Sunnen Portable Hones

Sunnen Portable Hones For Bore Diameters 4,70.185" 0" Fast and efficient for all kds of bore-sizg work. Corrects undersize, taper, out-of-round, barrel or bellmouth shape and misalignment to tolerances of,01 (.0005") diameters from 1,8-914 (1.250"-"). Larger sizes up to (0") available on special order. Ideal for hong parts too big or awkward to brg to a mache tool. *Refer to pages 1-17 for portable toolg to hone diameters from 4,7-1,75 (.185 "- 1.250") What will Sunnen Portable Hones do for you? Repair production equipment on the spot with mimum delay Repair worn or scuffed air and hydraulic cylders Resize beargs Recondition compressors, enges, pumps Pull tandem holes to le Repair hydraulic valves Remove tool marks from cylders Hone I.D. s for fit durg mache assembly Clean up assembly or heat-treat distortion Correct I.D. errors reject parts Sunnen Portable Hones are capable of hong open, shouldered, bld, keyway, spled, tandem, or rifled bores to a uniform surface fish of.08-1.5 micrometer Ra (-0 microches Ra) alumum, welded, drawn or hardened steel, brass, ceramic, carbide, etc. They can be run an electric drill, air drill, drill press, or hong rig. How to select the Power Source for your Sunnen Portable Hone. Sunnen Portable Hones may be driven by a heavyduty electric drill, air drill, or drill press. Optimum RPM is calculated by dividg 00 by the bore diameter ches... for example: 00 ches = 200 RPM; or dividg 0,000 by the bore diameter millimeters... for example 0,000 0 millimeters = 200 RPM. If the power source is a drill press or other rigid strokg device, make sure your portable hone is equipped with two universal jots to provide full floatg action at the hong head. Remote feed hones should always be used a rig, either horizontally or vertically. Choose the Proper Portable Hone for Your Application from pages 2-144. 1

SNJ-10 Portable Hone Hand Feed 1,8 45 1,250" 1.770" SNJ-10 Portable Hone assembled with Stone Set and AN-2A Drive Shank. Will hone bores up to 457 (18") long as shown; order additional Shaft Extensions for longer bores Requires 1 (1/2") chuck capacity. Shippg weight:,5kg (1lb.) How To Order Specify SNJ-10 Basic Hone (cludes 7 (") Drive Shank and one Universal Jot). Additional Shaft Extensions may be ordered from table below to make up any practical length. Drive Shank can be used with any combation of Extensions. See Stone Sets Table below. Drive Shanks Shaft Extensions 7 AN-2A* 05 10 20 * Supplied with hone AN-1* AN-2 AN-4 2 PHT Plateau Hong Tools Sunnen s PHT tools are used as a fal fishg step, after itial hong to provide a plateau surface on cylder walls. Made from special abrasive impregnated filament. For additional formation contact your local Sunnen Field Engeer or call Customer Service toll-free St. Louis For Diameter Range Abrasive Sets (20 Grit) 8,1-42,9 42,4-47,2 44,4-49,,5-5, 52,8-57, 1.50-1.9 1.7-1.8 1.75-1.94 1.91-2.10 2.08-2.27 Accessories AN-70 Universal Jot AN-80 Quick Coupler See page 4 SNJ1-PHT-72 SNJ2-PHT-72 SNJ-PHT-72 SNJ4-PHT-72 SNJ5-PHT-72 In some cases, stones other than the RECOM- MENDED STONES above may hone faster or last longer. For long or repetitive production runs, it may be economical to choose a stone slightly harder or softer, coarser or fer. If the stone wears out too fast, use a harder stone; if it does not cut, use a softer stone. *1st choice **2nd choice. Use if A45 does not cut. } ***rd choice. Use if A4 does not cut. All Available Stones** Grit Size 0 0 280 400 Recoended Stones Sets Material Deburrg: rough holes, all materials SNJ1-A47 SNJ2-A47 SNJ-A47 Fast removal: deburred, bored, ground, reamed holes Alumum, Bronze Brass, Soft Carbide Cast Iron Ceramic, Glass Steel, Soft Steel, Hardened* Steel, Hardened** Steel, Very Hard*** Alumum, Bronze Brass, Soft Carbide Cast Iron Ceramic, Glass Steel, Soft 1,75-,50 1.250"-1.47" SNJ1-A4 SNJ1-A45 SNJ1-A47 SNJ1-J45 SNJ1-J SNJ1-J85 SNJ1-J87 1,75-,50 1.250"-1.47" SNJ1-J45 SNJ1-J SNJ1-J45 SNJ1-A45 SNJ1-A45 SNJ1-A4 SNJ1-J Fe fishg: previously honed holes SNJ1-J87 SNJ1-J85 SNJ1-J87 SNJ1-J87 SNJ1-J85,02-40,74 1.418"-1.04" Alumum Oxide SNJ2-A4 SNJ2-A45 SNJ2-A47 Silicon Carbide SNJ2-J45 SNJ2-J SNJ2-J85 SNJ2-J87 Additional stones available 2 weeks after receipt of order. Stone Sets* (Consists of Stones) For General Purpose Hong,02-40,74 1.418"-1.04" SNJ2-J45 SNJ2-J SNJ2-J45 SNJ2-A45 SNJ2-A45 SNJ2-A4 SNJ2-J SNJ2-J87 SNJ2-J85 SNJ2-J87 SNJ2-J87 SNJ2-J85 40,1-45,00 1.580"-1.770" SNJ-A4 SNJ-A45 SNJ-A47 SNJ-J45 SNJ-J SNJ-J85 SNJ-J87 40,1-45,00 1.580"-1.770" SNJ-J45 SNJ-J SNJ-J45 SNJ-A45 SNJ-A45 SNJ-A4 SNJ-J SNJ-J87 SNJ-J85 SNJ-J87 SNJ-J87 SNJ-J85 Approximate Ra Surface Fish µm µ 2,00 0,8 0,80 0,88 0,50 0,50 0,0 0,8 0,8 0, 0,18 0,1 ** Call Sunnen Products Customer Service Department for recoendations on hong carbide, ceramic or glass. 80 2 5 20 20 7 5

SN-75 Portable Hone Hand Feed How To Order Specify SN-75 Basic Hone (cludes 7 (") Drive Shank, 05 (") Extension and one Universal Jot). Additional Shaft Extensions may be ordered from table below to make up any practical length. Drive Shank can be used with any combation of Extensions. See Stone Sets Table on Page 4. Drive Shanks Shaft Extensions 44 51 1.750" 2" SN-75 Portable Hone assembled with Stone Set, Drive Shank, and 05 (") Shaft Extension. 102 (4") stone length. Will hone bores up to 5 (21") long as shown; order additional Shaft Extensions for longer bores. Requires 1 (1/2") chuck capacity. Shippg weight: 1,4kg ( lb.) 7 AN-2A* 05 10 20 * Supplied with hone SNR-185 Portable Hone Remote-Feed Midget Hone AN-1* AN-2 AN-4 How To Order Specify SN-185 Remote-Feed Midget Hone (cludes 7 (") Drive Shank; and two Universal Jots). Shaft Extensions listed table below may be used alone or combed to make up any practical length. Shaft Extensions are stalled between Remote-Feed Unit and Hone Head Assembly. See Stone Sets Table on Page 4. Larger diameters from 51- (2.0"- 2.") can be honed by changg to larger Hone Head Assembly. To order, specify JNR-85 Hone Head Assembly. 44 51 1.750" 2" SNR-185 Remote-Feed Midget Hone as supplied, except for Stone Set, which must be ordered separately. Will hone bore lengths up to 279 (11") as shown. Additional Shaft Extensions available for hong longer bores. Requires 1 (1/2") chuck capacity. Shippg weight:,kg (8 lbs.) Drive Shanks Shaft Extensions 7 * Supplied with hone. AN-2A* 05 10 914 19 1829 0 72 JNR-441 JNR-442 JNR-44 JNR-444 JNR-445 JNR-44

SN-75/SNR-185 Accessories and Stone Sets Accessories AN-70 Universal Jot Order an additional Universal Jot when usg the SN-75 a drill press or other rigid strokg device. Use place of Drive Shank AN-2A Shippg weight:,4kg (.75 lb.) AN-80 Quick Coupler AN-87 Replacement Yoke Adapter AN-79A Replacement Coupler Sleeve In some cases, stones other than the RECOM- MENDED STONES above may hone faster or last longer. For long or repetitive production runs, it may be economical to choose a stone slightly harder or softer, coarser or fer. If the stone wears out too fast, use a harder stone; if it does not cut, use a softer stone. ** Call Sunnen Products Customer Service Department for recoendations on hong carbide, ceramic or glass. *1st choice **2nd choice. Use if A45 does not cut. } ***rd choice. Use if A4 does not cut. Recoended Stones Sets Material Deburrg: rough holes, all materials S18-A47 Fast removal: deburred, bored, ground, reamed holes Alumum, Bronze S18-J45 2,00 80 Brass, Soft S18-J 0,8 Carbide Cast Iron S18-J45 0,80 2 Ceramic, Glass Steel, Soft S18-A45 0,88 5 Steel, Hardened* S18-J45 0,50 20 Steel, Hardened** S18-J4 0,50 20 Steel, Very Hard*** S18-J 0,0 Fe fishg: previously honed holes Alumum, Bronze Brass, Soft Carbide Cast Iron Ceramic, Glass Steel, Soft Steel, Hardened Stone Sets* (2 Stones & 2 Guides) For General Purpose Hong S18-J87 S18-J85 S18-J87 S18-J87 S18-J85 Approximate Ra Surface Fish µm µ 0,8 0,8 0, 0,18 0,1 7 5 Provides stant couplg or uncouplg of hone from drive motor. Install between Drive Shank and Shaft Extension, or between Drive Shank and Hone Head on short bores. Shippg weight:,45kg (1 lb.) PHT Plateau Hong Tools For SN/SNR Hone Sunnen s PHT tools are used as a fal fishg step, after itial hong to provide a plateau surface on cylder walls. Made from special abrasive impregnated filament. For additional formation contact your local Sunnen Field Engeer or call Customer Service toll-free St. Louis For Diameter Range Abrasive Sets (20 Grit) 54,-0,9 2.-2.40 SN-PHT-72 Hard------Soft Hard--Soft Available Stones Grit Size 70 80 0 220 280 400 500 00 (S18-J11) S18-J1 S18-J S18-J17 (S18-J19) (S18-A2) (S18-A25) Alumum Oxide (S18-A41) (S18-A55) S18--A S18-A4 S18-A5 S18-A45 (S18-A57) S18-A7 S18-A47 (S18-A) S18-A49 S18-J4 S18-J45 S18-J47 S18-J49 Silicon Carbide (S18-J55) S18-J S18-J8 S18-J5 S18-J85 S18-J7 S18-J87 S18-J9 (S18-J57) Stones parentheses available 2 weeks after receipt of order. S18-J95 (S18-J97) (S18-CO5) Superabrasive Stone Sets for Portable Hones Metal Bond Diamond and Borazon/CBN Stone Sets Use to crease stock removal rates or abrasive life when compared to A or J stones, res or vitrified diamond and Borazon/CBN stones. First time users of metal bond superabrasive stone sets must order S18-KV1X Master Holder Set. Replacement stone can be ordered without reorderg KV1X Master Holders. 4 Master Holder Stone Set Diameter Range S18-KV1X S18- XG94 44-51 1.75-2.00 The the stone set number is for the metal bond abrasive code. This set consists of two L superabrasive stones and two roughg guides. Select the L metal bond superabrasive stone desired from the stone selection guide found on page 9. Master Holders available 4 weeks after receipt of order. Stone sets available 1 week after receipt of order. Diamond and Res Borazon/CBN Sets For hong carbide, ceramic, glass and hardened steel. Available 82.55 (-1/4") or 101. (4") stone length. For 82.55 (-1/4") length add -85 to stone number. Diamond Stone DV-47 DV-57 DV-87 DV-07 Borazon Stone NR5 Res Bond NR8 Res Bond Ex: S18-NR5 Available 1-2 weeks after receipt of order.

JN-95 Portable Hone Hand Feed How To Order Specify JN-95 Basic Hone (cludes 7 (") Drive Shank, 05 (") Extension, and one Universal Jot). Additional Shaft Extensions may be ordered from table below to make up any practical length. Drive Shank can be used with any combation of Extensions. See Stone Sets Table on Page. 51 2" 2.00" JN-95 Portable Hone assembled with Stone Set, Drive Shank, and 05 (") Shaft Extension. 102 (4") stone length. Will hone bores up to 5 (21") long as shown; order additional Shaft Extensions for longer bores. Requires 1 (1/2") chuck capacity. Shippg weight: 1,4kg ( lbs.) Drive Shanks Shaft Extensions 7 AN-2A* 05 10 20 * Supplied with hone AN-1* AN-2 AN-4 How To Order Specify JNR-210 Remote -Feed Junior Hone. Shaft Extensions listed table below may be used alone or combed to make up any practical length. Shaft Extensions are stalled between Remote-Feed Unit and Hone Head Assembly. See Stone Sets Table on Page. Smaller diameters from 44-51 (1.750"-2") can be honed by changg to smaller Hone Head Assembly. To order, specify SNR-80 Hone Head Assembly. Drive Shanks Shaft Extensions JNR-210 Remote-Feed-Junior Hone 51 2" 2.00" JNR-210 Remote-Feed Junior Hone as supplied, except for Stone Set, which must be ordered separately. Will hone bore lengths up to 05 (") as shown. Additional Shaft Extensions available for hong longer bores. Requires 1 (1/2") chuck capacity. Shippg weight:,kg (8.5 lbs.) 7 *Supplied with hone. AN-2A* 05 10 914 19 1829 0 72 JNR-441 JNR-442 JNR-44 JNR-444 JNR-445 JNR-44 5

JN-95/JNR-210 Accessories and Stone Sets PHT Plateau Hong Tools For JN/JNR Hone Sunnen s PHT tools are used as a fal fishg step, after itial hong to provide a plateau surface on cylder walls. Made from special abrasive impregnated filament. For additional formation contact your local Sunnen Field Engeer or call Customer Service toll-free St. Louis For Diameter Range 0,9-,0 8,0-71,1 71,1-7,2 Accessories AN-70 Universal Jot Order an additional Universal Jot when usg the JN-95 a drill press or other rigid strokg device. Use place of Drive Shank AN-2A Shippg weight:,4kg (.75 lb.) AN-80 Quick Coupler AN-87 Replacement Yoke Adapter 2.40-2.0 2.0-2.80 2.80-.00 AN-79A Replacement Coupler Sleeve Provides stant couplg or uncouplg of hone from drive motor. Install between Drive Shank and Shaft Extension, or between Drive Shank and Hone Head on short bores. Shippg weight:,45kg (1 lb.) Abrasive Sets (20 Grit) JN0-PHT-72 JN1-PHT-71 JN2-PHT-71 * In some cases, stones other than those recoended above may hone faster or last longer. For long or repetitive production runs, it may be economical to choose a stone slightly harder or softer, coarser or fer. If the stone wears out too fast, use a harder stone; if it does not cut, use a softer stone. ** Call Sunnen Products Customer Service Department for recoendations on hong carbide, ceramic or glass. Alumum Oxide Silicon Carbide Available Stones H----S H-------S H-------S H-----S H-------S Hard--Soft H----S H----S Hard----Soft H----S Grit Size (T20-A2) 80 T20-A25 (T20-A27) (T20-A41) T20-A4 0 T20-A45 T20-A47 (T20-A) (T20-A49) (T20-A55) 220 (T20-A57) (T20-A59) T20-A 280 T20-A5 T20-A7 20 (T20-A79) 70 0 220 280 400 500 00 T20-J11 T20-J1 T20-J T20-J17 (T20-J19) T20-J4 T20-J45 T20-J47 T20-J49 (T20-J55) (T20-J57) (T20-J59) T20-J T20-J5 T20-J7 T20-J8 T20-J85 T20-J87 (T20-J89) (T20-J9) T20-J95 (T20-J97) (T20-CO5) (U22-A2) U22-A25 (U22-A27) (U22-A41) U22-A4 U22-A45 U22-A47 (U22-A) U22-A49 (U22-A55) U22-A U22-A5 U22-A7 (U22-J11) U22-J1 U22-J U22-J17 (U22-J19) U22-J4 U22-J45 U22-J47 (U22-J49) (U22-J55) U22-J U22-J5 U22-J7 (U22-J9) U22-J8 U22-J85 U22-J87 (V-A2) V-A25 (V-A27) (V-A41) V-A4 V-A45 V-A47 (V-A) (V-A49) (V-A55) V-A V-A5 V-A7 (V-J11) V-J1 V-J V-J17 (V-J19) V-J4 V-J45 V-J47 (V-J49) (V-J55) V-J V-J5 V-J7 (V-J9) V-J8 V-J85 V-J87 Stones parentheses available 2 weeks after receipt of order. Recoended Stones Sets Alumum, Bronze Brass, Soft Carbide** Cast Iron Ceramic, Glass** Steel, Soft Steel, Hardened Steel, Hardened Steel, Very Hard Alumum, Bronze Brass, Soft Carbide** Cast Iron Ceramic, Glass** Steel, Soft Steel, Hardened (U22-J9) U22-J95 (U22-J97) U22-CO5 Stone Sets*(2 Stones and 2 Guides) For General Purpose Hong 51-5 5-1 1- Material 2"-2.2" 2.2"-2.4" 2.4"-2." µm µ Deburrg: rough holes, all materials T20-A47 U22-A47 V-A47 Fast removal: deburred, bored, ground, reamed holes T20-J45 T20-J T20-J45 T20-A45 T20-A45 T20-A4 T20-J T20-J87 T20-J85 T20-J87 T20-J87 T20-J85 (V-J9) (V-J95) (V-J97) (V-CO5) U22-J45 U22-J U22-J45 U22-A45 U22-A45 U22-A4 U22-J U22-J87 U22-J85 U22-J87 U22-J87 U22-J85 V-J45 V-J V-J45 V-A45 V-A45 V-A4 V-J Fe fishg: previously honed holes V-J87 V-J85 V-J87 V-J87 V-J85 Approximate Ra Surface Fish 2,00 0,8 0,80 0,88 0,50 0,50 0,0 0,8 0,8 0, 0,18 0,1 80 2 5 20 20 7 5

Metal Bond Diamond and Borazon/CBN Stone Sets Use to crease stock removal rates or abrasive life when compared to A or J stones, res or vitrified diamond and Borazon/CBN stones. First time users of metal bond superabrasive stone sets must order S18-KV1X Master Holder Set. Replacement stone can be ordered without reorderg KV1X Master Holders. Superabrasive Stone Sets Repair s Superabrasive Stone Sets for Portable Hones Master Holder Stone Set Diameter Range ches T20-KV1X T20- XG94 51-5 2.0-2.2 U22-KV1X U22- XG94 5-1 2.2-2.4 V-KV1X V- XG94 1-2.4-2. Diamond and Res Borazon/CBN Sets For hong carbide, ceramic, glass and hardened steel. Available 82.55 ( 1/4") or 101. (4") stone length. For 82.55 ( 1/4") length add -85 to stone number. The the stone set number is for Diamond Stone Borazon Stone the metal bond abrasive code. This set DV-47 NR5 Res Bond consists of two L1 superabrasive stones and two roughg guides. DV-57 NR8 Res Bond Select the L1 metal bond superabrasive stone desired from the stone DV-07 DV-87 selection guide found on page 9. Ex: T20-NR5 Master Holders available 4 weeks after Available 1-2 weeks after receipt of order. receipt of order. Stone sets available 1 week after receipt of order. Portable Hones and Accessories SN-75 Portable Hone SN-95 Portable Hone SN-11 JN-0 JN-2A JN-11 JN-0 JN-2A SN-11 Hone Body JN-11 Hone Body JN-0 Universal Jot Complete JN-0 Universal Jot Complete JN-2A Adjustg Nut and Washer JN-2A Adjustg Nut and Washer AN-1 Portable Hones AN-8 Portable Hone AN-4 AN-A AN-50 AN-1 AN-04 AN-A AN-50 AN-1 AN-4 AN-50 AN1 AN-A Hone Body Universal Jot Complete Center Pion Adjustment Body Gear AN-50 AN-04 AN-1 AN-A Hone Body Universal Jot Complete Adjustg Nut and Washer Body Gear Set 7

AN-1 Portable Hone Hand Feed For Occasional Light-Duty Portable Hong 4 178 2.5" 7" AN-1 Portable Hone assembled with Stone Set, 7 (") Drive Shank and 05 (") Shaft Extension. 102 (4") stone length. Requires 1 (1/2") chuck capacity. Shippg weight: 1,8kg (4 lbs.) Diameter Range 4-178 2.5" -7" General Purpose Stone Sets 4-140 104-10 119-178 2.5-5.5 4.1-. 4.7-7.0 Guideless and Keyway Stone Sets 4-142 114-10-18 Order 1-5 For Complete AN-1 Portable Hone 1 Basic 2 Master Hone Holder Sets Sgle Double Length Length 2.5-5. 4.5-.5 5.1-7.2 AN-1 AN-1 AN-1 AN-45 AN-55 AN-855 Stone 4 Stone Support Set See tables on page for portable hone stone sets. 5 Shaft Extension For holes longer than 508 (20") see table below for shaft extensions. Drive Shanks Shaft Extensions Accessories 7 AN-2A 05 10 20 AN-1* AN-2 AN-4 * Furnished with 7 (") Drive Shank and 05 (") Shaft Extension. Other shanks or extensions may be selected from the table above to make up any practical length (either drive shank can be used with any combation of extensions). Master Holder Sets Stone Stones AN-70 Universal Jot Order an additional Universal Jot when usg the AN-1 a drill press or other rigid strokg device. Use place of Drive Shank. Shippg weight:,4kg (.75 lb.) AN-80 Quick Coupler AN-87 Replacement Yoke Adapter AN-79A Replacement Coupler Sleeve Sgle Length Master Holder Double Length Master Holder Master Holder Sets, listed the table above, are used with Type W47, WW51, and WY51 Stone Sets. Double Length Master Holders require two stone sets use when it is necessary to bridge terruptions the bore. Each Master Holder Set consists of two holders for stones and two holders for guides. Provides stant couplg or uncouplg of hone from drive motor. Shippg weight:,45kg. (1 lb.) 8

AN-8 Portable Hone Hand Feed For Occasional Heavy-Duty Portable Hong 4 5 2.5" 21" AN-8 Portable Hone assembled with sgle length master holder set and stone set. Requires 1 (5/8") chuck capacity for,5-7 (2.5"-5") diameter. Requires 19 (/4") chuck capacity for 7-81 (5"-") diameter. Requires 25,4 (1") chuck capacity for larger than 81 (") diameter. Shippg weight: 2,kg (5 lbs.) Diameter Range 4-5 2.5" -21" General Purpose Stone Sets 4-140 104-10 119-178 2-229 20-05 279-81 5-457 42-5 2.5-5.5 4.1-. 4.7-7.0.0-9.0 8.1-.0 11.0-.0 14.0-18.0 17.0-21.0 Guideless and Keyway Stone Sets 4-142 114-10-18 1-21-10** 284-8** -45** 47-58** Order 1-5 For Complete AN-8 Portable Hone 1 Basic 2 Master Hone Holder Sets Sgle Double Length Length 2.5-5. 4.5-.5 5.1-7.2.4-9.2 8.4-.2** 11.2-.2** 14.-18.** 17.2-21.2** AN-8 AN-8 AN-8 AN-8 AN-8 AN-8 AN-8* AN-8* AN-45 AN-55 AN-5 AN-75 AN-85 AN-95 AN-4 AN-855 AN-85 AN-875 AN-885 AN-895 AN-9 * For light work only this diameter range. For heavy-duty or production work see pages 10 or 11. ** Do not use WW (Guideless) Stone Sets this range due to lack of stability. Stone 4 Stone Support Set AN-20 AN-280 AN-290 AN-40 AN-450 See tables on page for portable hone stone sets. 5 Shaft Extension For holes longer than 508 (20") see table below for Shaft Extensions. Drive Shanks Shaft Extensions Accessories 7 2 Suppled with hone. AN-08A AN-18A 2 05 10 20 AN-840 AN-841 AN-842 AN-844 * Furnished with 7 (") Drive Shank and 05 (") Shaft Extension. Other shanks or extensions may be selected from the table above to make up any practical length (either drive shank can be used with any combation of extensions). Sgle Length Master Holder Master Holder Sets Stone Stones Stone Support Double Length Master Holder Master Holder Sets, listed the table above, are used with Type W47, WW51 and WY51 Stone Sets. Double Length Master Holders require two stone sets use when it is necessary to bridge terruptions the bore. Each Master Holder Set consists of two holders for stones and two holders for guides. Stone Supports are required to give rigidity to the hone assembly when hong bores larger than 178 (7") diameter. AN-70 Universal Jot Order an additional Universal Jot when usg the AN-8 a drill press or other rigid strokg device. Shippg weight:,7kg (1.5 lb.) AN-85 Quick Coupler Provides stant couplg or uncouplg of hone from drive motor. Shippg weight:,45kg (1 lb.) AN-97 Replacement Yoke Adapter AN-89A Replacement Coupler Sleeve 9

ANR-275 Wide Range Hone Remote Feed For Heavy-Duty Production Hong to be used a mache or hong rig 4 5 2.5" 21" ANR-275 Portable Hone assembled with Stone Support, Sgle Length Master Holder Set, Stone Set and 7 (") Drive Shank. 102 (4") stone length (20 [8"] when two sets of stones are used with Double Length Master Holder Set.) Requires 1 (5/8") chuck capacity for,5-7 (2.5"-5") diameter. Requires 19 (/4") chuck capacity for 7-81 (5"-") diameter. Requires 25,4 (1") chuck capacity for larger than 81 (") diameter. Shippg weight: 5,2 kg (11.5 lbs.) Diameter Range 4-5 2.5" -21" General Purpose Stone Sets 4-140 104-10 119-178 2-229 20-05 279-81 5-457 42-5 2.5-5.5 4.1-. 4.7-7.0.0-9.0 8.1-.0 11.0-.0 14.0-18.0 17.0-21.0 4-142 114-10-18 1-21-10** 284-8** -45** 47-58** Order 1-5 For Complete ANR-275 Portable Hone 1 Basic 2 Master Hone Holder Sets Sgle Double Length Length Guideless and Keyway Stone Sets 2.5-5. 4.5-.5 5.1-7.2.4-9.2 8.4-.2** 11.2-.2** 14.-18.** 17.2-21.2** ANR-275 ANR-275 ANR-275 ANR-275 ANR-275 ANR-275 ANR-275* ANR-275* AN-45 AN-55 AN-5 AN-75 AN-85 AN-95 AN-4 AN-855 AN-85 AN-875 AN-885 AN-895 AN-9 * For light work only this diameter range. For heavy-duty or production work see pages 10 or 11. ** Do not use WW (Guideless) Stone Sets this range due to lack of stability. Stone 4 Stone Support Set AN-20 AN-280 AN-290 AN-40 AN-450 See tables on page for portable hone stone sets. 5 Shaft Extension For holes longer than 229 (29") see table below for Shaft Extensions. Drive Shanks Shaft Extensions Accessories 7 2 AN-08A* AN-18A 25 108 185 9.25 19.00 42.75 72.25 ANR-741* ANR-742 ANR-744 ANR-74 * Furnished with 7 (") Drive Shank ANR. Other shanks or extensions may be selected from the table above to make up any practical length (either drive shank can be used with any combation of extensions). Master Holder Sets Stone Stones Stone Support AN-85 Quick Coupler Provides stant couplg or uncouplg of hone from drive motor. Shippg weight:,45kg (1 lb.) AN-97 Replacement Yoke Adapter AN-89A Replacement Coupler Sleeve 10 Sgle Length Master Holder Double Length Master Holder Master Holder Sets, listed the table above, are used with Type W47, WW51, and WY51 Stone Sets. Double Length Master Holders require two stone sets use when it is necessary to bridge terruptions the bore. Each Master Holder Set consists of two holders for stones and two holders for guides. Stone Supports are required to give rigidity to the hone assembly when hong bores larger than 178 (7") diameter.

GNH Giant Portable Hone Hand Feed For large diameter or heavy-duty hong above 254 (10") 254 10" 0" GNH-10 Hand-Feed Giant Hone assembled with hong stones and drive shank. Order additional shaft extensions for longer bores. All giant hones require 2 sets of W47 or WY51 stones to load the hone. (See Tables on page 14 for Stone sets for GNH Hones.) Drive Source Drive motors of 2.2-.7KW ( to 5 HP) provide adequate torque to turn the hone. These hones may be driven by a rigidly mounted power source such as a radial drill press or a large lathe; 29 (1-1/8") chuck capacity is required. A second universal jot, AN-970, is needed between the mache spdle and the drive shaft to allow for full floatg action of the head. To Order: Select the correct Giant Hone, drive shaft extension (for bore length 04 ["] or longer and universal jot, if needed). Hand-Feed Giant Hones Diameter Range ches 254-81 81-508 508-711 711-914 914-1118 1118-121 121-10- -20 20-28 28- -44 44-52 52-0 Shippg Weight kg lbs. GNH-1010 GNH-10 GNH-2010 GNH-2810 GNH-10 GNH-4410 GNH-5210 Call Customer Service for weight formation. 8,2 19 1 1 18 42 8 2 05 10 9 20 180 Drive Shaft Extensions 0 72 GNH- GNH- GNH- GNH- GNH- GNH-0 GNH-72 Remote Feed Conversion for hand-feed hones: Hand-Feed Giant Portable Hones may be converted to remote feed operation by orderg the followg: GNR-920 Remote-Feed Drive Unit ANR-210A Pion Adjustment Assembly Drive Shaft Extensions for Remote Feed Hones are listed at right. Recoended RPM:To establish optimum RPM for your application, divide 00 by bore diameter ches. EX: 00 10=0(RPM). Or, divide 000 by bore diameter. EX: 0000 254=118(RPM). Available 4 weeks after receipt or order. 11

GNR Giant Portable Hone For large diameter work on deep bores, production hong, or parts with limited access for stone adjustment diameters larger than 254 (10") 254 10" 0" Additional Hone Heads Extend the Diameter Range GNR-1010 Remote-Feed Giant Hone assembled with hong stones. Will hone bores up to 04 (") long as shown. Order additional drive shafts for longer bores. All giant hones require 2 sets of W47 or WY51 stones to load the hone. (See Tables on page 14 for Stone sets for GNR Hones.) The remote feed permits the operator to expand the stones at any time while the hong head is runng the bore, as well as when the hone is stopped. The operator controls the amount of stone expansion and the hong pressure by brakg the feed wheel while the hone is turng. The remote feed also permits the operator to quickly retract the stones and remove the hone from the bore when the hone is stopped. Drive Source Drive motors of 2.2-.7KW ( to 5 HP) provide adequate torque to turn the hone. These hones may be driven by a rigidly mounted power source such as a radial drill press or a large lathe; 29 (1-1/8") chuck capacity is required. Remote-Feed Giant Hones are equipped with two universal jots which allow the hong head to align itself with the workpiece. Recoended RPM: To establish optimum RPM for your application, divide 00 by bore diameter ches. EX: 00 10=0 (RPM). Or, divide 000 by bore diameter. EX: 000 254=118 (RPM). To Order: Select the correct Giant Hone, drive shaft extension (for bore length 04 ["] or longer and universal jot, if needed). 12 Remote-Feed Giant Hones Diameter Range 254-81 81-508 508-711 711-914 914-1118 1118-121 121-10- -20 20-28 28- -44 44-52 52-0 Shippg Weight kg lbs. GNR-1010 GNR-10 GNR-2010 GNR-2810 GNR-10* GNR-4410* GNR-5210* 1,2,7 2,5 8,4 29.5 4.5 58.5 84.5 * Available from stock, except for GNR-10, GNR-4410, and GNR-5210 which can be shipped four weeks after receipt of order. Call Customer Service for weight formation. A complete Remote-Feed Giant Hone consists of a GNR- 920 Remote-Feed Giant Drive Unit and a Giant Hone Head, as illustrated. The GNR-920 Remote-Feed Giant Drive Unit can be used with other Giant Hone Heads to extend the diameter range. Select additional Hone Heads as needed from the table below. Giant Hone Head Additional Hone Heads Diameter to be Honed ches 254-81 81-508 508-711 711-914 914-1118 1118-121 121-10- -20 20-28 28- -44 44-52 52-0 for Shippg Weight Giant Hone Head** kg lbs. GNR-1025 GNR-25 GNR-2025 GNR-2825 GNR-25* GNR-4425* GNR-5225* 4,1,4 17, 29,1 9 14 8 4 *Available from stock, except for GNR-25, GNR-4425, and GNR-5225 which can be shipped four weeks after receipt of order. ** These Hone Heads can be converted to complete Giant Hones at any time by purchasg GNR-920 Remote-Feed Giant Drive Unit. Call Customer Service for weight formation. GNR-920 Weight: 9,kg (20.5 lbs.) Drive Shaft Extensions Giant Hones will handle bore lengths up to 05 (") without Drive Shaft Extensions. When Extensions are necessary, they can be used one at a time or multiples, makg it possible to hone practically any bore length. All Drive Shaft Extensions are stalled between the hone head and the feed wheel as illustrated above. The feed wheel remas outside the bore beg honed, accessible for stone expansion. Drive Shaft Extensions Extension Length 2 05 10 9 20 25 180 0 72 GNR-920 Remote-Feed Giant Drive Unit Shippg Weight kg lbs. GNR-940 GNR-941 GNR-942 GNR-94 GNR-944 GNR-945 GNR-94 1,4 2,4 4,8,4 8,2 9, 10, 5 10.5 14 18 21 2.25

Piloted Portable Hones Use to hone one bore le with another bore on the same axis. Three models cover the diameter range of 44,5-5,4 (1.75"-21"). AN-8-A40X Piloted Portable Hone Diameter Range:.5-5.4 (2.50"-21") The SN-75-887X and JN-95-887X Piloted Portable Hones are furnished with a 25,4 (1") diameter pilot bar. The AN-8- A40X is furnished with a 8,1 (1-1/2") diameter pilot bar. The pilot bar must be long enough so that it will not stroke out of the pilot bushg durg the hong operation. BE SURE TO SPECIFY PILOT LENGTH BAR on your order. The pilot bushg is made by the user. It must be made to fit the bore before and after hong. The bushg O.D. should be tapered to fit the bore opposite the bore beg honed. The bushg l.d. should be,025 (.001") larger than the diameter of the pilot on the hone. The hone is used first one bore with the pilot bushg positioned the other bore. When this bore is fished, the pilot bushg is placed the honed bore and the hone is entered from the other side to fish the second bore. Both outside ends of the tandem bores must be accessible. SN-75-887X Piloted Portable Hone, 44,5-50,8 (1.75"- 2.00") diameter range, cludes 7,0 (") drive shaft, 04,8 (") shaft extension, and 25,4 (1") diameter pilot bar up to 10 (") long (does not clude stone sets). JN-95-887X Piloted Portable Hone, 50,8-0,0 (2.00-2.0") diameter range, cludes 7,0 (") drive shaft, 04,8 (") shaft extension, and 25,4 (1") diameter pilot bar up to 10 (") long (does not clude stone sets). Extra length 25,4 (1") diameter pilot bar for SN-75-887X or JN-95-887X hones will be supplied at an added price per foot or portion thereof, over the 10 (") furnished with the hone. AN-8-A40X Piloted Portable Hone,,5-5,4 (2.50"-21.00") diameter range for light duty use diameters larger than 81 ("), cludes 2,4 (") drive shaft, 04,8 (") shaft extension, and 8,1 (1.5") diameter pilot bar up to 10 (") long (does not clude stone sets, stone supports or master holder sets). Extra length 8,1 (1.5") diameter pilot bar for AN-8- A40X hone will be supplied at an added price per foot or portion thereof, over the 10 (") furnished with the hone. The SN-75-887X Piloted Portable Hone uses the same S18 stone sets as the SN-75 Portable Hone. The JN-95-887X Piloted Portable Hone uses the same T20, U22 or V stone sets as the JN-95 Portable Hone. See page 4 for stone selection. Stone sets, stone supports and master holder sets used with the AN-8-A40X Piloted Portable Hone are found on page 9. These hones may be driven by a heavy duty electric or air drill, or used a drill press. To establish optimum rpm for your application, divide 00 by the hole diameter ches. Example: 00 "= 200 (RPM). Or, divide 0000 by bore diameter. Example: 0000 0 = 200 (RPM). 44,45-7,0 7,0-81,0 81,0 and up Hole Size 1.75-5 5- and up Recoended Drill Check Size,8 19,0 25,4 5/8 /4 1 A universal jot is built to each of these piloted portable hones. A second universal jot is required when the drivg power is obtaed from a drill press, or other rigid strokg device to provide the necessary full floatg action at the hong head as shown below: For Piloted Portable Hone SN-75-887X JN-95-887X AN-8-A40X Order Additional Universal Jot AN-70 AN-70 AN-70 (Heavy-Duty) Shipment:The AN-8-A40X with 10 (") pilot bar is available from stock. SN-75-887X and JN-95-887X can be shipped approximately four weeks after receipt of an order. All Piloted Portable Hones are furnished with a 10 (") pilot bar. Other length pilot bars are available for shipment approximately 4 weeks after receipt of an order. SN-75-887X Shippg Weight: 2,8 kg. ( lbs.) JN-95-887X Shippg Weight: 2,8 kg. ( lbs.) AN-8-A40X Shippg Weight: 4, kg. (10 lbs.) 1

Recoended Stones For Holes Without Keyways For Holes With Keyways Hole Diameters Alumum Brass, Soft Bronze Carbide Cast Iron Ceramic Glass Steel, Soft Steel, Hardened* Steel, Very Hard** Alumum, Brass, Soft Bronze Carbide Cast Iron Ceramic Glass Steel, Soft Steel, Hardened General Purpose Stone Sets (2 Stones and 2 Guides) 4 to 9 (2.5"-2.7") Deburrg: rough holes, all materials G25-A47 M27-A47 N7-A47 W47-A47 GG25-A47 MM-A47 NN40-A47 WW51-A47 GY25-A47 MY-A47 NY40-A47 WY51-A47 Fast removal: deburred, bored, ground, reamed holes G25-J45 G25-J G25-J45 G25-DV47 G25-J45 G25-DV57 G25-DV57 G25-A45 G25-A4 G25-NR5 G25-J87 G25-J85 G25-J87 G25-DV87 G25-J87 G25-DV87 G25-DV87 G25-J87 G25-J85 9 to 104 (2.7"-4.1") M27-J45 M27-J M27-J45 M27-DV47 M27-J45 M27-DV57 M27-DV57 M27-A45 M27-A4 M27-NR5 M27-J87 M27-J85 M27-J87 M27-DV87 M27-J87 M27-DV87 M27-DV87 M27-J87 M27-J85 89 to 140 (.5"-5.5") N7-J45 N7-J N7-J45 N7-DV47 N7-J45 N7-DV57 N7-DV57 N7-A45 N7-A4 N7-NR5 N7-J87 N7-J85 N7-J87 N7-DV87 N7-J87 N7-DV87 N7-DV87 N7-J87 N7-J85 104 to (4.1"-0") W47-J45 W47-J W47-J45 W47-DV47 W47-J45 W47-DV57 W47-DV57 W47-A45 W47-A4 W47-NR5 W47-J87 W47-J85 W47-J87 W47-DV87 W47-J87 W47-DV87 W47-DV87 W47-J87 W47-J85 4 to 84 (2.5"-.") GG25-J45 GG25-J GG25-J45 GG25-J45 GG25-A45 GG25-A4 GG25-J87 GG25-J85 GG25-J87 GG25-J87 GG25-J87 GG25-J85 Guideless Stone Sets 84 to 107 (."-4.2") MM-J45 MM-J MM-J45 MM-J45 MM-A45 MM-A4 MM-J87 MM-J85 MM-J87 MM-J87 MM-J87 MM-J85 102 to 142 (4.0"-5.") NN40-J45 NN40-J NN40-J45 NN40-J45 NN40-A45 NN40-A4 NN40-J87 NN40-J85 NN40-J87 NN40-J87 NN40-J87 NN40-J85 114 to (4.5"-0") WW51-J45 WW51-J WW51-J45 WW51-J45 WW51-A45 WW51-A4 Fe fishg: previously honed holes WW51-J87 WW51-J85 WW51-J87 WW51-J87 WW51-J87 WW51-J85 Keyway Stone Sets Maximum Keyway Width 20. 22.8 0. 5.5 (.8") 4 to 84 (2.5"-.") GY25-J45 GY25-J GY25-J45 GY25-J45 GY25-A45 GY25-A4 GY25-J87 GY25-J85 GY25-J87 GY25-J87 GY25-J87 GY25-J85 (.9") 84 to 107 (."-4.2") MY-J45 MY-J MY-J45 MY-J45 MY-A45 MY-A4 MY-J87 MY-J85 MY-J87 MY-J87 MY-J87 MY-J85 (1.2") 102 to 142 (4.0"-5.") NY40-J45 NY40-J NY40-J45 NY40-J45 NY40-A45 NY40-A4 NY40-J87 NY40-J85 NY40-J87 NY40-J87 NY40-J87 NY40-J85 (1.4") 114 to 42 (4.5"-0") WY51-J45 WY51-J WY51-J45 WY51-J45 WY51-A45 WY51-A4 WY51-J87 WY51-J85 WY51-J87 WY51-J87 WY51-J87 WY51-J85 Approx. R a Surface Fish µm µ 2.00 0.8 2.00 0.75 0.80 1.00 1.80 0.88 0.50 1.00 0.8 0.8 0.8 0.18 0. 0.50 0.75 0.18 0.1 80 80 0 2 40 70 5 20 40 7 20 0 7 5 *1st choice **2nd choice. Use if A4 does not cut. These stones require the use of Master Holders. Superabrasive Stone Sets Metal Bond Diamond and Borazon/CBN Stone Sets Available G25, M27, N7, and W47 stone sizes. These stones can be used to crease stock removal rates or abrasive life when compared to A or J stones or Res or Vitrified Diamond or Borazon/CBN stones. First time users of metal bond superabrasive stone sets must order -KB5X (G25-KB5X) Master Holder Set. Replacement stones can be ordered without reorderg KB5X Master Holders. Master Holder G25-KB5X M27-KB5X N7-KB5X W47-KB5X Stone Set Diameter Range G25- XG55 4-9 2.5-2.7 M27- XG55 9-104 2.7-4.1 N7- XG55 89-140.5-5.5 W47- XG55 104-5 4.1-.5 The the stone set number is for the metal bond abrasive code. This stone set consists of two L1 superabrasive stones and two roughg guides. Select the L1 metal bond superabrasive stone desired from the stone selection guide found on page 9. Master Holders available 4 weeks after receipt of order. Stone sets available 1 week after receipt of order. Vitrified Bond Diamond and Res Borazon/CBN Sets For hong carbide, ceramic, glass and hardened steel. Available 82,55 (.25") or 101, (4") stone length. For 82,55 (.5") length, add -85 to stone number. Diamond Stone DV-47 DV-57 DV-87 DV-07 Borazon Stone NR5 Res Bond NR8 Res Bond The followg stone sets are available from stock: G25-DV57, G25-NR5, M27- DV57, M27-NR5, N7-DV57, N7-NR5, W47-DV57, W47-NR5. All other stone sets available 2 weeks after receipt of order. 14

Stones for AN, ANR, GNH, GNR Hong Units In some cases, stones other than the RECOMMENDED STONES may hone faster or last longer. For long or repetitive production runs, it may be economical to choose a stone slightly harder or softer, coarser or fer. If the stone wears out too fast, use a harder stone; if it does not cut, use a softer stone. Stones parentheses available 2 weeks after receipt of order. Grit Size 80 0 220 280 20 500 70 0 200 280 400 500 00 Hard------Soft Hard-----------Soft Hard---------Soft Hard---------Soft H-S Hard---------Soft H-S H-----S Hard----Soft Hard------Soft Hard------Soft 4 to 9 (2.5"-2.7") (G25-A2) (G25-A25) (G25-A27) (G25-A41) G25-A4 G25-A45 G25-A47 (G25-A) G25-A49 (G25-A55) (G25-A57) (G25-A59) G25-A G25-A5 G25-A7 (G25-A79) (G25-J11) G25-J1 G25-J G25-J17 (G25-J19) G25-J4 G25-J45 G25-J47 (G25-J49) (G25-J55) (G25-J57) (G25-J59) G25-J G25-J5 G25-J7 (G25-J9) G25-J8 G25-J85 G25-J87 (G25-J89) (G25-J9) G25-J95 G25-J97 (G25-CO5) General Purpose 9 to 104 (2.7"-4.1") M27-A2 (M27-A) M27-A25 (M27-A2) M27-A27 (M27-A28) (M27-A41) M27-A4 (M27-A44) M27-A45 (M27-A4) M27-A47 (M27-A) (M27-A49) (M27-A411) (M27-A5) (M27-A55) (M27-A57) (M27-A1) M27-A (M27-A4) M27-A5 (M27-A) M27-A7 (M27-A8) M27-A9 (M27-A75) (M27-A79) (M27-A95) M27-J11 M27-J1 (M27-J14) M27-J (M27-J1) M27-J17 (M27-J18) M27-J19 (M27-J41) M27-J4 (M27-J44) M27-J45 (M27-J4) M27-J47 M27-J M27-J49 (M27-J5) (M27-J55) (M27-J57) (M27-J58) M27-J (M27-J4) M27-J5 (M27-J) M27-J7 (M27-J8) (M27-J9) M27-J8 (M27-J84) M27-J85 (M27-J8) M27-J87 (M27-J88) M27-J89 (M27-J9) (M27-J94) M27-J95 (M27-J9) M27-J97 (M27-J98) (M27-J99) (M27-CO5) These stones require Master Holder Sets. 89 to 140 (.5"-5.5") N7-A2 (N7-A) N7-A25 (N7-A2) N7-A27 (N7-A28) (N7-A41) N7-A4 (N7-A44) N7-A45 (N7-A4) N7-A47 (N7-A) N7-A49 (N7-A411) (N7-A5) (N7-A55) (N7-A57) (N7-A1) N7-A (N7-A4) N7-A5 (N7-A) N7-A7 (N7-A8) (N7-A9) (N7-A75) (N7-A79) (N7-A95) N7-J11 N7-J1 (N7-J14) N7-J (N7-J1) N7-J17 (N7-J18) N7-J19 (N7-J41) N7-J4 (N7-J44) N7-J45 (N7-J4) N7-J47 N7-J N7-J49 (N7-J5) (N7-J55) (N7-J57) (N7-J58) N7-J (N7-J4) N7-J5 (N7-J) N7-J7 (N7-J8) (N7-J9) N7-J8 (N7-J84) N7-J85 (N7-J8) N7-J87 (N7-J88) N7-J89 (N7-J9) (N7-J94) N7-J95 (N7-J9) N7-J97 (N7-J98) (N7-J99) (N7-CO5) 104 to (4.1"-0") W47-A2 (W47-A) W47-A25 (W47-A2) W47-A27 (W47-A28) (W47-A41) W47-A4 (W47-A44) W47-A45 (W47-A4) W47-A47 (W47-A) W47-A49 (W47-A411) (W47-A5) (W47-A55) (W47-A57) (W47-A1) W47-A (W47-A4) W47-A5 (W47-A) W47-A7 (W47-A8) W47-A9 (W47-A75) (W47-A79) (W47-A95) W47-J11 W47-J1 (W47-J14) W47-J (W47-J1) W47-J17 (W47-J18) W47-J19 (W47-J41) W47-J4 (W47-J44) W47-J45 (W47-J4) W47-J47 W47-J W47-J49 (W47-J5) (W47-J55) (W47-J57) (W47-J58) W47-J (W47-J4) W47-J5 (W47-J) W47-J7 (W47-J8) (W47-J9) W47-J8 (W47-J84) W47-J85 (W47-J8) W47-J87 (W47-J88) W47-J89 (W47-J9) (W47-J94) W47-J95 (W47-J9) W47-J97 (W47-J98) (W47-J99) (W47-CO5) Guideless 4 to 84 84 to 107 102 to 142 114 to (2.5"-.") (."-4.2") (4.0"-5.") (4.5"-0") Alumum Oxide Stones GG25-A2 MM-A2 NN40-A2 WW51-A2 (MM-A) (NN40-A) (WW51-A) GG25-A25 MM-A25 NN40-A25 WW51-A25 (MM-A2) (NN40-A2) (WW51-A2) GG25-A27 MM-A27 NN40-A27 WW51-A27 (MM-A28) (NN40-A28) (WW51-A28) (GG25-A41) GG25-A4 GG25-A45 GG25-A47 (GG25-A) (GG25-A49) (GG25-A55) (GG25-A57) (GG25-A59) (GG25-A) GG25-A5 (GG25-A7) (GG25-A79) (GG25-J11) GG25-J1 GG25-J GG25-J17 (GG25-J19) GG25-J4 GG25-J45 (GG25-J47) (GG25-J49) (GG25-J55) (GG25-J57) (GG25-J59) (GG25-J) (GG25-J5) (GG25-J7) (GG25-J9) (GG25-J8) GG25-J85 GG25-J87 (GG25-J89) (GG25-J9) GG25-J95 (GG25-J97) GG25-CO5 (MM-A41) MM-A4 MM-A45 MM-A47 (MM-A) (MM-A49) (MM-A5) (MM-A55) (MM-A57) (MM-A1) MM-A (MM-A4) MM-A5 (MM-A) MM-A7 (MM-A8) MM-A9 (MM-A75) (MM-A79) (MM-A95) (NN40-A41) NN40-A4 NN40-A45 NN40-A47 (NN40-A) (NN40-A49) (NN40-A5) (NN40-A55) (NN40-A57) (NN40-A1) NN40-A (NN40-A4) NN40-A5 (NN40-A) NN40-A7 (NN40-A8) NN40-A9 (NN40-A75) (NN40-A79) (NN40-A95) Silicon Carbide Stones (MM-J11) (NN40-J11) MM-J1 NN40-J1 (MM-J14) (NN40-J14) MM-J NN40-J (MM-J1) (NN40-J1) MM-J17 NN40-J17 (MM-J18) (NN40-J18) (MM-J19) (NN40-J19) (MM-J41) (NN40-J41) MM-J4 NN40-J4 (MM-J44) (NN40-J44) MM-J45 NN40-J45 (MM-J4) (NN40-J4) (MM-J47) NN40-J47 (MM-J) (NN40-J) (MM-J49) (NN40-J49) (MM-J5) (NN40-J5) (MM-J55) (NN40-J55) (MM-J57) (NN40-J57) (MM-J58) (NN40-J58) MM-J (NN40-J) (MM-J4) (NN40-J4) MM-J5 (NN40-J5) (MM-J) (NN40-J) MM-J7 (NN40-J7) (MM-J8) (NN40-J8) (MM-J9) (NN40-J9) (MM-J8) NN40-J8 (MM-J84) (NN40-J84) MM-J85 NN40-J85 (MM-J8) (NN40-J8) MM-J87 NN40-J87 (MM-J88) (NN40-J88) (MM-J89) NN40-J89 (MM-J9) (NN40-J9) (MM-J94) (NN40-J94) MM-J95 NN40-J95 (MM-J9) (NN40-J9) (MM-J97) (NN40-J97) (MM-J98) (NN40-J98) (MM-J99) (NN40-J99) MM-CO5 NN40-CO5 (WW51-A41) WW51-A4 WW51-A45 WW51-A47 (WW51-A) (WW51-A49) (WW51-A5) (WW51-A55) (WW51-A57) (WW51-A1) WW51-A (WW51-A4) WW51-A5 (WW51-A) WW51-A7 (WW51-A8) WW51-A9 (WW51-A75) (WW51-A79) (WW51-A95) (WW51-J11) WW51-J1 (WW51-J14) WW51-J (WW51-J1) WW51-J17 (WW51-J18) (WW51-J19) (WW51-J41) WW51-J4 (WW51-J44) WW51-J45 (WW51-J4) (WW51-J47) (WW51-J) (WW51-J49) (WW51-J5) (WW51-J55) (WW51-J57) (WW51-J58) (WW51-J) (WW51-J4) WW51-J5 (WW51-J) WW51-J7 (WW51-J8) (WW51-J9) WW51-J8 (WW51-J84) WW51-J85 (WW51-J8) WW51-J87 (WW51-J88) (WW51-J89) (WW51-J9) (WW51-J94) WW51-J95 (WW51-J9) (WW51-J97) (WW51-J98) (WW51-J99) WW51-CO5 Keyway Maximum Keyway Width 20, 22,8 0,4,5 (.8") (.9") (1.2") (1.4") 4 to 84 84 to 107 102 to 142 114 to (2.5"-.") (."-4.2") (4.0"-5.") (4.5"-0") (GY25-A2) (GY25-A25) (GY25-A27) (GY25-A41) GY25-A4 GY25-A45 GY25-A47 (GY25-A) (GY25-A49) (GY25-A55) (GY25-A57) (GY25-A59) (GY25-A) GY25-A5 GY25-A7 (GY25-A79) (GY25-J11) (GY25-J1) (GY25-J) (GY25-J17) (GY25-J19) (GY25-J4) GY25-J45 GY25-J47 (GY25-J49) (GY25-J55) (GY25-J57) (GY25-J59) (GY25-J) GY25-J5 GY25-J7 (GY25-J9) (GY25-J8) GY25-J85 GY25-J87 (GY25-J89) (GY25-J9) (GY25-J95) (GY25-J97) (GY25-CO5) (MY-A2) (MY-A) (MY-A25) (MY-A2) (MY-A27) (MY-A28) (MY-A41) MY-A4 MY-A45 MY-A47 (MY-A) (MY-A49) (MY-A55) (MY-A57) (MY-A59) (MY-A1) (MY-A) (MY-A4) MY-A5 (MY-A) MY-A7 (MY-A8) (MY-A9) (MY-A75) (MY-A79) (MY-A95) (MY-J11) (MY-J1) (MY-J14) (MY-J) (MY-J1) (MY-J17) (MY-J18) (MY-J19) (MY-J41) (MY-J4) (MY-J44) MY-J45 (MY-J4) MY-J47 (MY-J) (MY-J49) (MY-J5) (MY-J55) (MY-J57) (MY-J58) (MY-J) (MY-J4) MY-J5 (MY-J) MY-J7 (MY-J8) (MY-J9) (MY-J8) (MY-J84) MY-J85 (MY-J8) MY-J87 (MY-J88) (MY-J89) (MY-J9) (MY-J94) MY-J95 (MY-J9) (MY-J97) (MY-J98) (MY-J99) MY-CO5 (NY40-A2) (NY40-A) (NY40-A25) (NY40-A2) (NY40-A27) (NY40-A28) (NY40-A41) NY40-A4 NY40-A45 NY40-A47 (NY40-A) (NY40-A49) (NY40-A55) (NY40-A57) (NY40-A59) (NY40-A1) (NY40-A) (NY40-A4) NY40-A5 (NY40-A) NY40-A7 (NY40-A8) (NY40-A9) (NY40-A75) (NY40-A79) (NY40-A95) (NY40-J11) (NY40-J1) (NY40-J14) (NY40-J) (NY40-J1) (NY40-J17) (NY40-J18) (NY40-J19) (NY40-J41) (NY40-J4) (NY40-J44) NY40-J45 (NY40-J4) NY40-J47 (NY40-J) (NY40-J49) (NY40-J5) (NY40-J55) (NY40-J57) (NY40-J58) (NY40-J) (NY40-J4) NY40-J5 (NY40-J) NY40-J7 (NY40-J8) (NY40-J9) (NY40-J8) (NY40-J84) NY40-J85 (NY40-J8) NY40-J87 (NY40-J88) (NY40-J89) (NY40-J9) (NY40-J94) (NY40-J95) (NY40-J9) (NY40-J97) (NY40-J98) (NY40-J99) (NY40-CO5) (WY51-A2) (WY51-A) (WY51-A25) (WY51-A2) (WY51-A27) (WY51-A28) (WY51-A29) (WY51-A41) WY51-A4 WY51-A45 WY51-A47 (WY51-A) (WY51-A49) (WY51-A55) (WY51-A57) (WY51-A59) (WY51-A1) (WY51-A) (WY51-A4) WY51-A5 (WY51-A) WY51-A7 (WY51-A8) (WY51-A9) (WY51-A75) (WY51-A79) (WY51-A95) (WY51-J11) (WY51-J1) (WY51-J14) WY51-J (WY51-J1) WY51-J17 (WY51-J18) (WY51-J19) (WY51-J41) WY51-J4 (WY51-J44) WY51-J45 (WY51-J4) WY51-J47 (WY51-J) (WY51-J49) (WY51-J5) (WY51-J55) (WY51-J57) (WY51-J58) (WY51-J) (WY51-J4) WY51-J5 (WY51-J) WY51-J7 (WY51-J8) (WY51-J9) (WY51-J8) (WY51-J84) WY51-J85 (WY51-J8) WY51-J87 (WY51-J88) (WY51-J89) (WY51-J9) (WY51-J94) (WY51-J95) (WY51-J9) (WY51-J97) (WY51-J98) (WY51-J99) (WY51-CO5)

Additional Portable Accessories Teflon-Mounted Hone Holders for Portable Hones Used to fish oil-free air compressor cylder sleeves. Provides a slippery Teflon coatg that is compatible with Teflon rider rgs. Made from % glass filled Teflon and are used on Sunnen Model AN-1, AN-8, and ANR-275 Portable Hones. (Smaller sizes are available for JN/JNR, and SN/SNR Portable Hones on a special order basis. Call Sunnen Products, Customer Service Department for formation.) These Teflon Hones are used followg a 400 grit fishg stone. The recoended procedure when usg Teflon stones is to use them dry and with light pressure. Eight full passes up and down the cylder wall is usually sufficient. Teflon-Mounted Hone Holders Available Diameter Range 4-84 84-107 102-142 114-18 PHT Plateau Hong Tools For AN, ANR, GNH and GNR Hones Sunnen s PHT tools are used as a fal fishg step, after itial hong to provide a plateau surface on cylder walls. Made from special abrasive impregnated filament. For additional formation contact your local Sunnen Field Engeer or call Customer Service toll-free St. Louis For Diameter Range 75,7-9,0 9,0-118,9 11,8-4,4,5-,0 2.5-..-4.2 4.0-5. 4.5-7.2 2.98-.78.78-4.8 4.-.08 4.98-0.0 4 Strips GG25-XB25 MM-XB25 NN40-XB25 W47-XB25* * Available from fished good stock. All others available on special order basis. Abrasive Sets General Purpose 4 Brushes (20 Grit) GG-PHT-72 MM-PHT-71 NN-PHT-71 WW-PHT-71 8 Strips GY25-XB25 MY-XB25 NY40-XB25 W51-XB25 Abrasive Sets Production 8 Brushes (20 Grit) GY-PHT-72 MY-PHT-71 NY-PHT-71 WY-PHT-71 1

P-180/P-200 Portable Mache Toolg 4,70 5.185" 1.75" P-180 Honall A portable mandrel driver for sizg and fishg holes work too bulky or heavy to take to the hong mache. Uses the same mandrels and stones used on Sunnen Hong Maches. The adapters listed below must be used as they are different from the adapters used on Sunnen Maches. A quick-release lever retracts the stone and speeds removal of tool from the work. Power source should be a 10 (/8") chuck capacity drill with approximately 50 RPM. Each Honall is furnished with 7 (.25") and 10 (/8") solid drive shafts and a 10 (/8") drive shaft with build- universal jot. Weight:,5 kg (1 lb.) Orderg Information for P-180 Honall Refer to pages 20-47 and 0-75 for selection of items, 4 and 5. Diameter Range 4.70-5.185" -1.75",185-,5,5-,08,08-,70,70-,495,495-,19,19-,744,744-,775,775-1,01 1,01-1,250 1,250-1,75 4.70-.22.22-7.82 7.82-9.40 9.40-.57.57-.72.72-18.90 18.90-19.9 19.9-2.19 2.19-1.75 1.75-4.9 Order 1- For Complete P-180 or P-200 Unit 2 Mandrel Adapter Hong Driver 1 Head and P-180 or P-200 P-180 Assembled with BL Mandrel Unit K, BL, BAL Mandrels Y Mandrels JK, L Mandrels* PSK-A PK8-A PK10-A PK-A PK1-A PK20-A PAK20-A PAK20-A PAK20-A not available and P-200 Sidewder NA PK8-A PK10-A PK-A PK1-A PK20-A PAK20-A PAK20-A PAK20-A PAK20-A P-200 Sidewder Assembled with K1 Mandrel Unit P-200 Sidewder Similar to the P-180 Honall, the P200 Sidewder floats on ball beargs with no universal jot required. Tool does not whip durg hong or when removg tool from hole. Ideally suited for short bore hong. Recoended power source is a drill press, millg mache or any other rigid drive unit with a 1 (.5") chuck capacity. Weight: 1,4 kg ( lbs.) LN-590A LN-08A LN-08A LN-702A LN-70A LN-704A LN-704A LN-92A not available not available Mandrel When orderg a mandrel the 4,70-,22 (.185"-.5") range add the prefix S to the number. SK- XXXYY. The shank of an SK mandrel is 25 (1") shorter than the shank of s standard K mandrel. SK mandrels are available hard steel only. Mandrels with tegral adapters cannot be used with P-180 or P-200. Use GGN-0 Mandrel Driver for applications requirg tegral adapter mandrels. 4 Trug Sleeve 5 Hong Stones See Stone Tables Pages 20-41 * When orderg JK or L mandrels, a different stone retaer must be used. Order the appropriate adapter from the adjacent columns. Remove the retaer supplied with adapter and replace with the correct stone retaer. GGN-0 Assembled with 2H-P28-2500WG The GGN-0 is a portable mandrel driver for hong larger bores where the hone must be taken to the work. Uses same hong units as Sunnen Hong Mache. Especially designed for holes 19,05 (.75") and larger, where the bore length is at least three times the diameter. Features clude sprg-loaded adjustable cuttg pressure, easyto-use stone feed-up control, and quick-release lever to retract stone for removal of hong unit from the work. Includes LN- 011A Eccentric Sleeve. Suggested drivg power should be at least a,7 (.5") heavy-duty drill with a 275-450 RPM range. How to order For complete hong tool, order: Hong Oil See page 17 and 174 for the correct Hong Oil for your application. GGN-0 Mandrel Driver 19 98.744".875" 1. GGN-0 Mandrel Driver (cludes one Universal Jot) 2. Order complete Hong Unit as would be required if the job were to be done on a Sunnen Hong Mache. (Refer to pages 49-59 and 8-9 for toolg.). If GGN-0 is to be used a rigid strokg device, order additional Universal Jot AN-70. 4. For stant couplg or uncouplg of drive shaft, order Quick Coupler AN-80. Weight 1,2 kg (2.5 lbs.) 17