Pipe Hangers, Supports and Accessories Base Price List. v 04302018.1
v 04302018.1 pipe hangers & supports, strut & strut accsessories base price list Filling industry s needs for pipe hangers, supports, strut, custom fabrication and metal stampings. Stocking stainless steel hangers, strut and accessories in Type 304 and Type 316. Offering same day shipping for truck and air freight shipments. Shipping material packaged and tagged per the customer s instructions. Offering order transactions via EDI technology. Coatings and finishes include: Electro-galvanizing Hot dip galvanizing Copper plating Copper epoxy coating Chrome plating Plastic coating Epoxy Coating Multiplier: Local Sales Representative: Factory contact: 180 OLCOTT STREET MANCHESTER, CT 06040 TELEPHONE: (860) 647-1431 USA: 1-800-243-4844 FAX: (860) 647-1160 ORDERS: ORDERS@EMPIREINDUSTRIES.COM QUOTES: QUOTES@EMPIREINDUSTRIES.COM EMPIREINDUSTRIES.COM v 04302018.1 empire industries, inc. 1
TERMS OF SALE AGREEMENTS: All agreements are subject to strikes, accidents or other causes beyond our control. Prices and designs are subject to change without notice. TAXES: The buyer is liable for any Federal or State taxes imposed on the seller. WARRANTY: We guarantee to replace, or at our option, to repair any material which we find in our sole discretion to be defective in material or workmanship; provided that a claim and proof thereof is made in writing to us within thirty (30) days after purchaser s receipt. In no event shall we be liable for transportation to or from our factory, installation, adjustments or any expenses or damages which may arise in loss of use, and the foregoing shall be the purchaser s sole remedy hereunder. No other warranty or guarantee of any kind is made, expressed or implied. Products sold but not manufactured by Empire are not warrantied by Empire; however, to the extent possible, Empire will pass through to the purchaser any supplier s warranty. CLAIMS: No claims for shortages allowed unless made in writing within ten (10) days of receipt of goods. All material sent out will be carefully counted and packed. Claims for goods damaged or lost in transit should be made to the carrier as our responsibility ceases on delivery to the carrier. LIABILITY FOR MISUSE: We shall not be liable for damages to property or persons due to improper installation of our material or through attempts to utilize the material under conditions which exceed the designed capabilities. Purchaser agrees to indemnify and hold Empire Industries, INC harmless from any and all claims, liabilities, damages, costs, and expenses asserted against us or incurred by us because of injuries to persons or damages to property resulting from the improper installations or misuse of the material. RETURNS: Permission to return standard stocked merchandise must be obtained in writing. Credit will be issued subject to the following: 1. Return freight charges must be prepaid. 2. All material must be in first-class condition on arrival at our plant; if not, reconditioning costs will be deducted from the credit memo. 3. Return good authorizations (RGA s) will require a signed, authorized RGA form from the party returning the material. Any items that deviate from the signed RGA form will be deducted from the credit, or shipment may be refused. 4. Credit will be allowed on the basis of the price charged less a minimum handling charge of 25%, and less any outbound freight allowed or paid by Empire. 5. Materials are NOT RETURNABLE after 60 days beyond date of invoice. 6. Credits received for returned goods must be used within 12 months beyond date of credit invoice. SPECIAL ORDERS: Orders quoted special with non-standard material are not subject to cancellation or return unless such terms are agreed upon. MILL TEST REPORT POLICY: In most cases, Empire Industries can furnish a Mill Test Report (MTRs) and/or Certificate of Compliance (C of Cs) upon receipt of a formal purchase order. If an MTR (or C of C) is to be required, Empire strongly suggests that we are made aware of such at the time of quotation. MTRs must be formally requested on the original purchase order and will not be available for product that has already been shipped. Please be advised that individual MTRs and/ or C of Cs hold a minimum charge of $25.00 each. Such charge will be applied to the corresponding invoice of the product purchased. MINIMUM INVOICE: $50.00 plus transportation. INTEREST CHARGE: Any amount not paid within terms by the customer shall bear interest at the maximum rate permitted by law, not to exceed 1 1/2% per month. FREIGHT ALLOWANCE: All prices are F.O.B. point of shipment. Full freight allowed orders are negotiated on a regional basis (Contact your local manufacturers representative or the factory direct). 2 empire industries, inc. v 04302018.1
FIG. 10J j-hanger Electro-Galvanized: Imported (10JGI) Electro-Galvanized: Imported, 3/16 Felt-lined (10JGIFL) T-304 Stainless (10JSS) T-316 Stainless (10JSX) FIG. 11 Designed for the suspension of non-insulated, stationary pipe lines. Complies with Manufactures Standardization Society (MSS) SP-58 & SP-69 (Type 5) Specify figure number, finish and pipe size. Stainless steel hangers are recommended for applications where protection from a corrosive environment is required. adjustable clevis hanger, standard 1/2 4.14 E.G. SS SX GIFL 100 3/4 4.30 100 1 4.38 100 1-1/4 4.61 100 1-1/2 5.08 100 2 6.56 50 2-1/2 12.50 50 3 13.13 25 3-1/2 18.44 25 4 19.38 25 5 39.93 25 6 47.11 10 8 57.51 10 10 66.64 BULK Plain Carbon Steel (11B) Hot-Dip Galvanized (11HDG) T-316 Stainless (11SX) Electro-Galvanized (11G) T-304 Stainless (11SS) Pipe Gard (11PG) - Please contact factory for details. Electro-Galvanized, Imported: 1/2-12 (11GI) Electro-Galvanized, 3/16 thick Felt-Lined, Imported: 1/2-8 (11GIFL) Hot-Dip Galvanized, Imported: 2-3, 4-6, 8-12 (11HDGI) Designed for the suspension of non-insulated, stationary pipe lines. U.L. - U.L.C. listed (sizes 2-1/2-8 excluding 7 ) and FM approved (3/4-2 galv only. 2-1/2-8 plain and galv.). Complies with Federal Specification WW-H-171-E (Type# 1), A-A-1192 A (Type# 1) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 1). Specify figure number, material, finish and pipe size. For sizes 20 and larger a spacer sleeve is added over the cross bolt. Upper locknut must be tightened securely to assure proper hanger performance. Stainless steel hangers are recommended for applications where protection from a corrosive environment is required. E.G. H.D.G. SS SX GI HDGI GIFL 1/2 2.44 2.95 3.86 21.06 26.45 2.61 2.63 3/4 2.44 3.01 3.86 22.76 28.49 2.67 2.68 100 1 2.55 3.12 4.03 24.12 30.54 2.78 2.84 100 1-1/4 2.95 3.63 4.57 26.16 32.58 3.24 3.15 100 1-1/2 2.95 4.03 4.65 29.40 36.32 3.63 3.41 100 2 3.18 4.60 5.28 33.77 42.96 3.75 4.77 50 2-1/2 5.96 8.74 10.27 64.08 79.57 7.44 9.24 50 3 6.70 10.05 11.58 76.68 99.72 8.12 10.41 25 3-1/2 9.08 13.51 18.39 -- 135.48 -- -- 25 4 8.51 12.26 15.32 104.66 136.44 9.76 13.82 25 5 13.05 17.82 24.06 159.32 203.42 16.01 21.67 25 6 17.08 24.41 29.29 197.74 246.44 21.68 26.36 10 7 27.87 43.82 54.83 -- -- -- -- 10 8 25.37 37.12 46.71 283.61 380.38 32.18 42.05 10 10 49.38 69.58 86.95 517.62 675.06 59.94 79.29 BULK 12 62.49 88.14 112.38 656.73 852.60 70.44 101.13 BULK 14 108.52 138.37 227.14 719.28 1,043.70 -- -- BULK 16 150.46 195.30 324.76 1,176.00 1,705.20 -- -- BULK 18 198.36 250.01 -- -- -- -- BULK 20 386.34 504.17 -- -- -- -- BULK 24 546.00 672.74 -- -- -- -- BULK 30 770.08 944.43 -- -- -- -- BULK excluding: 11GI 11GIFL 11HDGI 100 v 04302018.1 empire industries, inc. 3
FIG. 11DIP clevis hanger for awwa ductile iron and pvc c-900 pipe H.D.G. SS SX Plain Carbon Steel (11DIPB) Hot-Dip Galvanized (11DIPHDG) T-304 Stainless (11DIPSS) T-316 Stainless (11DIPSX) Designed for the suspension of stationary AWWA ductile iron pipe and PVC C-900 pipe. Complies with Federal Specifications WW-H-171-E (Type# 1), A-A-1192 A (Type# 1), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 1). Specify figure number, material, finish and pipe size. For sizes 8 and larger a spacer sleeve is added over the cross bolt. Upper locknut must be tightened securely to assure proper hanger performance. Stainless steel hangers are recommended for applications where protection from a corrosive environment is required. FIG. 11F flat top clevis hanger 3 16.91 24.35 25 4 16.91 24.69 25 6 34.17 48.64 25 8 63.23 100.74 10 10 107.44 158.58 BULK 12 134.63 196.38 BULK 14 290.20 BULK 16 299.45 BULK 18 499.18 BULK 20 902.38 BULK 24 1,045.91 BULK Plain Carbon Steel (11FB) Hot-Dip Galvanized (11FHDG) T-316 Stainless (11FSX) Electro-Galvanized (11FG) T-304 Stainless (11FSS) Designed for the suspension of non-insulated stationary pipe where space is limited. Complies with MSS SP-58 and SP-69 (Type #1). Specify figure number, finish and pipe size. Upper locknut must be tightened securely to assure proper hanger performance. FIG. 11V v bottom clevis hanger E.G. H.D.G. SS SX 2 18.79 24.01 2-1/2 25.65 28.21 50 3 23.72 29.68 25 3-1/2 57.78 -- 25 4 27.36 35.25 25 5 36.89 49.21 25 6 52.56 60.84 10 8 76.11 85.87 10 50 Plain Carbon Steel (11VB) Electro-Galvanized (11VG) T-304 Stainless (11VSS) T-316 Stainless (11VSX) Designed for the suspension of flexible plastic pipe lines. Used in conjunction with figure #12 channel. Specify figure number, finish and pipe size Hanger and channel sold separately. Upper locknut must be tightened securely to assure proper hanger performance. NO. 1 1/2-2 7.89 10.10 2 2-1/2-4 17.14 23.44 3 5-6 51.65 4 7-8 76.11 5 10 118.28 E.G. SS SX 4 empire industries, inc. v 04302018.1
FIG. 11WS clevis with welded shield HAGNER E.G. SS SX SHIELD I.D. excluding: 11WSGI Plain Carbon Steel (11WSB) Electro-Galvanized (11WSG) T-304 Stainless (11WSSS) T-316 Stainless (11WSSX) Electro-Galvanized: Import (11WSGI) Designed for the suspension of staionary insulated pipe lines. Insulation protection shield is spot welded in place Specify figure number, finish and hanger size. To determine proper hanger size, use hanger selection guide below. Upper locknut must be tightened securely to assure proper hanger performance. FIG. 11X 1-1/2 23.61 adjustable clevis hanger with extended bottom 1-7/8 2 24.01 2-3/8 2-1/2 29.51 2-7/8 3 33.26 3-1/2 3-1/2 36.55 4 4 37.29 4-1/2 5 48.75 5-5/8 6 57.38 6-5/8 7 78.78 7-5/8 8 81.45 8-5/8 10 138.26 10-3/4 12 159.37 12-3/4 14 232.02 14 16 311.71 16 18 20 19 24 21 18 E.G. SS SX Plain Carbon Steel (11XB) Hot-Dip Galvanized (11XHDG) T-316 Stainless (11XSX) Electro-Galvanized (11XG) T-304 Stainless (11XSS) Designed for the suspension of non-insulated stationary pipe lines. The bottom section of the hanger is elongated to allow for easier installation of insulation. Complies with Federal Specifications WW-H-171-E (Type# 1), A-A-1192 A (Type# 1), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 1). Specify figure number, finish and pipe size Upper locknut must be tightened securely to assure proper hanger performance. FIG. 12 v-channel 1/2 16.01 18.84 50 3/4 16.12 19.07 50 1 16.23 19.24 50 1-1/4 16.69 20.49 50 1-1/2 17.31 21.00 25 2 20.55 21.68 25 2-1/2 24.58 29.00 25 3 26.79 33.15 20 4 33.60 44.95 10 5 45.58 63.68 10 6 60.84 79.80 10 8 95.35 123.11 10 10 135.65 195.15 BULK 12 167.09 250.07 BULK Pre-Galvanized Carbon Steel (10 lengths) (12) Designed for the support of plastic or other flexible pipe systems. Use with FIG. 11V V bottom clevis hanger. Hangers should be placed as close to channel joints as possible. Specify figure number and size number. NO. E.G. 1 1/2-2 76.00 2 2-1/2-4 132.30 v 04302018.1 empire industries, inc. 5
FIG. 13I weldless eyenut Plain Carbon Steel (13BI) T-304 Stainless (13SSI) Plain Carbon Steel, Domestic (13B) Hot-Dip Galvanized, Domestic(13HDG) Hot-Dip Galvanized (13HDGI) T-316 Stainless, Domestic (13SX) Plain Carbon Steel, L.H. Threads (13LB) Hot-Dip Galvanized, L.H. Threads (13LHDG) T-316 Stainless, L.H, Threads (13LSX) Designed for use on high temperature piping applications. Complies with Federal Specifications WW-H-171-E (Type# 17), A-A-1192 A (Type# 17), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 17). Specify figure number, finish and rod size. Hot Dip Galvanized eye nuts are not tapped oversize. All sizes of domestic eye nuts are priced on application. H.D.G. SS 3/8 11.46 16.80 100 1/2 11.46 16.80 100 5/8 21.57 31.78 50 3/4 21.57 31.78 50 7/8 54.60 80.03 10 1 54.60 80.03 10 1-1/8 159.88 276.24 10 1-1/4 159.88 276.24 5 1-1/2 188.15 293.26 5 FIG. 21 / 21L steel c-clamp Plain Carbon Steel (21B) Plain Carbon Steel W/ Locknut (21LB) Electro-Galvanized W/ Locknut (21LG) T-304 Stainless Steel W/ Locknut (21LSS) T-316 Stainless Steel W/ Locknut (21LSX) Electro-Galvanized (21G) Designed for attaching hanger rod to the bottom flange of a beam. Features the ribbed design for added strength. Hardened steel cup point set screw secures clamp to beam. UL - U.L.C. listed 3/8 and 1/2 (1/2 for 4 IPS max) with locknut only. FM approved (excluding 21LSS and 21LSX) for 3/8 only with and without locknut. Complies with Federal Specification WW-H-171-E (Type# 23), A-A-1192 A (Type# 23), Manufacturers Standard Society SP-58 and MSS SP-69 (Type# 23). Specify figure number, finish and rod size. See MSS SP-69 for proper set screw torque recommendations. Full carton quantities only 3/8 and 1/2. FIG. 21 C-CLAMP E.G. SS SX 3/8 4.14 5.51 100 1/2 4.37 6.24 100 -- -- 5/8 9.48 11.92 50 3/4 14.36 17.59 50 FIG. 21L C-CLAMP W/ LOCKNUT E.G. SS SX 3/8 4.37 5.28 28.95 41.43 100 1/2 4.54 6.13 31.44 43.76 100 5/8 12.37 15.10 69.58 107.89 50 3/4 15.95 19.64 111.75 178.84 50 7/8 -- -- -- 6 empire industries, inc. v 04302018.1
FIG. 21R retaining strap Plain Carbon Steel (21RB) Electro-Galvanized (21RG) T-304 Stainless Steel (21RSS) T-316 Stainless Steel (21RSX) Designed for use with figure FIG. 21, FIG. 21L (3/8-3/4 ) and FIG. 23L (3/8 and 1/2 ) to eliminate movement of the beam clamp due to vibration. FM Approved (3/8 ) Specify figure number, finish and length Add 2 minimum to flange width to determine length. FIG. 22R retaining strap E.G. SS SX 4-1/2 4.82 6.30 100 6 4.88 6.36 100 8 4.94 6.53 100 10 5.05 6.64 100 12 5.90 7.44 100 14 7.21 9.25 100 Plain Carbon Steel (22RB) T-304 Stainless Steel: 3/8-1/2, 13ga x 1 (22RSS) T-316 Stainless Steel: 3/8-1/2, 13ga x 1 (22RSX) Designed for use with FIG. 61 and FIG. 62. Specify figure number, finish and length Electro-Galvanized (22RG) Add 2 minimum to flange width to determine length. Custom lengths available. 3/8 & 1/2 rod sizes provided on same strap. FIG. 23L malleable iron c-clamp with locknut LENGTH (IN.) 3/8 PRICE EACH - 1/2 5/8 3/4 7/8 4-1/2 3.58 3.58 4.43 4.48 4.88 6 3.80 3.80 4.60 4.65 5.11 8 3.97 3.97 4.99 5.05 5.62 10 4.54 4.54 5.28 5.39 6.36 12 5.16 5.16 6.13 6.19 7.21 14 5.96 5.96 6.92 6.70 9.25 Plain Ductile Iron (23LB) Electro-Galvanized (23LG) Designed for attaching hanger rod to the bottom flange of a beam. U.L. - U.L.C. listed and FM approved 3/8 and 1/2 ONLY. Complies with Federal Specification WW-H-171-E (Type# 23), A-A-1192 A (Type# 23) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 23). Specify figure number, finish and rod size. See MSS SP-69 for proper set screw torque recommendations E.G. 3/8 4.26 6.36 100 1/2 5.22 6.81 100 5/8 8.34 13.39 50 3/4 11.07 17.42 50 v 04302018.1 empire industries, inc. 7
FIG. 24L purlin clamp Plain Ductile Iron (24LB) Electro-Galvanized (24LG) Designed for use with large-lip steel Purlin beams. Specify figure number and finish. See MSS SP-69 for proper set screw torque recommendations E.G. 3/8 21.17 25.71 20 FIG. 25L extended c-clamp with locknut Plain Malleable Iron (25LB) Designed for attachment to beams where flange thickness does not exceed 3/4 and where it is desired to have the rod support offset from the beam. Specify figure number and finish. See MSS SP-69 for proper set screw torque recommendations. 3/8 3/8 33.37 50 FIG. 26 eye rod Plain Carbon Steel (26B) Hot-Dip Galvanized (26HDG) Electro-Galvanized (26G) T-304 Stainless Steel (26SS) INCHES 3/8 1/2 5/8 3/4 7/8 1 T-316 Stainless Steel (26SX) Plain Carbon Steel, Welded (26WB) Electro-Galvanized, Welded (26WG) 8-72 Hot-Dip Galvanized, Welded (26WHDG) T-304 Stainless Steel, Welded (26WSS) T-316 Stainless Steel, Welded (26WSX) Designed for for use in hanger assemblies and supports. Specify figure number, finish and rod size. Made to order. Min order to be $100.00 net / size. Other lengths, rod diameters and thread lengths available upon request. 8 empire industries, inc. v 04302018.1
FIG. 31 band hanger E.G. P.C. SS SX Plain Carbon Steel (31B) Plastic Coated (31PC) T-316 Stainless (31SX) Electro-Galvanized (31G) T-304 Stainless (31SS) Pipe Gard (31PG) - Please contact factory for details. Designed for the suspension of non-insulated stationary pipe lines. The plastic coated band hanger protects the pipe from the steel surface of the hanger and is designed to reduce noise, vibration and prevents electrolysis between pipe and the hanger. Stainless steel hangers are recommended for applications where protection from corrosive environments is needed. Complies with Federal Specification WWH-171-E (Type# 7), A-A-1192A (Type# 7), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 7). Specify figure number, finish and pipe size. Upper locknut must be tightened securely to assure proper hanger performance. FIG. 31CT band hanger for copper tubing 3/8 1.53 2.21 7.66 -- -- 100 1/2 1.53 2.21 7.66 14.30 22.76 100 3/4 1.59 2.27 7.83 14.47 22.99 100 1 1.59 2.55 8.12 15.32 23.84 100 1-1/4 1.65 2.78 8.51 16.40 25.31 100 1-1/2 1.70 3.12 8.74 17.76 27.53 100 2 1.76 3.69 11.01 19.24 29.74 100 2-1/2 3.29 5.51 12.83 32.18 49.89 50 3 3.52 6.19 14.08 33.66 52.16 50 3-1/2 5.16 8.74 21.45 -- -- 50 4 5.28 8.74 21.57 39.62 61.41 50 5 6.02 10.95 29.74 48.53 75.20 BULK 6 16.80 27.92 58.52 81.73 122.20 BULK 8 24.18 36.27 86.38 94.05 145.75 BULK excluding: 31CTI Copper Plated Carbon Steel (31CTP) Copper Epoxy Coated Copper Gard: Imported (310CTI) Designed for the suspension of non-insulated stationary pipe. Complies with Federal Specifications WW-H-171-E (Type# 7), A-A-1192 A (Type# 7), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 7). Specify figure number, finish and tube size. FIG. 34, 35 & 36 Upper locknut must be tightened securely to assure proper hanger performance. COPPER-GARD products offer superior corrosion protection due to the epoxy coating over electro-galvanized steel. The alternative, copper plating that has been done historically, is for identification purposes only and is not intended for corrosion protection. Refer to MSS-SP58 13.3. vibration spring-flex and neoprene hanger TUBING PLATED (CTP) COATED (CTI) 1/2 2.04 1.59 100 3/4 2.10 1.59 100 1 2.16 1.70 100 1-1/4 2.33 1.93 100 1-1/2 2.44 2.04 100 2 2.50 2.16 100 2-1/2 5.28 4.03 50 3 5.45 4.14 50 3-1/2 9.65 9.08 50 4 9.71 9.14 50 5 14.64 12.32 25 6 17.88 15.21 25 FIG. 34 FIG. 35 FIG. 36 Painted Carbon Steel Housing with Neoprene Rubber Element (34) Specify figure number, isolator size, rod size and load. Painted Carbon Steel Housing with Steel Spring (35) Specify figure number, isolator size, rod size and load. Painted Carbon Steel Housing and spring with neoprene rubber element (36) Specify figure number, isolator size, rod size and load. v 04302018.1 empire industries, inc. 9
FIG. 37 anti-vibration hanger mount Electro-Galvanized W/ Elastomer Element (37AVHM) Designed to isolate both noise and vibration for piping or suspended equipment. Specify figure number. Can be used with threaded rods up to 3/8. ITEM NUMBER 37AVHM50 37AVHM100 PRICE EACH FIG. 40HS handy split ring hanger Electro-Galvanized with EPDM Insulation Liner (40HS) Designed for the suspension of insulated and non-insulated pipe lines. Complies with Federal Specification WWH-171-E (Type# 25), A-A-1192A (Type# 12), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 12). Specify figure number and CT or IPS Size. The Handy Split hinge device allows single handed installation. UV resistant EPDM ubber provides noise reduction. Temperature range is from -50 F through 230 F. FIG. 41A hanger flange plate PART NO. IPS TUBE CT PRICE EACH 40HS0001 1/4 3/8 3.80 50 40HS0002 3/8 1/2 3.80 50 40HS0003 -- 5/8 3.80 50 40HS0004 1/2 3/4 4.09 50 40HS0005 3/4 1 4.31 50 40HS0006 1 1-1/4 4.54 50 40HS0007 1-1/4 1-1/2 5.68 25 40HS0008 1-1/2 -- 7.21 25 40HS0009 -- 2 6.13 25 40HS0010 2 -- 9.82 25 40HS0011 -- 2-1/2 9.31 10 40HS0012 2-1/2 -- 17.37 10 40HS0013 -- 3 26.51 10 40HS0014 3 -- 26.51 10 40HS0015 -- 3-1/2 26.51 10 40HS0016 3-1/2 4 31.05 10 40HS0017 4 -- 31.05 10 E.G. COPPER EPOXY COATED SOLID BRASS SS SX 3/8 2.21 2.61 2.78 14.47 33.60 40.98 100 1/2 3.52 4.09 3.86 -- 36.78 46.20 100 Plain Malleable Iron (41AB) Chrome Plated (41ACR) Solid Brass (41ASB) T-316 Stainless (41ASXI) Electro-Galvanized (41AG) Copper Epoxy Coated (41ACT) T-304 Stainless (41ASSI) Designed for attaching hanger rod to wood beams, ceilings, walls and floor. Specify figure number, finish and rod size. Stainless flange plates are reccommended for applications where protection from a corrosive environment is required. COPPER-GARD Products offer superior corrosion protection due to the epoxy coating over electro-galvanized material. The alternative copper plating that has been done traditionally is for identityfication purposes and is not intended for corrosion protection. Refer to MSS SP-58, 13.3. 10 empire industries, inc. v 04302018.1
FIG. 41OD split ring extension hanger for o.d. tubing stainless OD SSI SXI T-304 Stainless (41ODSSI) T-316 Stainless (41ODSXI) Designed for the suspension of non-insulated stationary pipe lines, horizontally or vertically. Complies with Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 12). Specify figure number, finish and pipe size. Stainless steel hangers are recommended for applications where protection from a corrosive environment is required. FIG. 41 split ring extension hanger 3/8 100 1/2 100 3/4 100 5/8 45.86 53.46 100 7/8 47.28 54.94 100 1-1/8 51.48 59.31 100 1-3/8 57.04 65.10 100 1-5/8 59.82 67.99 100 2-1/8 77.93 95.52 50 2-5/8 166.98 196.78 50 3-1/8 190.59 230.94 25 4-1/8 211.76 260.46 25 E.G. CHROME PLATED Plain Malleable Iron (41B) Chrome Plated (41CR) Electro-Galvanized (41G) Designed for the suspension of non-insulated stationary pipe, horizontally or vertically. Complies with Federal Specification WWH-171-E (Type# 25), A-A-1192A (Type# 12), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 12). Specify figure number, finish and pipe size. Split ring extention hangers with hinged design available in 3/8-4 (41H). FIG. 41CT split ring for copper tubing 1/2 2.84 3.24 100 3/4 2.95 3.41 100 1 3.06 3.52 100 1-1/4 3.86 4.20 50 1-1/2 4.43 4.94 50 2 5.22 5.90 50 2-1/2 Hinge Only Hinge Only -- 3 Hinge Only Hinge Only -- 4 Hinge Only Hinge Only -- Copper Epoxy Coated (COPPER-GARD) Malleable Iron (41CT) Solid Brass (41CTSB) Designed for the suspension of non-insulated stationary copper tubing, horizontally or vertically. Complies with Federal Specification WWH-171-E (Type# 25), A-A-1192A (Type# 12), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 12). Specify figure number, finish and pipe size. Copper epoxy coated (COPPER-GARD). COPPER-GARD products offer superior corrosion protection due to the epoxy coating over electro-galvanized material. TUBING COPPER EPOXY COATED SOLID BRASS 1/2 2.84 13.00 100 3/4 2.89 13.74 100 1 2.95 14.87 100 1-1/4 3.29 -- 50 1-1/2 3.97 -- 50 2 4.65 -- 50 2-1/2 Hinge Only -- -- 3 Hinge Only -- -- 4 Hinge Only -- -- v 04302018.1 empire industries, inc. 11
FIG. 41H split ring extension hanger, hinge design Plain Malleable Iron (41HB) Electro-Galvanized (41HG) Designed for the suspension of non-insulated stationary pipe lines horizontally or vertically. Complies with Federal Specification WWH-171-E (Type# 25), A-A-1192A (Type# 12), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 12). Specify figure number, finish and pipe size FIG. 41HCT E.G. CHROME PLATED 3/8 2.70 3.10 100 1/2 2.70 3.10 100 3/4 2.80 3.25 100 1 2.90 3.35 100 1-1/4 3.70 4.00 50 1-1/2 4.20 4.70 50 2 4.95 5.60 50 2-1/2 13.20 16.45 25 3 18.30 19.50 25 4 23.15 25.75 25 split ring extension hanger, hinge design for copper tubing Copper Epoxy Coated (COPPER-GARD) Malleable Iron (41HCT) Designed for the suspension of non-insulated stationary copper tubing, horizontally or vertically. Complies with Federal Specification WWH-171-E (Type# 25), A-A-1192A (Type# 12), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 12). Specify figure number, finish and tube size. COPPER-GARD products offer superior corrosion protection due to the epoxy coating over electro-galvanized material. The alternative copper plating that has been done historically identifies the product and is not intended for protection. Refer to MSS SP58, 13.3. TUBING COPPER EPOXY COATED 1/4 2.84 100 3/8 2.84 100 1/2 2.84 100 3/4 2.89 100 1 2.95 100 1-1/4 3.29 50 1-1/2 3.97 50 2 4.65 50 2-1/2 12.94 25 3 15.78 25 4 22.08 25 FIG. 41SSI/SXI t-304 & t-316 stainless steel split ring extension hanger SS SX T-304 Stainless (41SSI) T-316 Stainless (41SXI) Designed for the suspension of non-insulated stationary pipe lines, horizontally or vertically. Complies with Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 12). Specify figure number, material and pipe size. Stainless steel hangers are recommended for applications where protection from a corrosive environment is required. 3/8 42.00 49.15 100 1/2 43.31 50.51 100 3/4 44.61 51.88 100 1 48.58 55.96 100 1-1/4 53.81 61.41 100 1-1/2 56.42 64.14 50 2 73.50 90.07 50 2-1/2 157.50 185.65 50 3 189.68 217.89 50 4 220.16 251.94 50 12 empire industries, inc. v 04302018.1
FIG. 47 eye socket Plain Malleable Iron (47B) Electro-Galvanized (47G) Designed for attaching hanger rod to various types of hangers. Complies with Federal Specification WWH-171E (Type# 16), A-A-1192A (Type# 16), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 16). Specify figure number, finish and rod size. FIG. 48 riser clamp for plastic pipe E.G. 1/4 2.33 2.55 100 3/8 2.44 2.72 100 1/2 3.01 3.41 100 5/8 4.48 6.58 50 3/4 7.61 9.71 50 7/8 15.78 18.90 50 Plain Carbon Steel (48B) Plastic Coated (48PC) Electro-Galvanized (48G) Designed for the support of plastic DWV pipe. Complies with Federal Specification WWH-171E (Type# 8), A-A-1192A (Type# 8), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 8). Specify figure number, finish and pipe size. FIG. 50 standard riser clamp E.G. PLASTIC COATED 1-1/2 6.64 8.85 17.88 50 2 6.92 9.14 19.01 50 3 8.34 10.22 21.62 50 4 8.85 12.60 26.79 50 Plain Carbon Steel (50B) Hot-Dip Galvanized (50HDG) Electro-Galvanized (50G) Plastic Coated (50PC) T-304 Stainless (50SS) T-316 Stainless (50SX) Pipe Gard (50PG) - Please contact factory for details. T-304 Stainless for DIP sizes (50DIPSS) T-316 Stainless for DIP sizes (50DIPSX) Designed for supporting and stabilizing vertical pipe runs. U.L. - U.L.C. listed (sizes 2-8 ). Complies with Federal Specification WW- H-171-E (Type# 8), A-A-1192 A (Type# 8) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 8). Specify figure number, finish and pipe size. Available in IPS (50) and Ductile Iron Pipe (50DIP) Sizes. Plastic coated riser clamps are completely plastic coated with zinc plated hardware. The plastic coating prevents pipe from coming in contact with the clamp and is designed to reduce noise, vibration and prevent electrolysis between pipe and clamp. Stainless steel riser clamps are recommended for applications where protection from a corrosive environment is required. - IPS E.G. H.D.G. SS SX PLASTIC COATED 1/2 7.61 10.16 12.66 55.62 77.87 24.18 50 3/4 7.61 10.16 12.66 58.46 81.79 24.18 50 1 7.61 10.22 13.05 61.69 86.38 24.69 50 1-1/4 8.97 11.58 13.39 66.69 93.36 27.53 50 1-1/2 8.91 12.03 13.85 69.47 97.22 28.83 50 2 8.97 12.38 14.08 75.60 105.85 29.12 50 2-1/2 11.64 15.66 21.96 96.60 125.77 40.18 25 3 12.03 16.69 22.02 99.21 128.89 42.96 25 3-1/2 21.06 26.85 36.32 -- -- -- 25 4 14.81 22.02 26.16 113.85 149.72 50.80 25 5 22.19 32.69 36.70 181.51 254.10 76.62 10 6 24.12 34.39 37.57 188.89 264.37 83.72 10 8 48.64 69.87 82.01 344.12 481.81 171.97 BULK 10 69.07 94.16 128.44 560.70 734.38 12 110.90 187.01 14 145.86 234.35 BULK BULK BULK 16 264.60 384.36 BULK -- 18 301.09 468.75 BULK -- -- 20 359.89 534.36 BULK 24 464.50 812.64 BULK 30 BULK v 04302018.1 empire industries, inc. 13
FIG. 50CT riser clamp for copper tubing Copper Plated Carbon Steel (50CT) Copper Epoxy Coated Electro-Galvanized Steel COPPER-GARD: Imported (50CTI) Designed for supporting and stabilizing vertical tubing runs. Complies with Federal Specification WW-H-171-E (Type# 8), A-A- 1192A (Type# 8), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 8). Specify figure number, finish and pipe size. excluding: 50CTI COPPER-GARD products offer superior corrosion protection due to the epoxy coating over electro-galvanized steel. COPPER PLATED COPPER EPOXY COATED 1/2 8.46 7.26 50 3/4 8.57 7.32 50 1 9.54 8.06 50 1-1/4 10.67 9.31 50 1-1/2 11.81 10.73 50 2 14.25 12.54 25 2-1/2 15.95 14.76 25 3 17.42 16.74 25 3-1/2 29.00 22.53 25 4 25.88 25.71 25 5 53.81 39.45 10 6 63.34 44.04 10 FIG. 50H heavy duty riser clamp Plain Carbon Steel (50HB) Hot-Dip Galvanized (50HHDG) T-304 Stainless (50HSS) T-316 Stainless (50HSX) Designed for supporting and stabilizing vertical pipe runs. Complies with MSS SP-58 TYPE 42. Specify figure number, finish and pipe size. Shear lugs included. (Shear lugs carry load). Sizes 2-8 include 2 lugs Sizes 10-20 include 4 lugs FIG. 50SA short arm riser clamp 2 2-1/2 3 4 5 6 8 10 12 14 16 18 20 24 ALL FINISHES BULK E.G. Plain Carbon Steel (50SAB) Electro-Galvanized (50SAG) Designed for supporting and stabilizing vertical pipe runs. Overall length of clamp is shorter than standard to accommodate field requirements. Complies with Federal Specification WWH-171-E (Type# 8), A-A-1192A (Type# 8), Manufacturers Standardization Society SP-58 and MSS SP-69 (Type# 8). Specify figure number, finish and pipe size. 3/4 12.60 100 1 12.60 100 1-1/4 12.83 50 1-1/2 13.00 50 2 13.28 50 2-1/2 14.87 25 3 15.04 25 3-1/2 25 4 18.28 25 5 34.68 15 6 35.19 15 14 empire industries, inc. v 04302018.1
FIG. DPCSS manhole drop pipe clamp 4 6 8 10 12 SDR-35 DIP/C-900 IPS T-304 Stainless (DPCSS) Designed for easy installation and support of manhole drop pipe. Specify figure number, size 4-12, SDR-35, DIP/C-900 or IPS. *Mounting Kit (DPCSSKIT) also available *T-304 STAINLESS MOUNTING KIT INCLUDES QUANTITY DESCRIPTION PART # 2 T-304 DROP-IN ANCHOR, 3/8 77SS0038 2 T-304 ALL THREAD STUD, 3/8 X 10 68SS0381000K 4 T-304 STAINLESS HEX NUT, 3/8 56SS0038K 4 T-304 STAINLESS WASHER 52DD0038K KIT PART # DPCSSKIT FIG. 51 rod coupling Plain Carbon Steel (51B) Electro-Galvanized (51G) T-304 Stainless (51SS) T-316 Stainless (51SX) Designed for connecting two lengths of rod with equal diameters. Specify figure number, finish and rod size. FULL CARTON QUANTITIES ONLY ON S 3/8 AND 1/2. E.G. SS SX 1/4 -- 2.04 11.98 100 3/8 1.82 2.10 12.09 50 1/2 2.21 2.55 17.88 50 5/8 4.60 5.79 40.86 25 3/4 7.26 8.46 69.24 20 7/8 22.82 25.71 125.89 15 1 27.19 29.91 164.99 BULK 1-1/8 46.43 48.64 -- BULK 1-1/4 53.12 69.24 -- BULK 1-1/2 87.24 119.36 -- BULK FIG. 51R reducing rod coupling Electro-Galvanized (51RG) Designed for connecting two lengths of rod with different diameters. Specify figure number, finish and rod size. E.G. 3/8 X 1/4 9.25 100 1/2 X 3/8 9.71 100 5/8 X 1/2 11.58 100 3/4 X 5/8 16.52 100 7/8 X 3/4 37.18 50 1 X 7/8 51.48 50 v 04302018.1 empire industries, inc. 15
FIG. 52 round steel washer E.G. SS SX Plain Carbon Steel (52B) Electro-Galvanized (52G) T-304 Stainless (52SS) T-316 Stainless (52SX) Designed to produce a greater bearing surface. Specify figure number, finish and rod size. FULL CARTON QUANTITIES ONLY ON S 1/4-3/4. 1/4 0.17 0.23 -- 100 3/8 0.23 0.28 0.91 100 1/2 0.51 0.57 1.76 50 5/8 1.08 1.36 2.61 25 3/4 1.65 1.93 3.24 20 7/8 1.99 2.50 6.92 15 1 3.80 4.31 -- 25 1-1/8 4.31 4.99 -- 25 1-1/4 4.54 5.45 -- 50 1-1/2 6.47 7.89 -- 50 FIG. 52F fender washer Electro-Galvanized (52FG) Designed to produce a greater bearing surface. Specify figure number, finish and rod size. OUTSIDE DIAMETER E.G. 1/4 1-1/2 0.79 100 3/8 1-1/2 0.91 100 1/2 2 1.19 50 FIG. 53 angle bracket Plain Carbon Steel (53B) Hot-Dip Galvanized (53HDG) T-316 Stainless (53SX) Electro-Galvanized (53G) T-304 Stainless (53SS) Designed for attaching hanger rod to the side of beams or walls. Complies with Federal Specification WW-H-171-E (Type# 35), A-A-1192 A (Type# 34), and MSS SP-58 and 7SP-69 (Type# 34). Specify figure number, finish and rod size. FULL CARTON QUAN- TITIES ON 3/8 AND 1/2 (Plain and EG only). STAINLESS BULK ONLY 5/8-7/8. E.G. SS SX 3/8 3.46 3.92 1/2 4.26 5.51 100 5/8 16.18 21.68 20 3/4 18.28 24.35 20 7/8 20.38 25.88 20 100 16 empire industries, inc. v 04302018.1
FIG. 54 continuous threaded rod Plain Carbon Steel (54B) Electro-Galvanized (54G) T-304 Stainless (54SS) T-316 Stainless (54SX) Useful in applications for attaching hangers to structural attachments. Specify figure number, finish and rod size. Stainless steel rod is recommended for applications where protection from a corrosive environment is required. AVAIL- ABLE IN 6 AND 10 LENGTHS (Plain and EG only). FULL BUNDLE QUANTITIES ON 3/8-3/4. FIG. 55 hanger bolts (DIA x LENGTH) 1/4-20 x 6 1/4-20 x 10 3/8-16 x 6 3/8-16 x 10 1/2-13 x 6 1/2-13 x 10 5/8-11 x 6 5/8-11 x 10 3/4-10 x 6 3/4-10 x 10 7/8-9 x 6 7/8-9 x 10 1-8 x 6 1-8 x 10 1-1/8-7 x 6 1-1/8-7 x 10 1-1/4-7 x 6 1-1/4-7 x 10 1-1/2-6 x 6 1-1/2-6 x 10 E.G. SS SX BUNDLE QUANTITIES 6.47 10.84 9.54 15.84 16.86 28.15 28.72 47.90 41.89 69.81 83.15 138.60 117.49 195.81 155.91 259.89 186.79 311.31 289.18 481.98 8.74 14.59 11.07 18.50 21.11 35.19 33.88 56.47 53.75 89.56 103.30 172.20 136.73 227.88 182.70 304.50 229.98 383.28 353.14 58851 28.38 -- 59.88 -- 103.98 -- 176.40 -- 240.65 -- 382.71 -- 497.36 -- -- -- -- -- -- -- E.G. 50 25 15 9 6 -- -- -- -- -- Plain Carbon Steel (55B) Electro-Galvanized (55G) Designed for suspending pipe supports from wood structures. Specify figure number, finish and rod size. FULL BOX QUANTITIES ONLY. 1/4 x 3-1/2 2.04 2.50 100 3/8 x 3-1/2 1.93 3.29 50 3/8 x 4-1/2 2.38 3.80 50 3/8 x 6 2.67 4.54 25 3/8 x 8 3.29 5.16 25 3/8 x 10 4.54 6.47 25 3/8 x 12 5.22 7.09 25 1/2 x 4 4.09 6.81 25 1/2 x 6 4.71 7.32 25 1/2 x 8 9.93 11.58 25 5/8 x 4 9.88 14.08 25 v 04302018.1 empire industries, inc. 17
FIG. 56 / 56H standard hex nut / heavy hex nut, packaged FIG. 56 E.G. SS SX Plain Carbon Steel (56B) Electro-Galvanized (56G) T-304 Stainless (56SS) T-316 Stainless (56SX) Plain Carbon Steel (56HB) Electro-Galvanized (56HB) T-304 Stainless (56HSS) T-316 Stainless (56HSX) Fastener Specify figure number, finish and rod size. FULL BOX QUANTITIES ONLY 1/4 0.23 0.28 -- 3/8 0.28 0.34 0.96 100 1/2 0.57 0.68 1.87 50 5/8 1.19 1.70 3.01 25 3/4 1.82 2.44 4.88 20 7/8 2.72 3.35 7.32 15 1 4.54 4.94 -- 10 1-1/8 8.63 10.50 -- 10 1-1/4 9.76 11.92 -- 5 1-1/2 16.29 17.14 -- 10 FIG. 56H E.G. SS SX 100 1/4 0.34 0.28 100 3/8 0.40 0.34 100 1/2 0.96 0.68 50 5/8 1.65 1.70 25 3/4 3.06 2.44 20 7/8 4.77 3.35 15 1 7.66 4.94 10 1-1/8 13.22 10.50 10 1-1/4 13.28 11.92 5 1-1/2 24.86 17.14 10 FIG. 57 hanger rod Plain Carbon Steel (57B) Hot-Dip Galvanized (57HDG) T-316 Stainless (57SX) Electro-Galvanized (57G) T-304 Stainless (57SS) Double Right Hand Threads (56RR) Double Left Hand Threads(56LL) Left and Right Hand Threads (56RL) Designed for use in pipe hanger assemblies. Specify figure number, finish, thread direction, rod size, length and thread length. Threads are not chased on hot-dip galvanized rod. PRICED ON APPLICATION 18 empire industries, inc. v 04302018.1
FIG. 58 hex head bolt Plain Carbon Steel (58B) Electro-Galvanized (58G) T-304 Stainless (58SS) T-316 Stainless (58SX) Designed for use as a fastening device. Specify figure number, rod size and length. Other sizes available. Priced on application. E.G. SS SX DIAMETER LENGTH 1/2 1-1/2 1.19 1.36 1-3/4 1.25 1.42 50 2 1.59 1.70 50 2-1/2 1.82 1.95 50 2-3/4 2.72 -- 50 3 2.84 2.72 50 E.G. SS SX DIAMETER LENGTH 5/8 FIG. 60 1-1/2 2.27 2.44 2 2.44 2.61 25 2-1/4 2.72 2.89 25 2-1/2 2.84 3.18 25 2-3/4 3.92 4.14 25 3 4.03 4.20 25 3-1/4 4.14 4.37 25 3-1/2 4.31 4.54 25 3-3/4 4.48 4.77 25 4 5.28 5.56 25 4-1/2 6.47 25 1/4 beam clamp 5 5.51 7.61 25 50 25 E.G. SS SX DIAMETER LENGTH 2 4.37 5.34 20 2-1/4 4.54 5.90 20 2-1/2 5.16 6.19 20 2-3/4 5.51 6.58 20 3 5.62 6.70 20 3/4 3-1/4 5.73 6.87 20 3-1/2 5.90 7.09 20 3-3/4 6.81 7.44 20 4 7.61 7.61 20 4-1/2 8.23 8.85 30 5 8.46 9.42 30 6 10.61 11.69 30 E.G. SS SX DIAMETER LENGTH 3 8.91 9.76 15 3-1/4 9.25 10.50 15 7/8 3-1/2 9.99 11.46 15 4 10.78 16.80 15 4-1/2 11.52 19.41 15 5 13.62 23.89 15 E.G. SS SX DIAMETER LENGTH 3 11.69 14.70 10 3-1/2 12.60 -- 10 1 4 14.42 16.80 10 4-1/2 16.06 19.41 10 5 20.66 23.89 10 Electro-Galvanized Malleable Iron (60G) Designed to attach 1/4 hanger rod from metal beams, channel or angle iron. Specify figure number, finish and rod size. E.G. 1/4 3.18 100 v 04302018.1 empire industries, inc. 19
FIG. 61 wide mouth beam clamp 61D ONLY Plain Malleable Iron (61B) FIG. 62 Electro-Galvanized (61G) Plain Malleable Iron: Domestic, 3/8 & 1/2 (61DB) Electro-Galvanized: Domestic, 3/8 & 1/2 (61DG) Designed to attach hanger rod to the top or bottom flange of a beam or bar. U.L. - U.L.C. listed 3/8 and 1/2 (1/2 for 4 IPS max). FM approved for 3/8 only. Complies with Federal Specification A-A-1192A (Type# 19) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 19). Specify figure number, finish and rod size. See MSS SP-69 for proper set screw torque recommendations. small mouth beam clamp (61DB) E.G. E.G. (61DG) 3/8 4.99 9.48 5.96 11.01 100 1/2 6.24 10.78 8.34 15.78 100 5/8 11.46 -- 15.78 -- 50 3/4 14.98 -- 19.01 -- 50 Plain Malleable Iron: 3/8-7/8 (62B) Electro-Galvanized: 3/8-7/8 (62G) T-304 Stainless: 1/4-3/4 (62SS) T-316 Stainless: 1/4-3/4 (62SX) N/A Designed to attach hanger rod to the top or bottom flange of a beam or bar joist where flange thickness does not exceed 5/8 of an inch. U.L. - U.L.C. listed 3/8 and 1/2 (1/2 for 4 IPS max). FM approved for 3/8 only. Complies with Federal Specification A-A-1192 A (Type# 19) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 19). Specify figure number, finish and rod size. Set screw is of hardened steel. See MSS SP-69 for proper set screw recommendations. Stainless steel beam clamps are recommended for corrosive environments. E.G. SS SX 1/4 -- -- 47.96 55.45 100 3/8 3.12 3.86 47.96 55.45 100 1/2 3.86 4.71 54.94 63.79 100 5/8 9.02 12.94 -- 136.37 50 3/4 12.20 17.42 -- 156.88 50 7/8 14.08 19.64 -- -- 50 FIG. 63 electrical rod support clamp Electro-Galvanized Malleable Iron (63G) T-316 Stainless: 1/4, 3/8 and 1/2 (63SX) Designed to attach hanger rod to beam or framework where material thickness does not exceed 1/2 inch. Rod tap on both bottom and back of clamp. Specify figure number, finish and rod size E.G. SX 1/4 3.18 54.09 50 5/16 6.30 57.78 50 3/8 10.27 105.79 25 1/2 29.80 155.06 25 20 empire industries, inc. v 04302018.1
FIG. 66L/66W welding beam attachment with and without nut and bolt Plain Carbon Steel (66LB) Hot-Dip Galvanized (66LHDG) T-316 Stainless (66LSX) Electro-Galvanized (66LG) T-304 Stainless (66LSS) Plain Carbon Steel w/ bolt (66WB) Electro-Galvanized w/ bolt (66WG) Hot-Dip Galvanized w/ bolt (66WHDG) T-316 Stainless w/ bolt (66WSX) T-304 Stainless w/ bolt (66WSS) Designed for the attachment of hanger rod to the bottom flange of steel beams where heavy loads and large hanger rod sizes are required. Complies with Federal Specification WW-H-171-E (Type# 22), A-A- 1192A (Type# 22), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 22). Can be welded in either the upright or inverted position when ordered with hardware. 3/8 to 1-1/8 supplied with bolts and nuts. 1-1/4 and larger supplied with pins and cotters. FIG. 66L and 66W size 2 beam attachment will be welded rather than formed. FIG. 67 concrete clevis plate 66L 66W 3/8 14.70 22.59 1/2 14.70 22.59 5/8 15.32 25.14 3/4 23.21 38.37 7/8 31.78 48.47 1 71.68 107.47 1-1/8 93.08 147.85 1-1/4 176.40 263.01 1-1/2 303.08 446.28 E.G. H.D.G. SS SX ALL FINSHES 3/8 1/2 Plain Carbon Steel (67B) Hot-Dip Galvanized (67HDG) T-316 Stainless (67SX) Electro-Galvanized (67G) T-304 Stainless (67SS) Designed for the attachment to concrete ceilings where flexibility is desired. Normally used in conjunction with FIG. 13 weldless eye nut or FIG. #26W welded eye rod. Specify figure number, finish and rod size. 5/8 3/4 7/8 1 1-1/8 1-1/4 1-1/2 FIG. 68 concrete rod attachment ALL FINISHES 3/8 1/2 Plain Carbon Steel (68B) Hot-Dip Galvanized (68HDG) T-316 Stainless (68SX) Electro-Galvanized (68G) T-304 Stainless (68SS) Designed for the attachment of hanger rod to concrete ceilings where vertical adjustment of hanger is desired. Specify figure number, finish and rod size. 5/8 3/4 7/8 1 1-1/8 1-1/4 1-1/2 v 04302018.1 empire industries, inc. 21
FIG. 69L / 69S structural welding lug, long / short Plain Carbon Steel (69SB) Hot-Dip Galvanized (69SHDG) T-316 Stainless (69SSX) Electro-Galvanized (69SG) T-304 Stainless (69SSS) Plain Carbon Steel (69LB) Electro-Galvanized (69LG) Hot-Dip Galvanized (69LHDG) T-316 Stainless (69LSX) T-304 Stainless (69LSS) Designed to be welded to structural members and used in conjunction with figure #909 forged steel clevis with pin and cotters. Complies with Federal Specification WW-H-171-E (Type# 57), A-A- 1192A (Type# 57), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 57). Specify figure number, finish and rod size. Radiused edge available. PRICE EACH SHORT LONG PKG 1/2 BULK 5/8 BULK 3/4 BULK 7/8 BULK 1 BULK 1-1/4 BULK 1-1/2 BULK FIG. 72 bevel washer E.G. Plain Carbon Steel (72B) Electro-Galvanized (72G) Designed to compensate for taper of S shape beam flanges so that bearing surface of bolt or nut will seat flush. Specify figure number and bolt size. 3/8 7.09 1/2 7.32 5/8 7.61 3/4 7.89 7/8 12.54 22 empire industries, inc. v 04302018.1
FIG. 73 drop in anchor Electro-Galvanized (73G) T-316 Stainless (73SX) T-304 Stainless (73SS) Designed to be inserted into a pre-drilled hole and set by means of a setting tool to provide attachment point for bolts or hanger rods. Specify figure number, finish and bolt or rod size. FULL BOX QUAN- TITIES ONLY ON S 3/8 AND 1/2. SET TOOL IN BOX. E.G. SS SX PKG 3/8 1.14 1/2 2.72 50 5/8 9.76 25 3/4 21.62 10 50 FIG. 75 steel washer plate Plain Carbon Steel (75B) Electro-Galvanized (75G) T-304 Stainless (75SS) T-316 Stainless (75SX) Designed as a heavy duty washer to suspend hanger rods. Specify figure number, finish, thickness, length, width and rod size. Other dimensions and sizes available upon request. PRICES ARE FOR FINISH. OTHER FIN- ISHES AVAILABLE AND ARE PRICED ON APPLICATION. 2 x 2 x 1/4 3 x 3 x 1/4 4 x 4 x 1/4 4 x 4 x 3/8 PRICE/ PRICE/ PRICE/ PRICE/ 3/8 3.80 6.41 10.22 18.84 1/2 3.80 6.41 10.22 18.84 5/8 -- 6.53 10.22 18.84 3/4 -- 6.81 10.50 19.24 7/8 -- 7.26 10.78 19.58 1 -- 7.44 11.01 19.98 v 04302018.1 empire industries, inc. 23
FIG. 81 concrete insert Plain Carbon Steel (81B) Plain Carbon Steel Insert Nut (81NB) Electro-Galvanized Insert Nut (81NG) Electro-Galvanized (81G) Heavy gauge insert box is nailed to concrete form. When concrete has set, knock out plug can be removed and insert nut installed. Side openings accommodate up to 1/2 reinforcing rods. FM approved on sizes 3/8 and 1/2. Complies with Federal Specification WW- H-171-E (Type# 19), A-A-1192A (Type# 18), and Manufacturers Standardization Society MSS SP-58 (Type# 18) and SP-69 (Type# 18). Specify figure number and finish. For insert nuts, specify figure number, rod size and finish. INSERT BOX ONLY E.G. -- 7.83 10.10 45 NUT E.G. 1/4 1.87 2.44 100 3/8 1.87 2.44 100 1/2 2.04 2.78 100 5/8 2.78 3.41 100 3/4 3.06 3.80 100 FIG. 83/84 spring wing toggle with bolt / without bolt Electro-Galvanized (83G) Electro-Galvanized: Toggle only (84G) Designed to be used with threaded rod in hollow walls. Specify figure number and size. FULL BOX QUANTITIES ONLY. FIG. 83 SPRING WING TOGGLE AND BOLT E.G. 1/4 x 3 2.44 100 3/8 x 4 5.22 50 FIG. 84 SPRING WING TOGGLE HEAD ONLY E.G. 1/4 2.21 100 3/8 3.92 50 FIG. 95 offset pipe clamp Plain Carbon Steel (95B) Hot-Dip Galvanized (95HDG) T-316 Stainless (95SX) Electro-Galvanized (95G) T-304 Stainless (95SS) Designed for supporting horizontal or vertical pipe lines at a fixed distance from wall or floor. This clamp can be furnished with B dimensions to suit field conditions. Specify figure number, pipe type, finish and pipe size Custom B dimension available. Also availble in DIP/C900 (95DIP) and OD (95OD) sizes. E.G./H.D.G./ SS/SX 3/4 74.41 1 74.81 1-1/4 75.32 1-1/2 79.86 2 85.82 2-1/2 89.68 3 91.72 4 99.15 5 115.67 6 137.46 8 160.68 10 24 empire industries, inc. v 04302018.1
FIG. 97 extended pipe clamp Plain Carbon Steel (97B) Hot-Dip Galvanized (97HDG) T-316 Stainless (97SX) Electro-Galvanized (97G) T-304 Stainless (97SS) Designed for suspending or supporting pipe lines where exact distance between structure and pipe cannot be determined until installation. Specify figure number, finish and pipe size Custom B dimension available. Also available in Ductile Iron Pipe (97DIP) and OD (97OD)sizes. FIG. 110 adjustable clevis hanger, light weight E.G./H.D.G/ SS/SX 3/4 79.57 1 82.30 1-1/4 85.08 1-1/2 94.50 2 97.68 2-1/2 104.26 3 106.48 4 118.45 5 135.02 6 150.86 8 194.28 10 E.G. P.C. GI Plain Carbon Steel (110B) Plastic Coated (110PC) Electro-Galvanized, Imported: (110GI) Electro-Galvanized (110G) Designed for the suspension of non insulated, stationary pipe lines. Complies with Federal Specification WW-H-171-E (Type# 12) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 1). Galvanized only. Specify figure number, material, finish type and pipe size. Upper locknut must be tightened securely to assure proper hanger performance. Conduit comes in various outside diameters. Verify outside diameter of conduit is equal to outside diameter of schedule 40 steel pipe. FIG. 110CT excluding: 110GI clevis hanger for copper tubing 3/8 2.16 2.55 10.33 -- 100 1/2 2.16 2.55 10.50 2.10 100 3/4 2.16 2.55 10.56 2.16 100 1 2.21 2.61 11.01 2.33 100 1-1/4 2.38 2.84 11.64 2.50 100 1-1/2 2.61 3.18 12.71 2.61 100 2 2.84 3.58 14.36 2.89 100 2-1/2 5.45 7.04 22.02 5.45 50 3 6.13 8.40 27.41 6.81 25 3-1/2 7.21 9.48 40.98 -- 25 4 7.26 9.71 27.87 8.68 25 5 -- -- 42.85 -- 25 6 -- -- 67.48 -- 10 7 -- -- 105.00 -- 10 8 -- -- 107.84 -- 10 10 -- -- 169.08 -- BULK 12 -- -- 225.10 -- BULK Copper Plated Carbon Steel (110CT) Copper Epoxy Coated Copper-Gard, Imported: (110CTI) Designed for the suspension of stationary copper tubing. Complies with Federal Specifications WW-H-171-E (Type# 1), A-A-1192 A (Type# 1), and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 1). Specify figure number and tube size excluding: 110CTI COPPER-GARD products offer superior corrosion protection due to the epoxy coating over electro-galvanized steel. The alternative copper plating, that has been done historically, identifies the product and is not intended for protection. Refer to MSS SP-58, 13.3. TUBE COPPER PLATED COPPER EPOXY COATED 1/2 3.12 2.38 100 3/4 3.18 2.44 100 1 3.35 2.55 100 1-1/4 3.69 2.95 100 1-1/2 3.80 3.06 100 2 4.54 3.63 100 2-1/2 9.99 8.63 50 3 10.22 9.42 50 3-1/2 11.18 12.37 25 4 12.94 12.32 25 5 26.90 25.48 25 6 31.16 29.97 10 v 04302018.1 empire industries, inc. 25
FIG. 114 turnbuckle adjuster Plain Malleable Iron (114B) Designed to provide vertical rod adjustment. Electro-Galvanized (114G) Complies with Federal Specification WW-H-171-E (Type# 15), A-A-1192 A (Type# 15) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 15). Specify figure number and rod size. E.G. WGT EACH (LBS) 3/8 8.91 100 0.516 1/2 11.29 50 0.545 FIG. 126 one hole clamp Electro-Galvanized Malleable Iron (126G) Designed for the support of conduit, cable or pipe on walls or sides of beams. Not recommended for horizontal use on ceilings or bottom of beams. Specify figure number and pipe size. E.G. WGT EACH (LBS) 1/2 1.08 100 0.04 3/4 1.31 100 0.05 1 1.70 100 0.09 1-1/4 2.27 100 0.12 1-1/2 2.67 100 0.16 2 4.82 50 0.25 2-1/2 8.74 50 0.49 3 12.77 25 0.82 4 29.12 10 1.30 FIG. 127CT / 127CTP natick hanger, copper tube size Copper Epoxy Coated (Copper-Gard) Carbon Steel (127CT) Copper Plated Carbon Steel (127CTP) Designed for the support of copper tube supply lines. Attaches to wood members. Specify figure number, finish, tube size and length. FULL CARTONS ONLY. 26 empire industries, inc. v 04302018.1 TUBE EPOXY COATED COPPER PLATED WGT EACH (LBS) 1/2 X 6 2.27 2.27 25 0.075 3/4 X 6 2.33 2.33 25 0.075 1 X 6 2.38 2.38 25 0.090 1-1/4 X 6 2.67 2.67 25 0.095 1-1/2 X 6 2.78 2.78 25 0.110 2 X 6 3.01 3.01 25 0.125 1/2 X 12 2.72 2.72 25 0.130 3/4 X 12 2.84 2.84 25 0.130 1 X 12 2.95 2.95 25 0.140 1-1/4 X 12 3.24 3.24 25 0.150 1-1/2 X 12 3.35 3.35 25 0.160 2 X 12 3.58 3.58 25 0.170
FIG. 129CT / 129CTP van (bell type) hanger for copper tube Copper Epoxy Coated (Copper-Gard) Carbon Steel (129CT) Copper Plated Carbon Steel (129CTP) Solid Brass (129CTSB) Designed to support copper tubing to wall. Supports the pipe 1 from the back of pipe to wall. The wood screw is concealed upon installation. Specify figure number, finish and tube size. FULL CAR- TONS ONLY. TUBE EPOXY COATED COPPER PLATED SOLID BRASS WGT EACH (LBS) 1/2 2.04 2.04 9.02 25 0.070 3/4 2.16 2.16 9.42 25 0.075 1 2.27 2.27 9.76 25 0.075 1-1/4 2.89 2.89 -- 25 0.080 1-1/2 3.58 3.58 -- 25 0.100 2 5.79 5.79 -- 25 0.115 FIG. 131CT / 131CTP milford hanger for copper tube Copper Epoxy Coated (Copper-Gard) Carbon Steel (131CT) Copper Plated Carbon Steel (131CTP) Designed for the support of copper tube supply lines. Attaches to wood members. Specify figure number, finish, tube size and length. FULL CARTONS ONLY. TUBE EPOXY COATED COPPER PLATED WGT EACH (LBS) 1/2 X 6 2.27 2.27 25 0.085 3/4 X 6 2.38 2.38 25 0.090 1 X 6 2.44 2.44 25 0.090 1-1/4 X 6 3.86 3.86 25 0.095 1-1/2 X 6 3.97 3.97 25 0.100 2 X 6 4.26 4.26 25 0.125 1/2 X 12 3.24 3.24 25 0.130 3/4 X 12 3.35 3.35 25 0.130 1 X 12 3.46 3.46 25 0.135 1-1/4 X 12 4.82 4.82 25 0.140 1-1/2 X 12 5.34 5.34 25 0.145 2 X 12 5.85 5.85 25 0.175 FIG. 136 right angle clamp Electro-Galvanized Malleable Iron (136G) T-316 Stainless Steel (136SX) Designed for anchoring pipe or conduit at a right angle to structural members. Specify figure number, pipe size and finish. E.G. SX WGT EACH (LBS) 1/2 9.19 59.59 50 0.40 3/4 9.36 64.99 50 0.42 1 11.98 66.18 50 0.48 1-1/4 12.37 83.21 50 0.55 1-1/2 13.68 96.71 50 0.57 2 18.73 125.26 50 0.89 2-1/2 20.38 150.12 25 1.10 3 21.91 173.90 25 1.14 3-1/2 27.30 25 1.30 4 28.95 199.95 25 1.40 v 04302018.1 empire industries, inc. 27
FIG. 137 standard ips / dip sized u-bolt with 4 hex nuts E.G. H.D.G. SS SX STD PKG Plain Carbon Steel (137B) Hot-Dip Galvanized (137HDG) Electro-Galvanized (137G) Plastic Coated (137PC) T-304 Stainless Steel (137SS) T-316 Stainless Steel (137SX) Plain Carbon Steel for DIP (137DIPB) T-304 Stainless Steel for DIP (137DIPSS) Hot-Dip Galvanized for DIP (137DIPHDG) T-316 Stainless Steel for DIP (137DIPSX) Pipe Gard (137PG), Pipe Gard for DIP (137DIPPG) - Please contact factory for details. Designed for support or guide of heavy loads. Complies with Federal Specifications WW-H-171-E (Type# 24), A-A-1192 A (Type# 24), and MSS SP-58 and SP-69 (Type# 24). Specify figure number, finish and pipe size. Available in DIP sizes and special dimensions - Priced on application. Contact factory for details. 1/2 1/4 1.32 1.41 2.29 12.60 100 3/4 1/4 1.38 1.45 2.42 12.88 100 1 1/4 1.42 1.49 2.60 13.11 100 1-1/4 3/8 3.29 4.03 5.00 19.64 100 1-1/2 3/8 3.69 4.20 5.28 20.60 100 2 3/8 3.92 4.48 5.69 22.87 100 2-1/2 1/2 7.15 7.55 9.92 41.77 50 3 1/2 7.55 8.74 11.20 42.06 50 3-1/2 1/2 8.00 9.42 -- -- 50 4 1/2 8.29 9.54 12.35 48.19 50 5 1/2 8.97 11.86 15.53 79.46 25 6 5/8 17.31 20.94 27.80 102.33 25 8 5/8 19.998 24.06 33.63 128.21 10 10 3/4 36.84 41.66 54.57 212.10 10 12 7/8 60.05 65.61 91.57 332.82 10 14 7/8 66.97 86.04 -- -- BULK 16 7/8 79.40 107.33 -- -- BULK 18 1 119.36 158.58 -- -- BULK 20 1 161.25 201.20 -- -- BULK 24 1 174.30 248.31 -- -- BULK FIG. 146 offset j-hook ALL FINISHES 3/4 1 1-1/4 Plain Carbon Steel (146B) Electro-Galvanized (146G) T-304 Stainless Steel (146SS) T-316 Stainless Steel (146SX) Designed for supporting light pipe loads with 1 offset from wall to provide clearance for fittings. Specify figure number, finish and pipe size. 100 PC MINIMUM ORDER. 1-1/2 2 2-1/2 3 4 5 6 28 empire industries, inc. v 04302018.1
FIG. 150 beam clamp Hot-Dip Galvanized (150HDG) T-316 Stainless Steel (150SX) T-304 Stainless Steel (150SS) Designed for attaching hanger rods from the center of an I-beam. Normally used with figure 13 weldless eye nut. Complies with Federal Specifications WW-H-171-E (Type# 21), A-A-1192 A (Type# 21), and MSS SP-58 and SP-69 (Type# 21). Specify figure number, finish, clamp size, flange width, beam thickness. Not available for beams greater that 8 wide. PRICED ON AP- PLICATION. CLAMP 1 2 ALL FINSHES FIG. 152 return line angle Plain Carbon Steel (152B) Electro-Galvanized (152G) Designed to enable the field mechanic to obtain different distances from wall to center of pipe line by turning the angle to distance required. They are made in light and heavy material and will support pipes 2, 3 or 4 inches from wall to center of pipe. Complies with Federal Specifications WW-H-171-E (Type# 21), A-A-1192 A (Type# 21), and MSS SP-58 and SP-69 (Type# 21). Specify figure number, finish and size number. FIG. 153 side beam connector E.G. 1 10.90 12.88 2 11.41 13.17 3 19.69 4 20.15 5 20.38 6 22.53 Plain Carbon Steel (153B) Electro-Galvanized (153G) Designed for mounting to sides of wood beams. Bottom hole is tapped for rod. Specify figure number, finish and rod size. E.G. STD PKG 3/8 1.93 3.29 100 1/2 4.43 6.13 100 v 04302018.1 empire industries, inc. 29
FIG. 155 steel beam clamp Electro-Galvanized (155G) Designed for attaching hanger rods to be centered under beam flanges. The clamp provides a vertical adjustment of approximatly 2 inches. Specify figure number, finish, clamp size, beam thickness and flange width. Not available for beams greater than 8 inches wide. CLAMP 2 1/2 3 5/8 4 3/4 5 7/8 E.G. FIG. 156 steel beam clamp Plain Carbon Steel (156B) Electro-Galvanized (156G) T-304 Stainless Steel (156SS) T-316 Stainless Steel (156SX) Designed to be used where it is necessary for the hanger rod to run vertically close to the beam s edge, eliminating drilling of holes in structural member. Complies with Federal Specifications WW-H-171-E (Type# 53), A-A-1192 A (Type# 25), and MSS SP-58 and SP-69 (Type# 25). Specify figure number, finish, clamp size, beam thickness and flange width. Not available for beams greater than 8 inches wide. FIG. 157 extension piece NO. 1 3/8 2 1/2 3 5/8 4 3/4 5 7/8 ALL FINISHES E.G. Plain Carbon Steel (157B) Electro-Galvanized (157G) Designed for attaching hanger rod to various type of attachments. Allows a 1 inch vertical adjustment of the rod. Specify figure number, finish and rod size. 3/8 5.28 6.30 1/2 9.02 10.78 5/8 10.61 12.66 3/4 17.76 20.89 7/8 21.68 27.92 30 empire industries, inc. v 04302018.1
FIG. 158 top beam hook Plain Carbon Steel (158B) Electro-Galvanized (158G) Designed for attaching hanger rod to the top flange of a beam. Specify figure number, finish, hook size, beam thickness and flange width. Not available for beams greater than 8 inches wide. NO. 1 3/8 2 1/2 3 5/8 4 3/4 5 7/8 ALL FINISHES FIG. 159 adjustable rod beam clamp Plain Carbon Steel (159B) Electro-Galvanized (159G) Designed to be used in the suspension of a hanger rod from an I-beam. Recommended for flange widths from 4 inches minimum to 8 inches maximum. Complies with Federal Specifications WW-H-171-E (Type# 54), A-A-1192 A (Type# 27), and MSS SP-58 and SP-69 (Type# 27). Specify figure number, finish and rod size. E.G. 3/8 19.47 25.31 25 1/2 25.71 33.43 25 5/8 31.84 41.49 25 FIG. 167 pipe covering protection shield SHIELD ID PRICE / MILL HDG SHIELD ID PRICE / MILL HDG Pre-Galvanized (167G) T-316 Stainless Steel (167SX) T-304 Stainless Steel (167SS) Designed for outside of foam or fiberglass insulation on stationary pipe lines (not designed for pipe rollers) to prevent crushing of insulation without breaking the vapor barrier. Specify figure number and shield size. STAINLESS SHIELDS PRICED ON APPLICATION. 0 1-7/8 6.07 1 2-3/8 6019 2 2-7/8 6.98 3 3-1/2 10.78 4 4 12.32 5 4-1/2 12.88 6 5 14.70 7 5-5/8 16.80 8 6-5/8 18.62 9 7-5/8 23.10 10 8-5/8 25.20 13 9-5/8 33.49 14 10-3/4 37.52 15 11-3/4 42.34 16 12-3/4 45.63 17 14 59.08 18 15 66.18 19 16 84.91 20 17 92.46 21 18 121.69 22 19 134.80 23 20 138.77 24 21 148.42 25 22 160.79 26 23 166.30 27 24 172.65 28 26 179.75 29 27 191.61 30 28 204.10 v 04302018.1 empire industries, inc. 31
FIG. 167MSS mss pipe covering protection shield SHIELD ID PRICE / MILL HDG SHIELD ID PRICE / MILL HDG Pre-Galvanized (167MSSG) T-316 Stainless Steel (167MSSSX) T-304 Stainless Steel (167MSSSS) Designed for outside of foam or fiberglass insulation on stationary pipe lines (not designed for pipe rollers) to prevent crushing of insulation without breaking the vapor barrier. Specify figure number and shield size. STAINLESS SHIELDS PRICED ON APPLICATION. FIG. 168 short pipe covering protection shield X1A 1-7/8 11.58 1A 2-3/8 11.81 2A 2-7/8 12.32 3A 3-1/2 13.05 4A 4 14.19 5A 4-1/2 15.10 6A 5 17.54 7A 5-5/8 19.07 8A 6-5/8 27.92 9A 7-5/8 32.01 10A 8-5/8 36.61 9B 7-5/8 48.30 10B 8-5/8 51.36 11B 9-5/8 61.18 12B 10-3/4 68.79 13C 11-3/4 130.71 14C 12-3/4 141.61 15C 14 151.60 16C 15 158.24 17C 16 172.43 18C 17 181.00 19C 18 261.65 20C 19 295.59 21C 20 330.84 22C 21 343.89 23C 22 362.16 24C 23 385.55 25C 24 437.48 26C 26 522.16 27C 27 533.80 28C 28 557.01 SHIELD ID PRICE / MILL HDG Pre-Galvanized (168G) T-316 Stainless Steel (168SX) T-304 Stainless Steel (168SS) Designed for outside of foam or fiberglass insulation on stationary pipe lines (not designed for pipe rollers) to prevent crushing of insulation without breaking the vapor barrier. Specify figure number and shield size. STAINLESS SHIELDS PRICED ON APPLICATION. MINIMUM ORDER OF 100 PCS. 0 1-7/8 6.64 1 2-3/8 7.21 2 2-7/8 8.40 3 3-1/2 9.99 4 4 11.35 5 4-1/2 12.09 6 5 14.02 7 5-5/8 15.21 8 6-5/8 17.31 FIG. 180 short clip Plain Carbon Steel (180B) Hot-Dip Galvanized (180HDG) T-316 Stainless Steel (180SX) Electro-Galvanized (180G) Designed to support pipe close to ceiling or wall. T-304 Stainless Steel (180SS) Complies with Manufacturers Standardization Society MSS SP- 58 & SP-69 (Type# 26) Specify figure number, finish and pipe size. E.G., H.D.G. AND STAINLESS PRICED ON APPLICATION. Sizes 1/2 to 2 are furnished with two screw holes. Sizes 21/2 to 4 are furnished with four screw holes. * Radius edge 1/2 to 2 with 2 holes. * Square edge 21/2 to 4 with four holes 1/2 12.09 3/4 12.20 1 12.26 1-1/4 13.68 1-1/2 15.49 2 19.86 2-1/2 51.25 3 23.29 3-1/2 46.54 4 52.50 E.G./ H.D.G./SS/ SX 32 empire industries, inc. v 04302018.1
FIG. 189 double bolt pipe clamp Plain Carbon Steel (189B) Hot-Dip Galvanized (189HDG) Electro-Galvanized (189G) T-304 Stainless Steel (189SS) T-316 Stainless Steel (189SX) Alloy Steel: ASTM A387 Grade 22 (189A) Designed for the suspension of insulated pipe lines. Normally used with weldless eye nut, figure #13. Complies with Federal Specifications WW-H-171-E (Type# 3), A-A-1192 A (Type# 3), and MSS SP-58 and SP-69 (Type# 3). Specify figure number, finish and pipe size. FIG. 189H heavy double bolt pipe clamp EG H.D.G./A/ SS/SX 1/2 24.69 31.84 3/4 24.80 32.07 1 24.92 32.29 1-1/4 27.47 34.11 1-1/2 30.14 36.84 2 31.16 37.91 2-1/2 34.68 41.55 3 35.25 42.28 3-1/2 55.85 83.43 4 104.09 153.30 5 133.55 189.96 6 164.94 258.30 8 183.44 299.34 10 264.60 460.52 12 307.96 474.71 14 529.54 932.57 16 633.18 990.12 18 713.04 1.127.70 20 921.05 1,473.69 24 1,345.08 1,934.21 ALL FINSHES Plain Carbon Steel (189HB) Hot-Dip Galvanized (189HHDG) T-316 Stainless Steel (189HSX) Electro-Galvanized (189HG) T-304 Stainless Steel (189HSS) Designed for suspension of high temperature pipe lines within the limitation of temperature and loads shown below. Complies with Federal Specifications WW-H-171-E (Type# 3), A-A- 1192 A (Type# 3), and MSS SP-58 and SP-69 (Type# 3). Specify figure number, finish and pipe size. Maximum temperature is 750 F and accommodates up to 4 thick insulation FIG. 200 bathtub wedge 6 8 10 12 14 16 18 20 24 30 36 Plain Malleable Iron (200B) Used for leveling and shimming tubs during and after installation. Specify figure number. 9.99 BULK v 04302018.1 empire industries, inc. 33
FIG. 202 side beam bracket Plain Carbon Steel (202B) Electro-Galvanized (202G) Designed for attaching hanger rod to the side of steel or wooden beams. Complies with Federal Specifications WW-H-171-E (Type# 35), A-A-1192 A (Type# 35), and MSS SP-58 and SP-69 (Type# 35). Specify figure number, finish and rod size. FIG. 212 standard steel pipe clamp E.G. STD PKG 3/8 4.20 100 1/2 7.38 50 Plain Carbon Steel (212B) Hot-Dip Galvanized (212HDG) T-316 Stainless Steel (212SX) Electro-Galvanized (212G) T-304 Stainless Steel (212SS) Designed for the suspension of cold pipe lines or hot pipe lines where no insulation is required. Complies with Federal Specifications WW-H-171-E (Type# 4), A-A-1192 A (Type# 4), and MSS SP-58 and SP-69 (Type# 4). Specify figure number, finish and pipe size. Normally used with Fig. 13 weldless eye nut, Fig 26 eyerod or Fig. 26W welded eyerod. FIG. 216 heavy duty two-bolt pipe clamp E.G. H.D.G./ SS/SX 1/2 9.88 13.17 3/4 10.05 13.22 1 10.22 13.39 1-1/4 10.39 13.74 1-1/2 10.95 14.81 2 11.07 16.06 2-1/2 11.58 17.14 3 12.15 17.88 3-1/2 13.51 20.77 4 17.65 25.48 5 24.35 33.43 6 49.28 65.78 8 59.42 82.13 10 105.79 156.71 12 120.32 171.29 14 192.50 345.00 16 218.75 349.65 18 358.75 551.25 20 498.75 673.75 24 612.50 857.50 Plain Carbon Steel (216B) Hot-Dip Galvanized (216HDG) T-316 Stainless Steel (216SX) Electro-Galvanized (216G) T-304 Stainless Steel (216SS) Designed for the suspension of cold or hot pipe lines with heavy loads where no insulation is required. Complies with Federal Specifications WW-H-171-E (Type# 4), A-A-1192 A (Type# 4), and MSS SP-58 and SP-69 (Type# 4). Specify figure number, finish and pipe size. 3 4 5 6 8 10 12 14 16 18 20 24 ALL FINISHES 34 empire industries, inc. v 04302018.1
FIG. 218 malleable iron center load beam clamp Plain Malleable Iron (218B) Electro-Galvanized (218G) Designed for the suspension of a hanger rod from the center of an I-beam. The clamp accommodates flange widths of 2-3/8-7. Flange thickness not to exceed.60 inches. Normally used in conjunction with figure 157 extension piece. Figure 157 provides 1 of vertical adjustment. When used with FIG. 157 Extension Piece, complies with Federal Specification WW-H-171-E (Type# 30), A-A-1192 A (Type# 30) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 30). Specify figure number and finish. For complete assembly with extension piece see FIG. 229. FIG. 229 FLANGE malleable beam clamp with extension piece E.G. STD PKG 3-7 37.80 50.29 20 Plain Carbon Steel (229B) Electro-Galvanized (229G) Designed for the suspension of a hanger rod from the center of an I-beam. The clamp accomodates flange widths of 2-3/8 to 7. Flange thickness not to exceed.60 inches. Extension piece provides 1 of vertical adjustment. Complies with Federal Specification WW-H-171-E (Type# 30), A-A-1192 A (Type# 30) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 30). Specify figure number and finish. FIG. 231 two hole pipe strap E.G. 3/8 43.14 56.59 1/2 16.88 61.01 5/8 48.41 62.77 3/4 55.05 71.14 7/8 59.48 78.23 E.G. SS (IPS) SS (OD) Electro-Galvanized (231G) T-316 Stainless Steel (231SX) T-304 Stainless Steel (231SS) T-304 Stainless Steel for OD Sizes: Domestic (231ODSS) T-316 Stainless Steel for OD Sizes: Domestic (231ODSX) Designed as a light duty support for schedule 40/80 sized pipe. Attaches directly to horizontal or vertical structural member. Complies with Manufacturers Standardization Society MSS SP-58 & SP-69 (Type# 26). Specify figure number finish and pipe or OD size. Stainless steel hangers are recommened for applications where protection from a corrsive environment is required. 1/4 0.34 7.55 7.55 100 3/8 0.34 7.61 7.61 100 1/2 0.40 7.72 7.72 100 3/4 0.51 7.83 7.83 100 1 0.79 8.00 8.00 100 1-1/4 0.96 10.10 100 1-1/2 1.19 10.67 100 2 1.76 11.58 100 2-1/2 3.06 14.42 50 3 3.75 16.80 50 4 4.99 23.10 50 6 17.08 64.08 25 v 04302018.1 empire industries, inc. 35
FIG. 231CT two hole strap for copper tubing FIG. 233 one hole pipe strap Copper-Gard (231CT) Designed as a light duty support for copper tubing. Attaches directly to horizontal or vertical structural member. Complies with Manufacturers Standardization Society MSS SP-58 & SP-69 (Type# 26) Specify figure number and tube size Available domestic TUBE COPPER GARD 1/4 0.34 100 3/8 0.34 100 1/2 0.40 100 3/4 0.45 100 1 0.57 100 1-1/4 0.68 100 1-1/2 1.42 100 2 1.76 100 Electro-Galvanized (233G) T-316 Stainless Steel (233SX) T-304 Stainless Steel (233SS) T-304 Stainless Steel for OD Sizes: (233ODSS) T-316 Stainless Steel for OD Sizes: (233ODSX) Designed as a light duty support for schedule 40/80 sized pipe. Attaches directly to horizontal structural member. Specify figure number finish and pipe or OD size FIG. 235/235CT wire pipe hook Stainless steel hangers are recommened for applications where protection from a corrsive environment is required. E.G. SS (IPS) SS (OD) 1/4 0.85 6.02 6.02 100 3/8 1.08 6.02 6.02 100 1/2 1.25 6.19 6.19 100 3/4 1.82 6.41 6.41 100 1 3.35 7.44 7.44 100 1-1/4 4.20 11.29 11.29 100 1-1/2 5.51 12.09 12.09 100 2 7.38 13.62 13.62 100 PKG P.C. (IPS) P.C. (CTS) Plain Carbon Steel (235B) Plastic Coated (235PC) Plastic Coated for Copper Tubing (235CT) Designed to support steel pipe horizontally by driving nail points into wood members. Specify figure number, finish and pipe size. BOX QUANTITY ONLY. 1/2 x 4 0.79 50 -- 0.91 -- 1/2 x 6 0.91 50 1.99 1.08 50 1/2 x 8 1.08 50 -- 1.31 -- 1/2 x 10 1.99 50 -- 2.44 -- 1/2 x 12 2.21 50 -- 2.78 -- 3/4 x 4 0.79 50 -- 0.91 -- 3/4 x 6 0.91 50 2.04 1.08 50 3/4 x 8 1.08 50 -- 1.31 -- 3/4 x 10 1.99 50 -- 2.44 -- 3/4 x 12 2.21 50 -- 2.78 -- 1 x 4 0.79 50 -- 0.91 -- 1 x 6 0.91 50 -- 1.08 50 1 x 8 1.08 50 -- 1.31 -- 1 x 10 1.99 50 -- 2.44 -- 1 x 12 2.21 50 -- 2.78 -- 1-1/4 x 6 1.48 50 -- 1.08 50 1-1/4 x 8 1.76 50 -- 1.31 -- 1-1/4 x 10 1.99 50 -- 2.44 -- 1-1/4 x 12 2.21 50 -- 2.78 -- 1-1/2 x 6 1.48 50 -- 1.70 -- 1-1/2 x 8 1.76 50 -- 1.87 -- 1-1/2 x 10 1.99 50 -- 2.44 -- 1-1/2x 12 2.21 50 -- 2.78 -- 2 x 6 1.48 50 -- 1.70 -- 2 x 8 1.76 50 -- 1.87 -- 2 x 10 1.99 50 -- 2.44 -- 2 x 12 2.04 50 -- 2.78 -- 36 empire industries, inc. v 04302018.1
FIG. 237 dwv (drain, waste, vent) hanger Pre-Galvanized (237G) Plastic Coated (237PC) Designed for the support of PVC or ABS DWV pipe from wood joists. Evenly spaced holes allow for proper pipe pitch. Specify figure number, finish and pipe size. BOX QUANTITY ONLY. excluding: 237PC PRE-GALV P.C. 1-1/2 2.72 4.94 25 2 3.01 5.28 25 3 3.29 5.73 25 4 4.54 6.64 25 FIG. 237CT dwv (drain, waste, vent) hanger for copper tubing Copper Plated Carbon Steel (237CT) Designed for the support of PVC or ABS DWV pipe from wood joists. Evenly spaced holes allow for proper pipe pitch. Specify figure number, finish and pipe size. FIG. 237CT copper plated DWV hangers are NOT designed for copper DWV pipe. BOX QUANTITY ONLY. PLATED 1-1/2 5.34 25 2 5.68 25 3 5.96 25 4 6.87 25 FIG. 239 perforated hanger strapping Plain Carbon Steel (239B) Copper Plated (239CT) Electro-Galvanized (239G) T-304 Stainless Steel (239SS) Electro-Galvanized w/ Alternating Hole (239AHG) Designed for various light duty applications. Specify figure number, finish, guage and length Stainless steel hangers are recommended for applications where protection from a corrosive environmemt is required. E.G. COPPER PLATED SS E.G. W/ ALT HOLE 3/4 x 24ga x 10 4.48 4.71 10.61 -- -- 3/4 x 22ga x 10 -- -- -- 50.74 5.51 3/4 x 20ga x 10 5.68 5.90 -- -- -- 3/4 x 24ga x 50 24.69 26.34 56.65 -- -- 3/4 x 22ga x 50 -- -- 253.59 31.27 3/4 x 20ga x 50 30.02 33.09 -- -- -- 3/4 x 24ga x 100 48.92 49.61 110.46 -- -- 3/4 x 22ga x 100 -- -- -- -- 59.99 3/4 x 20ga x 100 59.88 63.51 -- -- -- v 04302018.1 empire industries, inc. 37
FIG. 240 / 245 stud guard, triangle point / twist point Electro-Galvanized Carbon Steel: Triangle Point (240G) Electro-Galvanized Carbon Steel: Twist Point (245G) Designed to protect piping and electrical lines that pass though wood framing from damage due to penetration from drywall or other fasteners. Simple installation with a hammer.. Specify size & figure number. BOX QUANTITY ONLY. FIG. 241 / 243 nail plates non-fha / fha 240G 245G 16ga x 3 x 1-1/2 0.57 -- 100 16ga x 5 x 1-1/2 0.91 -- 100 16ga x 6 x 1-1/2 1.08 -- 100 18ga x 3 x 1-1/2 0.51 -- 100 18ga x 5 x 1-1/2 0.74 -- 100 18ga x 6 x 1-1/2 0.91 -- 100 19ga x 3 x 1-1/2 -- 0.51 100 19ga x 6 x 1-1/2 -- 0.79 100 (NON-FHA) Electro-Galvanized Carbon Steel (241G) (FHA) Electro-Galvanized Carbon Steel (243G) Designed to protect piping and electrical lines that pass though wood framing from damage due to penetration from drywall or other fasteners. Attach with metal framing screws. Specify figure number, gauge and size. BOX QUANTITY ONLY. FIG. 242G / 242GSN boca safety plate, regular / self nailing 241G 243G 18ga x 1-1/2 x 3 0.51 -- 250 18ga x 1-1/2 x 6 0.91 -- 100 18ga x 1-1/2 x 9 -- 1.48 50 18ga x 1-1/2 x 12 -- 1.70 50 18ga x 1-1/2 x 18 -- 2.84 50 18ga x 1-1/2 x 24 -- 3.69 50 18ga x 3 x 6 -- 1.76 50 18ga x 3 x 9 -- 2.78 50 18ga x 3 x 12 -- 3.80 50 18ga x 3 x 18 -- 5.62 50 16ga x 1-1/2 x 9 -- 1.82 50 16ga x 1-1/2 x 12 -- 2.44 50 16ga x 1-1/2 x 18 -- 3.69 50 16ga x 1-1/2 x 24 -- 5.28 50 16ga x 3-1/2 x 5 -- 2.21 50 16ga x 5 x 18 -- 11.07 25 13ga x 1-1/2 x 9 -- 3.35 50 13ga x 1-1/2 x 12 -- 4.82 25 13ga x 1-1/2 x 18 -- 6.81 25 13ga x 1-1/2 x 24 -- 8.91 25 Electro-Galvanized Carbon Steel: Regular (242G) Electro-Galvanized Carbon Steel: Self Nailing (245GSN) Designed to protect piping and electrical lines that pass though wood framing from damage due to penetration from drywall or other fasteners. Attach with metal framing screws. Specify size & figure number. BOX QUANTITY ONLY. 242G 242GSN 16ga x 5 x 8 3.92 -- 50 16ga x 5 x 8 -- 4.26 25 16ga x 5 x 4 -- 2.38 25 38 empire industries, inc. v 04302018.1
FIG. 255 pipe alignment guide (single spider clamp) H.D.G/ SS/SX 2 317.55 3 370.45 4 497.47 Plain Carbon Steel (255B) Hot-Dip Galvanized (255HDG) T-304 Stainless Steel (255SS) T-316 Stainless Steel (255SX) Designed for use with insulated or non-insulated pipe lines to maintain alignment of piping through axial expansion and contraction cycles. Proper alignment of the adjoining pipe is of vital importance in the proper functioning of expansion joints in the line. Pipe guides are not designed to support any piping system weight. Therefore additional supports are required. The use of two or more guides on both sides of the expansion joint is recommended to aviod a pivoting effect in the line. Maximum temperature: 650 F. Specify figure number, finish, size number and insulation thickness. 5 592.77 6 762.07 7 1,016.12 8 1,153.75 9 1,405.30 10 11 12 13 14 FIG. 256 pipe alignment guide H.D.G/ SS/SX 2 415.63 3 426.58 Plain Carbon Steel (256B) Hot-Dip Galvanized (256HDG) T-316 Stainless Steel (256SX) Electro-Galvanized (256G) T-304 Stainless Steel (256SS) Designed for use with insulated or non-insulated pipe lines to maintain alignment of piping through axial expansion and contraction cycles. Proper alignment of the adjoining pipe is of vital importance in the proper functioning of expansion joints in the line. Pipe guides are not designed to support any piping system weight, therefore additional supports are required. The use of two or more guides on both sides of the expansion joint is recommended to avoid a pivoting effect in the line. Maximum temperature is 750 F. Specify figure number, finish, size number and insulation thickness. 4 579.66 5 743.74 6 1,071.85 7 1,137.52 8 1,367.16 9 1,673.42 10 1,957.82 11 2,515.63 12 2,789.08 13 3,106.24 14 4,068.78 v 04302018.1 empire industries, inc. 39
FIG. 272 adjustable roller hanger Plain Carbon Steel (272B) Hot-Dip Galvanized (272HDG) T-316 Stainless Steel (272SX)* Electro-Galvanized (272G) T-304 Stainless Steel (272SS)* T-304 Stainless Steel with Short Roll (272SRSS) T-316 Stainless Steel with Short Roll (272SRSX) With Non-Conductive Roll (272NCR) T-304 Stainless Steel with Non-Condustive Roll (272SSNCR) T-316 Stainless Steel with Non-Condustive Roll (272SXNCR) Designed for the suspension of pipe where longitudinal movement of pipe may occur due to expansion and contraction, and where vertical adjustment may be necessary. Complies with Federal Specification WW-H-171-E (Type# 44), A-A- 1192 A (Type# 43) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 43). Specify figure number, roller type, finish and roller size. Please remember to consider insulation thickness when sizing rollers 272G Roller is Hot-Dip Galvanized. Hardware is Electro-Galvanized. * Available in 3-1/2, 5, 7 or 24 with short pattern roll only E.G. SS SX H.D.G. 2 30.19 35.53 -- -- 2-1/2 35.02 39.39 -- -- 3 33.09 41.66 -- -- 3-1/2 58.91 72.82 -- -- 4 40.41 58.06 5 56.98 72.59 6 63.57 91.78 7 89.73 133.95 8 113.80 153.87 10 133.15 196.66 12 217.89 298.31 14 386.74 485.50 16 415.40 579.60 18 598.73 866.45 20 958.05 1,103.29 24 -- -- FIG. 273 adjustable two-rod roller support E.G./SS/SX 2 50.29 2-1/2 55.96 3 58.40 3-1/2 61.81 Plain Carbon Steel (273B) Electro-Galvanized (273G) T-304 Stainless (273SS) T-316 Stainless (273SX) T-304 Stainless Steel with Short Roll (273SSSR) T-316 Stainless Steel with Short Roll (273SXSR) With Non-Conductive Roll (273NCR) T-304 Stainless Steel with Non-Condustive Roll (273SSNCR) T-316 Stainless Steel with Non-Condustive Roll (273SXNCR) Designed for the support of pipe where longitudinal movement may occur due to expansion and contraction and vertical adjustment of up to 6 inches may be necessary. Specify figure number, finish and roller size. Please remember to consider insulation thickness when sizing rollers 4 69.36 5 81.39 6 94.22 7 137.35 8 144.56 10 172.94 12 203.08 14 323.00 16 392.93 18 427.38 20 618.02 24 979.68 30 1,797.60 40 empire industries, inc. v 04302018.1
FIG. 275 roller chair E.G. H.D.G./SS/ SX Plain Carbon Steel (275B) Hot-Dip Galvanized (275HDG) T-316 Stainless Steel (275SX)* Electro-Galvanized (275G) T-304 Stainless Steel (275SS)* T-304 Stainless Steel with Short Roll (275SRSS) T-316 Stainless Steel with Short Roll (275SRSX) With Nonconductive Roll (275NCR) T-304 Stainless Steel with Non-Condustive Roll (275SSNCR) T-316 Stainless Steel with Non-Condustive Roll (275SXNCR) Designed for the support of pipe where longitudinal movement may occur due to expansion and contraction, and vertical adjustment is not necessary. May be bolted or welded to supporting member. Complies with Federal Specification WW-H-171-E (Type# 42), A-A- 1192 A (Type# 41) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 41). Specify figure number, finish and roller size. Please remember to consider insulation thickness when sizing rollers Mounting hardware not included. *Available in 3-1/2, 5, 7 or 24 with short pattern roll only 2 29.80 34.96 2-1/2 30.48 41.15 3 34.68 42.00 3-1/2 51.48 71.34 4 51.99 62.72 5 60.22 81.33 6 72.19 98.70 7 100.86 143.42 8 100.86 140.19 10 163.97 200.58 12 202.00 257.90 14 292.35 472.50 16 403.71 523.13 18 456.78 556.50 20 633.92 758.10 24 1,119.58 1,338.75 FIG. 277 adjuststable two rod roller hanger E.G. SS SX Plain Carbon Steel (277B) Electro-Galvanized (277G) T-304 Stainless Steel (277SS) T-316 Stainless Steel (277SX) T-304 Stainless Steel with Short Roll (277SSSR) T-316 Stainless Steel with Short Roll (277SXSR) With Non Conductive Roll (277NCR) T-304 Stainless Steel with Non-Condustive Roll (277SSNCR) T-316 Stainless Steel with Non-Condustive Roll (277SXNCR) Designed for the suspension of pipe where longitudinal movement may occur due to expansion and contraction, and vertical adjustment is necessary. Complies with Federal Specification WW-H-171-E (Type# 42), A-A- 1192 A (Type# 41) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 41). Specify figure number, finish and roller size. Please remember to consider insulation thickness when sizing rollers. 277G Roller is Hot-Dip Galvanized. Hardware is Electro-Galvanized. 2 27.41 33.54 -- -- 2-1/2 32.69 41.60 -- -- 3 32.75 45.35 -- -- 3-1/2 48.92 48.30 -- -- 4 39.33 57.04 5 42.57 61.41 6 52.50 76.28 7 74.58 95.24 8 82.52 116.58 10 84.79 139.22 12 140.13 191.50 14 193.37 297.80 16 259.38 387.48 18 296.38 463.76 20 417.73 633.80 24 659.74 1,038.65 30 1,223.28 1,758.78 -- -- v 04302018.1 empire industries, inc. 41
FIG. 279S pipe roll stand Plain Carbon Steel (279SB) Hot-Dip Galvanized (279SHDG) T-304 Stainless Steel (279SSS) T-316 Stainless Steel (279SSX) With Non Conductive Roll (279SNCR) Designed for the support of pipe where longitudinal movement may occur due to expansion and contraction and vertical adjustment of up to 6 inches may be necessary. Specify figure number, finish and roller size. Please remember to consider insulation thickness when sizing rollers Available Domestic. Stainless steel pipe roll hangers are recommended for applications where protection from a corrosive environment is required. FIG. 280S adjustable pipe roll stand 2-3-1/2 126.51 4-6 173.28 8-10 285.43 12-14 421.36 16-20 573.02 22-24 772.74 30 36-42 H.D.G./ SS/SX Plain Carbon Steel (280SB) Hot-Dip Galvanized (280SHDG) T-304 Stainless Steel (280SSS) T-316 Stainless Steel (280SSX) With Non Conductive Roll (280SNCR) Designed for the support of pipe where longitudinal movement may occur due to expansion and contraction, and where vertical adjustment is necessary. Complies with Federal Specification WW-H-171-E (Type# 47), A-A- 1192 A (Type# 46) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 46). Specify figure number, finish and roller size. Please remember to consider insulation thickness when sizing rollers Available Domestic. Stainless steel pipe roll hangers are recommended for applications where protection from a corrosive environment is required. FIG. 310 2-3-1/2 325.90 4-6 378.62 8-10 579.26 12-14 809.58 16-20 1,250.58 22-24 1,524.60 30 36-42 emlok adjustable adjustable swivel ring hanger H.D.G./ SS/SX Pre-Galvanized (310G) Plastic Coated (310PC) Pre -Galvanized, 3/16 Felt-lined: 1/2-2 (310GFL) Designed for the suspension of insulated and non-insulated pipe lines. The plastic coated band hanger protects the pipe from the steel surface of the hanger and is designed to reduce noise, vibration and prevents electrolysis between pipe and the hanger. Complies with Federal Specification WW-H-171-E (Type# 10), A-A-1192 A (Type# 10) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 10). UL approved on sizes 3/4-2. FM approved on sizes 3/4-2. Specify figure number, finish and pipe size. (knurl nut is imported) PRE-GALV PRE-GALV FELT LINED P.C. 1/2 3/8 1.25 3.72 9.99 100 3/4 3/8 1.25 3.72 10.10 100 1 3/8 1.25 3.92 10.27 100 1-1/4 3/8 1.31 3.92 10.67 100 1-1/2 3/8 1.36 4.53 11.41 100 2 3/8 1.53 4.60 12.49 100 2-1/2 1/2 7.66 -- 15.49 50 3 1/2 8.46 -- 18.11 50 3-1/2 1/2 12.77 -- 29.17 50 4 5/8 14.64 -- 34.62 25 5 5/8 16.97 -- 43.19 25 6 3/4 39.84 -- 36.66 20 8 3/4 47.68 -- 67.37 10 42 empire industries, inc. v 04302018.1
FIG. 310NFPA emlok adjustable swivel ring hanger, NFPA Pre-Galvanized (310NFG) Plastic Coated 1/2-8 (310NFPC) Pre-Galvanized, 3/16 Felt-lined: 1/2-8 (310NFFL) Designed for the suspension of non-insulated stationary pipe lines. Typically used as a pipe support for sprinkler piping. Hanger is manufactured to use minumum rod sizes permitted by NFPA. The plastic coated band hanger protects the pipe from the steel surface of the hanger and is designed to reduce noise, vibration and prevents electrolysis between pipe and the hanger. U.L. - U.L.C. listed and FM approved (2-1/2-8 ). Complies with Federal Specification WW-H-171-E (Type# 10), A-A-1192 A (Type# 10) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 10). Specify figure number, finish and pipe size. FIG. 310CT (knurl nut is imported) PRE-GALV PRE-GALV FELT LINED P.C. 1/2 3/8 1.25 3.72 9.99 100 3/4 3/8 1.25 3.72 10.10 100 1 3/8 1.25 3.92 10.27 100 1-1/4 3/8 1.31 3.92 10.67 100 1-1/2 3/8 1.36 4.53 11.41 100 2 3/8 1.45 4.60 12.49 100 2-1/2 3/8 3.18 7.37 13.74 50 3 3/8 3.29 7.71 15.95 50 3-1/2 3/8 4.20 10.08 25.71 50 4 3/8 3.80 -- 30.48 25 5 1/2 7.61 -- 38.14 25 6 1/2 7.95 -- 58.46 20 8 1/2 11.69 -- 86.44 10 10 1/2 65.72 -- -- 10 emlok adjustable swivel ring hanger for copper tubing TUBE COPPER PLATED EPOXY COATED Copper Epoxy Coated Copper Gard: Imported (310CTI) Copper Plated (310CT) Designed for the suspension of non-insulated, stationary copper lines. Complies with Federal Specification WW-H-171-E (Type# 10), A-A-1192 A (Type# 10) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 10). Specify figure number, finish and tube size. FIG. 310SS/SX excluding 310CTI (knurl nut is imported) emlok adjustable swivel hanger, stainless steel 1/2 3/8 2.38 2.10 100 3/4 3/8 2.44 2.16 100 1 3/8 2.44 2.21 100 1-1/4 3/8 2.50 2.38 100 1-1/2 3/8 2.55 2.44 100 2 3/8 2.89 2.50 100 2-1/2 1/2 6.92 6.07 50 3 1/2 7.95 7.15 50 3-1/2 1/2 14.59 9.08 50 4 1/2 10.44 9.82 25 5 1/2 19.01 21.34 25 6 1/2 22.48 21.91 25 SS (OD) SX (OD) SS (IPS) SX (IPS) T-304 Stainless Steel, IPS 1/2-6 (310SS) T-304 Stainless Steel, OD 1/2-4 (310ODSS) T-316 Stainless Steel, IPS 1/2-6 (310SX) T-316 Stainless Steel, OD 1/2-4 (310ODSX) Designed for the suspension of insulated and non-insulated pipe lines. Specify figure number, size type, finish and pipe size. (knurl nut is imported) 1/2 3/8 17.22 21.42 15.71 20.42 100 3/4 3/8 17.64 22.58 16.54 21.51 100 1 3/8 19.85 24.62 18.03 23.45 100 1-1/4 3/8 20.27 26.25 19.22 24.98 100 1-1/2 3/8 21.53 27.41 20.08 26.10 100 2 3/8 22.73 28.72 21.03 27.33 100 2-1/2 3/8 33.08 40.43 33.47 43.51 100 3 3/8 38.85 47.51 34.26 44.53 50 4 3/8 -- -- 38.98 50.67 50 5 3/8 -- -- 94.08 142.28 50 6 3/8 -- -- 108.68 148.05 50 v 04302018.1 empire industries, inc. 43
FIG. 320I / 320 turnbuckle Plain Carbon Steel: Imported (320BI) Hot-Dip Galvanized: Imported (320HDGI) Plain Carbon Steel (320B) Hot-Dip Galvanized (320HDG) T-316 Stainless Steel (320SX) To provide up to 6 inches of adjustment. Normally tapped for UNC-2A thread (standard). Complies with Federal Specification WW-H-171-E (Type# 13), A-A- 1192 A (Type# 13) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 13). Specify figure number, finish and size When figure 320I is supplied hot-dip galvanized, it is not tapped oversize. PRICES ARE FOR IMPORTED. ALL DOMESTIC. FIG. 420 pipe saddle support H.D.G. 3/8 18.50 33.09 1/2 26.90 41.83 5/8 36.38 57.49 3/4 45.29 63.00 7/8 69.98 99.49 1 82.01 119.87 1-1/8 152.73 255.06 1-1/4 152.79 255.18 1-1/2 254.44 618.14 Plain Carbon Steel (420B) Designed to be used in conjunction with a base stand to support pipe running close to the floor. Complies with Federal Specification WW-H-171-E (Type# 37), A-A-1192 A and Manufacturers Standardization Society MSS SP- 58 and SP-69 (Type# 36). Specify figure number, finish and pipe size Base stand can be ordered separately (requires accurate center line of pipe to floor dimension). Larger sizes available - FIG. 421 2 116.75 3 142.86 4 159.94 5 175.55 6 182.42 8 195.13 10 218.74 12 238.66 adjustable pipe saddle support with threaded coupling Plain Carbon Steel (421B) Designed to be used in conjunction with a base stand to support pipe running close to the floor. Specify figure number, finish and pipe size Base stand can be ordered separately (requires accurate center line of pipe to floor dimension 2 150.58 3 181.56 4 196.32 5 238.38 6 281.17 8 343.66 10 447.41 12 450.54 44 empire industries, inc. v 04302018.1
FIG. 422 adjustable pipe support Plain Carbon Steel (422B) Electro-Galvanized (422G) Designed to be used in conjunction with a base stand to support pipe running close to the floor. Threaded stud and nut provide adjustability. Specify figure number, finish and pipe size Base stand can be ordered separately (requires accurate center line of pipe to floor dimension). FIG. 425 adjustable pipe support Plain Carbon Steel (425B) Hot-Dip Galvanized (425HDG) T-304 Stainless Steel (425SS) T-316 Stainless Steel (425SX) Designed to be used in conjunction with a base stand to support pipe running close to the floor. U-bolt secures pipe to saddle. Complies with Federal Specification WW-H-171-E (Type# 37), A-A-1192 A (Type# 36) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 36). Specify figure number, finish and size Specify size, figure number and finish. Base stand ordered separately. Requires accurate center line of pipe to floor dimension ( L ). FIG. 426 adjustable pipe saddle support 2 118.11 3 134.06 4 150.58 5 165.50 6 201.88 8 230.38 10 275.21 12 296.38 2-1/2 201.60 3 203.19 3-1/2 236.28 4 244.85 5 274.25 6 323.23 8 421.14 10 528.92 12 607.24 14 959.93 16 1,096.88 18 1,274.42 20 1,912.53 24 2,296.89 H.D.G./ SS/SX H.D.G./ SS/SX 2-1/2 397.52 3 399.00 4 477.72 Plain Carbon Steel (426B) Hot-Dip Galvanized (426HDG) T-304 Stainless Steel (426SS) T-316 Stainless Steel (426SX) Designed to be used in conjunction with a base stand to support horizontal pipe. Straight cut pipe thread on nipple provides adjustability. Complies with Federal Specification WW-H-171-E (Type# 39), A-A- 1192 A (Type# 38) and Manufacturers Standardization Society MSS SP 58 and SP 69 (Type#38). Specify figure number, finish and size Base stand ordered separately. Requires accurate center line of pipe to floor dimension ( L ). 5 519.44 6 530.16 8 590.04 10 678.41 12 700.49 14 912.48 16 1,058.40 18 1,440.43 20 1,822.80 v 04302018.1 empire industries, inc. 45
FIG. 427 adjustable pipe saddle support with u-bolt Plain Carbon Steel (427B) Hot-Dip Galvanized (427HDG) Designed to be used in conjunction with a base stand to support horizontal pipe. Straight cut pipe thread on nipple provides adjustability, u-bolt secures pipe to saddle. Specify figure number, finish and size Base stand ordered separately. Requires accurate center line of pipe to floor dimension ( L ). FIG. 428KT adjustable pipe support, kit 2-1/2 449.74 3 474.60 3-1/2 638.40 4 652.70 5 673.08 6 702.48 8 816.90 10 874.68 12 989.10 14 1,311.48 16 1,496.28 18 2,227.08 20 2,480.10 24 3,103.80 30 3,598.38 36 4,785.90 H.D.G. Hot-Dip Galvanized (428KTHDG) T-316 Stainless Steel: (428KTSX) Designed to support pipe horizontally. Straight cut pipe thread on nipple provides up to 4-1/2 inches of vertical adjustability. Complies with Manufatcturers Standardization Society MSS SP-58 (Type# 38) Specify figure number, finish and pipe size. Saddles accommodate ductile iron pipe and IPS. Support requires 2 schedule 40 (3 schedule 40 for sizes 14 and 16 )extension pipe (not supplied) to be cut in the field. FIG. 429KTU adjustable pipe saddle support with u-bolt, kit 2 3 4 6 8 10 12 14 16 H.D.G./SX H.D.G./SX Hot-Dip Galvanized (429KTHDG) T-316 Stainless Steel: (429KTSX) Designed to support pipe horizontally. Straight cut pipe thread on nipple provides up to 4-1/2 inches of vertical adjustability. Complies with Manufatcturers Standardization Society MSS SP-58 (Type# 38) Specify figure number, finish and pipe size. Saddles accommodate ductile iron pipe and IPS. Support requires 2 schedule 40 (3 schedule 40 for sizes 14 and 16 ) extension pipe (not supplied) to be cut in the field. 46 empire industries, inc. v 04302018.1 2 3 4 6 8 10 12 14 16
FIG. 430KTSF adjustable flange support, kit Hot-Dip Galvanized (430KTSFHDG) Designed to support Class 125 pipe flange horizontally. Straight cut pipe thread on nipple provides up to 4-1/2 inches of vertical adjustability. Complies with Manufatcturers Standardization Society MSS SP-58 (Type# 38) Specify figure number, finish and pipe size. Support requires 2 schedule 40 extension pipe (not supplied) to be cut in the field. FIG. 431KTSF adjustable bolt on flange support, kit 4 6 8 H.D.G. Hot-Dip Galvanized (431KTHDG) Designed to support pipe flange horizontally. Straight cut pipe thread on nipple provides up to 4-1/2 inches of vertical adjustability. Specify figure number, finish and pipe size. Support requires 2 schedule 40 extension pipe (not supplied) to be cut in the field. FIG. 450 heavy beam clamp assembly 4 6 8 H.D.G. Plain Carbon Steel (450B) Hot-Dip Galvanized (450HDG) T-304 Stainless Steel (450SS) T-316 Stainless Steel (450SX) With Weldless Eye Nut (450W) Designed to be used for the suspension of heavy loads from beams up to 16 inches wide and up to 1 inch thick. Normally used with figure 26, 26W eyerods or figure 13, 13I weldless eye nuts. Complies with Federal Specification WW-H-171-E (Type# 28 without links, Type #29 with links), A-A-1192 A (Type# 28 without links, Type #29 with links) and Manufacturers Standardization Society MSS SP-58 and SP-69 (Type# 28 without links, Type #29 with links). Specify figure number, finish clamp size and rod size ASTM A-36 carbon steel with ASTM A-235 class C eye-nut. W/EYE NUT 1 461.89 513.42 2 616.04 679.38 3 636.92 723.76 4 799.42 959.08 5 954.93 1,152.45 6 1,237.24 1,419.60 H.D.G./ SS/SX v 04302018.1 empire industries, inc. 47
FIG. 575 corporation eye bolt Plain Carbon Steel (575B) Electro-Galvanized (575G) Designed to be used with figure number 600 socket clamp. Specify figure number and finish FIG. 585 ductile lug Plain Ductile Iron: (585B) Designed to assist in restraining of mechanical joint fittings, valves, hydrants and pipes by threaded rods. Intalled between MJ Bell and MJ Gland. Specify figure number For use on sizes 4-16 FIG. 595 four bolt socket clamp Plain Carbon Steel (595B) Hot-Dip Galvanized (595HDG) Electro-Galvanized (595G) Designed to used to clamp mechanical joint or socket joint piping and fittings together to prevent separation or distortion of pipe lines under excessive water pressure. Complies with the requirements of the National Fire Protection Association standard NFPA 24 for outside protection. Specify figure number, finish and size. 48 empire industries, inc. v 04302018.1
FIG. 599 socket clamp washer Plain Carbon Steel (599B) Hot-Dip Galvanized (599HDG) Electro-Galvanized (599G) Designed to be used with figure 600 socket clamp, washer lugs hook around clamp bolts to secure tie rods within clamp legs. Specify figure number, finish and size. The 3/4 rod size socket clamp washer is a cast iron product with tab feature. This accomodates pipe sizes 4-12. The 1-11/2 rod size washer are a carbon steel flat style. These accomodate pipe sizes 14-24. 4-12 3/4 8.57 14 1 16 1-1/8 18 1-1/4 20 1-3/8 24 1-1/2 E.G./ H.D.G FIG. 600DIP socket clamp Plain Carbon Steel (600DIPB) Hot-Dip Galvanized (600DIPHDG) T-316 Stainless Steel (600DIPSX) Electro-Galvanized (600DIPG) T-304 Stainless Steel (600DIPSS) Designed to be used to clamp joints of underground AWWA ductile iron water lines to prevent joint separation due to excessive water pressure. Specify figure number, finish and size. 3 3/4 75.18 4 3/4 96.76 6 3/4 107.47 8 3/4 123.32 10 3/4 142.59 12 3/4 164.06 14 1 543.11 16 1-1/8 678.88 18 1-1/4 848.61 20 1-3/8 1,266.46 24 1-1/2 2,252.25 E.G./ H.D.G/ SS/SX FIG. 801 medium welded bracket Plain Carbon Steel (801B) Hot-Dip Galvanized (801HDG) T-316 Stainless Steel (801SX) Electro-Galvanized (801G) T-304 Stainless Steel (801SS) Recommended for the support of pipe loads up to 1500 lbs Constructed of facing angle iron with 1 space. The bracket provides maximum lateral adjustment when carrying or suspending pipe. Complies with Federal Specification WW-H-171-E (Type# 33), A-A- 1192 A (Type# 32) and Manufacturers Standardization Society MSS SP 58 and SP 69 (Type#32). Specify figure number, finish and size number. BRACKET 1 474.26 2 566.72 3 828.02 v 04302018.1 empire industries, inc. 49
FIG. 802 heavy welded bracket Plain Carbon Steel (802B) Hot-Dip Galvanized (802HDG) T-316 Stainless Steel (802SX) Electro-Galvanized (802G) T-304 Stainless Steel (802SS) Recommended for the support of pipe loads up to 3000 lbs Constructed of facing angle iron with 1 space. The bracket provides maximum lateral adjustment when carrying or suspending pipe. Complies with Federal Specification WW-H-171-E (Type# 34), A-A-1192 A (Type# 33) and Manufacturers Standardization Society MSS SP 58 and SP 69 (Type# 33). Specify figure number, finish and size number. FIG. 820 & 820C light welded steel bracket and clip BRACKET 1 617.00 2 779.04 3 1,100.12 4 1,426.64 5 2,308.58 6 2,615.52 Plain Carbon Steel (820B) Hot-Dip Galvanized (820HDG) T-316 Stainless Steel (820SX) Electro-Galvanized (820G) T-304 Stainless Steel (820SS) Recommended for the suspension of hanger rod for support of light loads up to 750 lbs. Rod can be suspended at any point along the length of the bracket, thus providing horizontal adjustment, using figure #820C clip which consists of two steel plates joined by a bolt and nut in one end. Fig. 820 complies with Federal Specification WW-H-171-E (Type# 32), A-A-1192 A (Type# 31) and Manufacturers Standardization Society MSS SP 58 and SP 69 (Type# 31). Specify figure number, finish and size number Piping suspended from FIG. 820C clip shall not exceed 3-1/2 in diameter. Side clip (FIG. 820C) to be ordered separately. FIG. 900 nailing sleeve 820 LIGHT WELDED STEEL BRACKET 1 146.09 2 151.48 3 205.69 820C CLIP FOR 820 BRACK- ET 1 15.72 2 18.90 Electro-Galvanized (900G) When attached to roof decking, sleeve provides a channel for piping, eliminating the need to core drill. Optional tabs facilitate fastening to deck. Optional covers seal out wet cement during pour and safely cover sleeve until pipe installation. Specify diameter, height, and figure number, with or without tabs. Covers must be ordered separately. 50 empire industries, inc. v 04302018.1
FIG. 909 & 909I forged steel clevis excluding 909I Plain Carbon Steel: Import (909BI) T-316 Stainless Steel (909SX) Hot-Dip Galvanized: Import (909HDGI) Plain Carbon Steel (909B) Electro-Galvanized (909G) Hot-Dip Galvanized (909HDG) Designed for use on high temperature piping installations. T-316 Stainless Steel (909SX) Complies with Federal Specification WW-H-171-E (Type# 14), A-A-1192 A (Type# 14) and Manufacturers Standardization Society MSS SP 58 and SP 69 (Type# 14). Specify size number, rod size, finish and part number. If other than standard dimension sizes required, specify size number, rod size, pin size and grip. Forged clevis are standardly supplied with pin and cotter pins. When figure number 909 I is supplied hot-dip galvanized the threading is not tapped oversize. BODY AVAILABLE TAP PRICE / EACH IMPORTED H.D.G 2 3/8, 1/2, 5/8 60.84 76.17 2-1/2 3/4, 7/8 135.99 153.64 3 1, 1-1/8, 1-1/4 220.10 247.57 3-1/2 1-1/2 381.86 FIG. 910 pipe sleeve with welded lugs FIG. 915 waterproof sleeve Plain Carbon Steel (910B) Electro-Galvanized (910G) When attached to concrete forms, sleeve provides smooth sealable channel for piping, eliminating the need to core drill. Nailing lugs facilitate fastening to forms. Specify pipe size (A dimension), length, figure number and finish. PRICED ON APPLICATION v 04302018.1 Plain Carbon Steel (915B) Electro-Galvanized (915G) When installed in concrete forms, sleeve provides smooth, sealable channel for piping. Water stop prevents water migration around outside of sleeve. Specify nominal pipe size (A dimension), overall length, B dimension, figure number and finish. PRICED ON APPLICATION empire industries, inc. 51
FIG. 1900-1905 pipe covering protection saddle series Plain Carbon Steel (1900B) Hot-Dip Galvanized (1900HDG) T-316 Stainless Steel (1900SX) Electro-Galvanized (1900G) T-304 Stainless Steel (1900SS) 1 Insulation (1900) 1-1/2 Insulation (1901) 2 Insulation (1902) 2-1/2 Insulation (1903) 3 Insulation (1904) 4 Insulation (1905) Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Complies with Federal Specification WW-H-171-E (Type# 40A and 40B), A-A-1192 A (Type# 39A and 39B) and Manufacturers Standardization Society MSS SP 58 and SP 69 (Type#39A and 39B). Specify figure number, finish and insulation size. EG, HDG, SS, SX PRICED ON APPLICATION 1900 1 INSULATION 1/2 27.47 3/4 27.47 1 27.47 1-1/4 27.47 1-1/2 29.06 2 29.06 2-1/2 29.06 3 33.32 3-1/2 38.14 4 38.14 5 38.14 6 55.28 8 70.83 10 70.83 12 117.54 1901 1-1/2 INSULATION 3/4 32.86 1 32.86 1-1/4 32.86 1-1/2 32.86 2 32.86 2-1/2 38.71 3 38.71 3-1/2 38.71 4 38.71 5 38.71 6 71.23 8 83.66 10 83.66 12 127.93 14 127.93 16 145.52 18 159.60 20 184.18 24 224.70 1902 2 INSULATION 1903 2-1/2 INSULATION 1904 3 INSULATION 1905 4 INSULATION 3/4 36.27 1 36.27 1-1/4 36.27 1-1/2 40.24 2 40.24 2-1/2 40.24 3 44.72 3-1/2 44.72 4 44.72 5 44.72 6 71.74 8 84.96 10 95.98 12 140.19 14 140.19 16 186.16 18 186.16 20 200.58 24 225.78 1-1/4 47.28 1-1/2 47.28 2 47.28 2-1/2 50.23 3 50.23 3-1/2 54.49 4 54.49 5 54.49 6 89.68 8 100.35 10 151.20 12 151.20 14 151.20 16 196.44 18 213.97 20 213.97 24 252.23 2 52.16 2-1/2 52.16 3 63.00 3-1/2 63.00 4 63.00 5 63.00 6 109.26 8 109.26 10 119.70 12 167.21 14 167.21 16 202.22 18 202.22 20 230.43 24 268.74 4 86.72 5 86.72 6 142.63 8 142.63 10 153.13 12 204.66 14 204.66 16 256.54 18 263.01 20 332.14 24 355.98 52 empire industries, inc. v 04302018.1
FIG. 4000 SERIES pipe slide tees and slide plates Plain Carbon Steel (4000B) Hot-Dip Galvanized (4000HDG) T-304 Stainless (4000SS) T-316 Stainless (4000SX) Designed for the support of pipe where horizontal movement may occur due to expansion and contraction and a low coefficient of friction is required. May be welded or clamped to pipe. PLEASE CONTACT EMPIRE FOR MORE INFORMATION AND ORDERING. v 04302018.1 empire industries, inc. 53