isys-00 isys-00 isys-00 GUI interface - V. Power up LED blinking Sensor selftest Selftest passed YES LED flashes yellow NO LED blinking red object approaching YES LED flashes red NO object receding NO LED flashes yellow YES LED flashes green Measurement mode starts
isys-00 speed and distance sensor GUI description content start-up sequence. connecting the isys-00 to your PC. installing isys-00 GUI. start screen. Live Stream. Save - Load configuration. frequency channels 7 7. option Raw Signal 7. tab Detection 7 9. automatic amplification 0. output signals -. target filter options 9. output configuration 9. manual amplification 0. record & playback 0. GUI setting 0. Change RS address 7. Change RS /RS baudrate. Firmware contact information - Experience and Reliability in Radar-Technology
GUI description isys-00 speed and distance sensor isys-00 GUI - description The isys-00 GUI can be used to configure and display the measured signals of an isys-00 radar sensor. It displays the target list, FFT magnitude with threshold and the signal raw data. Experience and Reliability in Radar-Technology -
isys-00 speed and distance sensor GUI description start-up sequence The integrated LED indicates the status of the sensor on power up. Power up LED blinking Sensor selftest Selftest passed YES LED flashes yellow Measurement mode starts NO LED blinking red object approaching YES LED flashes red NO object receding YES LED flashes green NO LED flashes yellow - Experience and Reliability in Radar-Technology
GUI description isys-00 speed and distance sensor. connecting the isys-00 to your PC To connect the isys-00 with your PC use the following configuration (complete cables can be purchased from InnoSenT). M M 9 M M 9 Input isys-00 Pin # Signal Pin # OUT Pin # Output Input Pin # SignalOUT OUTOUT Output OUT VCC OUTGND VCC not connected RS GND GND RS 7 not connected RS_Rx GND RS_Tx 7 RS_Rx RS_Tx RS-Connector RS-Connector isys-00 / isys-00 Signal Pin # OUT OUT OUT VCC GND RSRS RS RSRS GND RS RS 7 RS_A RS RS RS_B RS 7 7 Input Output Pin # not connected Connector A-type compatible to SACC-M-SCO PLUG (PN: 9) from Phoenix Contacts The sensor has a RS or RS interface (depending on sensor-type). An isys-00 with RS interface can be connected directly to the COM port of the PC otherwise there can be a RS to USB adapter used. The Adapter installs a virtual COM port which can be selected in the GUI.. installing isys-00 GUI Software is available @ www.innosent.de (Service -> Downloads) Copy installer isys00x_gui_setup to your harddisk. Double-click on isys00x_gui_setup to start SetupWizard. Follow instructions. Click Finish to close setup and to launch GUI. Experience and Reliability in Radar-Technology -
isys-00 speed and distance sensor GUI description. start screen After launching the GUI the start screen apears. To connect the isys-00 sensor to the GUI click COM Port Config select your COM-Port set baud rate set device address (default=) click Connect click Close click to configure COM Port During the connection process the GUI reads some parameters from the Sensor. The red lamp in the connection window switches to green if successfull. Default baud rates: isys-00 isys-00 isys-00 select COM-Port set baud rate to 000 00 Baud 00 Baud 9 00 Baud click to connect The device address is only for RS communication interface required. Adapt this address in case of RS interface to the devices address you want to connect.. Live Stream A click on Start Live Stream starts displaying the live data in the opened tab.. Freeze/Run For an improved analysis of the sensor data, the display can be frozen by clicking on Freeze. To enable the live data again click on Run... Write all Params tp EEProm This command writes all data into the EEPROM. This command is mandatory after setting all your parameters, otherwise all configurations made are lost.. Save - Load configuration Short Range.ipf To configure more than one sensor with the same settings all parameters can be saved in an *.ipf file.. Save configuration to file By clicking on File => Save configuration to file the actual parameters will be saved in an *.ipf file... Load configuration from file By clicking on File => Load configuration from file parameter sets can be loaded. To write these parameters to the sensor click on Write all parameters to EEProm otherwise the settings are lost after shutdown the sensor. The Standard configuration is the Short Range parameter set (compare table beside). Other parameters sets are available @ www.innosent.de click to start Live View output approaching & receding active low, if object exist active high, if NO object exist output approaching active high, if object exist active low, if NO object exist output receding active high, if object exist active low, if NO object exist rising delay falling delay 7ms 7ms filter type highest amplitude single target filter 0% for all outputs amplification 0dB distance range 0...0m detection level 0dB - Experience and Reliability in Radar-Technology
GUI description isys-00 speed and distance sensor. frequency channels To avoid interferences if two sensors are mounted close to each other different frequency channels can be selected. click Config select use channel or use channel for using the sensor in Europe select use channel or use channel for using the sensor in the US Channel is corresponding to a transmit frequency of.90ghz Channel is corresponding to a transmit frequency of.0ghz Channel is corresponding to a transmit frequency of.ghz Channel is corresponding to a transmit frequency of.ghz 7. option Raw Signal The Option Raw Signals can be used to view the analog received signals. The raw signals tab shows the signal raw data which sampled by the analog to digital converter. Alternatively the user can switch to the FFT signal (Tab Detection ). The FFT and threshold are calculated by the sensor.. tab Detection This tab shows the FFT and the threshold calculated by the radar sensor. The threshold consists of three parts: adaptive value, height of the threshold depending on the noise level low-pass filter, for the frequency selection of the different objects user defined threshold value, will be added to the threshold.. User defined threshold values If the adaptive calculated threshold is lower than the minimum value it is set to the minimum. Change the sensitivity to vary the number of detections. Set these values by adjusting the slider or by setting the level in db... Linefilter By activating the Line Filters several frequencies can be cancelled. This can be used for example to prevent interference from fluorescent lamps. Experience and Reliability in Radar-Technology - 7 7
isys-00 speed and distance sensor GUI description 9. automatic amplification An automatic amplification can be activated in Config => Amplification. If the radar signals does not exceed the inner threshold (orange area), the signal will be increased. If the radar signal exceeds the inner threshold, but does not exceed the outer threshold (green area), nothing happens to the signal amplification (signal is inside hysteresis). If the radar signal exceeds the outer thershold, the signal amplification will be decreased. 0. output signals - The isys-00 offers output signals that can be activated and configured indepentendly of each other. The tabs Output, Output and Output shows the different target lists. Each target list has separate filter parameters which can be changed in the specific output tab. During a live stream a coloured button shows the actual status of the detected object: Green object is receding Red object is approaching Orange no object detected The output can filtered by the Target Filter Type menu. Possible settings are: activate / deactivate target filter smoothing level highest Amplitude mean velocity mean range median velocity median range The selection of the wanted option has a direct influence to the signals in the GUI as well as on the Output Configuration. Show Histogram By activating the Histogram option you can follow the time dependent trend of changes in speed and range of the object(s). - Experience and Reliability in Radar-Technology
GUI description isys-00 speed and distance sensor. target filter options The target filter options declare the velocity-, range- and signalarea within the sensor is able to detect objects. Velocity has an additional option to set the sign of the velocity to detect only receeding or approaching objects. The filters can be set in the following range: isys-00 isys-00/ isys-00 Speed range: Distance range : Distance range : Signal Level: 0...0km/h 0...0m 0...0m 0...0dB Speed range: Distance range : Distance range : Signal Level: 0...0km/h 0...0m 0...0m 0...0dB. output configuration To configure the output signals go to menu isys => Output Configuration The output PINs can be activated and configured seperately from each other. Possible setting of output type are: digital pwm (velocity) pwm (range) In case of pwm a pulse-width modulated signal will be send to the output PINs corresponding to the speed or range of the objects (depending on which option is selected) Output PIN configuration: configuration description target detected output pin state active low - normally open low side switch yes high impedance active low - normally open low side switch no connected to GND active low - normally closed low side switch yes connected to GND active low - normally closed low side switch no high impedance active high - normally open high side switch no high impedance active high - normally open high side switch yes connected to VCC active high - normally closed high side switch no connected to VCC active high - normally closed high side switch yes high impednace totem pole - normally open push-pull no connected to GND totem pole - normally open push-pull yes connected to VCC totem pole - normally closed push-pull no connected to VCC totem pole - normally closed push-pull yes connected to GND Experience and Reliability in Radar-Technology - 9 9
isys-00 speed and distance sensor GUI description. manual amplification The isys-00 sensor features a variable IF amplification with an Bit digital potentiometer. For changing the amplification, open the slider window in the Config menu under Amplification. The button Store stores all actual set parameters including the amplification into the devices EEPROM. The figures beside are showing the amplification for the different potentiometer positions.. record & playback The isys-00 radar sensor features a record & playback functionality for raw data, fft & threshold and Targetlist. Depending on the active tab the specific data is recorded. record: Start recording with record button. Stop recording with stop button and chose file name and storage location. A filename including date and time is suggested. playback: Open playback window with play button. After opening a recoded file (xx.log) the playback can be started. Set the playback speed by adjusting the cycle time.. GUI setting Open in the GUI setting window in the Config menu. Change the units as useful for the measurements. 0 0 - Experience and Reliability in Radar-Technology
GUI description isys-00 speed and distance sensor. Change RS address Changing RS address is a special feature of the isys-00 and isys-00. Open the slider window in the Help menu under About. Set the new device address and click set. After changing the device address the command acknowledge is send with the new device address. Note: The address is written directly to the EEPROM. 7. Change RS / RS baudrate The isys-00 sensor supports different baudrates. For changing the baudrate, open the slider window in the Config menu under Change Baudrate. Select new baudrate in dropdown menu and click Change Baudrate. Note: The baudrate is written directly to the EEPROM. Experience and Reliability in Radar-Technology -
isys-00 speed and distance sensor GUI description. Firmware. firmware update menue To start the firmware update go to menue Help => about. sensor/gui information () Information about the actual sensor firmware and GUI software. firmware update () To start the firmware update select update () select new firmware version (*.hex - file) () confirm with button flash firmware () wait until progress bar reaches 00% () () () - Experience and Reliability in Radar-Technology
GUI description isys-00 speed and distance sensor contact information If you have any questions please contact us! Corinna Mergenthal Tel.: +9-9-9- E-Mail: corinna.mergenthal@innosent.de Martin Maidhof Tel.: +9-9-9- E-Mail: martin.maidhofl@innosent.de part numbers P/N: isys-00 P/N: isys-prog_adap Experience and Reliability in Radar-Technology - P/N: isys-pow_adap P/N: isys-pow_sup
Contact Details: Tel: +9-9-9-0 E-Mail: info@innosent.de www.innosent.de