Sheet Stock Options s, & Wood with Resin Back (Non Adhesive) Lb/Sq.Ft. =.194 Wood With Wood Back (Non Adhesive) Lb/Sq.Ft. =.123 Wood with Paper Back (Non Adhesive) Lb/Sq.Ft. =.106 Wood with Wood Back (A - Peel & Stick) Lb/Sq.Ft. =.177 Wood with Paper Back (A - Peel & Stick) Lb/Sq.Ft. =.148 Sheet ore Lb/Sq.Ft. =.460 Sheet ore Lb/Sq.Ft. =.739 Sheet ore Lb/Sq.Ft. =.934 Sheet ore Lb/Sq.Ft. =.934 Sheet ore Lb/Sq.Ft. =.448 ½" ore Lb/Sq.Ft. = 1.788 ½" ore Lb/Sq.Ft. = 1.220 ⅝" ore Lb/Sq.Ft. = 2.502 ⅝" ore Lb/Sq.Ft. = 1.647 11 /16" ombi-ore Lb/Sq.Ft. = 2.257 Sheet Stock & Panel Descriptions Sheet Stock Wood veneer with a resin soaked backer sheet that has been permanently bonded under heat and pressure. This provides the sheet with dimensional stability, strength and flexibility and acts as a barrier to prevent adhesives and finishes from penetrating. an be used with a solvent based or water based contact adhesive. Resin backed veneers are also sometimes referred to as DuraBack, PolyBak, or PolyLam. Wood with a wood back suitable for use with contact adhesive. Wood with a paper back suitable for use with contact adhesive. 2 Ply sheet stock that provides the look of solid wood plus 3M Peel and Stick adhesive. Wood with a paper back plus 3M Peel and Stick adhesive. Sheet Stock A Face grade wood veneer, 3 ply veneer core with a #4 back. The #4 back may be a different wood species than the A face. A Face grade wood veneer, core with a #4 back. The #4 back may be a different wood species than the A face. Sheet Stock A Face grade wood veneer, core with a #1 back. A Face grade wood veneer, core with a #4 back. The #4 back may be a different wood species than the A face. A or B Face grade wood veneer, veneer core with various grade backs. ½" Sheet Stock A Face grade wood veneer, core with a #1 back. A Face grade wood veneer, veneer core with a #1 back. ⅝" Sheet Stock A Face grade wood veneer, core with a #1 back. A Face grade wood veneer, veneer core with a #1 back. 11 /16" ombi-ore ombi-core has veneer core inner plies with crossbands. This material offers similar strength and stability to veneer core but has the void-free surface quality of. Also available in ustom Pressed Options, see Section.4. Sheet Stock ore Lb/Sq.Ft. = 2.897 AA, A or B Face grade wood veneer, core with a #1 back. ore Lb/Sq.Ft. = 1.833 A Face grade wood veneer, veneer core with a #1 back. Note: All veneers are book matched on the face side, with the exception of Hickory, all Rustic and notty Grades..1.2 For PRIING See Section.1 in our Wholesale Pricing atalog. (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667
s, & Sheet Stock Options Slicing Methods Rotary ut Plain Sliced Rift ut The log is turned against a razor sharp blade, like unwinding a roll paper. This cut produces a wide veneer with a bold variegated pattern. ½ of a log is held heart side against the table. Slicing is done parallel to the center line of the log. This cut produces cathe dral grain. Slicing is done across the growth rings to produce a straight grain look. Sometimes flake is present in oak due to the Medullary ray cells. Slicing is done at a 15 angle across the growth rings to produce a straight grain look without flake. nife Book Match Book Match: The most common matching type. Alternating leaves are turned over, so that adjacent leaves are opened like the pages of a book. Visual Effect: joints match, creating a symmetrical pattern. Yields maximum continuity of grain. Prominent characteristics ascend or descend across the face. *Walzraft offers all veneers as being Book Matched. For PRIING See Section.1 in our Wholesale Pricing atalog. 99.7% American Made.1.3
Sheet Stock Options s, & SS = Rough ut to Stock Sizes (Only) RTRW = Rip to Rough Width PTS = Precision ut to Size ut and Ripped Descriptions A sheet that is only available in the following sizes: : 4'x8', 2'x8', 4'x4', 2'x4', 24"x32"., 7 /32",, ⅜", ½", ⅝", 11 /16",, 1" Panels: 4'x8', 2'x8', 4'x4', 2'x4', 24"x32". HDF, ⅞" Panels: 60"x96", 30"x96", 60"x48", 30"x48". 7 /32" Raw : 60"x108", 30"x108", 60"x54", 30"x54". 12.0mm, 15.2mm and 18.0mm Panels: 60"x60". Edges may need to be trimmed. Some sheets may be slightly oversized. See the chart below for the actual size of our Sheet Stock materials. Allow per saw kerf. Available in customer specified widths x 8' long only (60" long for 12.0mm, 15.2mm & 18.0mm thick panels). Edges may need to be trimmed. Specified widths will not be oversized. Some lengths may be slightly oversized. See the chart below for the actual size of our Sheet Stock materials. Allow per saw kerf. Available in customer specified widths and lengths (any size piece that the sheet will yield). PTS items will be square and the exact size ordered. Pieces will not be oversized. Edges will be a sawn edge, not a routed edge, and as such could have visible saw kerfs. Precision ut to Size sheet stock is 100% free from defect on the face of the part. Finished sizes include cuts to both the width and the height. See the chart below for the actual size of our Sheet Stock materials. Allow per saw kerf. Actual Size of Sheet Stock lass Description Actual Size of Sheet 2'x8' sheets are cut from 4'x8' Resin Back 48½" x 96½" sheets. We split the sheet Non Adhesive Wood Back 48½" x 96⅜" equally in two halves to produce two slightly oversized Paper Back 49" x 97" 2x8 s. * Pressure Sensitive Adhesive (A), Raw HDF Wood Back 48½" x 96⅜" * A (Peel & Stick) will cover the entire Paper Back 49" x 97" length of the sheet, but may not extend to the edges in width. ore 48½" x 96½" ore A4 96½" x 48½" ( Not used for oversized 2'x8', 4'x4' and 2'x4' panels.) ore A1 48½" x 96½" ore A4 48½" x 96½" ore 48½" x 96½" ½" ore A1 48½" x 96½" ½" ore 48½" x 96½" ⅝" ore A1 48½" x 96½" ⅝" ore 48½" x 96½" ore A1 48½" x 96½" ore 48½" x 96½" 7 /32 ",, ⅜", ½", ⅝" 11 /16",, 1" 49" x 97" 4'x4' sheets are cut from 4'x8' sheets. We split the sheet equally in 2 halves to produce two slightly oversized 4x4 s. (This is only available with material and veneer.) 2'x4' sheets are cut from 4'x8' sheets. We split the sheet equally in 2 halves in both width and height to produce four slightly oversized 2x4 s. (This is only available with material & veneer.) If you are ordering 2'x4', 4'x4', 2'x8' or 4'x8' sheets, you will be charged for that square footage but will receive slightly oversized panels. ⅞" 61" x 97" The same rules apply as 7 /32" 61" x 109" above when cutting the High Density 5'x8' or 5'x9' panels in halves or 61" x 97" Fiberboard quarters..1.4 For PRIING See Section.1 in our Wholesale Pricing atalog. (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667
s, & Sheet Stock Options (Standard) One-Sided (1S) Finish - Sheet Stock Products Non-Adhesive Resin Back.037" [0.9mm] +.008"/-.007" ore, A1.220" [5.6mm] +/-.005" Non-Adhesive Wood Back.036" [0.9mm] ore, A4.220" [5.6mm] +/-.005" (8'x4') Non-Adhesive Paper Back.023" [0.6mm] A Paper Back.023" [0.6mm] ore, A4.220" [5.6mm] +/-.005" Drawer Box Bottom See Finish Options notes within this section for more information. A Wood Back.036" [0.9mm] ore A or B Face.198" [5.0mm] +/-.012" Various Grade Backs ore, A4.156" [4.0mm] 7 /32".219" [5.6mm] +/-.015" ore, A4.165" [4.2mm] +/-.010" ore, A4.165" [4.2mm] +/-.010" (8'x4') MEDEX.250" [6.4mm] +/-.015" HDF.125" [3.2mm] +/-.015" (5'x8') ⅜".375" [9.5mm] +/-.015" ½" ore, A1.500" [12.7mm] +0"/-.015" ¹¹/16" ombi-ore.687" [17.4mm] ½" ore, A1.500" [12.7mm] +0"/-4.6875" ¹¹/16".687" [17.4mm] (Standard) Two-Sided (2S) Finish - Sheet Stock Products ½".500" [12.7mm] +/-.015" 18.0mm ore.709" +.03"/-.04" ore AA Face +0"/-.015" Door Grade See Finish Options notes within this section for more information. 12.0mm ore.4724" +.02"/-.03" ore A or B Face +0"/-.015" #1 Grade Back ⅝" ore, A1.625" [15.9mm] +0"/-.015" ore, A1 ⅝" ore, A1.625" [15.9mm] ⅝".625" [15.9mm] +/-.015" ⅞".875" [22.2mm] 15.2mm ore.598" +.02"/-.03" 1" 1.00" [25.4mm] For PRIING See Section.1 in our Wholesale Pricing atalog. 99.7% American Made.1.5
Sheet Stock Options s, & Ordering & Pricing Notes:, & Ordering Guidelines 1 Order Forms Please use Sheet Goods Order Forms (E Z Forms #8, #8.2) and part #185. Pricing 1 Pricing Please see Section.1 of the Wholesale Pricing atalog. 1 Refacing with SolidTone Finish/olor 2 1 Refacing with SolidTone WoodGrain Finish/olor 1 Shipping 1 One Sided (1S) Finishing 2 Two-Sided (2S) Finishing utting Prefinished s 2 Application Instructions Technical Notes:, & abinet Refacing Options (hapter U) Sheet Stock options available for refacing with SolidTone Finish/olor: Non-Adhesive Resin Back and A (Peel & Stick) Wood Back HDF and, 7 /32" & & ( ore and ore) Note: When applying a SolidTone Finish/olor to A (Peel & Stick) Wood Back, the only SS that are available will be 2' x 8' [609.6mm x 2438.4mm], 2' x 4' [609.6mm x 1219.2mm] and 24" x 32" [609.6mm x 812.8mm]. Sheet Stock options available for refacing with SolidTone WoodGrain Finish/olor: Non-Adhesive Resin Back & A (Peel & Stick) Wood Back and ( ore and ore) Note: When applying a SolidTone WoodGrain Finish/olor to A (Peel & Stick) Wood Back, the only SS that are available will be 2' x 8' [609.6mm x 2438.4mm], 2' x 4' [609.6mm x 1219.2mm] and 24" x 32" [609.6mm x 812.8mm]. General Information (hapter A) PM18 (U-hannel Box) will be Walzraft's preferred method of packaging sheet stock thick or greater, unless otherwise specified. Finish Options (hapter R) and, 7 /32", & ⅜", HDF and are only finished on the face of the panel (1S). Minimal over spray onto the edges and back of product will be considered acceptable. ½", ⅝", 11 /16",, ⅞" and 1" & is finished on the face and back of the panel only (2S). Minimal over spray onto the edges of the product will be considered acceptable. A 2S finish for these products is recommended and is Walzraft s standard method as it helps to balance the product and minimize warpage. With thicker material it is more difficult to correct warpage during installation or a product's ability to lay flat when it is not properly balanced. You may choose a 1S finish for these products, but minimal over spray onto the edges and back will be considered acceptable and there will be no warranty against warpage. If over spray is not acceptable, Walzraft can mask the edges and back during the finishing process, but additional charges will apply. If a 1S finish is desired for these products, please indicate this, and whether or not over spray is acceptable, in the Special Instructions section of the order form. Miscellaneous When cutting prefinished wood veneers, Walzraft recommends the use of some type of veneer saw, razor knife or trim router to produce a clean cut. We do not recommend the use of a laminate slitter on pre-finished wood veneers as this can sometimes leave a jagged edge. When choosing to use a laminate slitter, it is recommended that you cut the piece oversized, secure in place and then rout flush to produce a smooth, clean edge. Manufacturer s guidelines for suggested application will be provided with each order. Walzraft and its suppliers will warranty product, provided the material was properly installed. Sheet Stock Options (hapter ) 1 Edgebanding Please see Section L.1 - Basic abinet Box omponents for edgebanding sheet stock parts. Notes ontinued on Next Page....1.6 For PRIING See Section.1 in our Wholesale Pricing atalog. (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667
s, & Sheet Stock Options 1 4' x 8' Panels 2 8' x 4' Panels 1 Birch, herry, Pine, Hard & Soft Maple 2 Whole Piece Face (WPF) 3 Hickory - - Rustic Grade with a DBPB Technical Notes:, &...continued Sizes / Dimensions 4'x8' panels are considered 95% free from defect on the face of the product. If you require panels to be 100% free from defect on the face, please order Precision ut to Size (PTS). All materials originate from a 4'x8' sheet. ut to Size includes cuts to both the width and height. PTS items will be square and the exact size ordered. Pieces will not be oversized. Edges will be a sawn edge, not a routed edge, and as such could have visible saw kerfs. Rip to Rough Width (RTRW) and Rough ut to Stock Sizes (SS) would be 95% free from defect on the face, not 100% free. Both dimensions are not being cut to size. When Precision ut to Size (PTS) pieces of or, ore, A4 are ordered from 8' x 4' panels, widths must be over 48". Please order from a standard 4' x 8' sheet when widths are under 48". Wood Specie Options (hapter S) To minimize any color mismatch between veneer refacing materials and solid wood products for these wood species, Walzraft recommends using a Spray No Wipe stain process on the entire job, for a blotch free finish. Whole piece faces are made from veneer that has been rotary cut. A whole piece face veneer will not contain any splices. For some time Walzraft has been asked by customers to supply a more Rustic looking Hickory--Rustic veneer. Walzraft has always found this request difficult to fulfill in Hickory because during the veneer slicing process some knots are loosened and either completely or partially fall out. Recently, Walzraft became aware of a product that improves the appearance of sheets with missing knots. It does this by using a Dark Brown Paper Back (DBPB) on the veneer. Walzraft now offers Hickory--Rustic in Paperback Non-Adhesive, and in Paperback A (Pressure Sensitive Adhesive) using the Dark Brown Paper Backing (DBPB). This backing color is close to the color of the knots that one normally finds in Rustic Hickory, and helps to make any portion of a knot that is missing appear to be approximately the same color as the remaining knot. When ordering Hickory--Rustic in Paperback Non-Adhesive, and in Paperback A (Pressure Sensitive Adhesive), please note that it is considered normal to find knots of any size up to 1½" in diameter that may be completely missing, or partially missing. Many users consider this acceptable as the dark backer tends to still give the impression of a knot. Some users may consider the smaller missing knots acceptable, but will not use the portions of the sheet with larger knots. Some users will not find any missing knot acceptable; this material would be a poor choice for those customers. For PRIING See Section.1 in our Wholesale Pricing atalog. 99.7% American Made.1.7
Sheet Stock Options s, & HDF High Density Fiberboard Pressure Sensitive (3M A) Peel & Stick Non-Adhesive HDF.125" [3.2mm] (5'x8') ore, A4.165" [4.2mm] +/-.010" (8'x4') ore, A4.165" [4.2mm] +/-.010" ore, A4.156" [4.0mm] Wood Back.036" [0.9mm] Paper Back.023" [0.6mm] Paper Back.023" [0.6mm] Wood Back.036" [0.9mm] Resin Back.037" [0.9mm] +.008"/-.007" 8x4 Only SS Part #185 Availability harts SS = Rough ut to Stock Sizes (Only) - 4x8, 2x8, 4x4, 2x4, 24x32 HDF: 60x96, 30x96,60x48, 30x48-4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size (See Section.1 - Product Spec. atalog for ut/rip Size Descriptions) SS SS RTRW PTS SS SS SS SS RTRW PTS SS RTRW PTS PTS SS RTRW PTS Wood Speceis olor/grain Grade AFRORMOSIA X X X X X X X X X X X X X X X X X X X ALDER X X X X X X X X ANIGRE-MEDIUM FIGURE Mill Grade X X X Brown - X X X X X X X X X X X X ASH White - X X X Blond Flat Grain X X X BAMBOO Vertical Grain X X X aramelized Flat Grain X X X Vertical Grain X X X BEEH-EUROPEAN Steamed - X X X X X X Baltic - Mill Grade alico / Mixed - X X X X X X X X X X X X X X X - WPF X X X X X X X X X X X X X X X Red - BIH Red - White - X X X X X X X X X X X X X X X White - - WPF X X X X X X X X X BUTTERNUT No Sap - X X X X X X X X X X X X X X X Gummy Grade X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X HERRY Ultra X X X No Sap (Straight Grain) X X X YPRESS X X X ELM-RED Mill Grade Eucalyptus-Red Grandis X X X FIR-DOUGLAS Rift Sawn (Straight Grain) Reconstituted X X X HDF Raw Paint Grade X X X X X X X X X Brown - alico / Mixed - X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X** X** X X X HIORY Ultra White - X X X X X X JATOBA Mill Grade X X X ** = See Wood Species Options note on previous page..1.8 (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667
s, & Sheet Stock Options HDF High Density Fiberboard Pressure Sensitive (3M A) Peel & Stick Non-Adhesive HDF.125" [3.2mm] (5'x8') ore, A4.165" [4.2mm] +/-.010" (8'x4') ore, A4.165" [4.2mm] +/-.010" ore, A4.156" [4.0mm] Wood Back.036" [0.9mm] Paper Back.023" [0.6mm] Paper Back.023" [0.6mm] Wood Back.036" [0.9mm] Resin Back.037" [0.9mm] +.008"/-.007" Part #185 Availability harts SS = Rough ut to Stock Sizes (Only) - 4x8, 2x8, 4x4, 2x4, 24x32 HDF: 60x96, 30x96,60x48, 30x48-4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size (See Section.1 - Product Spec. atalog for ut/rip Size Descriptions) PTS SS RTRW PTS 8x4 Only SS SS SS RTRW PTS SS SS SS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade MAHOGANY Budget Grade MAHOGANY-GENUINE (HAYA) X X X X X X MAHOGANY-SIPO X X X (HAYA) X X X X X X X X X X X X X X X X X X MAHOGANY - SAPELE Birds Eye - X X X X X X urly - X X X X X X alico / Mixed - X X X X X X X X X X X X X X X X X X X X X X X X X X MAPLE - HARD X X X X X X X X X X X X X X X X X X X X X X (Straight Grain) X X X X X X Wormy Grade Raw Paint Grade Raw - MEDEX (NAUF) Paint Grade MAPLE - SOFT X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Ultra X X X X X X X X X X X X X X X X X X X X X X OA-RED X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Rift Sawn (Straight Grain) X X X X X X OA-WHITE X X X X X X Rift Sawn (Straight Grain) notty Grade X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X PINE-NORTHERN WHITE alico / Mixed - Green - X X X X X X White - POPLAR X X X X X X X X X X X X X X X X X X X X WALNUT No Sap - X X X X X X X X X X Architectural Grade s Please see Section.2. All Other Wood Species Please call for quote and availability. 99.7% American Made.1.9
Sheet Stock Options s, & ⅜" MEDEX 7 /32" ore A or B Face ore, A4 ore, A4 ore, A1 Part #185 Availability harts.219" [5.6mm].198" [5.0mm] +/-.012".220" [5.6mm] +/-.005".220" [5.6mm] +/-.005".220" [5.6mm] +/-.005" SS = Rough ut to Stock Sizes (Only) 4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size.375" [9.5mm].250" [6.4mm] (4'x8' or 5'x9') Various Grade Backs (8'x4') Drawer Box Bottom (See Section.1 - Product Spec. atalog for ut/rip Size Descriptions) PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS 8 x 4 Only SS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade AFRORMOSIA X X X X X X X X X ALDER ANIGRE-MEDIUM FIGURE Mill Grade Brown - X X X ASH White - Flat Grain Blond Vertical Grain BAMBOO aramelized Flat Grain Vertical Grain BEEH-EUROPEAN Steamed - X X X X X X Baltic - Mill Grade alico / Mixed - X X X X X X X X X X X - WPF X X X X X X Red - BIH Red - White - X X X X X X White - - WPF BUTTERNUT No Sap - X X X X X X X X X X X Gummy Grade X X X X X X X X X X X X X X X X X X X X X X Ultra X X X X X X HERRY X X X YPRESS ELM-red Red - Mill Grade eucalyptus-red grandis FIR-douglas (Straight Grain) Reconstituted HDF Raw Paint Grade No Sap (Straight Grain) X X X Brown - alico / Mixed - X X X X X X X X X X X X X X X X X X X X X X HIORY Ultra JATOBA Mill Grade White -.1.10 (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667
s, & Sheet Stock Options ⅜" MEDEX 7 /32" ore A or B Face ore, A4 ore, A4 ore, A1 Part #185 Availability hart.219" [5.6mm].198" [5.0mm] +/-.012".220" [5.6mm] +/-.005".220" [5.6mm] +/-.005".220" [5.6mm] +/-.005" SS = Rough ut to Stock Sizes (Only) 4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size.375" [9.5mm].250" [6.4mm] (4'x8' or 5'x9') Various Grade Backs (8'x4') Drawer Box Bottom (See Section.1 - Product Spec. atalog for ut/rip Size Descriptions) PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS 8x4 Only SS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade MAHOGANY Budget Grade X X X MAHOGANY-GENUINE (HAYA) X X X X X X MAHOGANY-SIPO (HAYA) MAHOGANY-SAPELE Birds Eye - urly - alico / Mixed - X X X X X X X X X X X X MAPLE-HARD X X X X X X X X X X X X X X X X (Straight Grain) Wormy Grade MAPLE-SOFT Raw Paint Grade X X X X X X Raw - MEDEX (NAUF) Paint Grade X X X X X X X X X X X X X X X X X X Ultra X X X X X X X X X X X X X X X X OA-RED X X X X X X X X X X X X Rift Sawn (Straight Grain) X X X X X X X X X X X X OA-WHITE X X X X X X Rift Sawn (Straight Grain) notty Grade X X X X X X X X X PINE-NORTHERN WHITE alico / Mixed - X X X Green - X X X White - POPLAR X X X X X X WALNUT No Sap - X X X All Other Wood Species Please see page.2.1. 99.7% American Made.1.11
Sheet Stock Options s, & Part #185 Availability harts 15.2mm ore ⅝" ⅝" ore, A1 ⅝" ore, A1 12.0mm ore ½" ½" ore, A1 ½" ore, A1 SS = Rough ut to Stock Sizes (Only) 4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size.1.12.598" +.02"/-.03".625" [15.9mm].625" [15.9mm].625" [15.9mm] +0"/-.015".472" +.02"/-.03".500" [12.7mm].500" [12.7mm].500" [12.7mm] +0"/-.015" (See Section.1 - Product Spec. atalog for ut/rip Size Descriptions) SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade AFRORMOSIA X X X ALDER X X X ANIGRE-MEDIUM FIGURE Mill Grade Brown - ASH White - Flat Grain Blond BAMBOO Vertical Grain Flat Grain aramelized Vertical Grain BEEH European Steamed - Baltic - Mill Grade X X X X X X alico / Mixed - X X X X X X X X X X X X - WPF Red - BIH Red - White - X X X X X X X X X X X X White - - WPF BUTTERNUT No Sap - X X X X X X X X X X X X Gummy Grade X X X X X X X X X X X X X X X X X X X X X X X X Ultra (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667 HERRY YPRESS ELM-RED Mill Grade EUALYPTUS-RED GRANDIS FIR-DOUGLAS (Straight Grain) Reconstituted HDF Raw Paint Grade No Sap (Straight Grain) Brown - alico / Mixed - X X X X X X Ultra HIORY White - JATOBA Mill Grade
s, & Sheet Stock Options Part #185 Availability harts 15.2mm ore ⅝" ⅝" ore, A1 ⅝" ore, A1 12.0mm ore ½" ½" ore, A1 ½" ore, A1 SS = Rough ut to Stock Sizes (Only) 4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size.598" +.02"/-.03".625" [15.9mm].625" [15.9mm].625" [15.9mm] +0"/-.015".472" +.02"/-.03".500" [12.7mm].500" [12.7mm].500" [12.7mm] +0"/-.015" (See Section.1 - Product Spec. atalog for ut/rip Size Descriptions) SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade MAHOGANY Budget Grade MAHOGANY-GENUINE (HAYA) MAHOGANY-SIPO (HAYA) MAHOGANY-SAPELE Birds Eye - urly - alico / Mixed - X X X X X X X X X X X X X X X X X X X X X X X X (Straight Grain) Wormy Grade Raw Paint Grade X X X X X X Raw - MEDEX (NAUF) Paint Grade MAPLE-HARD MAPLE-SOFT Ultra X X X X X X X X X X X X X X X X X X X X X X X X OA-RED Rift Sawn (Straight Grain) 99.7% American Made OA-WHITE X X X X X X Rift Sawn (Straight Grain) notty Grade PINE-NORTHERN WHITE alico / Mixed - Green - White - POPLAR WALNUT No Sap - All Other Wood Species Please call for quote and availability..1.13
Sheet Stock Options s, & 1" ⅞" ore, A1 ore A or B Face ore AA Face 18.0mm ore ¹¹/16" ¹¹/16" ombi-ore Part #185 Availability harts 1.00" [25.4mm].875" [22.2mm] +0"/-.015" +0"/-.015".709" +.03"/-.04".687" [17.4mm].687" [17.4mm] SS = Rough ut to Stock Sizes (Only) 4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size (5'x8') #1 Grade Back Door Grade (See Section.1 - Product atalog for ut/rip Size Desc.) SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade AFRORMOSIA X X X ALDER X X X ANIGRE-MEDIUM FIGURE Mill Grade Brown - ASH White - Flat Grain Blond Vertical Grain Flat Grain aramelized Vertical Grain BAMBOO BEEH-EUROPEAN Steamed - Baltic - Mill Grade X X X alico / Mixed - X X X X X X - WPF Red - BIH Red - White - X X X X X X White - - WPF BUTTERNUT No Sap - X X X X X X Gummy Grade X X X X X X X X X X X X Ultra HERRY No Sap (Straight Grain) YPRESS ELM-RED Mill Grade EUALYPTUS-RED GRANDIS FIR-DOUGLAS (Straight Grain) Reconstituted HDF Raw Paint Grade Brown - alico / Mixed - X X X X X X X X X X X X HIORY Ultra JATOBA Mill Grade White -.1.14 (Phone) 1-800-237-1326 6:00AM - 4:30PM ST (24 Hour Fax) 1-608-781-3667
s, & Sheet Stock Options 1" ⅞" ore, A1 ore A or B Face ore AA Face 18.0mm ore ¹¹/16" ¹¹/16" ombi-ore Part #185 Availability harts 1.00" [25.4mm].875" [22.2mm] +0"/-.015" +0"/-.015".709" +.03"/-.04".687" [17.4mm].687" [17.4mm] SS = Rough ut to Stock Sizes (Only) 4x8, 2x8, 4x4, 2x4, 24x32 PTS = Precision ut to Size (5'x8') #1 Grade Back Door Grade (See Section.1 - Product atalog for ut/rip Size Desc.) SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS SS RTRW PTS Wood Speceis olor/grain Grade MAHOGANY Budget Grade MAHOGANY-GENUINE (HAYA) Birds Eye - urly - alico / Mixed - MAHOGANY-SIPO (HAYA) MAHOGANY-SAPELE (HAYA) X X X X X X MAPLE-HARD X X X X X X X X X X X X X X X X X X X X X X X X (Straight Grain) Wormy Grade MAPLE-SOFT Raw Paint Grade X X X X X X X X X X X X X X X Raw - MEDEX (NAUF) Paint Grade X X X X X X X X X X X X X X X X X X Ultra X X X X X X X X X X X X notty Grade OA-RED Rift Sawn (Straight Grain) OA-WHITE Rift Sawn (Straight Grain) PINE-NORTHERN WHITE alico / Mixed - Green - White - POPLAR WALNUT No Sap - All Other Wood Species Please call for quote and availability. 99.7% American Made.1.15