TECHNICAL DATA SHEET FOR Single Mode Optical Fibre Cable Direct Burial Application (SM 12 Fibers) Product: Single Mode Optical Fiber Cable Customer: Date: Write by: Kevin Zhou / technical engineer International Business Dept. TONGDING GROUP JIANGSU TONGDING OPTIC-ELECTRONIC STOCK CO., LTD. Add: No.18 Xiaoping Rd., Badu Industrial Zone, Wujiang City, Jiangsu Province China 215233 Tel: 0086-512-63873510, Fax: 0086-512-63873512 Webpage: http://www.tdgd.com.cn, E-mail: tongdingchina@yahoo.cn Page 1 of 6
1. Cable Construction 1.1 Cable cross-section Loose tube Optical fiber Filling gel Filling compound Steel wire Filler rod Inner sheath Filling compound Steel tape Outer sheath 2. Cable Specification 2.1 Sheath marking TDGD TDGD 2010 GYTY53 12B1.3 (G.652.D) =XXXXm : Manufacturer s brand 2010 : Manufacture year GYTY53 : Cable type 12B1.3 (G.652.D) : 12 cores single-mode optical fiber (ITU-T Rec. G.652.D) =XXXXm *The marking is printed every 1 meter; : Mark of meters ** G.652D means ITU-T Rec. Low Water Peak (LWP) G.652 single mode optical fiber. 2.2 The color of marking is white, but if the remarking is necessary, the yellow color marking shall be printed newly on a different position. 2.3 An occasional unclear of length marking is permitted if both of the neighboring markings are clear; 2.4 The both cable ends are sealed with heat shrinkable end caps to prevent water ingress. Page 2 of 6
2.5 Fiber color code No 1 2 3 4 5 6 Color Blue Orange Green Brown Slate White No 7 8 9 10 11 12 Color Red Black Yellow Violet Pink Aqua 2.6 Color codes for Loose Tube (LT) & Filler Rod (FR) Fiber Element no. number 1 2 3 4 5 6 12 LT LT FR FR FR FR 2.7 Cable structure and parameter Fiber number Max. fiber number per tube Total unit number (LT + FR) I / O sheath thickness (nominal*) Overall diameter (nominal**) Weight (approx.) mm mm kg/km 12 6 6 (2LT + 4FR) 1.0 / 1.8 12.7 170 * The nominal sheath thickness may vary by 0.2mm. ** The nominal outer diameter and height may vary by 0.2mm. Page 3 of 6
3. Fiber Properties 3.1 The properties of single mode optical fiber (ITU-T Rec. G.652.D) Item Specification Fiber type Fiber material Attenuation coefficient @ 1310 nm @ 1383 nm @ 1550 nm @ 1625 nm Point discontinuity Cable cut-off wavelength Zero-dispersion wavelength Zero-dispersion slope Single mode Doped silica 0.36 db/km 0.32 db/km 0.22 db/km 0.30 db/km 0.05 db 1260 nm 1300 ~ 1324 nm 0.093 ps/(nm 2.km) Chromatic dispersion @ 1288 ~ 1339 nm 3.5 ps/(nm. km) @ 1271 ~ 1360 nm 5.3 ps/(nm. km) @ 1550 nm 18 ps/(nm. km) @ 1625 nm 22 ps/(nm. km) PMD Q (Quadrature average*) 0.2 ps/km 1/2 Mode field diameter @ 1310 nm Core / Clad concentricity error Cladding diameter Cladding non-circularity Primary coating diameter 9.2±0.4 um 0.5 um 125.0 0.7 um 1.0% 245 10 um Proof test level 100 kpsi (=0.69 Gpa), 1% Temperature dependence 0 o C~ +70 o C @ 1310 & 1550nm 0.1 db/km * PMD Q is a link of 20 cable sections (M) and a probability level of 0.01% (Q). 4. Characteristic of Optical Cable 4.1 Mechanical & environmental characteristics 4.1.1 Cable bending radius: 10 x cable diameter (during operation) 4.1.2 Temperature range Operating temperature range Storage / Transport temperature range Installation temperature range 20 x cable diameter (during installation) -40 o C to +60 o C -50 o C to +70 o C -20 o C to +50 o C Page 4 of 6
4.2 Main mechanical & environmental characteristics test NO ITEM TEST METHOD ACCEPTANCE REQUIREMENTS 1 Tensile Strength IEC 794-1-E1 - Load: 3, 000 N - Length of cable under load: 50m 2 Crush Test IEC 60794-1-E3 3 Impact Test IEC 60794-1-E4 - Load: 3, 000 N/100mm - Load time: 1min - Points of impact: 5 - Times of per point: 5 - Impact energy: 10.0Nm - Radius of hammer head: 12.5mm - Impact rate: 2sec/cycle 4 Repeated Bending IEC 60794-1-E6 - Bending Dia.: 20 x OD - Load: 250N - Flexing rate: 3sec/cycle - No. of cycle: 30 5 Torsion IEC 60794-1-E7 - Length: 1m - Load: 250N - Twist rate: 1min/cycle - Twist angle: ±90 - No. of cycle: 10 6 Water Penetration IEC 60794-1-F5B - Height of water: 1m - Sample length: 3 m - Time: 24 hour - No water shall have leaked from the opposite end of cable 7 Temperature Cycling IEC 60794-1-F1 - Temperature step: +20 o C -40 o C +60 o C +20 o C - Time per each step: 24 hrs - Number of cycle: 2 8 Compound Flow IEC 60794-1-E14 - Sample length: 30 cm - Temp: 70 C 2 C - Time: 24 hours - No compound flow 9 Sheath High Voltage Test - On line test - 9t KV (t-sheath thickness) - No sheath breakdown Page 5 of 6
5. Packing and Marking 5.1 Packing 5.1.1 Each single length of cable shall be reeled on Fumigated Wooden Drum suitable for long distance shipment. 5.1.2 Covered by plastic buffer sheet. 5.1.3 Sealed by strong wooden battens. 5.1.4 At least 1 m of inside end of cable will be reserved for testing. 5.1.5 Drum length 5.1.5.1 Standard drum length is 2000m±3%; 5.1.5.2 Single length not less than 95% of standard length per drum shall be permitted for quantity not exceeding 10% of the total supply; 5.1.5.3 Total quantity is at least the ordered quantity. 5.2. Drum Marking 5.2.1 Cable drum - Manufacturer brand; - Roll-direction arrow; - Cable outer end position indicating arrow; - The word OPTICAL FIBER CABLE ; - Origin, The word MADE IN CHINA ; - Caution plate indicating the correct method for loading, unloading and convey the cable; - Other customer information such as contract no., project no., and delivery destination. (if needed) 5.2.2 Marking plate - Product name; - Cable type and size; - Drum length; - Gross / Net weight in kilograms; - Drum number in meters; - Manufacturer's name; - Manufacturing year and month; - Project number, contract number or purchasing order number (if needed). 5.3 Cable identification documents - Test report. -----------End---------- Page 6 of 6