Preferred Device Sensitive Gte Trics Silicon Bidirectionl Thyristors Designed primrily for full wve AC control pplictions, such s light dimmers, motor controls, heting controls nd power supplies; or wherever full wve silicon gte controlled solid stte devices re needed. Tric type thyristors switch from blocking to conducting stte for either polrity of pplied node voltge with positive or negtive gte triggering. Fetures Sensitive Gte Triggering Uniquely Comptible for Direct Coupling to TTL, HTL, CMOS nd Opertionl Amplifier Integrted Circuit Logic Functions Gte Triggering: 4 Mode 2N6071A, B; 2N6073A, B; 2N6075A, B Blocking Voltges to 600 V All Diffused nd Glss Pssivted Junctions for Greter Prmeter Uniformity nd Stbility Smll, Rugged, Thermopd Construction for Low Therml Resistnce, High Het Dissiption nd Durbility Device Mrking: Device Type, e.g., 2N6071A, Dte Code MT2 TRIACS A RMS, 200 600 V 3 2 1 G REAR VIEW SHOW TAB CASE 077 STYLE 5 MARKING DIAGRAM 1. Cthode 2. Anode 3. Gte YWW 2N 607xyG x = 1, 3, 5 y = A, B Y = Yer WW = Work Week G = PbFree Pckge ORDERING INFORMATION See detiled ordering nd shipping informtion in the pckge dimensions section on pge 7 of this dt sheet. Preferred devices re recommended choices for future use nd best overll vlue. *For dditionl informtion on our PbFree strtegy nd soldering detils, plese downlod the ON Semiconductor Soldering nd Mounting Techniques Reference Mnul, SOLDERRM/D. Semiconductor Components Industries, LLC, 2008 Mrch, 2008 Rev. 8 1 Publiction Order Number: 2N6071/D
MAXIMUM RATINGS (T J = 25 C unless otherwise noted) Rting Symbol Vlue Unit *Pek Repetitive Off Stte Voltge (Note 1) (T J = 40 to 110 C, Sine Wve, 50 to 60 Hz, Gte Open) 2N6071A,B 2N6073A,B 2N6075A,B V DRM, V RRM 200 400 600 *On Stte RMS Current (T C = 85 C) Full Cycle Sine Wve 50 to 60 Hz I T(RMS) A *Pek Nonrepetitive Surge Current (One Full cycle, 60 Hz, T J = +110 C) I TSM 30 A Circuit Fusing Considertions (t = 8.3 ms) I 2 t 3.7 A 2 s *Pek Gte Power (Pulse Width s, T C = 85 C) P GM 10 W *Averge Gte Power (t = 8.3 ms, T C = 85 C) P G(AV) W *Pek Gte Voltge (Pulse Width s, T C = 85 C) V GM 5.0 V *Operting Junction Temperture Rnge T J 40 to +110 C *Storge Temperture Rnge T stg 40 to +150 C Mounting Torque (6 32 Screw) (Note 2) 8.0 in. lb. Stresses exceeding Mximum Rtings my dmge the device. Mximum Rtings re stress rtings only. Functionl opertion bove the Recommended Operting Conditions is not implied. Extended exposure to stresses bove the Recommended Operting Conditions my ffect device relibility. 1. V DRM nd V RRM for ll types cn be pplied on continuous bsis. Blocking voltges shll not be tested with constnt current source such tht the voltge rtings of the devices re exceeded. 2. Torque rting pplies with use of compression wsher. Mounting torque in excess of 6 in. lb. does not pprecibly lower cse to sink therml resistnce. Min terminl 2 nd hetsink contct pd re common. THERMAL CHARACTERISTICS Chrcteristic Symbol Mx Unit *Therml Resistnce, JunctiontoCse R JC 3.5 C/W Therml Resistnce, JunctiontoAmbient R JA 75 C/W Mximum Led Temperture for Soldering Purposes 1/8 from Cse for 10 Seconds T L 260 C *Indictes JEDEC Registered Dt. V 2
ELECTRICAL CHARACTERISTICS (T C = 25 C unless otherwise noted; Electricls pply in both directions) Chrcteristic Symbol Min Typ Mx Unit OFF CHARACTERISTICS *Pek Repetitive Blocking Current (V D = V DRM = V RRM; Gte Open) T J = 25 C T J = 110 C I DRM, I RRM ON CHARACTERISTICS *Pek On Stte Voltge (Note 3) (I TM = 6.0 A Pek) V TM 2 V *Gte Trigger Voltge (Continuous DC), All Qudrnts (Min Terminl Voltge = 12 Vdc, R L = 100, T J = 40 C) Gte NonTrigger Voltge, All Qudrnts (Min Terminl Voltge = 12 Vdc, R L = 100, T J = 110 C) *Holding Current (Min Terminl Voltge = 12 Vdc, Gte Open, Inititing Current = 1 Adc) T J = 40 C T J = 25 C 10 2 V GT 1.4 2.5 V GD 0.2 Turn On Time (I TM = 14 Adc, I GT = 100 dc) t gt 1.5 s I H 30 15 QUADRANT (Mximum Vlue) A V V Gte Trigger Current (Continuous DC) (Min Terminl Voltge = 12 Vdc, R L = 100 ) DYNAMIC CHARACTERISTICS Criticl Rte of Rise of Commuttion Voltge @ V DRM, T J = 85 C, Gte Open, I TM = 5.7 A, Exponentil Wveform, Commutting di/dt = A/ms 3. Pulse Test: Pulse Width ms, Duty Cycle 2%. *Indictes JEDEC Registered Dt. Type I GT @ T J I 2N6071A 2N6073A 2N6075A 2N6071B 2N6073B 2N6075B II III IV +25 C 5 5 5 10 40 C 20 20 20 30 +25 C 3 3 3 5 40 C 15 15 15 20 dv/dt(c) 5 V/ s SAMPLE APPLICATION: TTL SENSITIVE GATE 4 AMPERE TRIAC TRIGGERS IN MODES II AND III 14 0 V MC7400 4 V EE 7 V EE = 5.0 V + 510 2N6071A LOAD 115 VAC 60 Hz Trigger devices re recommended for gting on Trics. They provide: 1. Consistent predictble turn on points. 2. Simplified circuitry. 3. Fst turn on time for cooler, more efficient nd relible opertion. 3
Voltge Current Chrcteristic of Trics (Bidirectionl Device) + Current Symbol V DRM I DRM V RRM I RRM V TM I H Prmeter Pek Repetitive Forwrd Off Stte Voltge Pek Forwrd Blocking Current Pek Repetitive Reverse Off Stte Voltge Pek Reverse Blocking Current Mximum On Stte Voltge Holding Current I RRM t V RRM on stte I H I H V TM off stte Qudrnt 1 MinTerminl 2 + + Voltge I DRM t V DRM Qudrnt 3 MinTerminl 2 V TM Qudrnt Definitions for Tric MT2 POSITIVE (Positive Hlf Cycle) + (+) MT2 (+) MT2 Qudrnt II () I GT GATE (+) I GT GATE Qudrnt I REF REF I GT + I GT () MT2 () MT2 Qudrnt III () I GT GATE (+) I GT GATE Qudrnt IV REF REF MT2 NEGATIVE (Negtive Hlf Cycle) All polrities re referenced to. With inphse signls (using stndrd AC lines) qudrnts I nd III re used. SENSITIVE GATE LOGIC REFERENCE Firing Qudrnt IC Logic Functions I II III IV TTL 2N6071A Series 2N6071A Series HTL 2N6071A Series 2N6071A Series CMOS (NAND) 2N6071B Series 2N6071B Series CMOS (Buffer) 2N6071B Series 2N6071B Series Opertionl Amplifier 2N6071A Series 2N6071A Series Zero Voltge Switch 2N6071A Series 2N6071A Series 4
T C, CASE TEMPERATURE ( C) 110 100 90 80 α α = 30 60 90 120 180 dc T C, CASE TEMPERATURE ( C) 110 100 90 80 α = 30 60 120 180 dc 90 α = CONDUCTION ANGLE 70 0 I T(AV), AVERAGE ON STATE CURRENT (AMP) α = CONDUCTION ANGLE 70 0 I T(RMS), RMS ON STATE CURRENT (AMP) Figure 1. Averge Current Derting Figure 2. RMS Current Derting P (AV), AVERAGE POWER (WATTS) 8.0 6.0 α = CONDUCTION ANGLE α = 30 60 90 120 180 dc P (AV), AVERAGE POWER (WATTS) 8.0 6.0 α = CONDUCTION ANGLE 120 α = 180 90 60 dc 30 0 0 0 0 I T(AV), AVERAGE ON STATE CURRENT (AMP) Figure 3. Power Dissiption I T(RMS), RMS ON STATE CURRENT (AMP) Figure 4. Power Dissiption, GATE TRIGGER VOLTAGE (NORMALIZED) VGT OFF STATE VOLTAGE = 12 Vdc ALL MODES 0.7 60 40 20 0 20 40 60 80 T J, JUNCTION TEMPERATURE ( C) 100 Figure 5. Typicl GteTrigger Voltge 120 140, GATE TRIGGER CURRENT (NORMALIZED) IGT 0.7 OFF STATE VOLTAGE = 12 Vdc ALL MODES 60 40 20 0 20 40 60 80 100 120 140 T J, JUNCTION TEMPERATURE ( C) Figure 6. Typicl GteTrigger Current 5
ITM, ON STATE CURRENT (AMP) 40 30 20 10 7.0 5.0 T J = 110 C T J = 25 C IH, HOLDING CURRENT (NORMALIZED) 0.7 60 40 20 0 20 40 60 80 100 120 140 T J, JUNCTION TEMPERATURE ( C) GATE OPEN APPLIES TO EITHER DIRECTION Figure 8. Typicl Holding Current 0.7 0.2 0.1 0 5.0 V TM, ON STATE VOLTAGE (VOLTS) PEAK SINE WAVE CURRENT (AMP) 34 32 30 28 26 24 22 T J = 40 to +110 C f = 60 Hz 20 18 16 14 5.0 7.0 10 NUMBER OF FULL CYCLES Figure 7. Mximum OnStte Chrcteristics Figure 9. Mximum Allowble Surge Current ZθJC(t), TRANSIENT THERMAL IMPEDANCE ( C/W) 10 5.0 MAXIMUM TYPICAL 0.2 0.1 0.1 0.2 5.0 10 20 50 100 200 500 k k 5.0 k 10 k t, TIME (ms) Figure 10. Therml Response 6
ORDERING INFORMATION 2N6071A 2N6071AG Device Pckge Shipping (PbFree) 500 Units / Box 2N6071AT 50 Units / Tube 2000 Units / Box 2N6071ATG 2N6071B 2N6071BG (PbFree) (PbFree) 50 Units / Tube 2000 Units / Box 500 Units / Box 2N6071BT 50 Units / Tube 2000 Units / Box 2N6071BTG 2N6073A 2N6073AG 2N6073B 2N6073BG 2N6075A 2N6075AG (PbFree) (PbFree) (PbFree) (PbFree) 50 Units / Tube 2000 Units / Box 500 Units / Box 2N6075B 2N6075BG (PbFree) For informtion on tpe nd reel specifictions, including prt orienttion nd tpe sizes, plese refer to our Tpe nd Reel Pckging Specifictions Brochure, BRD8011/D. 7
PACKAGE DIMENSIONS H Q 1 2 3 F B U A K V G S D 2 PL M C J R 0.25 (0.010) M A M B M 0.25 (0.010) M A M B M CASE 7709 ISSUE Z NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 07701 THRU 08 OBSOLETE, NEW STANDARD 07709. INCHES MILLIMETERS DIM MIN MAX MIN MAX A 0.425 0.435 10.80 14 B 0.295 05 7.50 7.74 C 0.095 0.105 2.42 2.66 D 0.020 0.026 1 0.66 F 0.115 0.130 2.93 3.30 G 0.094 BSC 2.39 BSC H 0.050 0.095 1.27 2.41 J 0.015 0.025 9 0.63 K 75 0.655 14.61 16.63 M 5 TYP 5 TYP Q 0.148 0.158 3.76 1 R 0.045 0.065 1.15 1.65 S 0.025 0.035 0.64 0.88 U 0.145 0.155 3.69 3.93 V 0.040 2 STYLE 5: PIN 1. MT 1 2. MT 2 3. GATE ON Semiconductor nd re registered trdemrks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to mke chnges without further notice to ny products herein. SCILLC mkes no wrrnty, representtion or gurntee regrding the suitbility of its products for ny prticulr purpose, nor does SCILLC ssume ny libility rising out of the ppliction or use of ny product or circuit, nd specificlly disclims ny nd ll libility, including without limittion specil, consequentil or incidentl dmges. Typicl prmeters which my be provided in SCILLC dt sheets nd/or specifictions cn nd do vry in different pplictions nd ctul performnce my vry over time. All operting prmeters, including Typicls must be vlidted for ech customer ppliction by customer's technicl experts. SCILLC does not convey ny license under its ptent rights nor the rights of others. SCILLC products re not designed, intended, or uthorized for use s components in systems intended for surgicl implnt into the body, or other pplictions intended to support or sustin life, or for ny other ppliction in which the filure of the SCILLC product could crete sitution where personl injury or deth my occur. Should Buyer purchse or use SCILLC products for ny such unintended or unuthorized ppliction, Buyer shll indemnify nd hold SCILLC nd its officers, employees, subsidiries, ffilites, nd distributors hrmless ginst ll clims, costs, dmges, nd expenses, nd resonble ttorney fees rising out of, directly or indirectly, ny clim of personl injury or deth ssocited with such unintended or unuthorized use, even if such clim lleges tht SCILLC ws negligent regrding the design or mnufcture of the prt. SCILLC is n Equl Opportunity/Affirmtive Action Employer. This literture is subject to ll pplicble copyright lws nd is not for resle in ny mnner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literture Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colordo 80217 USA Phone: 3036752175 or 8003443860 Toll Free USA/Cnd Fx: 3036752176 or 8003443867 Toll Free USA/Cnd Emil: orderlit@onsemi.com N. Americn Technicl Support: 8002829855 Toll Free USA/Cnd Europe, Middle Est nd Afric Technicl Support: Phone: 421 33 790 2910 Jpn Customer Focus Center Phone: 81357733850 8 ON Semiconductor Website: www.onsemi.com Order Literture: http://www.onsemi.com/orderlit For dditionl informtion, plese contct your locl Sles Representtive 2N6071/D