Form Rev- /5/ Shielded Power Inductors TLSG Series FEATURES Low DCR and excellent current handling Operating temperature range: C to +5 C with Irms current, +5 C to +5 C with derated current Storage temperature range: C to +5 C Specifications(5 C): Part Number Inductance DCR SRF Isat(A) Irms(A) ±% (mω ) Typ % C C (uh) Nom Max (MHz) drop rise rise ⁴ TLSG -RM_..5.5 5 9.. 55.5 TLSG -R5M_.5.5.7 7.5. 5. TLSG -RM_..7.9 5... TLSG - RM_... 55...5 TLSG -R5M_.5..7...5 TLSG -RM_..55...5. TLSG -RM_..7. 7.. 5. TLSG -R7M_.7 5. 5.7 9 5. 7.5. TLSG -5RM_ 5...9. 5.7. TLSG -RM_...9...5 TLSG -RM_..7.9..9 7. TLSG -M_..75 7.5.5 5.5 TLSG -5M_ 5.9. 9 5.5 9.9. Tolerance - M= ± % Notes. TLSG-R5MD (For part numbering details see note 5 below). Inductance tested at KHz,.Vrms.. Isat is a DC current at which the inductance drops the specified amount from its original value with no current. Irms is a current that causes the specified temperature rise from 5 C ambient. 5. Part numbering: TLTLSG-R5MCSG-R5MD TL- Inductor code, - Series code, SG- SMD Green, R5 -.5 µh, M - Tolerance = ±%, D - " reel Packaging: B= Less than full reel machine ready D= machine ready. EIA-embossed plastic tape ( parts) Termination: Matte tin over nickel over phospher bronze SCOTT BLVD SANTA CLARA, CA 955 TLSG Rev. - 9//5 of 5 TEL: () 7-7 FAX: () 9-555
XXX Form Rev- /5/ Shielded Power Inductors TLSG Series Marking : "XXX" means the Inductance in uh Example : R means.uh R5 is.5uh Dimensions : (inch/mm) Dash number.9 ±., ±,5.,7 typ.7±., ±, Dimensions are in inches mm.5 ±., ±,5.9, max A (see table).75 ±.,5 ±,5 A ±. in ±, mm Dash B number (in / mm) (in / mm) -R.9 /.5 /. -R5.9 /.5 /. -R.9 /.5 /. -R.9 /.5 /. -R5. / 9.. /.7 -R.7 / 9..9 /. -R.5 / 9..7 / 9.5 -R7.5 / 9..7 / 9.5-5R.5 / 9..7 / 9.5 -R. /.. / 9. -R.5 /.5.5 /.9 -.5 /.5.5 /.9-5.5 /.5.5 /.9 B (see table).9,.,5 Recommended Land Pattern Percent of rated I rms.. Frequency (MHz) 9 7 5 - - Ambient temperature ( C) 5 C 5 µh µh. µh.7 µh. µh.5 µh. µh. µh.5 µh. µh SCOTT BLVD SANTA CLARA, CA 955 TLSG Rev. - 9//5 of 5 TEL: () 7-7 FAX: () 9-555
Form Rev- /5/ Shielded Power Inductors TLSG Series..... µh 5 7 9..5...5 µh.. 5 7 9..... µh.. 5 7...... µh... 5 7....5 µh.. 5..5..5.. µh.5..5 5 5. µh 5 5 5 5 5 5 5 5.7 µh 5 5 5 5 5 5. µh 5 5 5. µh 5 5 5 SCOTT BLVD SANTA CLARA, CA 955 TLSG Rev. - 9//5 of 5 TEL: () 7-7 FAX: () 9-555
Form Rev- /5/ Shielded Power Inductors TLSG Series. µh 5 µh µh Reflow Profile ( C) 5 7 Time within 5 C of peak temperature ( seconds) Ramp-Up C/sec max Ramp-Down C /sec max Peak temperature 55 C Temperature 5 Preheat / Soak ( seconds) Reflow Time above 7 C ( 5 seconds) 5 9 5 7 Time (seconds) SCOTT BLVD SANTA CLARA, CA 955 TLSG Rev. - 9//5 Page of 5 TEL: () 7-7 FAX: () 9-555
Form Rev- /5/ Shielded Power Inductors TL SG Series Reliability Test Test Items Low temperature storage High temperature storage Thermal shock Humidity resistance Drop Vibration Terminal strength Soldering heat resistance Test Conditions Criteria Placed at - C for 5 hours, then Inductance shall be within ±% of the measured at room ambient temperature after placing hours. Placed at +5 C for 5 hours, then Inductance shall be within ±% of the measured at room ambient temperature after placing hours. - C, min ~ +5 C, min, 5hours. Inductance shall be within ±% of the Placed at 9 to 95%RH, +5 C for 5 Inductance shall be within ±% of the hours, then measured at room ambient temperature after placing hours. Insulation resistance>mohm at DC Drop specimen three times on concrete Inductance shall be within ±% of the floor from a height of meter which mounted on test board. Frequency : ~ 5Hz Inductance shall be within ±% of the Amplitude :.5mm or G Sweep time : oct/min Test Directions : X,Y,Z Test Time : hours each direction Add static load.9n(5gf) to inductor No detachment of terminal pin and no through hole of test board for ± sec. breakage of wire. Dip inductor's terminal in solder bath of Inductance shall be within ±% of the following conditions: ) ±5 C, ±sec, Appearance : No damage ) 5± C,.5±.5sec SCOTT BLVD SANTA CLARA, CA 955 TLSG Rev. - 9//5 Page 5 of 5 TEL: () 7-7 FAX: () 9-555