REV: 1.2 TRAMPOLINE MANUAL

REV: 1.2 TRAMPOLINE MANUAL

TRAMPOLINE PARTS LIST: Item 8FT 10FT 12FT 14FT 16FT A 1 1 1 1 1 B 1 1 1 1 1 C 6 8 12 12 12 E 48 64 72 96 108 F 6 8 12 12 12 G 3 4 6 6 6 H 12 16 24 24 24 I 1 1 1 1 1 DIAGRAMS FOR PARTS:

TRAMPOLINE FRAME ASSEMBLY Refer to the Parts List for identification of parts The trampoline should be assembled by two physically capable adults. We recommend wearing suitable shoes for this task. Take care to maintain balance to prevent a fall. Follow all instructions and warnings carefully to avoid serious injury. 1. Lay out all the trampoline parts in groups, as shown in the picture. 2. Begin by attaching two leg extensions to form a U shape. Use the screws provided to fasten the legs. 3. Form a large circle with the top rail pieces With a second person holding the opposite end, bring both ends circle together and join them. T section screw holes should be on the Inside. 4. The top rail should look like this when complete with the T sections facing down. 5. Attach the U shaped leg parts to the top frame. Fasten into position with the screws provided. 6. Now the frame assembly is complete.

TRAMPOLINE MAT AND COVER ASSEMBLY Placement of springs, as illustrated in step 13, may require the help of a second person. WARNING: Springs will create high levels of tension when assembled. Please take care not to pinch your fingers and do not stand opposite to where the person is attaching the springs. 7. With the stitched portion facing down, lay the jumping mat inside the frame and attach a spring into one of the triangular rings on the mat. The more curved end of the spring is the side that attaches to the mat. Then attach the other end of the spring to the frame. This may take effort due to spring tension. 8. Repeat this step directly opposite where you attached the first spring. Then attach two more springs halfway between the first two, directly opposite each other. 9. Use the spring tool, as shown in the picture above. Springs under heavy tension may require more springs to be attached next to them every four or five holes along, so that the spring tension is evenly distributed. 10. Attach the remaining springs until all springs are placed on the frame securely. 11. Pull the black frame cover onto the outer edge of the top rail and pull it inwards so that the springs are covered. It should be fitted like a shower cap. Tie all the black straps to the top rail. Do not tie them to the springs. 12. The trampoline is now complete, ready for the net assembly.

DELUXE LADDER ASSEMBLY LADDER PARTS LIST ITEM 65CM 80CM 90CM 110CM A 2 2 2 2 B 2 2 2 2 C 4 4 4 4 D 1 1 1 1 A B C D 1: Slide the ladder poles (A) through the step risers (B). HOW TO ASSEMBLE THE LADDER 2: Adjust the risers so they line up with the holes in the ladder poles. 3: Put a bolt through each hole (C) and a nut on the the other side. Tighten with the supplied screw driver (D). 4: Your ladder is now ready to use.

TRAMPOLINE SAFETY NET USER MANUAL REV: 1.2

PARTS LIST: Ref. No Description 8ft 10ft 12ft 14ft 16ft 1 Bottom tube 6 8 12 12 12 2 Top tube 6 8 12 12 12 3 Top cap 6 8 12 12 12 4 Fork screw 12 16 24 24 24 5 Enclosure net 1 1 1 1 1 6 Fiberglass rod 6 8 12 12 12 7 Sleeve (for tube) 6 8 12 12 12 PHOTOS OF PARTS: 1. Bottom Tube: 2. Top Tube 3. Top cap 4. Fork Screw 5. Enclosure Net 6. Fiberglass Rod 7. Steel Tube Sleeves

The specifications and product features described in this manual are current at the time of printing. However, changes may be made in equipment, availability, specifications and features without notice. ASSEMBLY INSTRUCTIONS 1. Connect the bottom tube to the top tube. Top tube has a divot in one end, this is the side that needs to join with the bottom pole to lock them together tightly. Push the tube through the sleeve. The side of the sleeve that partially closed should be at the top. 2. Firmly fix the lower pole to the leg extension with the fork screw, then fasten the fork screw by wrenching on the nut. 3. Run the rods through the loops at the top of the safety net, then push the rods into the top caps as shown in the pictures below.

4. Repeating with the remaining rods until they all connect. To make the last connection, have one person stand on the opposite side from you, push the rods towards the centre of the ring until they are in line with each other and make the last connection, as shown in the picture below. 5. Raise the net up into position and clip the top caps into the tubes. Please make sure the net entry clips are on the outside before putting the net into position. 6. Pass the rope through the underside of the enclosure net and the triangular rings around the mat in a zig-zag style. Continue around the edge of the entire net, then tie a knot to secure the rope.

7. Your trampoline safety enclosure is now complete! If you need to install a basketball Hoop. Please follow the instructions below: 1,Open the basketball hoop set carton, take out all the parts, assemble the basketball hoop. Then install the bracket as shown below. 2, Choose one safety net pole, Take off the T shape connector of the pole enclosure. Let the whole basketball set through the net pole above, then install the T shape connector.

3, Basketball hoop kit is ready to use.

IMPORTANT For your safety, make sure to securely fasten enclosure entrance prior to using trampoline with safety net. PLEASE READ!!! IN CASE OF MISSING OR BROKEN PARTS, PLEASE CONTACT PLACE OF PURCHASE FOR ASSISTANCE. WARNING: The supplier is not liable for any injuries caused by using the trampoline. BEFORE YOU BEGIN USING YOUR TRAMPOLINE Read and understand all the information provided to you in this manual. As with all physical sports and activities, there is some risk of injury if care is not taken. To avoid injuries and ensure your future enjoyment of the trampoline, be sure to follow these safety rules and tips.

GENERAL SAFETY INSTRUCTIONS Please read and follow all instructions before you start using your trampoline. You should inspect the safety net before each use for bent steel tubes, torn mat, lose or broken springs and overall stability of the trampoline. Always ensure that the equipment is working normally and safely before you use your trampoline. Never have more than one person bouncing on the trampoline at one time. The safety net has been designed for use by only one person. Adult supervision is required for children using the trampoline. The safety net is not intended to replace adult supervision. This product is only intended for use at home. Do not use the trampoline in windy conditions. To prevent falls and entanglement, trampoline users should enter and exit carefully, using the door only. Adults should assist young children in and out of the safety net. SAFETY NET ASSEMBLY Please read the assembly instructions before beginning assembly. The safety net must be assembled by adults. Two or more people are required for assembly. Please refer to the table above for parts description and numbering. Before you start assembling, make sure you have all the parts listed. If you are missing any parts, please contact the retailer that you purchased the trampoline from. Wear gloves to protect your hands from pinching during assembly. When you are ready to start, make sure that you have plenty of space and a clean, dry area for assembly.