WILSHIRE BED Bed Assembly Instructions. Shorter Canopy Rail Left & Right Head Board Posts Longer Canopy Rail Head Board Panel Metal Pin Slat Support Left & Right Foot Board Posts Slats Foot Board Panel Leg Supports Side Rail HEAVY WORK!! 2 or more people required to perform this exercise Page 1of 5
Hardware.(Packed Hardware in Box Pack #1) In Box # 3 Parts (box # 1) M6 x 120 mm Bolt 8 pcs M4x 32 mm Screw 26 pcs M8 x 20mm Bolt 8 pcs - Head Board Post Left & Right, 2 pcs. (HBL & HBR) - Foot Board Post Left & Right, 2 pcs. (FBL & FBR) W I L S H I R E B E D A S S E M B L Y I N S T R U C T I O N S M6 x 70 mm Bolt bolt 4 pcs Washer 8 pcs Parts (box # 3) - Side Rail, 2 pcs. - Slat Support, 1 pc. - Longer Canopy Rail, 2pcs. - Shorter Canopy Rail, 2pcs. - Leg Support, 4pcs. M6 Barrel Nut 8 pcs 4mm Allen Key 1 pc Dia.10mm x 40mm Wood Dowel 12 pcs. 5mm Allen Key 1 pc Dia. 8mm x 65mm Metal Pin 4 pcs. Parts (Slats Box) - Slat with center hole, 4 pcs. - Slat without center hole, 9 pcs. HBR Head Board Post Right Head & Foot Board Post Sticker Parts (box # 2) - Head Board Panel, 1 pc. ( HB Panel ) - Foot Board Panel, 1 pc. ( FB Panel ) HB Panel PLEASE REMOVE AFTER ASSEMBLY Head & Foot Board Panel Sticker Page 2 of 5
Step 1 A. Attach all dowels as shown Wooden Dowel Head Board Panel top rail B. Fix all Head Board Posts on to the Head Board Panel and all the Foot Board Posts on to the Foot Board Panel as shown.use the 120mm bolt and barrel nuts provided. Allen Key Head Board Post Barrel Nut M6 x 120mm Bolt HBR Head Board Post left Head Board Post Head Board Panel Head Board Panel top rail Head Board Panel bottom rail HB Panel PLEASE REMOVE AFTER ASSEMBLED Barrel Nut HBR Head Board Post Right Head Board Panel bottom rail HBR Head Board Post Right Allen Key Wood Dowel M6 x 120mm Bolt Wooden Dowel Head Board Post Bed Post M6 x 120mm Bolt HB Panel PLEASE REMOVE AFTER ASSEMBLY Head & Foot Board Sticker HBR Head Board Post Right Head & Foot Board Post Sticker Page 3 of 5
Bed Assembly Instructions Step 2/Diagram 1 WILSHIRE BED Fix both Side Rails to the Head Board and Foot Board as shown in diagram 1 with the 20mm bolts and washers. Step 3/Diagram 2 Further secure the pre-drilled slats to the slats support and support legs with 4nos M6 x 70mm bolt as shown in diagram 2. Step 4/Diagram 3 Page 4 of 5 Head board M8 x 20mm Bolt Allen key Head Board Leg Threaded Hole Washer Diagram 1 Place both ends of the assembled slats into the bed frame resting on side rails and screw them in place with the 32mm screws provided as shown in diagram 4. Side Rail Slat Side Rail Metal Bracket Fasten screws to all slats on side rail M4 Allen key M6x70mm Bolts Screw 4nos M6 x 70mm bolt fastened to 4nos pre-drilled slats Center Slat Support Pre-drilled Slat Leg Support Diagram 3 Foot board Leveler Diagram 2 Model shown for assembly instructions only
Bed Assembly Instructions Step 5/Diagram 4 WILSHIRE BED Diagram 4 Longer canopy rail Attach the metal pin onto hole on top of Head Board Post and Foot Board Post. Attach the shorter canopy rail on top of Head Board Post and Foot Board Post first, then attach the longer canopy rails as shown. Shorter canopy rail Metal pin Bed post Page 5 of 5
Positano / 500 Series Casegood Assembly of Knobs. Step #1 Remove Drawer Knobs as shown To replace Wood knobs with the Metal knobs, remove the Wood knobs and assemble the Metal knobs with the bolts provided along with the Metal knobs. Step #2 Assemble knobs on the outside as shown. Drawer Knobs Bolt The Fusion of Function and Comfort with Style
500S Series 6 Drawer Dresser Removing of Center Leg The center Leg is added for additional support. It is an optional extra. You may remove it if you wish, The following steps will assist you in doing this slide direction Center Leg slide direction STEP 1 First, turn the Dresser upside down as shown on a clean smooth surface to avoide any scratches Plastic Wrapper STEP 2 Remove the center support leg from the cleat as shown. 6 Drawer Dresser *For Illustration purposes only
500 SERIES/MONTEGO MIRROR FRAME Please remove the hooks that are attached on the mirror if you want to change the hanging position from potrait to landscape.to change hook position, use predrilled holes as shown below. Use Philips screw driver to remove hook and reattach accordingly. Hook *Not Included Predrill Hole Fig. 1 : Potrait Position Fig. 2 : Landscape Position
500 Series TV Armoire Step 1 Remove door knobs as shown Fixing of Door Knobs and converting the armoire into a wardrobe. Step 2 Refix knobs on the outside as shown Knob Bolt Pull string to open the door Additional part Fixing Tool 1 pc - Wooden Rod Phillips Screwdriver Page 1
Optional Step If you want to convert your TV Armoire into a Wardrobe, please follow instructions below. Step 4 : Lift the TV Armoire up right and remove the TV Shelf and place the Wooden Rod into the bracket attached to the Side panel. Wood screw Side Panel Step 3 : Tilt down the Armoire and unscrew all 8 wood screw to removed the TV Shelf Screw Driver Page 2 Bracket Wooden Rod
Optional Step If you want to convert your TV Armoire to a wardrobe, please place the wooden rod into the bracket attached to the Side Panel. Due to 'settling' and 'transportation', there is a chance that you may have to adjust the doors of the armoire. You may loosen the screws on the door hinges (as shown) and adjust the doorsand retighten the screws. Please note that this adjustment may not be required. You may also loosen the screws for the Push Open Magnets and Roller Catches if the two doors does not align and close pproperly. Wooden rod clothing hanger Wooden rod bracket Page 2 Hinge Screw Screw driver
Step 5 : Now you have a wardrobe with a cloth hanger. Page 3