PB 8328 WS 8328 JAMBOREE IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. ASSEMBLY INSTRUCTIONS Swing-N-Slide Printed in USA
DIMENSIONS STRUCTURE.
TOOLS REQUIRED DRILL HAMMER TAPE MEASURE PHILLIPS BIT CARPENTER SQUARE PLIERS INCLUDED HARDWARE Small Square Bit
HARDWARE 2 7 1 12 4 2 4 1 1 3 1 Small 7
SA6066 BOX 1 of 2 BOARD LIST
SA6065 BOX 2 of 2 BOARD LIST 9
COMPONENTS
STEP 1 Per Board Check to make sure structure is square PANEL A NOTE HOLES Install 30mm Screws With Heads ed To Board To Avoid Protrusions. Per Board PANEL B Per Board PANEL C Per Board
STEP 2 Per Board ALL BOARDS Check to make sure structure is square FLUSH Per Board PANEL D Per Board Per Board FLUSH Install 30mm Screws With Heads ed To Board To Avoid Protrusions. PANEL E FLUSH Per Board
STEP 3 Check to make sure structure is square PANEL C T-Nut Small NOTE HOLES to the bottom T-Nut Small NOTE: HOLE ORIENTATION FRAME A Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
STEP 4 FRAME A FLIP FRAME OVER
STEP 5 per Board This Side T-Nut Small NOTE HOLE per Board This Side NOTE: HOLE ORIENTATION T-Nut Small FRAME B Check to make sure structure is square WINDOW PANE INSTALL Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
STEP 6 FRAME B FLIP FRAME OVER
STEP 7 3 From Outside of Post PANEL A Check to make sure structure is square 3 From outside of post To end of horizontal support. PANEL A to outside edge of 3 x 3 PF 6338 to outside edge of 3 x 3 94-1/4 Side View of Tower FRAME A NOTE HOLE
STEP 8 FRAME A 3 From Outside of Post to End of Horizontal Support. Side View of Tower 19-1/2 FRAME B
STEP 9 per side Back of Tower per side NOTE: PRE-DRILL HOLES GOING INTO DECK SUPPORTS 55-1/4 11 11 Top View of Tower
STEP 10 per board per joint PANEL B PANEL B INSTALL
STEP 11 T-Nut Small 46-5/8
STEP 12 T-Nut Small HEADS FLUSH
STEP 13 Check to make sure structure is square NOTE HOLES 45 TO HOLE 46-5/8 PANEL E FRAME C FLIP FRAME OVER
STEP 14 T-Nut Small LIFT FRAME UP Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
STEP 15 Check to make sure structure is square FRAME C
STEP 16 Check to make sure structure is square per joint PANEL D Inside View of Tower 77-1/4
STEP 17 per board PRE-DRILL per board SUPPORTS 12-3/4 12-3/4 Top View of Terrace
STEP 18 per board
STEP 19 2-1/4
STEP 20 26
STEP 21 Loc Nut Attach Tower Beam Support Board as shown.
STEP 22 Swing Beam Large Hanger Beam Clamp 1 2 3 x4 Correct Orientation Screws 4 5
STEP 23 A-Frame SB Support A-Frame Small Small A-Frame Support Small
STEP 24 Bracket x2 x2
STEP 25 Beam Brace Small Barrier Boards Removed for Clarity
STEP 26 Carriage Bolt Small Barrier Boards Removed for Clarity
STEP 27 Screws CENTERED x2 Screws Screws x2 Screws Front View Screws Screws per board Screws Screws per board x2 NOTE: Overlap Shingles as shown.
STEP 28 TURN ROOF ASSEMBLY ON END. Screws per board per board Screws per board OUTSIDE TO OUTSIDE OUTSIDE TO OUTSIDE CENTER TO OUTSIDE 1-1/2 1-1/2 Screws per board FLUSH AT BOTTOM Screws per board Cutaway View
STEP 29 Screws Screws Screws per board Screws Screws
STEP 30 ALIGN SCREWS WITH PRE DRILLS Screws Per side Side View Top Screws per board
STEP 31 Screws Side View Bottom
Bolts STEP 32
STEP 33 NOTE HOLES NOTE HOLES TABLE SUPPORT Top View of Table Inside View of Table
STEP 34 Check to make sure structure is square BOTH SIDES TABLE PRE-DRILL BOARDS WITH 1/8 DRILL BIT TO MINIMIZE SPLITTING BOTH SIDES Note: Pre-Drill boards with 1/8 drill bit as shown to prevent splitting.
STEP 35 Make Certain This Side Has Holes Closest To The Edge. TO BOTTOM OF SUPPORT per side SUPPORT TO BOTTOM OF SUPPORT
STEP 36 per side
STEP 37 CENTERED per joint FLAP UP FLAP DOWN FLAP ON THE UNDERSIDE. FLAP ON TOP.
STEP 38 ATTACH SLIDE INTO Screws Slide Stake
Pan Screw STEP 39
STEP 40 1 2 3 4 NOTE: Crimp swing hanger tightly closed Ring-Trap Combo Assembly Attach Quick Link to chain oriented as shown.
STEP 41 BOTTOM OF SEAT BOTTOM OF SEAT Swing Seat Assembly
STEP 42 Carriage Bolt Spacer Loc Nut Steering Wheel Assembly 1. Choose a desired location for the Steering Wheel and drill a 5/16 diameter hole through the lumber. NOTE: If lumber is greater than 2 in depth, you will need to counterbore the hole appropriately. 2. Mount Steering Wheel to climbing unit as indicated. 3. Snap Steering Wheel cap into place.
STEP 43 Telscope Assembly Mounting Screw Mounting Bracket Telescope Assembly STEP 44 Per Flag Flag Assembly
STEP 45 Fold up Anchor-It Strap Screw Anchor-It Note: Keep as little play as possible using any of the holes in the strap that work best. TIP: Drill Bit, or a long screw driver then insert and install the Anchor-Its as shown. This will allow you to get traction with the Anchor-It faster and allow the device to seat more securely.
Warranty and Registration LA 9081 LDR 10-17-2016 Swing-N-Slide Swing-N-Slide MANUFACTURERS LIMITED WARRANTY demonstrates our commitment to providing quality residential playground products. MANUFACTURER S LIFETIME LIMITED WARRANTY Swing-N-Slide warrants its thermoformed slides and climbing mountains to be free from defects in workmanship and materials, under normal use and conditions, for the lifetime of the product. MANUFACTURER S 5 YEAR LIMITED WARRANTY Swing-N-Slide warrants its Custom Ready-to-Build Play Set kits to be free from defects in workmanship and materials, under normal use and conditions, for a period of 5 years. MANUFACTURER S 5 YEAR LIMITED WARRANTY Swing-N-Slide warrants its No-Cut and Wood Complete Ready-to-Assemble Play Set kits against wood rot and termite damage, and to be free from defects in workmanship and materials, under normal use and conditions, for a period of 5 years for structural wood components. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. MANUFACTURER S ACCESSORY, PLAYHOUSE WARRANTY Swing-N-Slide warrants its playset accessories and accessories sold separately as follows: Rope, Canopy/Tarps, Playhouses 1 year. Plastic Components, Chains, Hardware and Fasteners 5 years. These items to be free from defects in workmanship and materials, under normal use Swing-N-Slide will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. Swing-N-Slide at 1212 Barberry Drive, Janesville, Wisconsin, 53545. Any part(s) returned to Swing-N-Slide must have prior approved Return Authorization Number and proof of purchase, including the date of purchase. This warranty is valid only if the product is used for the purpose for which it was designed and installed at a residential, single family dwelling. This warranty is void if the product is put to commercial or institutional use. This warranty does not cover (a) persons; (b) the cost of labor; or the cost of shipping the product, any part, or any replacement product or part. Swing-N-Slide DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. Swing-N- Slide WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the product subsequent to the original purchaser. Some states do not allow limitations on implied warranties or exclusion of also have other rights, which vary from state to state. This warranty also does not apply to: Swing-N-Slide installation plans Swing-N-Slide installation plans Swing-N-Slide
PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration Quick & simple from home or mobile Record your purchase in our system Initiate product warranty Improved customer support Register your product online at www.onlinewarranty.net
Call our Customer Support Representatives Printed in USA