echnicl dt sheet SR24A-MF Prmeterisle rotry ctutor for ll vlves Nominl torque 20 Nm Nominl voltge AC/DC 24 V Control Modulting DC (0)2...10 V Vrile Position feedck DC 2...10 V Vrile echnicl dt Electricl dt Nominl voltge AC/DC 24 V Nominl voltge frequency 50/60 Hz Nominl voltge rnge AC 19.2...28.8 V / DC 21.6...28.8 V Power consumption in opertion 4 W Power consumption in rest position 1.25 W Power consumption for wire sizing 6 VA Connection supply / control Cle 1 m, 4 x 0.75 mm² Prllel opertion es (note the performnce dt) Functionl dt orque motor Min. 20 Nm Positioning signl DC 0...10 V Positioning signl note Input impednce 100 kω Control signl vrile Open-close 3-point (AC only) Modulting (DC 0...32 V) Operting rnge DC 2...10 V Operting rnge vrile Strt point DC 0.5...30 V End point DC 2.5...32 V Position feedck DC 2...10 V Position feedck note Mx. 0.5 ma Position feedck vrile Strt point DC 0.5...8 V End point DC 2.5...10 V Position ccurcy ±5% Mnul override Ger disenggement with push-utton, cn e locked Running time motor 90 s / 90 Motor running time vrile 90...350 s Adption setting rnge mnul (utomtic on first power-up) Adption setting rnge vrile No ction Adption when switched on Adption fter pushing the ger disenggement utton Override control MAX (mximum position) = 100% MIN (minimum position) = 0% ZS (intermedite position, AC only) = 50% Override control vrile MAX = (MIN + 33%)...100% MIN = 0%...(MAX 33%) ZS = MIN...MAX Sound power level motor 45 db(a) Position indiction Mechniclly, pluggle Sfety Protection clss IEC/EN III Sfety extr-low voltge Protection clss L L Clss 2 Supply Degree of protection IEC/EN IP54 Degree of protection NEMA/L NEMA 2, L Enclosure ype 2 EMC CE ccording to 2004/108/EC Certifiction IEC/EN IEC/EN 60730-1 nd IEC/EN 60730-2-14 Certifiction L clus ccording to L 60730-1A, L 60730-2- 14 nd CAN/CSA E60730-1:02 Mode of opertion ype 1 Rted impulse voltge supply / control 0.8 kv www.elimo.eu SR24A-MF en-g 2015-04-28 suject to chnges 1
echnicl dt Sfety Control pollution degree 3 Amient temperture -30...50 C Non-operting temperture -40...80 C Amient humidity 95% r.h., non-condensing Mintennce Mintennce-free Weight Weight pprox. 0.90 kg Sfety notes! his device hs een designed for use in sttionry heting, ventiltion nd ir conditioning systems nd is not llowed to e used outside the specified field of ppliction, especilly in ircrft or in ny other irorne mens of trnsport. Only uthorised specilists my crry out instlltion. All pplicle legl or institutionl instlltion regultions must e complied during instlltion. he switch for chnging the direction of rottion my only e operted y uthorised specilists. he direction of rottion must not in prticulr e reversed in frost protection circuit. he device my only e opened t the mnufcturer s site. It does not contin ny prts tht cn e replced or repired y the user. Cles must not e removed from the device. he device contins electricl nd electronic components nd is not llowed to e disposed of s household refuse. All loclly vlid regultions nd requirements must e oserved. Product fetures Principle of opertion Prmeterisle ctutors Simple direct mounting Mnul override High functionl reliility Adjustle ngle of rottion Home position Adption nd synchronistion he ctutor is connected with stndrd modulting signl of DC 0...10V nd trvels to the position defined y the positioning signl. Mesuring voltge serves for the electricl disply of the vlve position 0...100% nd s slve control signl for other ctutors. he fctory settings cover the most common pplictions. Input nd output signls nd other prmeters cn e ltered with the PC-ool MF-P or with the Service tool ZH E. Strightforwrd direct mounting on the ll vlve with only one centrl screw. he ssemly tool is integrted in the plug-in position indiction. he mounting orienttion in reltion to the ll vlve cn e selected in 90 steps. Mnul override with push-utton possile (the ger is disengged for s long s the utton is pressed or remins locked). he ctutor is overlod protected, requires no limit switches nd utomticlly stops when the end stop is reched. Adjustle ngle of rottion with mechnicl end stops. he first time the supply voltge is switched on, i.e. t the time of commissioning, the ctutor crries out n dption, which is when the operting rnge nd position feedck djust themselves to the mechnicl setting rnge. he ctutor then moves into the position defined y the positioning signl. Fctory setting: 2 (counter-clockwise rottion). An dption cn e triggered mnully y pressing the Adption utton or with the PC-ool. Both mechnicl end stops re detected during the dption (entire setting rnge). Automtic synchronistion fter pressing the gerox disenggement utton is configured. he synchronistion is in the home position (0%). he ctutor then moves into the position defined y the positioning signl. A rnge of settings cn e dpted using the PC-ool (see MF-P documenttion) 2 SR24A-MF en-g 2015-04-28 suject to chnges www.elimo.eu
Accessories Description Electricl ccessories Auxiliry switch, dd-on, 1 x SPD S1A Feedck potentiometer 200 Ohm, dd-on P200A Feedck potentiometer 500 Ohm, dd-on P500A Feedck potentiometer 2.8 kohm, dd-on P2800A Feedck potentiometer 5 kohm, dd-on P5000A Service ools Description Service ool, for MF/MP/Modus/LonWorks ctutors nd VAV- Controller Belimo PC-ool, softwre for djustments nd dignostics Adpter to Service-ool ZH ype ype ZH E MF-P MF-C Electricl instlltion! Wiring digrms AC/DC 24 V, modulting Notes Connection vi sfety isolting trnsformer. Prllel connection of other ctutors possile. Oserve the performnce dt. Direction of rottion switch is covered. Fctory setting: Direction of rottion 2. DC (0)2 10 V DC 2 10 V Cle colours: 1 = lck 2 = red 3 = white 5 = ornge Functions Functions with sic vlues (conventionl mode) Override control with AC 24 V with rely contcts Override control with AC 24 V with rotry switch c (DC 0...10 V) 0% ZS 50% 100% (DC 0...10 V) 0% ZS 50% c 100% www.elimo.eu SR24A-MF en-g 2015-04-28 suject to chnges 3
Functions Remote control 0...100% with positioner SG.. Minimum limit with positioner SG.. Z 1 2 3 4 SGA24 SGF24 SGE24 Z 1 2 3 4 SGA24 SGF24 SGE24 10 [V] (DC 0...10 V) min 0 [%] 0 100 Follow-up control (position-dependent) Position indiction DC (0)2 10 V DC 2 10 V ZAD24 1 2 3 4 1) (1) Adpting the direction of rottion Control with 4...20 ma vi externl resistor Functionl check 500 Ω ( ) (+) 4 20 ma DC 2 10 V Cution: he operting rnge must e set to DC 2...10 V. he 500 Ω resistor converts the 4...20 ma current signl to voltge signl DC 2...10 V Procedure 1. Connect 24V to connections 1 nd 2 2. Disconnect connection 3: with direction of rottion 1: Actutor rottes to the left with direction of rottion 2 Actutor rottes to the right 3. Short-circuit connections 2 nd 3: Actutor runs in opposite direction Functions for ctutors with specific prmeters (Prmetristion with PC-ool necessry) Override control nd limiting with AC 24 V with rely contcts Override control nd limiting with AC 24 V with rotry switch c d e (DC 0...10 V) Close 1) MIN ZS MAX Open (DC 0...10 V) Close 1) MIN ZS MAX Open c d e 1) Cution: his function is only gurnteed if the strt point of the operting rnge is defined s min. 0.5 V. 4 SR24A-MF en-g 2015-04-28 suject to chnges www.elimo.eu
Functions Control open-close Control 3-point with AC 24 V stop Operting controls nd indictors 4 1 Adption 1 2 2 Power 3 Sttus 1 Direction of rottion switch Switch over: Direction of rottion chnges 2 Push-utton nd LED disply green Off: No power supply or mlfunction On: In opertion Press utton: riggers ngle of rottion dpttion, followed y stndrd mode 3 Push-utton nd LED disply yellow Off: Stndrd mode On: Adpttion or synchronising process ctive Press utton: No function 5 4 Ger disenggement utton Press utton: Ger disengges, motor stops, mnul override possile Relese utton: Ger engges, synchronistion strts, followed y stndrd mode 5 Service plug For connecting prmeteristion nd service tools Check power supply connection 2 Off nd 3 On Possile wiring error in power supply Service! Notes he ctutor cn e prmeterised y PC-ool nd ZH E vi the service socket. ZH E connection AC 24 V DC 24 V MP SB i esc OK www.elimo.eu SR24A-MF en-g 2015-04-28 suject to chnges 5
Service PC-ool connection AC 24 V DC 24 V MP SB i esc OK BELIMO PC-ool SB Dimensions [mm] Dimensionl drwings 140 86 R 65 93 33 130 43 Further documenttion Overview Vlve-ctutor comintions Dt sheets for ll vlves Instlltion instructions for ctutors nd/or ll vlves Generl notes for project plnning 6 SR24A-MF en-g 2015-04-28 suject to chnges www.elimo.eu