Full Size ed CUTON: You must read this before you proceed. NOTE : This ed is NOT a TOY. Keep your child / children at bay during the assembly process. The ED is EVY. To prevent injury to yourself or damage to the product a minimum of two adults are required whenever moving or lifting the product. No. Picture Description Qty Foldable eadboard 1 eadboard Foot 2 C Left Wing 1 D Right Wing 1 1 OF 13
E Footboard 1 F Left Side Front Panel with pre-attached material 2 G Left Side End Panel 2 Right Side Front Panel with pre-attached material 2 Right Side End Panel 2 Cross Slat (Labelled 'Face Up') 4 K Support Leg for Cross Slat 4 L Footboard Foot 2 M ed ack Seal 1 No. Picture Description Qty 1 olt (M8x60mm) 8 2 OF 13
2 olt (M8x3mm) 12 3 olt (M8x40mm) 3 4 olt (M8x2mm) 3 Spring Washer 21 6 Screw (M4x40mm) 9 Washer 21 8 llen Key 1 9 Screwdriver 1 efore eginning ssembly: Unpack and place all parts for clear visibility. 3 OF 13
Pack : ardware for assembly of ed. Comment:a ve provided one more of bolt,washer, spring washer,nut and screw. olt(1) olt(2) olt(3) olt(4) Spring Washer() Screw(6) Washer() llen Key(8) Screwdriver(9) OVERVEW Foldable eadboard() ed ack Seal(M) Left Wing(C) Left Side Front Panel with pre-attached material(f) Cross Slat() Right Wing(D) Left side end panel(g) eadboard Foot() Footboard(E) Right Side Front Panel with pre-attached material() Support Foot for Cross Slat(K) Right side end panel() Footboard Foot(L) 4 OF 13
This ed has multiple parts and may require up to some 60 minutes to assemble. To give you an overview of the ed parts, the above picture is to help you put the various ed parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Place the Foldable eadboard() onto a clean, non-marring surface. Unfold the eadboard(). The eadboard is eavy. Two adults are required whenever lifting and moving it. Make sure the fabric does not get stuck when unfolding the eadboard. Step 2 8 1 Secure the upper fold of the eadboard() using olts(1), Washers(), and Spring Washers() with llen Key(8). Do not fully tighten the olts. OF 13
Step 3 8 3 ttach eadboard Feet() to eadboard() using olts(3) and Washers() with llen Key(8). Only loosely tighten the olts ensuring the Feet can be turned. Step 4 Stand up the eadboard. Turn the Legs outwards as pictured above. Place the eadboard onto a clean, non-marring surface with its facing up. Tighten the olts on the Legs with llen Key(10) until secure. Two adults are required for moving the eadboard during this step. Step 6 OF 13
With assistance from your adult partner. Stand the eadboard up. Press down the folded panels flat with the eadboard(). Smooth out the cover with the palm of your hands: Smooth from Top to ottom; always starting from the Middle working to the Outer sides allowing the velcro tape to adhere to the flap on the eadboard(). This step works best with three adults. One person to steady the eadboard, the remaining two people press the folded panels and adhere the material. Step 6 8 2 With assistance from your adult partners, turn the eadboard so it's back side is facing. Secure the lower fold of the eadboard() using olts(2), Washers(), and Spring Washers() with llen Key(8). You may need to slap both sides of folded panels from the front to make the mountings on the folded panels align with the mountings on the eadboard. Tighten all the olts on the eadboard until secure. Step 2 D 8 C lign Left Wing(C) to the eadboard() on the mounting position,then attach by using olt(k), Washer(L), and Spring Washer(N) with llen Key(S). Then repeat to attach Right Wing (D). Tighten olts until secure. OF 13
Step 8 Velcro Velcro M Turn back the eadboard(), cover it with ed ack Seal(M).Smooth the Velcro of ed ack Seal(K) as shown. Step 9 8 1 2 4 ttach Right Side End Panel () to Right Side Front Panel with pre-attached material () using olt (1), olt (2),olt (4),Washer (),Spring Washer()with llen Key(8) as shown. Tighten the bolts. Repeat the same process with the Leftt Side End Panel(G) and Left Side Front Panel with pre-attached material(f). 8 OF 13
Step 10 With assistance from you adult partner.one person hold the Side panel. 2) dhere the material on the inside of Right Side End Panel(). 3) Smooth from Top to ottom to allowing the velcro tape to adhere to the flap on the Right Side End Panel(). Repeat the same process with the Left Side End Panel(G) Step 11 8 1 L L E ttach Footboard Foot() to Footboard(E) using olts(1), Washer (),Spring Washer()with llen Key(8). Repeat the same process with the remaining Footboard Feet(L). Tighten the olts until secure. 9 OF 13
Step 12 E G F G E ttach Left Side End Panel (G) to Footboard (E )and also attach Right Side End Panel () to Footboard(E) by sliding the iron plates onto the olts from Step 10 as shown. Caution: The metal card should be alignment card slot when install it,then press it lightly. Step 13 C D G F L E ttach Left Side Front Panel with pre-attached material (D) to Foldable eadboad () and also attach Right Side Front Panel with pre-attached material (F) to Foldable eadboad () by sliding the iron plates onto the olts from Step 11 as shown. 10 OF 13
Step 14 Step 14.1 Labelled "Face Up" side down Step 14.2 K Step 14.3 K Labelled "Face Up" side up 14.1 - Place the Cross Slat() facedown with face up" label down. 14.2 - ttach Support Legs(K) to the bottom of Cross Slat() by inserting the threaded stem in the Foot and turning clockwise until secure. 14.3 - Stand the Cross Slats upright. Repeat the same process with the remaining Cross Slats() and Support Legs(K). Step 1 G C F E L D K Labelled "Face Up" side up Put the Cross Slats() into the guide mountings of the Side Rails(D)(E) and Side Rails(F)(G). 11 OF 13
Step 16 C D 9 6 G K F E F L Secure the Cross Slats() to the Side Rails using Screws(6) with Screwdriver(9). Tighten Screws until secure. Step 1 Ensure that all olts are secured at all joints. Your ed is ready for use. This ed can only be used on a flat, level surface. 12 OF 13
What is Proposition 6? Proposition 6 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental ealth azard ssessment (OE) has deemed to cause cancer or other reproductive toxicity. Chemicals and elements on this list include wood dust, brass, and other everyday substances, which can be found in very common household items, such as: lamps, tableware, jewelry, crystal glasses, electric cords, beauty products, automobiles, and furniture. Why Did Find a Proposition 6 Warning on My ome Goods Product? We include Proposition 6 warnings on all of our products because there is always a chance that one of the 800- plus common chemicals and ingredients listed under this law could potentially be on our furniture or packing materials. We risk large fines under this law, if we don't include this warning. Should worry? We realize you may be worried finding this warning on our products, but we want to reassure you that the hazardous exposure limits for any of these chemicals have never been found on furniture products that we ve shipped to our customers. dditionally, this warning label is very common and can be found on almost every piece of furniture sold in the state of California. ust ow Common re Proposition 6 Warnings? Proposition 6 warnings have become so common in California that it is hard to take a trip to a local bank, grocery store, or restaurant without finding at least one warning. n fact, even the Disney Land Resort has a Proposition 6 warning: 13 OF 13