TECHNICAL DATASHEET FOR LOOSE TUBE OPTICAL FIBER CABLE Air Blown Micro LC Cable ITU-T G.652.D 6~72F Customer : Czech Atlantis Date : Oct. 31. 2007 Author : MinLi Fu Manager : HanDong Choi Department : Research & Development Department Sales Engineering Part SAMSUNG ELECTRONICS HAINAN FIBEROPTICS Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 1 of 10
45 Document No.: K7COC31A_Rev.01 1. Scope 1.1. This document details external cables generally for installation into a micro duct by air blown installation. 1.2. Air Blown Micro cables provides a lower initial investment. The network operator installs more cables as required. 1.3. The cable shall contain max. 72 optical fibers. Concept Drawing Controller 31 84 Compressed Air Main Cable Duct Compressor Sub-Duct Cable Cable Drum Air Blowing Machine Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 2 of 10
2. Fibers 2.1. Fibers supplied against this specification must meet the requirements of ITU-T recommendation G.652.D (WidePass TM1 ) fibers. 2.2. G.652.D fibers 2.2.1. Optical specifications Attenuation Parameters Unit Specifications 1310 nm 0.35 1383 ± 3 nm db/km 0.35 1550 nm 0.22 Attenuation uniformity 1550nm db/km 0.10 Point Discontinuities 1310 & 1550 nm db 0.05 Attenuation Vs Wavelength Mode Field Diameter 1285 ~ 1330 nm db/km 0.05 1525 ~ 1575 nm db/km 0.03 1310 nm um 9.2 ± 0.4 1550 nm um 10.4 ± 0.5 Cable cutoff Wavelength (λcc) nm 1260 Dispersion 1285 ~ 1330 nm 3.0 ps/(nm.km) 1550 nm 17.5 Zero dispersion wavelength Zero dispersion slope nm 1302 ~ 1322 ps/(nm 2.km) 0.091 PMD Q (Link Design Value) 1550 nm ps/km 1/2 0.2 1 WidePass TM is a trademark of SAMSUNG Electronics (Hainan) Fiberoptics Co., Ltd. Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 3 of 10
2.2.2. Dimensional Specifications Parameters Unit Specifications Cladding Diameter um 125.0 ± 1.0 Cladding Non-circularity % 1.0 Core/Cladding Concentricity Error um 0.6 Coating Diameter [Uncolored] um 245 ± 5 Coating Outer Non-Circularity % 6.0 Coating Concentricity Error um 12.5 2.2.3. Mechanical and Environmental Specifications Parameters Unit Specifications Proof Test Level GPa (Kpsi) 0.7 ( 100) Coating Strip Force N 1.3 ~ 8.9 Dynamic Tensile Strength (Gauge Length: 0.5m) Temperature Dependence (-60 o C ~ +85 o C) Temp.-Humidity Cycling (-10 o C ~ +85 o C, 98% RH) Water Immersion @ 23 ± 2 o C Hot Aging @ 85 ± 2 o C GPa db/km db/km db/km db/km Mean value 4.0 (RH 50%) 0.05 @1310nm & 1550nm 0.05 @1310nm & 1550nm 0.05 @1310nm & 1550nm 0.05 @1310nm & 1550nm Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 4 of 10
3. Cable construction 3.1. A typical cable construction can be seen in Appendix 1. 3.2. Fiber Color code No. 1 2 3 4 5 6 Color Blue Orange Green Brown Grey White No. 7 8 9 10 11 12 Color Red Black Yellow Violet Pink Turquoise 3.3. Cable sheath marking 3.3.1. Marking legend 2 200X SAMSUNG ABMC LC SM XX = XXXX M = - 200X : manufacturing year (Example: 2007) - SAMSUNG : Manufacturer name - ABMC LC : Cable type (Air Blown Micro Cable LC type) - SM : Fiber type(itu-t G.652.D) - XX : Number of optical fiber - XXXX : The figure of meter - The marking is printed every 1 meter 3.3.2. Sheath marking method : ink jet printing(white) 3.4. Both ends of cable are sealed with heat shrinkable end cap to prevent ingress of water. 2 Outer sheath marking legend can be change according to user s requests. Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 5 of 10
4. Cable Properties 4.1. Mechanical & Environmental properties 4.1.1. Minimum Cable bending radius: 10 x cable diameter (during operation) 15 x cable diameter (during installation) 4.1.2. Mechanical & Environmental properties Operating temperature range : -30 o C to + 70 o C Storage/Transport temperature range : -30 o C to + 70 o C Installation temperature range : -20 o C to + 70 o C 4.2. Mechanical & Environmental Requirements No Item Test Specification Test Method Specification 1 Tensile Test IEC-794-1-2- E1 - Load : 500N - Sample length: 100 meters - Time: 5 minutes - Loss change : 0.05 db (after test) 2 Impact test IEC-794-1-2- E4 - Impact energy : 2J - Radius: 300 mm - Number of impacts : 1 - Loss change : (after test) 0.1 db at 1550 3 Crush Resistance IEC-794-1-2- E3 - Load : 500 N/10cm -Time : 5 minutes - Length: 100 mm - Loss change: (during test) 0.1 db at 1550nm 4 Temp. Cycling test IEC-794-1-2- F1 - Temperature step: +20 o C -30 o C +70 o C -30 o C +70 o C +20 o C - Time per each step: 8 hrs - Loss change 0.1 db/km at 1550nm 5 Water penetration IEC-794-1-2- F5B - Water height: 1 m - Sample length: 3m - Duration of test: 12 hrs - No water leakage at the end of the sample Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 6 of 10
5. Packing and Shipping Tag 5.1. Packing 5.1.1. Non-returnable wooden drum 5.1.2. Pallet and Lamiflex are used for the shipment 5.1.3. After cable winding, Data sheet is attached before Lamiflex covering ATLANTIS Roll Shipping tag Cable Data Sheets. Do Not Remove! Caution Plate END < Wooden Drum > 5.2. Shipping Tag 5.2.1. All information that is indicated in the tag is expressed with the bar code. 5.2.2. Information in the tag could be changeable upon mutual agreement. 5.2.3. The tag is weatherproof with plastic coating. 5.2.4. The tag will be attached on both side of a drum. DRUM NO: SHIP TO: DELIVERY ADDRESS *BAR CODE* PO NO: *BAR CODE* QUANTITY/DM *BAR CODE* CUSTOMER PART NO *BAR CODE* MANUFACTURER S PART NO SHIP FROM SITE FOR: SAMSUNG Electronics Hainan Fiberoptics ATTN: P.R.C.570216 C02-C06 Haikou Free Trade Zone, Nanhai Avenue 168, Haikou City, Hainan Province, China m ISE: OSE: ACT: m m m WEIGHT (NET/GROSS): / KGS FO CABLE: CABLE TYPE XX F dia. mm <Shipping Tag > Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 7 of 10
Appendix 1 1. Cable Construction 1.1 Air Blown LC Cable drawing of 72 fibers cable Colored optical fiber Gel- filled Loose tube FRP strength member Water blocking yarn Rip cord Outer black PE Jacket *Filler: Natural (If Necessary) 1.2 Weights and dimensions Fiber Count Number of Total Unit (Tube + Filler) Number of Fibers per tube Outer Diameter 3 (Nominal*) Weight (Nominal) Nominal Delivery Length per Reel 4 Tensile Strength mm kg/km m N 6 6 (1T + 5F ) 6 5.8 26 4,000 500 12 6 (3T + 3F ) 4 5.8 26 4,000 500 24 6 (6T + 0F ) 4 5.8 27 4,000 500 32 6 (4T + 2F ) 8 5.8 28 4,000 500 36 6 (3T + 3F ) 12 5.8 27 4,000 500 48 6 (4T + 2F ) 12 5.8 28 4,000 500 60 6 (5T + 1F ) 12 5.8 29 4,000 500 72 6 (6T + 0F ) 12 5.8 29 4,000 500 *Average Maximum Cable diameter is 6.0mm. 3 The nominal outer diameter may vary by ±5% 4 Maximum delivery length can change under mutual agreement. Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 8 of 10
Revision History DATE AUTHOR REVISION PAGE COMMENTS Oct. 31 2007 MinLi Fu - - Initial Release Jan. 31 2008 MinLi Fu Rev.01 8 Update fiber number per tube for 12F~24F 12F/Tube 4F/Tube 2007 Samsung Electronics Hainan Fiberoptics. Co., Ltd. All Rights Reserved. At the time of its preparation, the information in this document is accurate. However, Samsung Electronics Hainan Fiberoptics makes no warranty or representation with respect to its accuracy and disclaims all liability, which may result from inaccuracies, or third-party use, or third-party reliance. This information is subject to change without notice. Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 9 of 10
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, or otherwise, without the prior written consent of Samsung Electronics Hainan Fiberoptics. Samsung Electronics Hainan Fiberoptics assumes no responsibility for its use, or for infringements of patents or other rights of third parties. This document implies no license under patents or copyrights. Trademarks in this document belong to their respective companies. Samsung Electronics Hainan Fiberoptics Co., Ltd. Page 10 of 10