Features General Description Precision reference voltage AP432 : 1.24V ± 1% AP432A : 1.24V ± 0.5% Sink current capability: 200mA Minimum cathode current for regulation: 150μA Equivalent full-range temp coefficient: 30 ppm/ o C Fast turn-on response Low dynamic output impedance: 0.2Ω Programmable output voltage to 20V Low output noise Packages: SOT23, SOT23R, SOT25, SC59, SC59R, SOP-8L, SOT89-3L and TO92-3L Lead Free packages: SOT25, SC59, SC59R, SOT89-3L and TO92-3L (Note 1) SOT23, SOT23R, SOP-8L and TO92-3L: Available in Green Molding Compound (No Br, Sb) (Note 2) Lead Free Finish/ RoHS Compliant (Note 3) The AP432/432A are 3-terminal adjustable precision shunt regulators with guaranteed stable temperature over the applicable extended commercial temperature range. The output voltage may be set at any level greater than 1.24\/ (V REF) up to 20V merely by selecting two external resistors that act as a voltage divider network. These devices have a typical output impedance of 0.2Ω. Active output circuitry provides very sharp turn-on characteristics, making these devices excellent improved replacements for Zener diodes in many applications. The precise /- 1% reference voltage tolerance of the AP432/432A make it possible in many applications to avoid the use of a variable resistor, consequently saving cost and eliminating drift and reliability problems associated with it. Typical Application Circuit V OUT C in R1 C out AP432 R2 V OUT = (1R1/R2)VREF Precision Regulator AP432/AP432A Rev. 14 1 of 14 JULY 2009
Ordering Information AP432 X XX X - X Reference Voltage Tolerance Blank : /- 1% A : /- 0.5% Package SA : SOT23 SR : SOT23R Q : SOT25 W : SC59 R : SC59R Blank : SOP-8L Y : SOT89-3L V : TO92-3L Lead Free L : Lead Free (Note 1) G : Green (Note 2) Packing 7/13 : Tape & Reel A : Ammo Box (Note 4) Lead-free Lead-free Lead-free Lead-free Lead-free 7 /13 Tape and Reel Ammo Box Device Package Packaging Part Number Part Number (Note 5) Code (Note 3, 6) Quantity Quantity Suffix Suffix AP432(A)SAG-7 SA SOT23 3000/Tape & Reel -7 NA NA AP432(A)SRG-7 SR SOT23R 3000/Tape & Reel -7 NA NA AP432(A)QL-7 Q SOT25 3000/Tape & Reel -7 NA NA AP432(A)WL-7 W SC59 3000/Tape & Reel -7 NA NA AP432(A)RL-7 R SC59R 3000/Tape & Reel -7 NA NA AP432(A)G-13 SOP-8L 2500/Tape & Reel -13 NA NA AP432(A)YL-13 Y SOT89-3L 2500/Tape & Reel -13 NA NA AP432(A)VL-A V TO92-3L NA NA 2000/Box -A AP432(A)VG-A V TO92-3L NA NA 2000/Box -A Notes: 1. SOT25, SC59W, SC59R and SOT89-3L are Lead Free products only. 2. SOT23, SOT23R and SOP-8L are available in Green products only. 3. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 4. Ammo Box is for TO92-3L Spread Lead. 5. Suffix A denotes AP431A device. 6. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. AP432/AP432A Rev. 14 2 of 14 JULY 2009
Pin Assignment (1) SOT25 (2) SOP-8L NC 1 NC 2 CATHODE 3 5 ANODE 4 REF CATHODE ANODE ANODE 1 8 2 3 NC 4 5 7 6 REF ANODE ANODE NC (3) SC59 (4) SC59R 3 REF 3 CATHODE ANODE 1 ANODE 1 2 CATHODE 2 REF (5) SOT23 (6) SOT23R 3 REF 3 CATHODE ANODE 1 ANODE 1 2 CATHODE 2 REF (7) SOT89-3L (8) TO92-3L 3 Cathode 1 2 3 REF Anode Cathode 2 Anode 1 REF AP432/AP432A Rev. 14 3 of 14 JULY 2009
Block Diagram REF (R) VREF - Cathode (C) Anode (A) Symbol Cathode (C) REF (R) Anode (A) Absolute Maximum Ratings Symbol Parameter Rating Unit Vcv Cathode Voltage 20 V I CC Continuous Cathode Current -10 to 250 ma I REF Reference Input Current 10 ma T OP Operating Temperature -20 to 85 o C T ST Storage Temperature -65 to 150 o C P D Power Dissipation (Notes 7, 8) SOT23(R) 400 mw SOT25 550 mw SC59(R) 400 mw SOP-8L 600 mw SOT89-3L 800 mw TO92-3L 780 mw Notes: 7. T J, max =150 C 8. Ratings apply to ambient temperature at 25 C. AP432/AP432A Rev. 14 4 of 14 JULY 2009
Electrical Characteristics (T A = 25 o C, V = 5.0V, unless otherwise stated) Symbol Parameter Test Conditions Min Typ. Max Unit V V REF Reference voltage KA = V REF, AP432 1.227 1.252 1.24 V I KA = 10mA (Fig.1) AP432A 1.233 1.246 V REF ΔV REF ΔV KA Deviation of Reference input voltage over temperature (Note 9) Ratio of the change in Reference voltage to the change in Cathode voltage V KA = V REF, I KA = 10mA, Ta = Full range (Fig.1) 3.0 20 mv I KA = 10mA (Fig. 2) V KA = 20~ V REF -1.4-2.0 mv/v I REF Reference input current R1 = 10KΩ,R2 = I KA= 10mA (Fig. 2) 1.4 3.5 μa αi REF Deviation of Reference input R1 = 10KΩ,R2 = I KA = 10mA current over temperature Ta = Full range (Fig. 2) 0.4 1.2 μa I KA(MIN) Minimum Cathode current for V regulation KA = V REF (Fig.1) 0.15 0.3 ma I KA(OFF) Off-state current V KA = 36V, V REF = 0V (Fig. 3) 0.1 1.0 μa Z KA V KA = V Dynamic output impedance REF V KA = V REF ΔI (Note 10) KA = 0.1mA ~ 15mA Frequency 1KHz (Fig.1) 0.2 0.5 Ω VMAX VDEV = VMAX - VMIN VMIN TI Temperature T2 Notes: Where: 9. Deviation of reference input voltage, V DEV, is defined as the maximum variation of the reference over the full temperature range. The average temperature coefficient of the reference input voltage αv REF is defined as: ( V VDEV ) 10 (25 C) 6 ppm C REF α VREF =.... ( ) T2 T1 T2 T1 = full temperature change. αv REF can be positive or negative depending on whether the slope is positive or negative. Notes: 10. The dynamic output impedance, R Z, is defined as: Z KA ΔV = ΔI KA When the device is programmed with two external resistors R1 and R2 (see Figure 2.), the dynamic output impedance of the overall circuit, is defined as: ' Δv ZKA = ZKA (1 Δi R1 ) R2 KA AP432/AP432A Rev. 14 5 of 14 JULY 2009
Test Circuits Input IN IN I KA V KA I KA V KA V KA R1 IREF VREF R2 VREF IZ(OFF) Note:VKA=VREF(1R1/R2)IREFxR1 Fig 1. Test Circuit for V KA = V REF Fig 2. Test Circuit for V KA > V REF Fig 3. Test Circuit for Off-State Current Typical Performance Characteristics AP432/AP432A Rev. 14 6 of 14 JULY 2009
Typical Performance Characteristics (Continued) ZKA Reference Impedance (Ω) A V -Small Signal Voltage Amplification (db) 100 10 1 60 50 40 30 20 10 0 Small-Signal Voltage Amplification vs Frequency I KA =10mA T A =25 o C 1K 10K 100K 1M 10M f-frequency-hz I KA=10mA o T A=25 C Reference Impedance vs Frequency 0.1 1K 10K 100K 1M 10M f-frequency-hz 9μF - Output 15KΩ I KA 232Ω - 8.25KΩ GND Test Circuit for Voltage Amplification 1KΩ Output I KA 50Ω - GND Test Circuit for Reference Impedance IKA-Cathode Current-mA 100 90 80 70 60 50 40 30 20 STABILITY BOUNDARY CONDITIONS A V KA =V ref B V KA =5V C V KA =10V D V KA =15V Stable A B D C TA=25 o C Stable 150Ω I KA CL - Test Circuit for Curve A I KA R1=10KΩ V BATT 150Ω 10 0 0.001 0.01 0.1 1 10 C L -Load Capacitance-µF C L R2 - V BATT The areas under the curves represent conditions that may cause the device to oscillate. For curves B, C, and D, R2 and V were adjusted to establish the initial V KA and I KA conditions with C L =0.V BATT and C L were then adjusted to determine the ranges of stability. Test Circuit for Curve B, C, and D AP432/AP432A Rev. 14 7 of 14 JULY 2009
Application Examples R CL I OUT R1A R1B R R2A R2B OFF ON LED on when Low Limit< < High Limit Low Limit V (1R1B/R2B) REF High Limit V (1R1A/R2A) REF Fig. 4 Voltage Monitor Fig. 5 Delay Timer Delay = RC x ln (V IN -V REF ) I OUT = V REF / R CL Fig. 6 Current Limiter or Current Source I OUT V OUT PULSE V OUT R1 R1 RS R2 R2 I OUT = V REF / RS Fig. 7 Constant-Current Sink V OUT = (1 R1/R2) x V REF Fig. 8 Higher-Current Shunt Regulator LIMIT (1 R1/R2) x V REF Fig. 9 Crow Bar VIN R1A R1B Output ON when Low Limit < < High Limit R2A R2B VBE Low Limit V REF (1 R1B/R2B) V BE High Limit V REF (1 R1A/R2A) Fig.10 Over-Voltage / Under-Voltage Protection Circuit AP432/AP432A Rev. 14 8 of 14 JULY 2009
Marking Information (1) SC59 and SC59R ( Top View ) 3 XX Y W X 1 2 XX : Identification code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : a~z : Lead Free (2) SOT23 and SOT23R ( Top View ) 3 XX Y W X 1 2 XX : Identification code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Green (3) SOT25 5 ( Top View ) 47 XX Y W X 1 2 3 XX : Identification code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : a~z : Lead Free (4) SOP-8L ( Top View ) Logo Part Number Accuracy Blank : 2.495 1% A : 2.495 0.5% 8 5 AP432X YY WW X X 1 4 G : Green YY : Year : 08, 09,10~ WW : Week : 01~52; 52 represents 52 and 53 week X : Internal Code AP432/AP432A Rev. 14 9 of 14 JULY 2009
Marking Information (Continued) (5) SOT89-3L ( Top View ) X X Y W X 1 2 3 XX : Identification code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : Internal code a~z : Lead Free (6) TO92-3L Accuracy Blank: 2.495 1% A: 2.495 0.5% ( Top View ) AP432 X Y WW X X G : Green L : Lead Free Y : Year : 0~9 WW : Week : 01~52; 52 represents 52 and 53 week X : Internal Code Identification Code Table Notes: Device Package (Note 11) Identification Code Date Code AP432SA SOT23 D3 YM AP432ASA SOT23 D4 YM AP432SR SOT23R D7 YM AP432ASR SOT23R D8 YM AP432Q SOT25 B7 YM AP432AQ SOT25 B8 YM AP432W SC59 B3 YM AP432AW SC59 B4 YM AP432R SC59R B5 YM AP432AR SC59R B6 YM AP432Y SOT89 B1 YM AP432AY SOT89 B2 YM 11. For packaging details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. AP432/AP432A Rev. 14 10 of 14 JULY 2009
Package Information (All Dimensions in mm) (1) Package type: SOT25 (2) Package Type: SC59 and SC59R 0.35/0.50 TOP VIEW 1.50/ 1.70 2.70/ 3.00 1.90 2.90/3.10 1.00/ 1.30 0.10/0.20 0.013/0.10 0.95 0.35/0.55 0 /8 AP432/AP432A Rev. 14 11 of 14 JULY 2009
Package Information (Continued) (3) Package Types: SOT23 and SOT23R (4) Package Type: SOP-8L 3.85/3.95 5.90/6.10 0.10/0.20 0.254 Gauge Plane Seating Plane 0.62/0.82 Detail "A" 7 ~9 0.35max. 45 7 ~9 1.30/1.50 1.75max. 0.15/0.25 Detail "A" 0 /8 1.27typ 0.3/0.5 4.85/4.95 8x-0.60 5.4 6x-1.27 8x-1.55 Land Pattern Recommendation (Unit: mm) AP432/AP432A Rev. 14 12 of 14 JULY 2009
Package Information (Continued) (5) Package Type: SOT89-3L 1.40/1.75 Typ 1.60 1.7 0.80/ 1.20 2.35/2.60 Typ 2.48 3.94/4.25 0.4 1.9 2.7 8 0 (2x) 2.90/3.10 Typ 3.00 4.40/4.60 Typ 4.50 0.9 1.5 Land Pattern Recommendation (Unit: mm) 5 0 (2x) 1.40/1.60 Typ 1.50 1.3 1.45/1.55 Typ 1.50 0.36/0.48 0.41/0.53 Typ 0.42 Typ 0.47 0.36/0.48 Typ 0.42 0.35/0.43 Typ 0.39 (6) Package Type: TO92-3L for Ammo pack AP432/AP432A Rev. 14 13 of 14 JULY 2009
IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright 2009, Diodes Incorporated www.diodes.com AP432/AP432A Rev. 14 14 of 14 JULY 2009