MP2303 3A, 28V, 340KHz Synchronous Rectified Step-Down Converter

Similar documents
MP2307 3A, 23V, 340KHz Synchronous Rectified Step-Down Converter

MP1482 2A, 18V Synchronous Rectified Step-Down Converter

MP2305 2A, 23V Synchronous Rectified Step-Down Converter

MP1570 3A, 23V Synchronous Rectified Step-Down Converter

MP2307 3A, 23V, 340KHz Synchronous Rectified Step-Down Converter

MP1484 3A, 18V, 340KHz Synchronous Rectified Step-Down Converter

MP2355 3A, 23V, 380KHz Step-Down Converter

MP1482 2A, 18V Synchronous Rectified Step-Down Converter

FEATURES DESCRIPTION APPLICATIONS PACKAGE REFERENCE

MP2363 3A, 27V, 365KHz Step-Down Converter

MP2354 2A, 23V, 380KHz Step-Down Converter

Techcode. 1.6A 32V Synchronous Rectified Step-Down Converte TD1529. General Description. Features. Applications. Package Types DATASHEET

MP A, 15V, 800KHz Synchronous Buck Converter

MP1472 2A, 18V Synchronous Rectified Step-Down Converter

MP1482 2A, 18V Synchronous Rectified Step-Down Converter

SGM6232 2A, 38V, 1.4MHz Step-Down Converter

SGM6132 3A, 28.5V, 1.4MHz Step-Down Converter

MP2303A 3A, 28V, 360kHz Synchronous Rectified Step-Down Converter

MP A, 28V, 1.4MHz Step-Down Converter

Analog Technologies. ATI2202 Step-Down DC/DC Converter ATI2202. Fixed Frequency: 340 khz

MP A, 15V, 800kHz Synchronous Buck Converter

idesyn id8802 2A, 23V, Synchronous Step-Down DC/DC

LSP5502 2A Synchronous Step Down DC/DC Converter

MP kHz, 55V Input, 2A High Power LED Driver

SGM6130 3A, 28.5V, 385kHz Step-Down Converter

EUP3410/ A,16V,380KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

MP V Input, 2A Output Step Down Converter

MP2494 2A, 55V, 100kHz Step-Down Converter

MP A, 24V, 1.4MHz Step-Down Converter

MP A, 55V, 100kHz Step-Down Converter with Programmable Output OVP Threshold

HM1410 FEATURES APPLICATIONS PACKAGE REFERENCE HM1410

AT V,3A Synchronous Buck Converter

EUP3452A. 2A,30V,300KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

MP A, 30V, 420kHz Step-Down Converter

MP A, 5.5V Synchronous Step-Down Switching Regulator

EUP A,40V,200KHz Step-Down Converter

MP A, 36V, 700KHz Step-Down Converter with Programmable Output Current Limit

MP9141 FEATURES DESCRIPTION APPLICATIONS PACKAGE REFERENCE

MP1430 3A, 28V, 385KHz Step-Down Converter

MP2362 Dual 2A, 23V, 380KHz Step-Down Converter with Frequency Synchronization

MP4458 1A, 4MHz, 36V Step-Down Converter

MP A, 4MHz, 50V Step-Down Converter

PACKAGE REFERENCE. ELECTRICAL CHARACTERISTICS V IN = 12V, T A = +25 C, unless otherwise noted.

MP A, 24V, 700KHz Step-Down Converter

MP2482 5A, 30V, 420kHz Step-Down Converter

HF A 27V Synchronous Buck Converter General Description. Features. Applications. Package: TBD

SR A, 30V, 420KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION

MP A, 4MHz, 36V Step-Down Converter

MP A, 4MHz, 36V Step-Down Converter

AME. 40V CC/CV Buck Converter AME5244. n General Description. n Typical Application. n Features. n Functional Block Diagram.

AIC2858 F. 3A 23V Synchronous Step-Down Converter

AT V Synchronous Buck Converter

MP2497-A 3A, 50V, 100kHz Step-Down Converter with Programmable Output OVP Threshold

MP3115 High-Efficiency, Single-Cell Alkaline, 1.3MHz Synchronous Step-up Converter with Output Disconnect

Pin Assignment Pin No. Pin Name Descripition 1 BS High-Side Gate Drive Boost Input. BS supplies the drive for the highside N-Channel MOSFET switch. Co

EUP A,30V,500KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

MP A, 50V, 1.2MHz Step-Down Converter in a TSOT23-6

PRODUCTION DATA SHEET

NX7101 2A, High Voltage Synchronous Buck Regulator

General Description BS SW LSP5526. C4 1.6nF R3 C5 NC 10K. shows a sample LSP5526 application circuit generating 5V/2A output

BS SW LSP5522. C4 16nF R3 C5 NC 10K. shows a sample LSP5522 application circuit generating 5V/2A output

MP8619 8A, 25V, 600kHz Synchronous Step-down Converter

Thermally enhanced Low V FB Step-Down LED Driver ADT6780

MP2225 High-Efficiency, 5A, 18V, 500kHz Synchronous, Step-Down Converter

MPQ4561-AEC1. 1.5A, 2MHz, 55V Step-Down Converter Available in AEC-Q100 DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION

MPQ4456 Industrial Grade,1A, 4MHz, 36V Step-Down Converter

MP1495 High Efficiency 3A, 16V, 500kHz Synchronous Step Down Converter

MA V Synchronous Buck Converter GENERAL DESCRIPTION FEATURES APPLICATION CIRCUIT

EUP3475 3A, 28V, 1MHz Synchronous Step-Down Converter

MP2109 Dual 1.2MHz, 800mA Synchronous Step-Down Converter

MP V, 3A, 600kHz Synchronous Step-Down Converter

MP MHz, 18V Step-Up Converter

MP2115 2A Synchronous Step-Down Converter with Programmable Input Current Limit

MP2452 1A, 36V, 1MHz Step-Down Converter

NOT RECOMMENDED FOR NEW DESIGNS REFER TO MP2147 MP Ultra Low Voltage, 4A, 5.5V Synchronous Step-Down Switching Regulator DESCRIPTION FEATURES

AT V 5A Synchronous Buck Converter

MP2107/MP2107A 4A, 6V Synchronous Step-Down Switching Regulator

MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter

MP KHz/1.3MHz Boost Converter with a 2A Switch

MP A, 24V, 1.4MHz Step-Down Converter in a TSOT23-6

AME. High Voltage CC/CV Buck Converter AME5265. n Features. n General Description. n Applications. n Typical Application. n Functional Block Diagram

23V 3A Step-Down DC/DC Converter

2A, 23V, 380KHz Step-Down Converter

ELM614BA 2A, 18V, 500kHz, synchronous step down DC/DC converter

3A, 23V, 380KHz Step-Down Converter

UNISONIC TECHNOLOGIES CO., LTD UCC36351 Preliminary CMOS IC

MP A, 500KHz Synchronous Rectified Step-up Converter

3A, 36V, Step-Down Converter

MP V, 4A Synchronous Step-Down Coverter

MP5410 Low Start-up Voltage Boost Converter with Four SPDT Switches

MP A, 55V, 480kHz Step-Down Converter in a TSOT23-6

MP A, 24V, 1.4MHz Step-Down White LED Driver

LSP A 23V Synchronous Buck Converter. General Description. Features. Applications. LSP5526 Rev of /8/1.

2A, 23V, 340KHz Synchronous Step-Down Converter

MP2314S 2A, 24V, 500kHz, High-Efficiency, Synchronous, Step-Down Converter

MP2249 1MHz, 6V, 3A, Low-Voltage Synchronous Step-Down Converter

24V, 2A, 340KHz Synchronous Step-Down DC/DC Converter

EUP A,30V,1.2MHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

MP V, 700kHz Synchronous Step-Up White LED Driver

MP A, 24V, 1.4MHz Step-Down Converter in a TSOT23-6

Transcription:

MP2303 3A, 28V, 340KHz Synchronous Rectified Step-Down Converter TM The Future of Analog IC Technology DESCRIPTION The MP2303 is a monolithic synchronous buck regulator. The device integrates power MOSFETS that provide 3A continuous load current over a wide operating input voltage of 4.75V to 28V. Current mode control provides fast transient response and cycle-by-cycle current limit. An adjustable soft-start prevents inrush current at turn-on. In shutdown mode, the supply current drops to µa. This device, available in 8-pin SOIC and 3x3 0-pin QFN packages, provides a very compact system solution with minimal reliance on external components. EVALUATION BOARD REFERENCE Board Number Dimensions EV2303DN-00A 2.0 X x.5 Y x 0.5 Z FEATURES 3A Output Current Wide 4.75V to 28V Operating Input Range Integrated Power MOSFET Switches Output Adjustable from 0.8V to 25V Up to 95% Efficiency Programmable Soft-Start Stable with Low ESR Ceramic Output Capacitors Fixed 340KHz Frequency Cycle-by-Cycle Over Current Protection Input Under Voltage Lockout Thermally Enhanced 8-Pin SOIC and 3x3 QFN0 Packages APPLICATIONS Distributed Power Systems Pre-Regulator for Linear Regulators Notebook Computers MPS and The Future of Analog IC Technology are Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION VIN 4.75V-28V C5 0nF BS SS IN EN MP2303 SW COMP GND FB C3 3.3nF EFFICIENCY (%) 00 90 80 70 Efficiency vs Load Current VIN = 2V VIN = 24V 5V/3A 60 50 = 5V 0 0.5.0.5 2.0 2.5 3.0 LOAD CURRENT (A) MP2303_TAC0 MP2303-EC0 MP2303 Rev. 0.92 www.monolithicpower.com

PACKAGE REFERENCE TOP VIEW TOP VIEW IN 0 SS BS 8 SS SW 2 9 BS IN 2 7 EN GND 3 8 EN SW 3 6 COMP GND 4 7 COMP GND 4 5 FB GND 5 6 FB MP2303_PD0_SOIC8N EXPOSED PAD ON BACKSIDE MP2303_PD02_QFN0 Part Number* Package Temperature MP2303DN SOIC8N (Exposed Pad) * For Tape & Reel, add suffix Z (eg. MP2303DN Z) For RoHS compliant packaging, add suffix LF (eg. MP2303DN LF Z) 40 C to 85 C ABSOLUTE MAXIMUM RATINGS () Supply Voltage V IN... 0.3V to 30V Switch Voltage V SW... V to V IN 0.3V Boost Voltage V BS...V SW 0.3V to V SW 6V All Other Pins... 0.3V to 6V Junction Temperature...50 C Lead Temperature...260 C Storage Temperature... 65 C to 50 C Part Number* Package Temperature MP2303DQ 3mm x 3mm QFN0 * For Tape & Reel, add suffix Z (eg. MP2303DQ Z) For RoHS compliant packaging, add suffix LF (eg. MP2303DQ LF Z) 40 C to 85 C Recommended Operating Conditions (2) Input Voltage V IN... 4.75V to 28V Output Voltage V OUT... 0.8V to 25V Ambient Operating Temperature... 40 C to 85 C Thermal Resistance (3) θ JA θ JC SOIC8N... 50... 0... C/W 3x3 QFN0... 50... 2... C/W Notes: ) Exceeding these ratings may damage the device. 2) The device is not guaranteed to function outside of its operating conditions. 3) Measured on approximately square of oz copper. ELECTRICAL CHARACTERISTICS (4) V IN = 2V, T A = 25 C, unless otherwise noted. Parameter Symbol Condition Min Typ (4) Max Units Shutdown Supply Current V EN = 0V 0.3 3.0 µa Supply Current V EN = 2.7V, V FB =.0V.3.5 ma 4.75V V IN 28V, Feedback Voltage V FB T A = 25 C 0.780 0.800 0.820 V 40 C T A 85 C 0.772 0.828 V OVP Threshold Voltage 0.90 0.95.00 V Error Amplifier Voltage Gain A EA 400 V/V Error Amplifier Transconductance G EA I C = ±0µA 550 820 00 µa/v MP2303 Rev. 0.92 www.monolithicpower.com 2

ELECTRICAL CHARACTERISTICS (4) (continued) V IN = 2V, T A = 25 C, unless otherwise noted. Parameter Symbol Condition Min Typ (4) Max Units High-Side Switch-On Resistance R DS(ON) 25 mω Low-Side Switch-On Resistance R DS(ON)2 25 mω High-Side Switch Leakage Current V EN = 0V, V SW = 0V 0 0 µa Upper-Switch Current Limit 4.3 6.3 A Lower-Switch Current Limit From Drain to Source.25 A COMP to Current Sense Transconductance Oscillation Frequency G CS 9 A/V F osc T A = 25 C 300 340 380 KHz 40 C T A 85 C 270 400 KHz Short Circuit Oscillation Frequency F osc2 V FB = 0V 0 KHz Maximum Duty Cycle D MAX V FB = 0.7V 90 % Minimum On-Time 220 ns EN Shutdown Threshold Voltage V EN Rising..5 2.0 V EN Shutdown Threshold Voltage Hysteresis EN Lockout Threshold Voltage 220 mv 2.2 2.5 2.7 V 40 C T A 85 C 2. 2.8 V EN Lockout Hysteresis 20 mv Input Under Voltage Lockout Threshold Input Under Voltage Lockout Threshold Hysterisis UVLO V IN rising, T A = 25 C 3.8 4.05 4.30 V 40 C T A 85 C 3.5 4.70 V 20 mv Soft-Start Current V SS = 0V 6 µa Thermal Shutdown 60 C Note: 4) 00% production test at 25 C. Specifications over the temperature range are guaranteed by design and characterization. MP2303 Rev. 0.92 www.monolithicpower.com 3

PIN FUNCTIONS SOIC8N Pin # 3x3 QFN0 Pin # 9 BS 2 IN 3 2 SW 4 3, 4, 5 GND 5 6 FB 6 7 COMP 7 8 EN 8 0 SS Name Description High-Side Gate Drive Boost Input. BS supplies the drive for the high-side N- Channel MOSFET switch. Connect a 0.0µF or greater capacitor from SW to BS to power the high side switch. Power Input. IN supplies the power to the IC, as well as the step-down converter switches. Drive IN with a 4.75V to 28V power source. Bypass IN to GND with a suitably large capacitor to eliminate noise on the input to the IC. See Input Capacitor. Power Switching Output. SW is the switching node that supplies power to the output. Connect the output LC filter from SW to the output load. Note that a capacitor is required from SW to BS to power the high-side switch. Ground. SOIC8: Connect the exposed pad to pin 4. 3x3 QFN0: Connect to pins 3, 4 and 5 and ensure that said pins are tied together. Feedback Input. FB senses the output voltage to regulate that voltage. Drive FB with a resistive voltage divider from the output voltage. The feedback reference voltage is 0.8V. See Setting the Output Voltage. Compensation Node. COMP is used to compensate the regulation control loop. Connect a series RC network from COMP to GND to compensate the regulation control loop. In some cases, an additional capacitor from COMP to GND is required. See Compensation Components. Enable Input. EN is a digital input that turns the regulator on or off. Drive EN higher than 2.7V to turn on the regulator, drive it lower than.v to turn it off. Pull up to the IN pin with 00kΩ resistor for automatic startup. Soft-start Control Input. SS controls the soft-start period. Connect a capacitor from SS to GND to set the soft-start period. See Soft-Start Capacitor. MP2303 Rev. 0.92 www.monolithicpower.com 4

TYPICAL PERFORMANCE CHARACTERISTICS V IN = 2V, V O = 3.3V, L = 0µH, C = 0µF, C2 = 22µF x 2, T A = 25 C, unless otherwise noted. Efficiency vs Feeback Voltage vs. Load Current Temperature EFFICIENCY (%) 95 90 85 80 75 70 65 60 55 50 VIN = 2V VIN = 24V = 2.5V 0 0.5.0.5 2.0 2.5 3.0 3.5 LOAD CURRENT (A) MP2303-EC02 FEEDBACK VOLTAGE (V) 0.80 0.805 0.800 0.795 0.790 0.7850 VIN = 2V VIN = 28V VIN = 4.75V 0.780-40 -20 0 20 40 60 80 TEMPERATURE ( o C) MP2303-TPC0 4.5 UVLO Rising vs. Temperature 2.70 Enable Lockout Threshold vs. Temperature 345 Oscillator Frequency UVLO THRESHOLD (V) 4.4 4.3 4.2 4. 4.0 3.9 3.8 2.35 3.7 2.30 325-40 -20 0 20 40 60 80-40 -20 0 20 40 60 80 TEMPERATURE ( o -40-20 0 20 40 60 80 C) TEMPERATURE ( o C) TEMPERATURE ( o C) MP2303-TPC02 ENABLE VOLTAGE (V) 2.65 2.60 2.55 2.50 2.45 2.40 MP2303-TPC03 FREQUENCY (KHz) 340 335 330 MP2303-TPC04 MP2303 Rev. 0.92 www.monolithicpower.com 5

TYPICAL PERFORMANCE CHARACTERISTICS (continued) V IN = 2V, V O = 3.3V, L = 0µH, C = 0µF, C2 = 22µF x 2, T A = 25 C, unless otherwise noted. Power Off through Enable V IN = 24V, V OUT = 3.3V, I OUT = 2A V OUT V/div. V OUT V/div. I L A/div. V EN 5V/div. I L A/div. V SW 0V/div. 4ms/div. MP2303-TPC05 MP2303-TPC06 Steady State Test V IN = 2V, V OUT = 3.3V, I OUT = A Load Transient Test V IN = 24V, V OUT = 3.3V, I OUT = 0A-A step with C FF = 470pF Short Circuit Protection V IN = 24V, V OUT = 3.3V, I OUT = 0A V IN 200mV/div. I L 500mA/div. V COMP 200mV/div. V OUT 00mV/div. V OUT V/div. V COMP V/div. V OUT AC Coupled 0mV/div. I L A/div. V SW 20V/div. I L 2A/div. MP2303-TPC07 MP2303-TPC08 MP2303-TPC09 MP2303 Rev. 0.92 www.monolithicpower.com 6

OPERATION FB 0.95V 0.3V -- -- OVP OSCILLATOR 340KHz RAMP CLK -- S CURRENT SENSE AMPLIFIER Q -- 5V IN BS SS 0.8V -- ERROR AMPLIFIER R Q CURRENT COMPARATOR SW COMP EN -- 2.5V.5V -- EN OK LOCKOUT COMPARATOR SHUTDOWN COMPARATOR.2V Figure Functional Block Diagram OVP IN < 4.05V IN INTERNAL REGULATORS GND MP2303_BD0 The MP2303 is a synchronous rectified, current-mode, step-down regulator. It regulates input voltages from 4.75V to 28V down to an output voltage as low as 0.8V, and supplies up to 3A of load current. The MP2303 uses current-mode control to regulate the output voltage. The output voltage is measured at FB through a resistive voltage divider and amplified through the internal transconductance error amplifier. The voltage at COMP pin is compared to the switch current measured internally to control the output voltage. The converter uses internal N-Channel MOSFET switches to step-down the input voltage to the regulated output voltage. Since the high-side MOSFET requires a gate voltage greater than the input voltage, a boost capacitor connected between SW and BS is needed to drive the high-side gate. The boost capacitor is charged from the internal 5V rail when SW is low. When the MP2303 FB pin exceeds 20% of the nominal regulation voltage of 0.8V, the over voltage comparator is tripped; the COMP pin and the SS pin are discharged to GND, forcing the high-side switch off. MP2303 Rev. 0.92 www.monolithicpower.com 7

APPLICATIONS INFORMATION COMPONENT SELECTION Setting the Output Voltage The output voltage is set using a resistive voltage divider from the output voltage to FB pin. The voltage divider divides the output voltage down to the feedback voltage by the ratio: R2 VFB = R R2 Thus the output voltage is: R R2 V OUT = 0.8 R2 Where V FB is the feedback voltage and V OUT is the output voltage. A typical value for R2 can be as high as 00kΩ, but a typical value is 0kΩ. Using that value, R is determined by: R = 2.5 ( 0.8)(kΩ) For example, for a 3.3V output voltage, R2 is 0kΩ, and R is 3.3kΩ. Inductor The inductor is required to supply constant current to the output load while being driven by the switched input voltage. A larger value inductor will result in less ripple current that will result in lower output ripple voltage. However, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. A good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% of the maximum switch current limit. Also, make sure that the peak inductor current is below the maximum switch current limit. The inductance value can be calculated by: V OUT L = f S I VIN Where V IN is the input voltage, f S is the 340KHz switching frequency, and I L is the peak-topeak inductor ripple current. Choose an inductor that will not saturate under the maximum inductor peak current. The peak inductor current can be calculated by: V I LP = ILOAD 2 fs L V Where I LOAD is the load current. OUT Optional Schottky Diode During the transition between high-side switch and low-side switch, the body diode of the lowside power MOSFET conducts the inductor current. The forward voltage of this body diode is high. An optional Schottky diode may be paralleled between the SW pin and GND pin to improve overall efficiency. Table 2 lists example Schottky diodes and their Manufacturers. Table 2 Diode Selection Guide Part Number Voltage/Current Rating Vendor B30 30V, A Diodes, Inc. SK3 30V, A Diodes, Inc. MBRS30 30V, A International Rectifier Input Capacitor The input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low ESR capacitors for the best performance. Ceramic capacitors are preferred, but tantalum or low-esr electrolytic capacitors may also suffice. Choose X5R or X7R dielectrics when using ceramic capacitors. Since the input capacitor (C) absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: I C = I LOAD V V OUT IN V V IN OUT IN The worst-case condition occurs at V IN = 2V OUT, where: I C = I LOAD 2 MP2303 Rev. 0.92 www.monolithicpower.com 8

MP2303 3A, 28V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER For simplification, choose the input capacitor whose RMS current rating greater than half of the maximum load current. The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.µF, should be placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. The input voltage ripple caused by capacitance can be estimated by: ILOAD V OUT V = OUT V IN fs C VIN VIN Output Capacitor The output capacitor is required to maintain the DC output voltage. Ceramic, tantalum, or low ESR electrolytic capacitors are recommended. Low ESR capacitors are preferred to keep the output voltage ripple low. The output voltage ripple can be estimated by: V OUT = RESR f S L VIN 8 fs C2 Where C2 is the output capacitance value and R ESR is the equivalent series resistance (ESR) value of the output capacitor. In the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated by: V OUT V OUT = 2 8 fs L C2 VIN In the case of tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For simplification, the output ripple can be approximated to: V OUT = RESR fs L VIN The characteristics of the output capacitor also affect the stability of the regulation system. The MP2303 can be optimized for a wide range of capacitance and ESR values. Compensation Components MP2303 employs current mode control for easy compensation and fast transient response. The system stability and transient response are controlled through the COMP pin. COMP pin is the output of the internal transconductance error amplifier. A series capacitor-resistor combination sets a pole-zero combination to control the characteristics of the control system. The DC gain of the voltage feedback loop is given by: VFB A VDC = RLOAD GCS A VEA Where A VEA is the error amplifier voltage gain, 400V/V; G CS is the current sense transconductance, 7.0A/V; R LOAD is the load resistor value. The system has 2 poles of importance. One is due to the compensation capacitor (C3) and the output resistor of error amplifier, and the other is due to the output capacitor and the load resistor. These poles are located at: GEA fp = 2π C3 A VEA fp2 = 2π C2 RLOAD Where, G EA is the error amplifier transconductance, 820µA/V, and R LOAD is the load resistor value. The system has one zero of importance, due to the compensation capacitor (C3) and the compensation resistor (R3). This zero is located at: f Z = 2π C3 R3 The system may have another zero of importance, if the output capacitor has a large capacitance and/or a high ESR value. The zero, due to the ESR and capacitance of the output capacitor, is located at: f ESR = 2π C2 R ESR MP2303 Rev. 0.9 www.monolithicpower.com 9

In this case, a third pole set by the optional compensation capacitor (C6) and the compensation resistor (R3) is used to compensate the effect of the ESR zero on the loop gain. This pole is located at: f P 3 = 2π C6 R3 The goal of compensation design is to shape the converter transfer function to get a desired loop gain. The system crossover frequency where the feedback loop has the unity gain is important. Lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system instability. A good rule of thumb is to set the crossover frequency to approximately one-tenth of the switching frequency. Switching frequency for the MP2303 is 340KHz, so the desired crossover frequency is 34KHz. Table 3 lists the typical values of compensation components for some standard output voltages with various output capacitors and inductors. The values of the compensation components have been optimized for fast transient responses and good stability at given conditions. Table 3 Compensation Values for Typical Output Voltage/Capacitor Combinations V OUT L C2 R3 C3 C6.8V 4.7µH 00µF 5.6kΩ 5.6nF None Ceramic 2.5V 4.7µH - 6.8µH 3.3V 6.8µH - 0µH 5V 0µH - 5µH 2V 5µH - 22µH 47µF Ceramic 3.65kΩ 8.2nF None 22µFx2 Ceramic 22µFx2 Ceramic 22µFx2 Ceramic.8 4.7µH 00µF/00mΩ SP-CAP 2.5V 4.7µH - 6.8µH 3.3V 6.8µH - 0µH 5V 0µH - 5µH 2.5V 4.7µH - 6.8µH 3.3V 6.8µH - 0µH 5V 0µH - 5µH 2V 5µH - 22µH 47µF SP-CAP 47µF SP-CAP 47µF SP CAP 560µF Al. 30mΩ ESR 560µF Al. 30mΩ ESR 470µF Al. 30mΩ ESR 220µF Al. 30mΩ ESR 4.42kΩ 4.7nF None 6.98kΩ 3.3nF None 6.5kΩ.8nF None 8.4kΩ 2.2nF None 5.6kΩ 3.3nF None 6.8kΩ 2.2nF None 0kΩ 2.2nF None 0kΩ 2nF.8nF 0kΩ 0nF.5nF 5kΩ 8.2nF nf 5kΩ 0nF 390pF MP2303 Rev. 0.92 www.monolithicpower.com 0

To optimize the compensation components for conditions not listed in Table 2, the following procedure can be used.. Choose the compensation resistor (R3) to set the desired crossover frequency. Determine the R3 value by the following equation: 2π C2 fc V R 3 = G G V EA CS OUT Where f C is the desired crossover frequency, 34KHz. 2. Choose the compensation capacitor (C3) to achieve the desired phase margin. For applications with typical inductor values, setting the compensation zero, f Z, below one forth of the crossover frequency provides sufficient phase margin. Determine the C3 value by the following equation: 4 C3 > 2π R3 f C FB Soft-Start Capacitor To reduce input inrush current during startup, a programmable soft-start is provided by connecting a capacitor (C4) from pin SS to GND. The soft-start time is given by: 0.8V t SS = C4 6µ A To reduce the susceptibility to noise, do not leave SS pin open. Use a capacitor with small value if you do not need soft-start function. External Bootstrap Diode It is recommended that an external bootstrap diode be added when the system has a 5V fixed input or the power supply generates a 5V output. This helps improve the efficiency of the regulator. The bootstrap diode can be a low cost one such as IN448 or BAT54. 5V 3. Determine if the second compensation capacitor (C6) is required. It is required if the ESR zero of the output capacitor is located at less than half of the 340KHz switching frequency, or the following relationship is valid: 2π C2 R f < 2 S ESR If this is the case, then add the optional compensation capacitor (C6) to set the pole f P3 at the location of the ESR zero. Determine the C6 value by the equation: C2 R C6 = R3 ESR BS MP2303 0nF SW MP2303_F02 Figure 2 External Bootstrap Diode This diode is also recommended for high duty cycle operation ( >65%) and high output VIN voltage (V OUT >2V) applications. MP2303 Rev. 0.92 www.monolithicpower.com

TYPICAL APPLICATION CIRCUITS INPUT 4.75V to 28V C5 0nF IN EN SS GND MP2303 C6 (optional) BS SW FB COMP C3 8.2nF D B30 (optional) OUTPUT 2.5V 3A MP2303_F03 Figure 3 MP2303 with 2.5V Output, 47µF/6.3V Ceramic Output Capacitor INPUT 4.75V to 28V D2 C5 0nF IN EN MP2303 BS SW OUTPUT 3.3V/3A SS GND C6 (optional) FB COMP C3 4.7nF D B30 (optional) MP2303_F04 Figure 4 MP2303 with 3.3V Output, 47µF/6.3V Ceramic Output Capacitor MP2303 Rev. 0.92 www.monolithicpower.com 2

PACKAGE INFORMATION SOIC8N (EXPOSED PAD) PIN IDENT. 0.229(5.820) 0.244(6.200) NOTE 4 0.50(3.80) 0.57(4.000) 0.0075(0.9) 0.0098(0.249) NOTE 2 SEE DETAIL "A" 0.03(0.330) 0.020(0.508) 0.050(.270)BSC 0.0(0.280) 0.020(0.508) x 45o 0.053(.350) 0.068(.730) NOTE 3 0.89(4.800) 0.97(5.000) 0.049(.250) 0.060(.524) 0.00(0.030) 0.004(0.0) SEATING PLANE 0 o -8 o 0.06(0.40) DETAIL "A" 0.050(.270).050.028 0.200 (5.07 mm) 0.40 (3.55mm) 0.060 Land Pattern NOTE: ) Control dimension is in inches. Dimension in bracket is millimeters. 2) Exposed Pad Option (N-Package) ; 2.3mm -2.79mm x 2.79mm - 3.8mm. Recommend Solder Board Area: 2.80mm x 3.82mm = 0.7mm 2 (6.6 mil 2 ) 3) The length of the package does not include mold flash. Mold flash shall not exceed 0.006in. (0.5mm) per side. With the mold flash included, over-all length of the package is 0.2087in. (5.3mm) max. 4) The width of the package does not include mold flash. Mold flash shall not exceed 0.0in. (0.25mm) per side. With the mold flash included, over-all width of the package is 0.77in. (4.5mm) max. MP2303 Rev. 0.92 www.monolithicpower.com 3

3mm x 3mm QFN0 NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP2303 Rev. 0.92 www.monolithicpower.com 4