27 512 MHz Base Station Antennas for Mobile Communications
Photo on title page: Applications for TETRA. Catalogue Issue /4 All data published in previous catalog issues hereby becomes invalid. We reserve the right to make alterations in accordance with the requirements of our customers, therefore for binding datas please check valid datasheets! Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 19-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. In addition, please use our information brochure about mounting configurations. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. Quality leads the way As the world s oldest and largest antenna manufacturer, we live up to claim Quality leads the way on a daily basis. One of the fundamental principies is to always be on the lookout for the best solution for our customers. Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 91 and EN ISO 141. Internet: www.kathrein.de KATHREIN-Werke KG. Telephone +49 8 1 1 84-. Fax +49 8 1 1 84-9 91 Anton-Kathrein-Straße 1. PO Box 4 44. D-84 Rosenheim. Germany
68 87.5 MHz: Trunking system, Rescue services Directional Antennas 146 174 MHz: Trunking system, Rescue services 6 512 MHz: e.g. TETRA, TETRAPOL, GSM 45, CDMA 45, Trunking system 27 87.5 MHz: Trunking system, Rescue services Omnidirectional Antennas 146 174 MHz: Trunking system, Rescue services 7 47 MHz: e.g. TETRA, TETRAPOL, GSM 45, CDMA 45, Trunking system Indoor 7 45 MHz: e.g. TETRA, TETRAPOL, GSM 45, CDMA 45, Trunking system Electrical Accessories Splitters Filter Products Mechanical Accessories Clamps, Downtilt Kits,... Technical Information
Subject to alteration Antennen Electronic Antennen Electronic Antennen Electronic List of available Catalogues for Mobile Communication Antennas and Accessories 79 25 MHz Base Station Antennas for Mobile Communications 27 512 MHz Base Station Antennas for Mobile Communications 27 512 MHz Base Station Antennas for Mobile Communiations Professional Antennas for Ground-to-Air Communications Ground-to-Air Communication Antennas Antennas for Trains and Buses Antennas for Trains and Busses 79 25 MHz Filters, Combiners, Amplifiers for Mobile Communications 45 MHz Filters, Combiners, Amplifiers for Mobile Communications 45 MHz Filters, Combiners, Amplifiers for Mobile Communications 8 MHz/16 MHz Filters, Combiners, Amplifiers for Mobile Communications 8 / 16 MHz Filters, Combiners Amplifiers for Mobile Communications The listed catalogues are also available on CD-ROM including radiation patterns in msi-format KATHREIN- Mobilfunkantennen Antennas for Mobile Communications Version 8, Edition 2/4 No.: 9987-152 Antennen Electronic 4
Summary of Types The articles are listed by type number in numerical order. Type No. Page Type No. Page Type No. Page Type No. Page 711... 77 545 54 K 51... K 62... 711 5 45 77 546 55 K 51 24 72 8 K 62 55 21 66 77 97 76 K 51 25 42 1 4... K 62 55 41 66 71... 77 975 76 K 51 26 2 45 K 62 56 21 66 71 645 8 K 51 26 41 1 9 K 62 56 41 66 78... K 51 26 42 1 9 K 62 57 21 66 716... 78 44 79 K 62 57 41 66 716 192 8 78 546 75... K 52... K 6... 72... 79... K 52 7 21 16 K 6 2 22 1 67 72 842 57 79 54 29 K 52 2 21 17 K 6 2 22 7 67 72 88 52 79 56 K 6 2 2 1 67 79 99 1 K 5... K 6 2 2 7 67 721... K 5 17 41 11 K 6 2 24 1 67 721 87 51 741... K 5 18 21 15 K 6 2 24 7 67 721 88 52 741 515 2 K 5 19 21 14 741 516 21 K 5 19 41 1 K 72... 728... 741 517 2 K 5 19 42 1 K 72 22 41 2 728 888 52 741 518 24 K 72 22 47 2 728 889 57 K 55... 742... K 55 16 21 1 47 K 7... 71... 742 77 K 55 16 22 1 47 K 7 12 21 4 71 291 28 742 4 77 K 55 16 2 1 47 K 7 2 21 71 651 76 742 5 77 K 55 26 26 46 K 7 6 21 25 742 6 77 K 55 26 27 46 K 7 51 21 5 7... 742 155 56 K 55 26 28 46 7 677 76 742 242 22 K 55 28 41 41 K 75... 7 678 76 K 55 29 21 48 K 75 11 21 5... 7 679 76 8... K 75 15 21 1 51 7 68 76 8 252 26 K 61... K 75 15 22 1 51 7 695 74 8 25 27 K 61 14 1 74 K 75 16 21 1 52 8 278 62 K 61 14 2 74 K 75 16 7 5 76... 8 6 K 61 14 74 K 75 29 21 58 76 81 6 K 61 14 4 74 85... K 61 14 5 74 77... 85 2 75... K 61 11 8 77 5... 85 75... K 61 21 8 77 299 6 85 6 78 K 61 8 77 98 8 85 7 75 K 61 4 8 5
Antenna Designs: Antenna Families Harmony of Design and Technology Omnidirectional antennas XPol Directional antennas with HPBW 9 XPol / VPol Directional antennas with HPBW 65 Omnidirectional antennas, broadband Groundplane antenna Directional antennas, logarithmic-periodic 6
Antenna Designs: Antenna Families Distinguishing features Design Radome Environmental influences Environmental conditions Large variety of half-power beam width, gain values Multi-functional installation hardware Small size and elegant design are the distinguishing features of Kathrein s antenna families. The radomes cover the internal antenna components. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance, painting and best weather protection. The design of Kathrein antennas is based on fundamental engineering knowledge and also on decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability. Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 19-1-4 class 4.1 E. The antennas exceed this standard with regards to the following items: Low temperature: 55 C High temperature (dry): +6 C According to the antenna type selected, customer can choose from different half-power beam widths and different gain values. Depending on the type, the antennas are equipped with up to 2 fixing points. Panels can be wall mounted without any additional hardware. For mast mounting, stainless steel brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories). 7
8
Summary Directional Antennas 68 87.5 MHz Directional 68 87.5 MHz Type Type No. Height Input Page [mm] Yagi 68 8 162 K 5 19 41 1 2 N female Yagi 74 87.5 162 K 5 19 42 1 2 N female Yagi 68 87.5 12 6 K 5 17 41 28 N female 11 Gain ref. λ /2 dipole 9
Directional Antennas Polarization 68... 87.5 H or V K 5 19 41 1: Yagi 68 8 162 K 5 19 42 1: Yagi 74 87.5 162 Type No. K519411 K519421 Frequency range 68 8 MHz 74 87.5 MHz Polarization Usable for horizontal or vertical polarization. Gain (ref. λ /2 dipole) Impedance 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Material: Mounting: Grounding: Special features: Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from 6 115 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. The antenna will be shipped dismounted. 162 Mechanical specifications 77 Input N female Weight 12 kg Wind load 26 N (at 15 km/h) Max. wind velocity 18 km/h in E-plane in H-plane Packing size Height Distance dipole / mast 2154 x 798 x 12 mm approx. 2 mm approx. 12 mm
Directional Antenna Polarization 68 87.5 V 4-element Yagi antenna, large bandwidth. Hot-dip galvanized steel. Gain 6. Yagi 68 87.5 12 6 Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K 5 17 41 68 87.5 MHz Vertical 6 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Material: Mounting: Grounding: Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from 6 115 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. Radiation patterns at different frequencies: 14 7 Horizontal 69 MHz Vertical 69 MHz 12 6 Horizontal 77 MHz 8 Vertical 77 MHz 58 Mechanical specifications Input N female Weight 22 kg Wind load 52 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 2424 x 2118 x 182 mm Height approx. 28 mm Yagi length approx. 2 mm Horizontal 86 MHz Vertical 86 MHz 11
12
Summary Directional Antennas 146 174 MHz Type Type No. Height Input Page [mm] Directional 146 174 MHz Yagi 146 174 17 K 5 19 21 6 N female 14 Yagi 146 174 118 4 K 5 18 21 1 N female 15 Yagi 146 174 6 8.5 K 52 7 21 22 N female 16 Panel 146 174 65 8 K 52 2 21 12 N female 17 Gain ref. λ /2 dipole 1
Directional Antenna Polarization 146 174 H or V Yagi 146 174 17 Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K 5 19 21 146 174 MHz Usable for horizontal or vertical polarization. 5 Ω VSWR < 1.4 Max. power 56 W (at 5 C ambient temperature) Material: Hot-dip galvanized steel. All screws and nuts: Stainless steel. Mounting: On masts from 6 125 mm diameter, clamps supplied. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. 17 Mechanical specifications 8 Input N female Weight 6.5 kg Wind load 145 N (at 15 km/h) Max. wind velocity 2 km/h in E-plane in H-plane Packing size Height Yagi length 1124 x 816 x 92 mm approx. 6 mm approx. 65 mm 14
Directional Antenna Polarization 146 174 H or V Yagi 146 174 118 4 Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K 5 18 21 146 174 MHz Usable for horizontal or vertical polarization. 4 5 Ω VSWR < 1. Max. power 8 W (at 5 C ambient temperature) Material: Hot-dip galvanized steel. All screws and nuts: Stainless steel. Mounting: On masts from 6 125 mm diameter, clamps supplied. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. 118 Mechanical specifications 58 Input N female Weight 7.5 kg Wind load 17 N (at 15 km/h) Max. wind velocity 2 km/h in E-plane in H-plane Packing size Height Yagi length 1112 x 92 x 94 mm approx. 1 mm approx. 75 mm 15
Directional Antenna Polarization 146 174 H or V Yagi 146 174 6 8.5 Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K 52 7 21 146 174 MHz Usable for horizontal or vertical polarization. 8.5 5 Ω VSWR < 1.5 Max. power 25 W (at 5 C ambient temperature) Material: Mounting: Grounding: Shipping: Antenna: Weather-resistant aluminum. All screws and nuts: Stainless steel. On masts from 6 5 mm diameter, by means of supplied mounting kit. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. The antenna will be shipped dismounted. Mechanical specifications 5 6 Input N female Weight kg Wind load (at 15 km/h) Horizontal: Vertical: lateral: 25 N 2 N frontal: 14 N 14 N in E-plane in H-plane Max. wind velocity 2 km/h 22 km/h Packing size 1954 x 186 x 162 mm Height approx. 22 mm Yagi length approx. 19 mm 16
Directional Antenna Polarization 146 174 H or V Yagi 146 174 65 8 Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K 52 2 21 146 174 MHz Usable for horizontal or vertical polarization. 8 5 Ω VSWR < 1.15 Max. power 1 W (at 5 C ambient temperature) Material: Mounting: Combination: Grounding: Ice protection: Hot-dip galvanized steel. All screws and nuts: Stainless steel. Via pair of clamps K 61 12 at masts from 6 115 mm dia. or via pair of clamps K 61 1 at masts from 115 2 mm dia. (not supplied). The antenna is especially suitable as a component in arrays to achieve various radiation patterns. All metal parts of the antenna including the mounting kit are DC grounded. Fiberglass enclosure of its critical points and the antenna s extremely sturdy construction keep it operational even during heavy icing. Mechanical specifications 58 65 Input Weight N female 25 kg Wind load 66 N (at 15 km/h) Max. wind velocity Packing size 22 km/h 14 x 14 x 75 mm Width/height/depth 12 x 12 x 5 mm in E-plane in H-plane 17
18
Summary Directional Antennas 6 512 MHz Type Type No. Height Input Page [mm] XPol Panel 8 5 65 12i 741 515 992 2 x 7-16 female 2 XPol Panel 8 5 65 15i 741 516 2 2 x 7-16 female 21 XPol Panel 8 4 68 14.5i 6 T 742 242 2 2 x 7-16 female 22 XPol Panel 8 5 88.5i 741 517 7 2 x 7-16 female 2 XPol Panel 8 5 88 1.5i 741 518 1997 2 x 7-16 female 24 VPol Panel 46 512 6 9i K 7 6 21 49 N female 25 VPol Panel 8 5 65 12i 8 252 992 7-16 female 26 VPol Panel 8 5 65 15I 8 25 2 7-16 female 27 VPol Panel 4 47 12 9i 71 291 992 7-16 female 28 VPol Panel 8 4 115 8.5i 79 54 974 7-16 female 29 VPol Panel 8 4 115 11.5i 79 56 194 7-16 female LogPer 44 512/824 96 68 /6.5/11.5i 79 99 5 7-16 female 1 LogPer 46 512 67.5i K 72 22 41 5 N female 2 LogPer 46 512 67.5i K 72 22 47 5 7-16 female 2 LogPer 46 512 87 9i K 7 2 21 4 N female Corner 6 49 44 11i K 7 12 21 5 N female 4 RHCPol Helix 4 47 12i K 7 51 21 718 N female 5 Directional 6 512 MHz 19
Panel Dual Polarization Half-power Beam Width 8 5 X 65 XPol Panel 8 5 65 12i Type No. 741 515 Frequency range 8 5 8 4 MHz 4 5 MHz Polarization +45, 45 +45, 45 Gain 11.5 i 12 i Half-power beam width Horizontal: 65 Copolar +45 / 45 Vertical: 6 Front-to-back ratio, copolar > 25 Isolation > Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) Material: Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. 9 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. 25 Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 415 8 5 45 8 5 +45 7-16 7-16 +45 / 45 Polarization Mechanical specifications 12 65 6 Input Connector position Weight 2 x 7-16 female Rearside 12 kg Wind load Frontal: 55 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 715 N (at 15 km/h) Max. wind velocity 2 km/h Horizontal Pattern Vertical Pattern Packing size Height/width/depth 62 x 562 x 274 mm 992 / 492 / 19 mm 2
Panel Dual Polarization Half-power Beam Width 8 5 X 65 XPol Panel 8 5 65 15i Type No. 741 516 Frequency range 8 5 8 4 MHz 4 5 MHz Polarization +45, 45 +45, 45 Gain 14.5 i 15 i Half-power beam width Horizontal: 65 Copolar +45 / 45 Vertical: 18 Front-to-back ratio, copolar > 25 Isolation > Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) 185 25 Material: Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. 8 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 8 5 45 8 5 +45 7-16 7-16 +45 / 45 Polarization Mechanical specifications 12 65 Input Connector position 2 x 7-16 female Rearside 18 Weight 19 kg Wind load Frontal: 1 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 154 N (at 15 km/h) Max. wind velocity 2 km/h Horizontal Pattern Vertical Pattern Packing size Height/width/depth 26 x 562 x 274 mm 2 / 492 / 19 mm 21
Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt 8 4 X 68 6 XPol Panel 8 5 68 14.5i 6 T Type No. 742 242 Frequency range 8 4 MHz Polarization +45, 45 Gain 14.5 i Half-power beam width Horizontal: 68 Copolar +45 / 45 Vertical: 18 Electrical tilt 6, fixed Front-to-back ratio, copolar > 25 Isolation > Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) 185 25 Material: Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. 8 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 8 5 45 8 5 +45 7-16 7-16 +45 / 45 Polarization Mechanical specifications 68 Input Connector position 2 x 7-16 female Rearside 18 Weight 19 kg Wind load Frontal: 1 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 154 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 26 x 562 x 274 mm Horizontal Pattern Vertical Pattern 6 electrical downtilt Height/width/depth 2 / 492 / 19 mm 22
Panel Dual Polarization Half-power Beam Width 8 5 X 88 XPol Panel 8 5 88.5i Type No. 741 517 Frequency range 8 5 8 4 MHz 4 5 MHz Polarization +45, 45 +45, 45 Gain 2 x i 2 x.5 i Half-power beam width Horizontal: 88 Horizontal: 86 Copolar +45 / 45 Vertical: 4 Vertical: 5 Front-to-back ratio, copolar > 2 > 2 Isolation > > Impedance 5 Ω 5 Ω VSWR < 1.5 < 1.5 Max. power per input 5 W (at 5 C ambient temperature) 4 5 MHz: +45 / 45 Polarization 86 165 5 8 5 45 8 5 +45 Horizontal Pattern Vertical Pattern 7-16 7-16 8 4 MHz: +45 / 45 Polarization Mechanical specifications 88 Input 2 x 7-16 female 165 4 Connector position Weight Bottom.5 kg Horizontal Pattern Vertical Pattern Wind load Frontal: 6 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 114 x x 24 mm Height/width/depth 7 / 17 / 19 mm 2
Panel Dual Polarization Half-power Beam Width 8 5 X 88 XPol Panel 8 5 88 1.5i Type No. 741 518 Frequency range 8 5 8 4 MHz 4 5 MHz Polarization +45, 45 +45, 45 Gain 2 x 1 i 2 x 1.5 i Half-power beam width Horizontal: 88 Horizontal: 86 Copolar +45 / 45 Vertical: 2 Vertical: 17 Front-to-back ratio, copolar > 2 > 2 Isolation > > Impedance 5 Ω 5 Ω VSWR < 1.5 < 1.5 Max. power per input 5 W (at 5 C ambient temperature) 4 5 MHz: +45 / 45 Polarization 86 165 17 8 5 45 8 5 +45 Horizontal Pattern Vertical Pattern 7-16 7-16 8 4 MHz: +45 / 45 Polarization Mechanical specifications 88 Input 2 x 7-16 female 165 2 Connector position Weight Bottom 18.5 kg Horizontal Pattern Vertical Pattern Wind load Frontal: 715 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 2 x x 24 Height/width/depth 1997 / 17 / 19 mm 24
Panel Vertical Polarization Half-power Beam Width 46 512 V 6 VPol Panel 46 512 6 9i Type No. K 7 6 21 Frequency range 46 512 MHz Polarization Vertical Gain 9 i Half-power beam width H-plane: 6 E-plane: 6 Impedance 5 Ω VSWR < 1.4 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Arrays: This antenna is especially suitable as a component in arrays to achieve various radiation patterns. Scope of supply: Antenna including two weather-proof covers for straight and elbow connector, but without mounting hardware. Material: Dipoles and reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. 4 186 Attachment: Use clamps K 61 14.. for tubular mast diameters of 4 521 mm (see the Mechanical Accessories part of this catalogue). Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Mounting Dimensions Grounding: All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. Horizontal Pattern 6 Vertical Pattern 6 Mechanical specifications Input N female Connector position Rearside Weight 6 kg Wind load Frontal: 22 N (at 15 km/h) Lateral: N (at 15 km/h) Rearside: N (at 15 km/h) Max. wind velocity 2 km/h Packing size 6 x 567 x 282 mm Height/width/depth 49 / 49 / 29 mm 25
Multi-band Panel Vertical Polarization Half-power Beam Width 8 5 V 65 VPol Panel 8 5 65 12i Type No. 8 252 Frequency range 8 5 8 4 MHz 4 5 MHz Polarization Vertical Vertical Gain 11.5 i 12 i Half-power beam width Horizontal: 68 Horizontal: 6 Vertical: 7 Vertical: 2 Front-to-back ratio, copolar > 18 > 2 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) 8 4 MHz 16 68 7 Horizontal Pattern Vertical Pattern 4 5 MHz Mechanical specifications 122 6 2 Input Connector position Weight 1 x 7-16 female Rearside 12 kg Wind load Frontal: 55 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 715 N (at 15 km/h) Max. wind velocity 2 km/h Horizontal Pattern Vertical Pattern Packing size Height/width/depth 62 x 562 x 274 mm 992 / 492 / 19 mm 26
Multi-band Panel Vertical Polarization Half-power Beam Width 8 5 V 65 VPol Panel 8 5 65 15i Type No. 8 25 Frequency range 8 5 8 4 MHz 4 5 MHz Polarization Vertical Vertical Gain 14.5 i 15 i Half-power beam width Horizontal: 68 Horizontal: 6 Vertical: 18 Vertical: 16 Front-to-back ratio, copolar > 2 > 2 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) 8 4 MHz 16 68 18 Horizontal Pattern Vertical Pattern 4 5 MHz Mechanical specifications 122 6 Input Connector position 1 x 7-16 female Rearside 16 Weight 2 kg Wind load Frontal: 1 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 154 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 26 x 562 x 274 mm Horizontal Pattern Vertical Pattern Height/width/depth 2 / 492 / 19 mm 27
Panel Vertical Polarization Half-power Beam Width 4 47 V 12 VPol Panel 4 47 12 9i Type No. 71 291 Frequency range 4 47 MHz Polarization Vertical Gain 9 i Half-power beam width H-plane: 12 E-plane: 5 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Scope of supply: Antenna including two weather-proof covers for straight and elbow connector, but without mounting hardware. Material: Dipole system: Brass and copper. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. Attachment: Use clamps K 61 14.. for tubular mast diameters of 4 521 mm (see the Mechanical Accessories part of this catalogue). 9 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. 6 Grounding: All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. Mounting Dimensions 12 5 Mechanical specifications Input 7-16 female Connector position Rearside Weight 9 kg Horizontal Pattern Vertical Pattern Wind load Frontal: 5 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 715 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 62 x 562 x 274 mm Height/width/depth 992 / 492 / 19 mm 28
Eurocell Panel Vertical Polarization Half-power Beam Width 8 4 V 115 VPol Panel 8 4 115 8.5i Type No. 79 54 Frequency range 8 4 MHz Polarization Vertical Gain 8.5 i Half-power beam width H-plane: 115 E-plane: 8 Front-to-back ratio > 18 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Material: Attachment: Ice protection: Grounding: Radiator: Copper, tin-plated. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. See the Mechanical Accessories part of this catalogue. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 115 Horizontal Pattern Vertical Pattern 8 Mechanical specifications Input 7-16 female Connector position Bottom Weight 4.5 kg Wind load Frontal: 16 N (at 15 km/h) Lateral: N (at 15 km/h) Rearside: 6 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 12 x 272 x 16 mm Height/width/depth 974 / 258 / mm 29
Eurocell Panel Vertical Polarization Half-power Beam Width 8 4 V 115 VPol Panel 8 4 115 11.5i Type No. 79 56 Frequency range 8 4 MHz Polarization Vertical Gain 11.5 i Half-power beam width H-plane: 115 E-plane: 18 Front-to-back ratio > 18 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Material: Attachment: Ice protection: Grounding: Radiator: Copper, tin-plated. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. See the Mechanical Accessories part of this catalogue. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 115 Horizontal Pattern Vertical Pattern 18 Mechanical specifications Input 7-16 female Connector position Rearside Weight 9 kg Wind load Frontal: 4 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 75 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 262 x 272 x 16 mm Height/width/depth 194 / 258 / mm
Logarithmic-periodic Vertical Polarization Half-power Beam Width 44 512/824 96 V 68 /6 VPol LogPer 44 512/824 96 68/6.5/11.5i Type No. 79 99 Frequency range 44 512 MHz 824 96 Polarization Vertical Vertical Gain.5 i 11.5 i Half-power beam width H-plane: 68 H-plane: 6 E-plane: 54 E-plane: 48 Front-to-back ratio > 2 > 25 Impedance 5 Ω VSWR < 1.4 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) Material: Mounting: Ice protection: Grounding: Radiator: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. The antenna can be mounted on tubular mast with a diameter of 48 115 mm with supplied clamps. The radiation system ist protected by the radome. Due its very sturdy construction, the antenna remains operational even under icy conditions. All metal parts of the antenna including the inner conductor are DC grounded. 44 512 MHz 54 68 Radiation Pattern in E-plane Radiation Pattern in H-plane Radiation Pattern in E-plane 824 96 MHz 48 6 Radiation Pattern in H-plane Mechanical specifications Input Connector position 7-16 female Bottom Weight 9 kg Wind load Frontal: 55 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 1172 x 72 x 225 mm Height/width/depth 116 / 5 / 17 mm 1
Logarithmic-periodic Vertical/ Horizontal Polarization Half-power Beam Width 46 512 V or H 67 LogPer 46 512 67.5i Type No. Frequency range Polarization Gain K 72 22 41 K 72 22 47 46 512 MHz Usable for horizontal or vertical polarization..5 i Half-power beam width H-plane: 67 E-plane: 5 Side-lobe Suppression > 25 at 44 512 MHz > 2 at 46 512 MHz Impedance 5 Ω VSWR < 1.4 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) For vertical polarization For horizontal polarization Arrays: Scope of supply: Material: Attachment: Ice protection: Grounding: Several antennas can be combined to increase the gain and to produce radiation patterns with very high side-lobe suppressions. Antenna with weather protective casing for straight connectors. Radiator and mounting kit: Aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. To tubular masts of 48 115 mm diameter using supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. For vertical polarization For horizontal polarization Radiation Pattern in H-Plane 67 Pariation Pattern in E-Plane 5 Mechanical specifications K 72 22 41 K 72 22 47 Input N female 7-16 female Weight 9 kg Wind load: Vertical: Frontal: 55 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Horizontal: Frontal: 55 N (at 15 km/h) Lateral: 9 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 1172 x 72 x 225 mm Height/width/depth 115 / 5 / 18 mm 2
Logarithmic-periodic Vertical Polarization Half-power Beam Width 46 512 V 87 VPol LogPer 46 512 87 9i Type No. K 7 2 21 Frequency range 46 512 MHz Polarization Vertical Gain 9 i Half-power beam width H-plane: 87 E-plane: 62 Side-lobe suppression > 28 at 44 512 MHz > 21 at 46 512 MHz Impedance 5 Ω VSWR < 1. Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Scope of supply: Material: Attachment: Ice protection: Grounding: Antenna with weather protective casing for straight connectors. Radiator: Weather-resistant aluminum. Radome: Fiberglass, colour: White. Mounting kit: Hot-dip galvanized steel. All screws and nuts: Stainless steel. To tubular masts of 6 115 mm diameter using supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 87 62 Horizontal Pattern Vertical Pattern Typical side-lobe suppression Typische Nebenkeulendämpfung 28 24 2 Mechanical specifications Input Connector position N female Rearside Weight 8. kg Wind load Frontal: 54 N (at 15 km/h) Lateral: 15 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 96 x 47 x 47 mm Height/width/depth 86 / 4 / 4 mm 4 45 5 55 f / MHz
Corner-reflector Antenna Vertical Polarization Half-power Beam Width 6 49 V 44 VPol Corner 6 49 44 11i Type No. K 7 12 21 Frequency range 6 49 MHz Polarization Vertical Gain 11 i Half-power beam width H-plane: 44 E-plane: 67 Impedance 5 Ω VSWR < 1.5 at 6 49 MHz < 1. at 4 47 MHz Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 18 W (at 5 C ambient temperature) Scope of supply: Material: Attachment: Special features: Grounding: Antenna with weather protective casing for straight connectors, mounting kit included. Radiator and reflector: Weather-resistant aluminum. Mounting U-bold: Stainless steel. All screws and nuts: Stainless steel. To tubular masts of 54 mm diameter using supplied U-bolts. The reflector screen folds together for transport. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 44 67 Mechanical specifications Input N female Weight 2.8 kg Wind load 14 N (at 15 km/h) Horizontal Pattern Vertical Pattern Max. wind velocity Packing size Height/width/depth 15 km/h 842 x 524 x 187 mm 5 / 1155 / 577 mm 4
Helix Antenna Right Handed Circular Polarization Half-power Beam Width 4 47 RHC RHCPol Helix 4 47 12i Type No. K 7 51 21 Frequency range 4 47 MHz Polarization Right handed circular Gain 12 i (ref. to the circularly polarized isotropic antenna) Half-power beam width Impedance 5 Ω VSWR < 1.2 Max. power 56 W (at 5 C ambient temperature) Scope of supply: Material: Attachment: Special features: Grounding: Antenna with weather protective casing for straight connectors, mounting kit included. Antenna: Copper band helix in protective fiberglass tube, colour: Grey. Reflector screen: Weather-resistant aluminum. Attachment construction: Hot dip galvanized steel. All screws and nuts: Stainless steel. To tubular masts of 6 125 mm diameter using supplied U-bolts. The reflector screen is made of two parts and can be removed for transport. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. Mounting Instructions Mechanical specifications Relative field strength in mid-band Input N female Weight 12 kg Wind load Frontal: 45 N (at 15 km/h) Lateral: 175 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 1684 x 88 x 277 mm Reflector diameter 718 mm Length / tube dia. 154 / 24 mm 5
6
Summary Omnidirectional Antennas 27 87.5 MHz Type Type No. Height Input Page [mm] VPol Omni 27 61 6 K 51 24 72 4 UHF female 8 VPol Omni 68 8 6 K 51 26 41 1 169 N female 9 VPol Omni 74 87.5 6 K 51 26 42 1 157 N female 9 VPol Omni 74.2 87.5/167.5 174 6 /6 /.5 K 51 25 42 1 188 2 x N female 4 VPol Omni 68 87.5 6 2 K 55 28 41 175 N female 41 Gain ref. λ /2 dipole Omnidirectional 27 87.5 MHz 7
Omnidirectional Antenna Vertical Polarization 27...61 V VPol Omni 27 61 6 Type No. Antenna Spare radials Frequency range Polarization Gain (ref. λ /2 dipole) Impedance Max. power K 51 24 72 K 51 24 7 1 27... 61 MHz Vertical 5 Ω 5 W (at 5 C ambient temperature) Material: Mounting: Tuning: Grounding: Radiator and radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 54 mm diameter (connecting cable runs outside the mast). By cutting radiator and radials to length in accordance to the mounting instructions. The metal parts of the antenna including the mounting kit are DC grounded. 78 On the tip of a tubular mast Laterally at the tip of a tubular mast 2,2 1,8 1,4 1, Vertical Pattern Standing Wave Ratio (VSWR) Examples of matching at various frequencies VSWR 2,2 1,8 1,4 1, VSWR 27 27,6 4 4,6 41 41,6 49 5 51 59 6 61 Mechanical specifications Input Weight * Wind load * Max. wind velocity Packing size Radiator length Length of radials * for max. antenna length UHF female 1.6 kg 1 N (at 15 km/h) 15 km/h 274 x 16 x mm max. 25 mm max. 25 mm 8
Omnidirectional Antennas Vertical Polarization 68...87.5 V K 51 26 41 1: VPol Omni 68 8 6 K 51 26 42 1: VPol Omni 74 87.5 6 K5126411 K5126421 K 51 26 4 12 K 51 26 4 22 Type No. Antenna Spare radials Frequency range 68 8 MHz 74 87.5 MHz Polarization Gain (ref. λ /2 dipole) Impedance Vertical 5 Ω VSWR < 1.5 Max. power 75 W (at 5 C ambient temperature) Material: Mounting: Side mounting at a mast: Grounding: Radiator: Stainless steel. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 4 mm diameter (connecting cable runs outside the mast). See catalogue part Technical Information. All metal parts of the antenna including the mounting kit are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Horizontal Pattern 78 Vertical Pattern Mechanical specifications Input K 51 26 41 1 K 51 26 42 1 N female Weight 1.8 kg 1.6 kg Wind load 7 N 65 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 1114 x 12 x 112 mm Radiator length 747 mm 68 mm Length of radials 5 mm 97 mm 9
Dual-band Omnidirectional Antenna Vertical Polarization 74.2 77.7 84. 87.5 V 167.5 174 V VPol Omni 74.2 87.5/167.5 174 6 /6 /.5 Type No. Antenna Spare radials K 51 25 42 1 K 51 25 4 2 Frequency range 74.2 77.7 MHz and 167.5 174 MHz 84. 87.5 MHz Polarization Vertical Gain (ref. λ /2 dipole).5 Decoupling Impedance < between 2 m band and 4 m band 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Material: Mounting: Special features: Grounding: Radiator: Weather-resistant aluminum in fiberglass radome. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. To pipes of 54 mm diameter by means of mounting kit (supplied). The antenna must be mounted in such a manner, that the feeder cables runs outside the mast. The radials can be fold up. All metal parts of the antenna including the mounting kit are DC grounded. Mechanical specifications 78 Input 2 x N female Weight 2.7 kg Wind load 9 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 116 x 12 x 1 mm Radiator length 1121 mm Horizontal Pattern Vertical Pattern Diameter Length of radials 5 mm mm 4
Omnidirectional Off-set Antenna Vertical Polarization 68 87.5 V VPol Omni 68 87.5 6 2 Type No. Frequency range Polarization Radiation pattern Gain (ref. λ /2 dipole) Impedance K 55 28 41 68 87.5 MHz Vertical Preferred direction: mast to radiator. 2 5 Ω VSWR < 1.5 Max. power 2 W (at 5 C ambient temperature) Material: Mounting: Grounding: Hot-dip galavanized steel. Radome: Fiberglass. All screws and nuts: Stainless steel. On masts from 6 115 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. Mechanical specifications 78 Input N female Weight 9 kg Wind load 165 N (at 15 km/h) Max. wind velocity 2 km/h Horizontal Pattern Vertical Pattern Mast diameter Packing size Dipole length Distance dipole / mast 6 115 mm 18 x 948 x 7 mm approx. 175 mm approx. 87 mm 41
42
Summary Omnidirectional Antennas 146 174 MHz Type Type No. Height Input Page [mm] VPol Omni 74.2 87.5/167.5 174 6 /6 /.5 K 51 25 42 1 188 2 x N female 44 VPol Omni 146 174 6 K 51 26 2 95 cable termination 45 VPol Omni 146 174 6 711 5 95 N female 45 VPol Omni 146 156 6 K 55 26 26 85 cable termination 46 VPol Omni 155 165 6 K 55 26 27 42 cable termination 46 VPol Omni 164 174 6 K 55 26 28 99 cable termination 46 VPol Omni 146 156 6 4 K 55 16 21 1 48 cable termination 47 VPol Omni 155 164 6 4 K 55 16 22 1 4645 cable termination 47 VPol Omni 164 174 6 4 K 55 16 2 1 4 cable termination 47 VPol Omni 146 174 6 2 K 55 29 21 84 N female 48 Gain ref. λ /2 dipole Omnidirectional 146 174 MHz 4
Dual-band Omnidirectional Antenna Vertical Polarization 74.2 77.7 84. 87.5 V 167.5 174 V VPol Omni 74.2 87.5/167.5 174 6 /6 /.5 Type No. Frequency range 74.2 77.7 MHz and 167.5 174 MHz 84. 87.5 MHz Polarization Vertical Gain (ref. λ /2 dipole).5 Decoupling Impedance Antenna Spare radials K 51 25 42 1 K 51 25 4 2 < between 2 m band and 4 m band 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Material: Mounting: Special features: Grounding: Radiator: Weather-resistant aluminum in fiberglass radome. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. To pipes of 54 mm diameter by means of mounting kit (supplied). The antenna must be mounted in such a manner, that the feeder cables runs outside the mast. The radials can be fold up. All metal parts of the antenna including the mounting kit are DC grounded. Mechanical specifications 78 Input 2 x N female Weight 2.7 kg Wind load 9 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 116 x 12 x 1 mm Radiator length 1121 mm Horizontal Pattern Vertical Pattern Diameter Length of radials 5 mm mm 44
Omnidirectional Antennas Vertical Polarization 146 174 V VPol Omni 146 174 6 Type No. Antenna Spare radials Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K51262 711 5 K 51 26 2 2 K 51 26 2 2 146 174 MHz Vertical 5 Ω VSWR < 1.5 Max. power 17 W 7 W (at 5 C ambient temperature) Material: Mounting: Side mounting at a mast: Grounding: Radiator and radials: Weather-resistant aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 4 mm diameter (connecting cable runs outside the mast). See catalogue part Mechanical Accessories. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. On the tip of a tubular mast Laterally at the tip of a tubular mast Horizontal Pattern 78 Vertical Pattern Mechanical specifications K 51 26 2 711 5 Input By means of N female a cable RG-21/U with termination inside antenna. Weight 1.2 kg Wind load 25 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 654 x 112 x 97 mm Radiator length 422 mm Length of radials 617 mm 45
Omnidirectional Antennas Vertical Polarization 146...174 V K 55 26 26: VPol Omni 146 156 6 K 55 26 27: VPol Omni 155 164 6 K 55 26 28: VPol Omni 164 174 6 Type No. K 55 26 26 K 55 26 27 K 55 26 28 Frequency range 146 156 MHz 155 165 MHz 164 174 MHz Polarization Gain (ref. λ /2 dipole) Impedance Vertical 5 Ω VSWR < 1.4 Max. power W (at 5 C ambient temperature) Material: Mounting: Side mounting at a mast: Grounding: Radiator and base: Weather-resistant aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 4 mm diameter (connecting cable runs outside the mast). See catalogue part Mechanical Accessories. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. Horizontal Pattern On the tip of a tubular mast Laterally at the tip of a tubular mast 78 Vertical Pattern Mechanical specifications Input Cable needed Weight Wind load Max. wind velocity K 55 26 26 K 55 26 27 K 55 26 28 Via terminals inside antenna. RG-21/U 1. kg 5 N (at 15 km/h) 2 km/h Packing size 1254 x 112 x 97 mm Height 85 mm 42 mm 99 mm 46
Omnidirectional Antennas Vertical Polarization 146...174 V K 55 16 21 1: VPol Omni 146 156 6 4 K 55 16 22 1: VPol Omni 155 164 6 4 K 55 16 2 1: VPol Omni 164 174 6 4 Type No. K5516211 K5516221 K551621 Frequency range 146 156 MHz 155 164 MHz 164 174 MHz Polarization Gain (ref. λ /2 dipole) Impedance Vertical 4 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, colour:grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 65 5 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 9 mm diameter (connecting cable runs outside the mast). All metal parts of the antenna including the mounting kit are DC grounded. Horizontal Pattern On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 21 Mechanical specifications Input K 55 16 21 1 K 55 16 22 1 K 55 16 2 1 N female Weight 7 kg 6.5 kg 6.5 kg Wind load 28 N 27 N 25 N (at 15 km/h) Max. wind velocity 15 km/h Packing size (L) 511 mm 4826 mm 4511 mm Packing size (w x d) 198 x 152 mm Height 48 mm 4645 mm 4 mm Diameter max. 52 mm 47
Omnidirectional Off-set Antenna Vertical Polarization 146 174 V VPol Omni 146 174 6 2 Type No. Frequency range Polarization Radiation Pattern Gain (ref. λ /2 dipole) Impedance K 55 29 21 146 174 MHz Vertical Preferred direction: Mast to radiator. 2 5 Ω VSWR < 1.4 Max. power 44 W (at 5 C ambient temperature) Material: Mounting: Grounding: Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts of 6 125 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. Radiation Pattern with different mast diameters: Horizontal Pattern 6 mm Horizontal Pattern 115 mm Mechanical specifications Input N female 78 78 Weight 4.5 kg Wind load 9 N (at 15 km/h) Max. wind velocity 2 km/h Mast diameter 6 125 mm Vertical Pattern 6 mm Vertical Pattern 115 mm Packing size Dipole length Distance dipole / mast 864 x 598 x 87 mm 84 mm 5 mm 48
Summary Omnidirectional Antennas 7 47 MHz Type Type No. Height Input Page [mm] VPol Omni 7 4 6 2i 77 552 N female 5 VPol Omni 46 47 6 2i K 75 11 21 5 N female 5 VPol Omni 46 4 6 5i K 75 15 21 1 127 N female 51 VPol Omni 44 47 6 5i K 75 15 22 1 1144 N female 51 VPol Omni 44 47 6 5i 721 87 1144 N female 51 VPol Omni 46 4 6 7i K 75 16 21 1 22 N female 52 VPol Omni 46 4 6 7 i 728 888 216 7-16 female 52 VPol Omni 44 47 6 7i 721 88 216 N female 52 VPol Omni 44 47 6 7i 72 88 216 7-16 female 52 VPol Omni 8 4 6 7.5i K 75 16 7 284 7-16 female 5 VPol Omni 8 4 6 7.5i 8.5 T 77 545 281.5 7-16 female 54 VPol Omni 4 4 6 8i 8.5 T 77 546 114 7-16 female 55 VPol Omni 45 47 6 8.5i 742 155 11 7-16 female 56 VPol Omni 46 4 6 i 728 889 44 7-16 female 57 VPol Omni 44 47 6 i 72 842 4175 7-16 female 57 VPol Omni 4 47 6 4i K 75 29 21 15 N female 58 Omnidirectional 7 47 MHz 49
Omnidirectional Antennas Vertical Polarization 7...47 V 77 : VPol Omni 7 4 6 2i K 75 11 21: VPol Omni 46 47 6 2i Type No. 77 K 75 11 21 Frequency range 7 4 MHz 46 47 MHz Polarization Gain Impedance Vertical 2 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 78 Mechanical specifications Input Connector position N female Bottom Weight 1. kg.8 kg Radome diameter Wind load Max. wind velocity 77 K 75 11 21 21 mm 2 N (at 15 km/h) 2 km/h Packing size [mm] 112 x 97 x 654 112 x 97 x 614 Height [mm] 552 5 5 Side-mounting brackets see cataloge part Mechanical Accessories
Omnidirectional Antennas Vertical Polarization 46...47 V K 75 15 21 1: VPol Omni 46 4 6 5i K 75 15 22 1: VPol Omni 44 47 6 5i 721 87: VPol Omni 44 47 6 5i Type No. K 75 15 21 1 K 75 15 22 1 721 87 Frequency range 46 4 MHz 44 47 MHz Polarization Gain Impedance Vertical 5 i 5 Ω VSWR < 1.5 Max. power 55 W 55 W 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern Mechanical specifications Input Connector position Weight N female Bottom 1.2 kg Wind load 4 N (at 15 km/h) 5 N (at 15 km/h) Max. wind velocity K 75 15 21 2 K 75 15 22 1 721 87 2 km/h Packing size [mm] 15 x 1 x 125 x 1 x Height 127 mm 1144 mm Side-mounting brackets see cataloge part Mechanical Accessories 51
Omnidirectional Antennas Vertical Polarization 46...47 V K 75 16 21 1: VPol Omni 46 4 6 7i 721 88, 72 88: VPol Omni 44 47 6 7i 728 888: VPol Omni 46 4 6 7i Type No. K 75 16 21 1 721 88 72 88 728 888 Frequency range 46 4 MHz 44 47 MHz 46 4 MHz Polarization Gain Impedance Vertical 7 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 7 W 5 W (at 5 C ambient temperature) 18 On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern Mechanical specifications N female K 75 16 21 1 721 88 7-16 female 72 88 728 888 Connector position Bottom Weight Radome diameter Wind load Max. wind velocity 1.6 kg 21 mm 6 N (at 15 km/h) 2 km/h Packing size [mm] 2 x 1 x 112 x 97 x 2124 Height 22 mm 216 mm 52 Side-mounting brackets see cataloge part Mechanical Accessories
Omnidirectional Antenna Vertical Polarization 8 4 V VPol Omni 8 4 6 7.5i Type No. Frequency range Polarization Gain Impedance K 75 16 7 8 4 MHz Vertical 7.5 i 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Copper and brass. Radome: Fiberglass, dia. 51 mm, colour: Grey. Base: Aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is capacitively coupled. maximum mast top 15 2 17 4 Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 2 N (at 15 km/h) 2 km/h 16 x 148 x 112 mm 284 mm Side-mounting brackets see cataloge part Mechanical Accessories 5
Omnidirectional Antenna Vertical Polarization Fixed Elctrical Downtilt 8 4 V 8.5 VPol Omni 8 4 6 7.5i 8.5 T Type No. Frequency range Polarization Gain Electrical tilt Impedance 77 545 8 4 MHz Vertical 7.5 i 8.5, fixed 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is capacitively coupled. maximum mast top 15 2 14 4 Vertical Pattern 8.5 electrical downtilt Mechanical specifications Input Connector position Weight Radome diameter Windload Max. wind velocity Packing size Height 7-16 female Bottom 8.5 kg 51 mm 2 N (at 15 km/h) 18 km/h 55 x 148 x 112 mm 281.5 mm 54 Side-mounting brackets see cataloge part Mechanical Accessories
Omnidirectional Antenna Vertical Polarization Fixed Electrical Downtilt 4 4 V 8.5 VPol Omni 4 4 6 8i 8.5 T Type No. Frequency range Polarization Gain Electrical tilt Impedance 77 546 4 4 MHz Vertical 8 i 8.5, fixed 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is capacitively coupled. maximum mast top 15 2 14 4 Vertical Pattern 8.5 electrical downtilt Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 22 N (at 15 km/h) 18 km/h 76 x 196 x 2 mm 114 mm Side-mounting brackets see cataloge part Mechanical Accessories 55
Omnidirectional Antenna Vertical Polarization 45 47 V VPol Omni 45 47 6 8.5i Type No. Frequency range Polarization Gain Impedance 742 155 45 47 MHz Vertical 8.5 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is coupled capacitively. maximum mast top 15 2 12 4 Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 22 N (at 15 km/h) 18 km/h 79 x 26 x 152 mm 11 mm 56 Side-mounting brackets see cataloge part Mechanical Accessories
Omnidirectional Antennas Vertical Polarization 46...47 V 728 889: VPol Omni 46 4 6 i 72 842: VPol Omni 44 47 6 i Type No. 728 889 72 842 Frequency range 46 4 MHz 44 47 MHz Polarization Gain Impedance Vertical i 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, dia. 52 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 65 5 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 9 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. 8 Vertical Pattern Mechanical specifications Input Connector position 728 889 72 842 7-16 female Bottom Weight 7. kg 6.5 kg Radome diameter 52 mm Wind load 24 N 2 N (at 15 km/h) Max. wind velocity 15 km/h Packing size 46 x 198 x 152 mm Height 44 mm 4175 mm Side-mounting brackets see cataloge part Mechanical Accessories 57
Omnidirectional Off-set Antenna Vertical Polarization 4 47 V Omnidirectional antenna with variable antenna-to-mast distance. Depending on the distance of the radiator from the mast edge and also on the mast diameter, various radiation patterns can be achieved. VPol Omni 4 47 6 4i Type No. Frequency range Polarization Gain Impedance K 75 29 21 4 47 MHz Vertical 4 i 5 Ω VSWR < 1.5 Max. power 45 W (at 5 C ambient temperature) Material: Attachment: Special features: Grounding: Horizontal radiation pattern: Radiator: Hot-dip galvanized steel. Horizontal support pipe: Stainless steel. Mount: Aluminum. Tightening band and all screws and nuts: Stainless steel. Feedpoint radome: Fiberglass. To tubular masts of 6 2 mm diameter using supplied stainless steel tightening band (2 mm wide,.8 mm gauge). The distance from tubular mast to radiator is adjustable from 17 58 mm. All metal parts of the antenna including the inner conductor and the supplied mount are DC grounded. Depending on the distance A (edge of pipe mast to dipole) see sketch. Distance A Abstand A For worked sample please refer to page 86 Mechanical specifications Input Weight Wind load Max. wind velocity Packing size Length N female 1.6 kg 4 N (at 15 km/h) 2 km/h 88 x x mm 15 mm 58 Side-mounting brackets see cataloge part Mechanical Accessories
Summary Indoor Antennas Vertical Polarization Indoor Omnidirectional Antennas Single-band Type Type No. Height Input Page [mm] VPol Indoor 46 4 6 2i 77 299 4 cable termination 6 VPol Indoor 45 47 6 2i 76 81 6 cable termination 6 VPol Omni 7 4 6 2i 77 552 N female 61 VPol Omni 46 47 6 2i K 75 11 21 5 N female 61 Indoor Directional Antennas Single-band Type Type No. Height Input Page [mm] VPol Indoor 8 45 9 7i 8 278 292 N female 62 VPol Indoor 45 4 9 7i 8 292 N female 6 Kathrein Train Antennas a Solution also for Indoor Applications please refer to part Technical Information, page 82 Indoor 7 47 MHz 59
Indoor Omnidirectional Antennas Vertical Polarization 46... 47 V 77 299: VPol Indoor 46 4 6 2i 76 81: VPol Indoor 45 47 6 2i Type No. 77 299 76 81 Frequency range 46 4 MHz 45 47 MHz Polarization Gain Impedance Vertical 2 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Material: Mounting: Grounding: Dipole: Brass. Radome: Fiberglass, colour: White. Additional mounting plate: Aluminum. a) Single-hole mounting (12 mm diameter) on surface of up to mm thickness. b) On surfaces of more than mm thickness, by means of mounting plate included in the scope of delivery. All metal parts of the antenna including the inner conductor are DC grounded. a) b) min. Ø 22 max. mm Ceiling Ceiling Ø 5,5 Mounting plate 9 Mechanical specifications Input Cable RG 58/CU of 1 m length, grey, connector is not supplied Weight.25 kg.2 kg Radome diameter Mounting plate 77 299 76 81 2 mm 115 x 25 mm Packing size Foil: 65 x mm Height 4 mm 6 mm 6
Omnidirectional Antennas Vertical Polarization 7...47 V 77 : VPol Omni 7 4 6 2i K 75 11 21: VPol Omni 46 47 6 2i Type No. 77 K 75 11 21 Frequency range 7 4 MHz 46 47 MHz Polarization Gain Impedance Vertical 2 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) Material: Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 78 Mechanical specifications Input N female Connector position??? Bottom??? Weight 1. kg.8 kg Radome diameter Wind load Max. wind velocity 77 K 75 11 21 21 mm 2 N (at 15 km/h) 2 km/h Packing size [mm] 112 x 97 x 654 112 x 97 x 614 Height [mm] 552 5 61
Indoor Directional Antenna Vertical Polarization Half-power Beam Width 8 45 V 9 VPol Indoor 8 45 9 7i Type No. 8 278 Frequency range 8 45 MHz Polarization Vertical Gain 7 i Half-power beam width Horizontal: 9 Impedance 5 Ω VSWR < 2. Max. power 5 W (at 5 C ambient temperature) Input N female connector Protection class IP Weight 5 g Packing size approx. 2 x 25 x 6 mm Height/width/depth approx. 29 x 24 x 45 mm Material: Mounting: Reflector: Aluminum. Radome: PS, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Two holes of 6 mm diameter in the mounting plate. Screws are not supplied 9 Grounding: All metal parts inclusive the inner conductor are DC grounded. Horizontal Pattern 62
Indoor Directional Antenna Vertical Polarization Half-power Beam Width 45 4 V 9 VPol Indoor 45 4 9 7i Type No. 8 Frequency range 45 4 MHz Polarization Vertical Gain 7 i Half-power beam width Horizontal: 9 Impedance 5 Ω VSWR < 2. Max. power 5 W (at 5 C ambient temperature) Input N female connector Protection class IP Weight 5 g Packing size approx. 2 x 25 x 6 mm Height/width/depth approx. 29 x 24 x 45 mm Material: Mounting: Reflector: Aluminum. Radome: PS, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Two holes of 6 mm diameter in the mounting plate. Screws are not supplied 9 Grounding: All metal parts inclusive the inner conductor are DC grounded. Horizontal Pattern 6
64
Summary Electrical Accessories 75 MHz Type Type No. Frequency Range Height Input Max. Power Page 2-way Splitter 75 MHz K 62 55 41 68 88 MHz 95 mm N female 96 Watt 66 -way Splitter 75 MHz K 62 56 41 68 88 MHz 55 mm N female 96 Watt 66 4-way Splitter 75 MHz K 62 57 41 68 88 MHz 1195 mm N female 96 Watt 66 15 MHz Type Type No. Frequency Range Height Input Max. Power Page 2-way Splitter 15 MHz K 62 55 21 146 174 MHz 5 mm N female 68 Watt 66 -way Splitter 15 MHz K 62 56 21 146 174 MHz 6 mm N female 68 Watt 66 4-way Splitter 15 MHz K 62 57 21 146 174 MHz 7 mm N female 68 Watt 66 45 MHz Type Type No. Frequency Range Height Input Max. Power Page 2-way Splitter 45 MHz K 6 2 22 1 8 512 MHz 49 mm N female 5 Watt 67 2-way Splitter 45 MHz K 6 2 22 7 8 512 MHz 49 mm 7-16 female Watt 67 -way Splitter 45 MHz K 6 2 2 1 8 512 MHz 49 mm N female 5 Watt 67 -way Splitter 45 MHz K 6 2 2 7 8 512 MHz 49 mm 7-16 female Watt 67 4-way Splitter 45 MHz K 6 2 24 1 8 512 MHz 49 mm N female 5 Watt 67 4-way Splitter 45 MHz K 6 2 24 7 8 512 MHz 49 mm 7-16 female Watt 67 Filter products summary Combiners, Filters, Duplexers 68 + 69 For detailed information see the catalogues Filters, Combiners, Amplifiers for Mobile Communications Electrical Accessories 65
Power Splitters For outdoor and indoor use. 2-way Splitter 75 -way Splitter 75 4-way Splitter 75 16 16 mm Type No. K 62 55 41 K 62 56 41 K 62 57 41 Connector (female) Max. power N 96 W (at 5 C ambient temperature) For connecting... antennas 2 4 Frequency range 68 88 MHz VSWR < 1.1 Impedance 5 Ω Insertion loss <.5 Length L 95 mm 55 mm 1195 mm 2 mm L For outdoor and indoor use. 2-way Splitter 15 -way Splitter 15 4-way Splitter 15 Type No. K 62 55 21 K 62 56 21 K 62 57 21 Connector (female) Max. power N 68 W (at 5 C ambient temperature) For connecting... antennas 2 4 Frequency range 146 174 MHz VSWR < 1.1 Impedance 5 Ω Insertion loss <.5 Lenth L 5 mm 6 mm 7 mm Example for 2-way antenna splitter Material: Protective case on the antenna side: Aluminum. Weather protectition on the equipment side: UV-resistant Elastomere. Transformation line: Aluminum and brass. All parts with protectition varnish. Antenna Equipment Antenna Mounting: On tubular masts of 6 2 mm dia. OD by means of non-corrosive clamp-strap (2 x 2 x 1 mm, supplied). Transformers with a total length of over 7 mm are delivered with a supporting clamp. Example for 4-way antenna splitter Ant.1 Ant.2 Ant. Ant.4 K K K K K: 5 Ω-cables of the same electrical length Equipment 66
Power Splitters For outdoor and indoor use. 2-way Splitter 9/42/45 -way Splitter 9/42/45 4-way Splitter 9/42/45 Type No. K 6 2 22 1 K 6 2 22 7 K 6 2 2 1 K 6 2 2 7 K 6 2 24 1 K 6 2 24 7 Connectors (female) N 7-16 N 7-16 N 7-16 Max. power 5 W W 5 W W 5 W W (at 5 C ambient temperature) For connecting... antennas 2 4 Frequency range 8 512 MHz VSWR < 1.1 Impedance 5 Ω Insertion loss <.5 Packing size 425 x 9 x 7 mm Max. size 49 x 82 x 82 mm Material: Mounting: Case: Aluminum. Inner conductor: Brass. Bracket for wall mounting included in the scope of supply. For mounting to tubular masts use clamps as listed below (order separately). K 6 2 24 7 Clamps Type No. Description Mast Diameter 74 6 2 clamps 55 mm 74 61 2 clamps 55 75 mm 74 62 2 clamps 75 95 mm 74 6 2 clamps 95 115 mm 74 64 2 clamps 115 15 mm 74 64 67
Filters, Duplexers, Combiners Band-pass Filter K 64 21 45 1 68 87.5 MHz K 64 21 25 1 146 174 MHz K 65 21 25 1 8 47 MHz 79 965 146 174 MHz 79 964 146 174 MHz 79 967 8 47 MHz 79 966 8 47 MHz S-P Filter K 65 21 25 1 79 967 K 64 21 46 1 K 64 21 47 1 K 64 21 26 1 K 65 21 26 1 68 87.5 MHz 68 87.5 MHz 146 174 MHz 8 47 MHz Duplexer 718 987 68 87.5 MHz 719 69 68 87.5 MHz 719 628 146 174 MHz 718 88 146 174 MHz 718 785 4 47 MHz 718 29 4 47 MHz K 64 41 4 68 87.5 MHz K 64 41 44 68 87.5 MHz K 64 41 2 146 174 MHz K 64 41 24 146 174 MHz K 65 41 25 89 47 MHz K 65 41 26 8 47 MHz 782 197 8 85 / 9 95 MHz 782 198 85 9 / 95 4 MHz 79 752 4 415 / 42 425 MHz 791 55 4 415 / 42 425 MHz 791 4 415 42 / 425 4 MHz 791 67 415 42 / 425 4 MHz 792 25 45 455/ 46 465 MHz K 64 21 26 1 718 628 K 64 41 2 79 752 782 197 Hybrid Transmitter Combiner 792 67 4 x W 146 174 MHz 791 652 4 x W 4 47 MHz 792 67 Filter Transmitter Combiner 79 44 4 x 5 W 42 4 MHz Multiband Combiner K 64 5 4 68 87.5 / 146 174 MHz 721 18 68 174 / 8 47 MHz 79 244 68 174 / 4 47 MHz 782 954 68 47 / 87 97 MHz 722 47 68 47 / 87 97 MHz 79 44 728 954 68
Filters, Duplexers, Combiners - Coupler K 62 7 41 68 8 MHz K 62 7 21 14 18 MHz K 6 7 21 4 512 MHz Hybrid Ring Junction K 62 7 41 K 62 7 41 K 62 7 21 K 6 7 21 1 68 87.5 MHz 146 174 MHz 4 47 MHz Decoupled Power Splitter 742 46 1: 68 87.5 MHz 725 87 1:4 68 87.5 MHz 724 47 1: 146 174 MHz 725 24 1:4 146 174 MHz 724 48 1: 4 47 MHz 725 871 1:4 4 47 MHz K 6 7 21 1 725 871 Circulator 79 276 68 88 MHz 79 277 146 174 MHz 78 6 146 174 MHz 791 6 4 47 MHz 79 215 4 47 MHz 78 6 DC-stop 721 62 68 47 MHz 5-Ohm Loads 721 62 K 62 26 11 1 2 W 25 MHz K 62 26 41 1 W 25 MHz K 62 26 21 1 25 W 25 MHz K 62 26 1 5 W 25 MHz Receiver Multicoupler K 62 26 1 78 24 8 outputs 68 87.5 MHz 78 22 8 outputs 146 174 MHz 727 621 8 outputs 4 47 MHz 727 621 69
7
Summary Mechanical Accessories Clamps, Downtilt Kits... Directional Antennas Dimensions 72 Clamps and Downtilt kits 74 Tools Azimuth Adjustment Tool 79 Brackets Page Bracket with Fixed Spacing 8 Bracket with Adjustable Spacing 8 Mechanical Accessories 71
Directional Antennas Dimensions VPol Panel 6 / 65 / 18 XPol Panel 65 A 49 mm 992 mm 198 mm B 49 mm 492 mm 485 mm C 29 mm 19 mm 19 mm D 4 mm 9 mm 185 mm XPol Panel 88 A 7 mm 1997 mm B 24 mm 5 mm C 28 mm 9 mm B 9 72 64 182 A D Ø 11±,5 C A B C Top view 19 17 72
Directional Antennas Eurocell Panels Antenna Dimensions VPol Panel 115 Eurocell Panel A 974 mm 194 mm 2574 mm B mm 199 mm 26 mm C 7 mm 2 mm 267 mm 72 64 9 A B C Top view 258 7
Mounting Hardware for Directional Antennas VPol Panel 6 / 65 12 XPol Panel 65 Mounting clamps/downtilt kit (order separately) Type No. Suitable for Weight (Pair of pipe masts of kg clamps)... mm diameter K 61 14 1 4 95 2.6 K 61 14 2 6 116 2.6 K 61 14 116 2 4. K 61 14 4 2 8 7.2 K 61 14 5 8 521.2 7 695 Downtilt (to be used with a suitable pair of clamps for the individual mast diameter!) Antenna Height Downtilt Angle 992 mm 22 198 mm 11 Pair of clamps K 61 14 Weather-proof cover for elbow and straight connectors are supplied. Downtilt kit 7 695 straight elbow 74
Mounting Hardware for Directional Antennas XPol Panel 88 Special downtilt kit for Eurocell Panel antennas with a weight greater than 25 kg and for XPol Panel for Tetra Downtilt kit M supplied Type No. Preferred range of use 85 7 Panel antennas with a weight of 25 kg Panel antennas with attached mounting plates Downtilt kit without scale for universal use M8 supplied Weight 5.9 kg Material Hot-dip galvanized steel All screws and nuts Stainless steel Recommended mast clamps: Type No. Description Mast diameter Weight approx. Units per antenna 78 546 1 clamp 5 115 mm 1. kg 2 85 2 1 clamp 1 22 mm 2.7 kg 2 85 1 clamp 2 8 mm 4.8 kg 2 Recommended torque for all bolted connections: Screw size M8 M Torque 12 Nm 26 Nm Maximum acceptable load: Frontal wind load < 25 N Lateral wind load Antenna weight < 8 N 5 kg 64±.5 9 9 72 Downtilt angle Antenna height Downtilt angle mm 15 258 mm 11 72 9 64±.5 22 M 75
2 15 Mounting Hardware for Directional Antennas VPol Panel 115 Downtilt kits Antenna Height: 974 mm 194 mm 258 Description Mast diameter Type No. Distance A Weight Units per mm approx. antenna Small Pipe 28 64 mm *71 651 22 g see sketch Large Pipe 5 115 mm 78 546 18 26 1. kg see sketch new 1 22 mm 85 2 47 56 2.7 kg see sketch new 2 8 mm 85 48 69 4.8 kg see sketch 974 194 Off-set 6 115 mm 7 677 117 124 2. kg see sketch 115 2 mm 7 678 146 16 2.6 kg see sketch 2 8 mm 7 679 148 168 4. kg see sketch 8 521 mm 7 68 15 175 5. kg see sketch 71 651 78 546 7 677... 7 68 A Screws, washers and nuts supplied 6 912 Use the downtilt kit together with the clamps mentioned above Scale Downtilt angle Antenna Height Downtilt angle Type No. Weight 974 mm 21 77 97 approx. 2.8 kg 194 mm 11 77 975 approx. 2.8 kg Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm. 76
Eurocell Panels Sector Panel Arrangement Mounting Hardware Sector Clamp Kit / Pipe Mast with Flange Base Slim and unobstrusive design Nearly cylindrical optical appearance with small outer diameter Sector Clamp Kit Type No. 742 742 4 Angle between antennas 12 12 Suitable for mast diameter 114. mm 19.7 mm Type No. of pipe mast 742 5 742 6 (please order separately) Number of pieces 2 x sector clamp 2 x sector clamp 2 x mounting support 2 x mounting support clamp clamp Material sector clamp Hot-dip galvanized steel Hot-dip galvanized steel Mounting support Aluminum Aluminum clamp Screws Stainless steel Stainless steel Outer diameter (D out ) of the A-Panel Arrangement 42 mm 441 mm Weight Clamp kit. kg.2 kg sector clamp 1.4 kg 1.5 kg Only for Eurocell Panels 64 ±.5 9 6 sector clamp D out A C B F E D Torque 8 Nm Mounting support clamp Bottom view without downtilt kit Type No. A B C D E F 742 114. 88 217 27 49 45 742 4 19.7 26 228 49 45 all dimensions in mm D Pipe Mast with Flange Base Type No. 742 5 742 6 Pipe diameter D 114. mm 19.7 mm according DIN 2448 Wall thickness pipe 6. mm 4 mm Pipe length mm mm Flange diameter 2 mm 265 mm Flange thickness S 14 ± 1 mm 19 ± 1 mm Hole circle diameter 17 mm 225 mm Number of holes 6 6 Hole diameter 18 ± 1 mm 18 ± 1 mm Enclosed bolts thread x length M16 x mm M16 x mm Hot-dip galvanized steel Quality min. 8.8 Quality min. 8.8 Weight 6 kg 55 kg Material pipe mast S55 J2H (St 52-N) DIN EN 2-1 Material flange base S25 JR G2 (RSt 7-2) DIN EN 25 Maximum permissible load: According DIN 411 and DIN 412 Fatigue class K2 S 17 2 742 5 18±1 129 ± 2 225 265 742 6 77
Eurocell Panels Mounting Hardware 2 x C-Panel Mounting Kit Only for Eurocell Panels Use this mounting kit only for antennas less than 25 kg each. Type No. 85 6 No. of pieces 2 x brackets Suitable for A-/C-Panels 65, 9 with a max. height 2.6 m Material: Clamp Hot-dip galvanized steel Screws Stainless steel Weight Approx.. kg Mounting Screws are supplied Recommended torque for M8 bolted connections: 12 Nm 4 9±1 64±.2 64±.2 64±.2 R 7 9±.5 28±.5 Mounting Accessories (order separately) Clamps (only the listed clamps are allowed!) Type No. Description Remarks Weight Units per approx. antenna 85 2 1 clamp Mast: 1 22 mm diameter 2.7 kg 2 85 1 clamp Mast: 2 8 mm diameter 4.8 kg 2 Please chose the fitting downtilt kit that you need, from the antenna datasheet. 78
A-Panel / C-Panel / F-Panel / Eurocell Panel Accessories Azimuth Adjustment Tool Type No. 78 44 Precise azimuth adjustment for mast mounted antennas can easily be achieved by using the azimuth adjustment tool. This tool is suitable to all types of Eurocell Panels Panels A-Panels C-Panels F-Panels X-Pol F-Panels Target object Scale Target object Elevation compensation Move the stopper to central position* Panel Clamping device A-Panel F-Panel equivalent for 262 A-Panel F-Panel 199 F-Panel F-Panel 155 equivalent for F-Panel X-Pol-F-Panel F-Panel X-Pol-F-Panel Instruction: Use a map to work out the angle between the designed antenna azimuth and target (church, building, mountain peak). Set this angle on the scale of the adjustment tool. Place the adjustment tool onto the antenna and tighten the clamping device. Use the telescope to aim at the target object, if necessary, use elevation compensation. Then rotate the antenna until the target object appears in the telescope. * Observe the position of the stopper when fitting the azimuth adjustment tool. 79
Accessories Stand-off Brackets When mounted to the tip of a mast, the antennas described in this catalogue radiate horizontally in a circular fashion. However, they can also be mounted laterally to a mast by using an extension bracket. Depending on the spacing and the mast diameter, various types of radiation patterns can be achieved. (For further information please see the Technical Information part of our catalogue on pages 86 and 87) Bracket with fixed spacing Type No. K 61 716 192 K 61 4 71 645 Weight Distance A: Suitable for antennas with a maximum wind load of Suitable for antennas with Attachment Material Wind load 2 kg 7 kg.2 kg 8.5 kg 5 mm mm 215 N (at 15 km/h) 85 N (at 15 km/h) mounting kit to pipe masts of 2 54 mm diameter. By means of mounting kit (supplied) to pipes of 55 mm 5 mm 55 mm 5 mm 5 mm 265 mm 5 mm 265 mm diameter Hot-dip galvanized steel. 6 N (at 15 km/h) 6 N (at 15 km/h) 515 mm K 61 K 61 4 pipe diameter 44.5 x 2.6 mm 15 mm pipe diameter 44.5 x 2.6 mm 95 Bracket with adjustable spacing A Implementation Stand-off Double stand-off fig. A fig. B fig. C A: 125 68 mm D: 45 mm A D Type No. K 61 11 K 61 21 77 98 Weight 6.6 kg 1.7 kg 6 kg Distance A: min. 125 mm mm max. 68 mm 24 mm Suitable for antennas with mounting kit to pipe masts of 2 54 mm 9 mm 5 94 mm diameter diameter Attachment By means of mounting kit (supplied) to pipes of 55 mm 5 mm 4 5 mm diameter diameter Material Hot-dip galvanized steel. Wind load 45 N N 65 N (at 15 km/h) (at 15 km/h) (at 15 km/h) 74 mm 245 mm Double Bracket 125 to 68 mm 74 mm Pipe 48. x 2.6 mm ( mm length) free length 65 mm 4 x 4 mm 125 to 68 mm 2 1 4 x 4 mm Pipe 76.1 x 2.6 mm free length 18 mm to 24 mm L x 4 Pipe 7 x 4 mm free length 25 mm 4 x 4 mm L x 4 fig. A fig. B fig. C 2 1 8
Summary of Technical Information Type Page Kathrein Train Antennas a Solution also for Indoor Applications 82 Antenna Systems with Panels K 52 2 2.. 8 Examples of Radiation Patterns at 9 MHz with Combinations of Panels 741 517 84 Examples of Radiation Patterns at 9 MHz with Combinations of Panels 8 252 85 Radiation Patterns for Side-mounted Omnidirectional Antennas 86 Isolation Between Two Half-wave Dipoles 87 Isolation of Two Vertically Stacked Panels K 7 2. 88 Antenna Gain, VSWR / Reflected power 89 VSWR-reduction / Mismatch loss 9 81 Technical Information
Kathrein Train Antennas a Solution also for Indoor Applications Kathrein train antennas has been implemented on indoor systems all over the world. Advantages: Sophisticated and robust design based on a fiberglass radome. Because of this rugged radome design, the antenna is well protected against vandalism. Low profile broadband antenna with small optical appearance. Especially in lower frequency applications, indoor antennas may have an unhandy size. This is due to the fact, that the antennas normally use a halfwave lambda radiator. Example: TETRA 9 MHz, antenna length roughly 4 mm. 14 mm Train antennas are based on quarterwave radiators resulting in conjunction with a special radiator design in very low lengths. The antenna 72 997 for the range of 8 412 MHz (see picture aside) is only 14 mm long! For a proper operation these antennas need an electrical counterweight or ground plane of a certain min. dimension. Mounting situation: The antennas has to be mounted on a conductive surface with dimensions according to the datasheet. This could be realized by a metallic sheet on the ceiling or directly by mounting the antenna on a metallic artificial ceiling. For a good contact one side of the antenna flange is not painted. Accordingly also the ground plane should be free of color in the area of mounting location. We strongly recommend to follow these specifications, otherwise the VSWR of the antenna will increase, destroying the performance of the antenna. Painting: The radome and base can be painted in any long-lasting color to match the surroundings. Suitable commercial paints consist of one or two components. The manufacturer s instruction for use and processing must be observed. Paints with metallic effects or metallic components are not permissible. Indoor system at the airport of Singapore with Kathrein train antennas 82