ELEVEN COLLABORATIVE
Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT AND CONNECTION.... 8 TOP ATTACHMENT.... 9
Support Brace Assembly THIS STEP IS NOT USED ON ALL TABLES is to be flipped over after legs are installed. NOTE: Frame is assembled upside-down. Frame NOTE: is to be flipped This over step after is legs used are only installed. on trapezoid tables and some boat-shaped tables. NOTE: This step is used only on trapezoid tables and some boatshaped tables. Position Support Brace so counter-sunk holes in Outside Leg Insert rail are aligned with holes on end of Support Brace. Insert Flat Head Cap Screws and tighten with 5MM allen wrench. Position Support Brace so counter-sunk holes in Outside Leg Insert rail are aligned with holes on end of Support Brace. Outside Leg Rail Insert Flat Head Cap Screws and tighten with 5MM allen wrench. Support Brace Flat Head Cap Screw 3 Completed Assembly
Table Base Frame Assembly THIS STEP IS NOT USED ON ALL TABLES NOTE: Frame is assembled upside-down. Frame is to be flipped over after legs are installed. TABLE BASE FRAME ASSEMBLY (This step is not used on all tables) NOTE: Frame is assembled upside-down. Frame is to be flipped over after legs are installed. Support Rail Clamp Position Double Top Support Rail Position and Single Double Top Top Support Rail and Single Top so counter-sunk holes in Inside Support Leg Insert Rail Rail so counter-sunk are aligned holes with in Inside Leg Insert Rail are aligned with holes on end of Support holes on end of Support Rails. Rails. Insert Flat Head Cap Screws and Insert tighten Flat Head with 5MM Cap Screws allen and tighten with 5MM allen wrench. wrench. Inside Leg Insert Rail, OR Straight Leg Insert Rail Single Top Support Rail Double Top Support Rail Position Support Rail Clamp where indicated & -TIGHTEN SECURELY- Loosen bolts in Support Rail Clamp with 5MM Allen wrench, and postion on Support Rails where indicated Loosen bolts in Support Rail Clamp on the with Assembly 5MM allen Master wrench, Illustration. and position on Support Rails where indicated on the Clamp onto Rails and - SECURELY TIGHTEN - bolts. Assembly Master Illustration. Install required rail on opposite end of rails. Clamp onto Rails and -SECURELY TIGHTEN- bolts. Install required rail on opposite end of rails. Flat Head Cap Screw 4
Leg Attachment wn. Frame led. Loosen bolts first! NOTE: Frame is assembled upside-down. Frame is to be flipped over after legs are installed. USE THIS METHOD FOR: Rectangular Tables 84 and Smaller Trapezoid Tables Square Tables Round Tables Three-legged Tables Use 5MM allen wrench to loosen leg bolts. DO NOT REMOVE BOLTS Slide leg between rails until leg bottoms out, leaving no gap. Tighten bolts. Outside Leg Rails USE THIS METHOD FOR: Rectangular Tables larger than 84 Loosen bolts first! Use 5MM allen wrench to loosen leg bolts. DO NOT REMOVE BOLTS Slide leg between rails until leg bottoms out, leaving no gap. Tighten bolts. On larger tables with 6 legs, center legs are inserted into Straight Leg Rails. Inside Leg Rail 5 Outside Leg Rail
NOTE: Flip assembled frame over to rest on feet at this time.. Top Joining Plate Assembly NOTE: All Top Joining Plates are pre-assembled THIS STEP with IS NOT clamps USED bolted ON ALL in TABLES place. NOTE: Flip assembled frame over to rest on feet at this time. Clip Top Joining Plates to inside faces of Double and Single Support Rails. NOTE: All Top Joining Plates are pre-assembled with clamps bolted in place. Position Plates so they are at the mid-point of the rails. Tighten Clamps with 5MM allen wrench. 120x42 & 120x48 RECTANGULAR TABLES 66 & 72 SQUARE TABLES AND TRAPEZOID TABLES 120 x 42 & 120 x 48 Rectangular Tables, 66 & 72 Square Tables and Trapezoid Tables Clip Top Joining Plates to inside faces of Double and Single Support Rails. Position Plates so they are at the mid-point of the rails. Clip Top Joining Plates to inside faces of Double and Single Support Rails. Tighten Clamps with 5MM allen wrench. Position Plate so it is at the mid-point of the rails. 96x48, 108x48 & 120x48 BOAT-SHAPED TABLES Tighten Clamps with 5MM allen wrench. Clip Top Joining Plates to inside faces of Double and Single Support Rails. Position Plates so it is at the mid-point of the rails. Tighten Clamps with 5MM allen wrench. 96 x 48, 108 x 48 & 120 x 48 Boat-Shaped Tables Clip Top Joining Plates to inside faces of Straight Leg Insert Rails (between the rails). ALL OTHER TABLES WITH 2 PIECE TOPS Slide Plates outward as far as they will go. Clip Top Joining Plates to inside faces of Straight Leg Insert Rails (between the rails). Tighten Clamps with 5MM allen wrench. Slide Plates outward as far as they will go. Tighten Clamps with 5MM allen wrench. All Other Tables with 2 Piece Tops 6
Top Clamp/Top Spacer Installation Snap Top Clamps onto rails where shown on Assembly Master Illustration. Flat surface of Top Clamp faces up. When correctly positioned, tighten Top Clamps (without over-tightening) using 5MM allen wrench. Snap Top Clamps onto rails where shown on Assembly Master Illustration. Flat surface of Top Clamp faces up. When correctly postioned, tighten Top Clamps (without over-tightening) using 5MM allen wrench. TOP Top Clamp Top Spacer Peel off adhesive backers on Top Spacers and adhere one on each leg. Peel off adhesive backers on Top Spacers and adhere one on each leg. 7
Top Placement and Connection Place top on frame. Two piece tops need to be placed so there is access to routes for Joint Fasteners on bottom side of top. Connect two halves of top together using Joint Fasteners in routed-out sections on connecting edges. Tighten with 7/16 wrench. 8
Top Attachment DISTANCE A DISTANCE B DISTANCE B DISTANCE A Position top so it is centered on the base. Use two #8 x 1 truss head screws per Top Clamp to secure top to base. If needed, use the same screws to fasten Top Joining Plate to top. 9 11.16