Technical Application Guide for UP-SHINE LED Downlight UP-DL11-4&6-15W-D
Introduction DL11 is a led down light with graceful and compact design. It adopts ADC12 aluminum housing with excellent heat dissipation and 5VA fire-rated PC cover with excellent working performance. This lamp adopts high efficiency SMD2835 LED chip to provide soft and uniform lighting. Easy to install with or without spring clips, acting as 4/6inch recessed retrofit or surface mounted ceiling light. Features 1. Can fit for 4 / 6 inch housing. 2. Recessed and surface mounted installation way available. 3. Aluminum fixture with excellent heat dissipation. 4. Fire-rated PC lens. Uniform lighting distribution. 5. Traic dimming, comply with most of dimmers in the market. Application notes Damp location The lamp must be installed by professional electrician Ensure the power supply is switched off before fitting this product Do not touch the lamp when in use Keep away from hot steam and corrosive gas Application Areas It is designed for general lighting applications in office, supermarket, shop, school, hotel, etc. It is also widely used for public areas, such as stairway, lobby, reception, corridors etc. Certificate www.upshine.com info@upshine.com
Product Information Ø185(7.28'') Technical Specifications 32.8(1.3'') 57(2.24'') Model Voltage Power Power Factor Lumen (±5%) Beam angle CCT Lifespan CRI Dimmable Dimension UP-DL11-4&6-15W-D AC12V 15W.85 11 11 3K 5h 8 Yes UP-DL11-4&6-15W-D AC12V 15W.85 115 11 35K 5h 8 Yes UP-DL11-4&6-15W-D AC12V 15W.85 115 11 4K 5h 8 Yes UP-DL11-4&6-15W-D AC12V 15W.85 12 11 5K 5h 8 Yes Driver data Sheet Ø185*57mm (7.28"*2.24") Ø185*57mm (7.28"*2.24") Ø185*57mm (7.28"*2.24") Ø185*57mm (7.28"*2.24") Driver data Dim Input rated Voltage Frequency Input Voltage AC12V 6Hz AC1-14V Efficiency 7% Total load Wattage 15W±1W Power Factor.85 Rated input current Full load output Voltage Rated output current Output current range.15a DC12-14V 9mA 9mA±5% Power tolerance ±5% Current output tolerance ±5% Dimming range 8%-1% Dimmer Short circuit protection Over voltage protection Over temperature protection THD Withstand voltage Triac dimmers PASS PASS PASS Fixture Compatibility Rated Wattage Electrical Classification Ingress Protection Operating Temp Operating Humidity Storage Temp 15W Ground connection Damp location -2 o C~45 o C ~9% -2 o C~65 o C www.upshine.com info@upshine.com
UNIT: cd Spectral Distribution 3K 35K.8 Max=8754 [1.=2] 4.75 SDCM F3K.8 Max=858 [1.=2] 2.38 SDCM F35K.7.7.6.6 Spectrum.5.4.3 x=.445 y=.3943 Spectrum.5.4.3 x=.4127 y=.3937.2.2.1.1. 38 5 6 7 8 Wavelength(nm). 38 5 6 7 8 Wavelength(nm) 4K 5K.8 Max=857 [1.=2] 2.83 SDCM F4K.8 Max=1348 [1.=2] 1.3 SDCM F5K.7.7.6.6 Spectrum.5.4.3 x=.3855 y=.3822 Spectrum.5.4.3 x=.3476 y=.3587.2.2.1.1. 38 5 6 7 8 Wavelength(nm). 38 5 6 7 8 Wavelength(nm) Photometric Diagram 3K 35K Polar intensity diagram Cartesian intensity diagram Beam diagram Polar intensity diagram Cartesian intensity diagram Beam diagram -12-9 -/+18 8 16 24 12 9 E(LX) 4. 3.6 3.2 2.8 2.4 2. 1.6 Planar Illuminance Curve MH=1m C/18 C9/27 Flux out: 828.6 lm -12-9 -/+18 8 16 24 12 9 E(LX) 4. 3.6 3.2 2.8 2.4 2. 1.6 Planar Illuminance Curve MH=1m C/18 C9/27 Flux out: 817.8 lm 32 4-3 3 UNIT: cd AVERAGE BEAM ANGLE(5%): 113.2 DEG 1.2.8.4-25 -2-15 -1-5 5 1 15 2 25 Distance(m) Height Eavg, Emax Angle: 112.69deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. 32 4-3 AVERAGE BEAM ANGLE(5%): 114.4 DEG 3 1.2.8.4-25 -2-15 -1-5 5 1 15 2 25 Distance(m) Height Eavg, Emax Angle: 113.82deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. 4K 5K Polar intensity diagram Cartesian intensity diagram Beam diagram Polar intensity diagram Cartesian intensity diagram Beam diagram Flux out: 88.8 lm Flux out: 898.7 lm -12 -/+18 12 E(LX) 4.5 4.5 Planar Illuminance Curve MH=1m C/18 C9/27-12 -/+18 12 E(LX) 4.5 4.5 Planar Illuminance Curve MH=1m C/18 C9/27-9 9 3.6-9 9 3.6 9 3.15 9 3.15 18 2.7 2.25 18 2.7 2.25 27 1.8 27 1.8 36 1.35.9 36 1.35.9-3 45 3.45-3 45 3.45 UNIT: cd AVERAGE BEAM ANGLE(5%): 115.1 DEG -25-2 -15-1 -5 5 1 15 2 25 Distance(m) Height Eavg, Emax Angle: 114.71deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. UNIT: cd AVERAGE BEAM ANGLE(5%): 114.4 DEG -25-2 -15-1 -5 5 1 15 2 25 Distance(m) Height Eavg, Emax Angle: 114.14deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. www.upshinelightingusa.com info@upshinelightingusa.com
Polar Diagram Comparison -15 O +/-18 O 15 O -12 O 12 O -9 O 9 O 9 18-6 O 27 6 O 36-3 O 45 3 O O AVERAGE BEAM ANGLE (5%): 114.4DEG UNIT: cd C/18, 114.5 deg C3/21, 114.4 deg C6/24, 114.4 deg C9/27, 114.4 deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11%.4 Lifetime (hours) 8 7 6 5 4 3 2 1 65 o C 75 o C 85 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 85%.35.3.25.2.15 8% 75% FLUX.1.5 U'V' 7%. 1 2 3 4 5 6 7 8 9 1 LifeTime (hours) Temperature The testing is operated at 25 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C The highest withstand temperature of IC, MOS could be 12 C The highest withstand temperature of LED junction temperature is 15 C Temperature ( o C) 1 9 8 7 6 5 4 3 2 1 11:13:13 11:25:1 11:37:1 11:49:1 12:1:1 12:13:1 12:25:1 12:37:1 12:49:1 13:1:1 13:13:1 13:25:1 13:37:1 13:49:1 14:1:1 14:13:1 14:25:1 14:37:1 14:49:1 15:1:1 15:13:1 15:25:1 15:37:1 15:49:1 16:1:1 16:13:1 16:25:1 16:37:1 Time IC Capacitor MOS PCB LED Fitting Environmental temperature The driver lifespan is based on capacitor working temperature. www.upshinelightingusa.com info@upshinelightingusa.com
Replace 4" traditional down light, Installation method 1.Open the package, take out the lamp and clips, insert the three clips to the corresponding holes of the lamp and ensure it is firmly fixed to the lamp. 2.Screw the E26 base to the 4" down light housing, connect the male & female connector. Connect the ground wire with wiring nut. 3. Push the lamp into the housing until the clips firmly stuck in the housing. 4. Installation complete. Replace 6" traditional down light Picture (a) Picture (b) Picture (b1) Picture (b2) Picture (b3) www.upshinelightingusa.com info@upshinelightingusa.com
Picture (c) Picture (d) Picture (e) 1. Open the package,take out the spring and bracket ( picture a ), screw the spring into the brackets according to the b1 b 2 b3 step.( picture b ) 2. fix the bracket on the back of the lamp,( picture c) 2. Screw the E 26 base into the 6" down light housing, connect the female and male connectors ( picture d).connect the ground wire with wiring nut. 3. Push the lamp into the housing until the clips firmly stuck in the housing (picture d,e). 4. installation complete ( picture e) J-BOX: Installation with J-BOX: Surface Mounted Picture (a) Picture (b) Picture (c) Picture (d) 1. Open the package,take out the bracket ( picture a ).Connect the ground wire with wiring nut. 2. Lock the brackets on the J-BOX by screws.( picture b ) 3. Connect AC cables (L: white to white, N: black to black) (picture c) 4. Push the lamp to the bracket until snap joint of bracket firmly stuck to the lamp (picture c,d) 5. Installation complete ( picture d) www.upshinelightingusa.com info@upshinelightingusa.com
Packaging Information Carton SIZE(CM) 44.5*44.5*44.5 17.5"*17.5"*17.5" N.W/pc (KGS) G.W.(KGS) Q'TY(PCS).3 1 2 2'' standard container 4'' standard container CTNS Q'TY(PCS) VOLUME(CBM) 31 62 28 62 124 56 www.upshinelightingusa.com info@upshinelightingusa.com Phone: +86 755 2919 7389 Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China