve 7 7 6 Input Voltage (VAC)
Models and Ratings HCP Output Power Output Voltage V Min Max Standby Output () Efficiency () Model Number W. VDC. A. A V/. A 87% HCPPS W. VDC. A. A V/. A 88% HCPPS W. VDC. A 6. A V/. A 89% HCPPS W 7. VDC. A. A V/. A 89% HCPPS7 W 8. VDC. A. A V/. A % HCPPS8 ACDC. Ripple & noise are measured with MHz bandwidth and using twisted pairwire terminated with. µf & 7 µf capacitors in parallel.. Measured with VAC input and full load.. Present whenever AC is applied. Mechanical Details.9 (.) 9.8 (.). (6.).7 (.). (.7) V M, Max Length = mm V.86 (98.) Airflow Voltage Adj. 9 8 7 6. (7.) L N E. (.6).8 (.). (.) 9. (7.) Ø. (Ø 8.) M, Max Length = mm.7 (.). All dimensions are in inches (mm).. Weight 7. lb (. kg). Signals mating connector is Dinkle ECVP or equivalent. Wire gauge 8 AWG. Control Pin Connections Pin Function Description Pin Function Description Remote Sense () 6 Signal Ground Remote Sense () 7 PWM (POK) PWM is Switching V SB (Aux) V Standby Output () 8 VCI V Program Enable () 9 ACI I Program Enable () Current Share Thermal Derating Curve For HCPPS/ For HCPPS/7/8 VAC VAC VAC VAC > VAC VAC VAC VAC VAC > VAC 7
ACDC Models and Ratings HCP Output Power Output Voltage V Min Max Standby Output () Efficiency () Model Number W. VDC. A. A V/. A 87% HCPPS W. VDC. A. A V/. A 88% HCPPS W. VDC. A. A V/. A 89% HCPPS W 7. VDC. A. A V/. A 89% HCPPS7 W 8. VDC. A 6. A V/. A % HCPPS8. Ripple & noise are measured with MHz bandwidth and using twisted pairwire terminated with. µf & 7 µf capacitors in parallel.. Measured with VAC input and full load.. Present whenever AC is applied. Mechanical Details. (.8).6 (.) 9.8 (.). (7.) V.86 (98.) M, Max Length = mm Airflow V Voltage Adj. 9 8 7 6. (7.). (.7) E N L.6 (7.). (.8). (.). (6.).6 (9.) M, Max Length = mm Ø. (Ø8.). (.).9 (.). All dimensions are in inches (mm).. Weight.6 lb (6.6 kg). Signals connector is Dinkle ECVP or equivalent. Wire gauge 8 AWG. Derating Curve Control Pin Connections Pin Function Description Pin Function Description Local Sense () 7 Enable () Remote Sense () 8 Signal Ground Remote Sense () 9 PWM (POK) PWM is Switching Local Sense () VCI V Program V SB () V Standby Output() ACI I Program 6 Enable () Current Share For HCPPS/ For HCPPS/7/8 VAC VAC VAC VAC > VAC 7 VAC VAC VAC VAC > VAC 7
Application Remote Enable (unit supplied enabled) HCP Series ACDC V SB V SB KΩ SW KΩ V V Low/H OFF Power OFF Low Power OFF ON Power ON High Power ON (A) Using internal V standby (B) Using external by transistor PWM Signal Remote Sense Local Sense POWER SUPPLY V Standby PWM R PWM NOT SWITCHING (HIGH) PWM SWITCHING (LOW) Load Load Signal Connector Must be used if remote sense is not required. LED Status LED Status Solid (Green) Slow Blink (Green) Fast Blink (Red) Solid (Red) Slow Blink (Red) Intermittent Blink (Red) Short & Long Blink (Red) Output Status DC Output OK Output Not Enabled Over Voltage Over Loaded Short Circuited Under Voltage (<7% of output voltage) Over Temperature Fan Fail V Standby Failure
ACDC Application Output Voltage Program O utput V oltage (% ) 7 Output Voltage (%) 8 7 HCP Series....... External Voltage (VDC) All models..8.6 6 Open External Resistor (kω) HCP6/ Pin VCI Pin Pin VCI Pin..8 V.6 kω 6 kω Output Voltage (%) 7 Output Voltage (%) 8 7 6.6 6.9 9.8 7 6 Open External Resistor (kω) HCP. 8.6 9 7 Open External Resistor (kω) HCP Pin VCI Pin Pin VCI Pin 6.6 kω 6 kω. kω kω Program (%) 7 (%) 8 7.6........ External Voltage (VDC) All models.6 6 Open External Resistor (kω) HCP6/ Pin ACI Pin Pin ACI Pin.6. V. kω kω
Application Program HCP Series ACDC (%) (%).7. 9. 6 Open External Resistor (kω) HCP.9.. Open External Resistor (kω) HCP Pin ACI Pin Pin ACI Pin.7 kω 6 kω.9 kω kω Current Sharing with Remote Sensing Load Current Sharing with Local Sensing In parallel operation, it is possible that only one unit will operate if the load is less than % of the combined rated output load. It is possible to have more than five units in parallel, contact sales for details. Feb