ASSEMBLY & DISASSEMBLY INSTRUCTIONS http://www.sunnen.com for SUNNEN MPS-ANR TOOL/DRIVESHAFT CONNECTIONS I-ANR-260 GENERAL The following instructions cover the assembly and disassembly of Sunnen Wide Range Modular Honing Tool when using with Sunnen AN OR ANR Style Hone Heads (see Figure 1). DRIVESHAFT EXTENSION ANR-741 (9.25"/235 mm) ANR-742 (19"/483 mm) ANR-744 (42.75"/1086 mm) ANR-746 (72.25"/1835 mm) HONE HEAD ANR Style - Bolt Together Style: Requires MPS-E2015 and MPS-2220A to connect to HTA U-Joint MPS-175 U-JOINT MPS-2230A MPS-ER22 MPS-2235A DRIVE & FEED EXTENSION MPS-E2015 (5.9"/150 mm) MPS-2220A Output Adapter HONE HEAD MPS-2220A Output Adapter MPS STYLE - SCREW TOGETHER: Connects directly to HTA U-Joint MPS-175 U-JOINT MPS-2230A MPS-ER22 MPS-2235A DRIVE & FEED EXTENSION MPS-E2015 (5.9"/150 mm) MPS-E2040 (15.7"/400 mm) MPS-E2100 (39.3"/1000 mm) MPS-E2160 (63"/1600 mm) ADAPTERS TO CONVERT MPS DRIVESHAFT TO BOLT TOGETHER CONFIGURATION (ANR STYLE) (OPTION) One of each part number required per MPS driveshaft. MPS-2211A Input Drive Adapter MPS-2212A Input Feed Adapter DRIVE SHAFT EXTENSION MPS-E MPS-2222A OutputFeed Adapter MPS-2221A Output Drive Adapter FIGURE 1, MPS-Style Driveshaft Comparision for use with AN/ANR-Style Hone Heads SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY. SUNNEN PRODUCTS COMPANY 7910 MANCHESTER ROAD ST. LOUIS, MO 63143, U.S.A. PHONE: 314-781-2100
ASSEMBLY INSTRUCTIONS ANR STYLE - BOLT TOGETHER STYLE: REQUIRES MPS-E2015 AND MPS-2220A TO CONNECT TO MPS/HTA U-JOINT GENERAL Assemble the Sunnen Wide Range Modular Honing Tool as follows (refer to the following Figures): WARNING ASSEMBLE HONING TOOL AS SHOWN. FAILURE TO INCLUDE DISASSEMBLY RINGS OR TO USE MORE THAN ONE RING PER FITTING COULD RESULT IN PERSONAL INJURY OR DAMAGE TO THE HONING TOOL AND EQUIPMENT. 1. Select MPS-E2015 Drive & Feed Extension, MPS-2200 Adapter Set, ANR Driveshaft Extension, & AN/ANR Style Hone Head. To obtain the necessary length of your Honing Tool, two or more ANR Driveshaft Extensions may be bolted together. (Refer to the following Figures & Table 1.) 2. Screw Input Yoke Adapter (MPS-2230A) with Disassembly Ring (MPS-E22) on threaded male end of Drive & Feed Extension (MPS-E2015). 3. Slide Universal Cover (MPS-2235A) on Drive & Feed Extension (MPS-E2015). DRIVESHAFT EXTENSION ANR-741 (9.25"/235 mm) ANR-742 (19"/483 mm) ANR-744 (42.75"/1086 mm) ANR-746 (72.25"/1835 mm) 6. Insert Hone Head Module on end of Output Adapter, ANR-Style Drive & Feed Extension, and secure with four Screws (provided). 4. Screw Output Adapter (MPS-2230A) with Output Feed Adapter and Disassembly Ring (MPS-E22) into threaded female end of Drive & Feed Extension (MPS-E2015). 5. Bolt Driveshaft Extension (ANR- )on end of Output Adapter using the four Screws (provided). 7. Install Honing Tool on the Machine by aligning Input Yoke Adapter on Honing Tool with Drive Ring, and guide adapter onto Hex Shaft. 8. Rotate input Yoke Adapter (clockwise) to engage and Lock into the Drive Ring on the Spindle Nose.. 2
ASSEMBLY INSTRUCTIONS (CONT D) ANR STYLE - BOLT TOGETHER STYLE: REQUIRES MPS-E2015 AND MPS-2220A TO CONNECT TO MPS/HTA U-JOINT TABLE 1, ANR Style - Bolt Together Style - Requires MPSE2015 & MPS2220A to connect to HTA U-Joint Part Number Qty Description 1 MPS-E2015 1...Drive & Feed Extension (5.9 in. / 150 mm) 2 MPS-2220A 1...Output Flange (for connecting Extension to ANR-Style Driveshaft) 3 ANR- 1...Driveshaft Extension (select one or more) ANR-741 -...Driveshaft Extension (9.25 in. / 235 m) ANR-742 -...Driveshaft Extension (19.0 in. / 483 mm) ANR-744 -...Driveshaft Extension (42.75 in. / 1086 mm) ANR-746 -...Driveshaft Extension (72.25 in. / 1835 mm) 9. Slide Universal Cover into operating position over Input Yoke Adapter. 10. Pull back Release Ring and tilt hone body as shown. 11. Pull the ANR-210 Pinion all the way out. 12. Place the racks of the stone and guide assemblies in holes marked "X" as shown. 13. Put ANR-2l0 Pinion back in place. 14. Pull back Release Ring, line up hone body, and allow Release Ring to return to engaged position. CAUTION Stone Assemblies and Guides MUST be firmly seated on Master Holder Assemblies to prevent them from breaking loose during the honing operation and damaging the workpiece or the Honing Tool. 3
ASSEMBLY INSTRUCTIONS MPS STYLE - SCREW TOGETHER: CONNECTS DIRECTLY TO MPS/HTA U-JOINT GENERAL Assemble the Sunnen Wide Range Modular Honing Tool as follows (refer to the following Figures): WARNING ASSEMBLE HONING TOOL AS SHOWN. FAILURE TO INCLUDE DISASSEMBLY RINGS OR TO USE MORE THAN ONE RING PER FITTING COULD RESULT IN PERSONAL INJURY OR DAMAGE TO THE HONING TOOL AND EQUIPMENT. 1. Select MPS-Style Drive & Feed Extension, MPS-2200 Adapter Set, & AN/ANR Style Hone Head.. To obtain the necessary length of your Honing Tool, two or more MPS-Style Drive & Feed Extensions may be screwed together (Refer to the following Figures and Table 2 & 3.). DRIVE & FEED EXTENSION MPS-E2015 (5.9"/150 mm) MPS-E2040 (15.7"/400 mm) MPS-E2100 (39.3"/1000 mm) MPS-E2160 (63"/1600 mm) 2. Screw Input Yoke Adapter (MPS-2230A) with Disassembly Ring (MPS-E22) on threaded male end of Drive & Feed Extension (MPS-E ). 3. Slide Universal Cover (MPS-2235A) on Drive & Feed Extension (MPS-E2015). 6. Install Honing Tool on the Machine by aligning Input Yoke Adapter on Honing Tool with Drive Ring, and guide adapter onto Hex Shaft. 7. Rotate input Yoke Adapter (clockwise) to engage and Lock into the Drive Ring on the Spindle Nose.. 4. Screw Output Adapter (MPS-2220A) with Output Feed Adapter and Disassembly Ring (MPS-E22) 1nto threaded female end of Drive & Feed Extension (MPS-E2015). 5. Insert Hone Head Module on end of Output Adapter and secure with four Screws (provided). WARNING FAILURE TO HAND TIGHTEN ALL FITTINGS COULD RESULT IN PERSONAL INJURY OR DAMAGE TO THE HONING TOOL AND EQUIPMENT. 8. Using the Hone Head Module as a lever, hand tighten Drive and Feed Assembly by turning Hone Head Module clockwise to ensure ail fittings are tight. 4
ASSEMBLY INSTRUCTIONS (CONT D) MPS STYLE - SCREW TOGETHER: CONNECTS DIRECTLY TO MPS/HTA U-JOINT TABLE 2, MPS Style - Screw Together - connects directly to HTA U-Joint Part Number Qty Description 1 MPS-E 1...Drive & Feed Extension (select one or more) MPS-E2015 -...Drive & Feed Extension (5.9 in. / 150 mm) MPS-E2040 -...Drive & Feed Extension (15.7 in. / 400 mm) MPS-E2100 -...Drive & Feed Extension (39.3 in. / 1000 mm) MPS-E2160 -...Drive & Feed Extension (63 in. / 1600 mm) 2 MPS-2200 1...Adapter Set includes - MPS-2230A 1...Input Yoke - MPS-2235A 1...Universal Cover - MPS-2220A 1...Output Adapter (for connecting Extension to ANR-160A Hone Head) - MPS-ER22 2...Disassembly Rings (pkg of 6) TABLE 3, Adapters to Convert MPS Driveshaft to Bolt Together ANR Style Configuration Driveshaft Part Number Qty* Description 1 MPS-2211A 1...Input Drive Adapter 2 MPS-2212A 1...Input Feed Adapter 3 MPS-2221A 1...Output Drive Adapter 4 MPS-2222A 1...Output Feed Adapter * One of each part number required per MPS Drive & Feed Extension 9. Slide Universal Cover into operating position over Input Yoke Adapter. 10. Pull back Release Ring and tilt hone body as shown. 11. Pull the ANR-210 Pinion all the way out. 12. Place the racks of the stone and guide assemblies in holes marked "X" as shown. 13. Put ANR-2l0 Pinion back in place. 14. Pull back Release Ring, line up hone body, and allow Release Ring to return to engaged position. CAUTION Stone Assemblies and Guides MUST be firmly seated on Master Holder Assemblies to prevent them from breaking loose during the honing operation and damaging the workpiece or the Honing Tool. 5
DISASSEMBLY INSTRUCTIONS GENERAL Disassemble the Sunnen Wide Range Modular Honing Tool as follows refer to the following Figures): WARNING SAFETY GLASSES MUST BE WORN WHEN REMOVING DISASSEMBLY RINGS. USE CARE WHEN REMOVING RINGS TO PREVENT PERSONAL INJURY OR DAMAGE TO HONING TOOL AND EQUIPMENT. 3. Use A Center Punch (or Chisel) to break Disassembly Rings at notch. Remove Disassembly Rings by driving out with a Flat Punch (or Chisel). Discard old rings. 1. Remove Master Holder Assemblies from Adapter Block Sets by loosening two (2) Socket Head Screws using 3/32 Hex Wrench. Remove Adapter Block Sets from Stone & Guide Extensions in Hone Body by loosening three (3) Socket Head Cap screws using 5/16 Hex Wrench. 4. Unscrew Input Yoke Adapter from Drive & Feed Extension. 2. Remove Honing Tool from Machine by pressing Release Pins and turning Adapter counterclockwise to unlock it from Drive Ring. Slide Adapter off Hex Shaft. 5. Unscrew Hone Head Module from Drive & Feed Extension. Inspect parts for signs of wear or damage and replace as necessary.
ANR Style Hone Head Part Number Qty Description 19 ANR-160A 1...Hone Head Assembly consists of: 20 ANR-207A 2...Setscrews, Self-Locking (Pkg. of 2) 21 ANR-170A* 1...Inner Feed Assembly consists of: 22 ANR-189A* 2...Drive Pin (3/16" Dia. Steel)(Pkg. of 2) 23 ANR-195A* 1...Feed Shaft End Assembly, Spring and Pin 24 ANR-176A* 1...Coupling 25 ANR-187A* 1...Ball Link Assembly 26 ANR-165A* 1...Drive Housing Assembly 27 ANR-210A 1...Pinion Adjustment Assembly 28 AN-620A 1...Ring Set consists of: 29 AN-621A 2...Screws (Pkg. of 2) 30 AN-624A 2...Screws (Pkg. of 2) 31 AN-623A 2...Spacers (Pkg. of 2) 32 - - - 1...Ring 33 AN-604 1...Body Assembly 14 MSN-177A 4...Screws (10-32 x 5/8" SHCS)(Pkg. of 4) 7
RECOMMENDED STONE SETS SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY. Sunnen reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing. Should any discrepancy of information arise, Sunnen recommends that user verify discrepancy with Sunnen before proceeding. SUNNEN PRODUCTS COMPANY 7910 Manchester Road, St. Louis, MO 63143 U.S.A. Phone: 314-781-2100 Fax: 314-781-2268 U.S.A. Toll-Free Sales and Service Automotive: 1-800-772-2878 Industrial: 1-800-325-3670 International Division Fax: 314-781-6128 http://www.sunnen.com e-mail: sunnen@sunnen.com UK SUNNEN PRODUCTS LTD. Phone: ++ 44 1442 39 39 39 Fax: ++ 44 1442 39 12 12 www.sunnen.co.uk e-mail: hemel@sunnen.co.uk SWITZERLAND SUNNEN AG Phone: ++ 41 71 649 33 33 Fax: ++ 41 71 649 34 34 www.sunnen.ch e-mail: info@sunnen.ch CHINA SHANGHAI SUNNEN MECHANICAL CO., LTD. Phone: 86 21 5 813 3322 Fax: 86 21 5 813 2299 www.sunnensh.com e-mail: sales@sunnensh.com SUNNEN ITALIA S.R.L. Phone: 39 02 383 417 1 Fax: 39 02 383 417 50 www.sunnenitalia.com e-mail: sunnen@sunnenitalia.com FRANCE SUNNEN SAS Phone: +33 01 69 30 0000 Fax: +33 01 69 30 1111 www.sunnen.fr e-mail: info@sunnen.fr RUSSIA SUNNEN RUS Phone: +7 495 258 43 43 Fax: +7 495 258 91 75 www.sunnen.ru e-mail: sunnen@sunnen-russia.ru CZECH REPUBLIC SUNNEN S.R.O. Phone: +420 383 376 317 Fax: +420 383 376 316 www.sunnen.cz e-mail: sunnen@sunnen.cz POLAND SUNNEN POLSKA SP. Z O.O. Phone: +48 22 814 34 29 Fax: +48 22 814 34 28 www.sunnen.pl Email: sunnen@sunnen.pl PRINTED IN U.S.A. 0909 COPYRIGHT SUNNEN PRODUCTS COMPANY 2009, ALL RIGHTS RESERVED