Dt Sheet 707060 Seite 1/10 JUMO Wtrns B Progrmmble Hed Trnsmitter with Rdio Trnsmission Brief description The Wtrns B hed trnsmitter with wireless dt trnsmission is used in connection with Wtrns receiver unit for sttionry or mobile temperture mesuring with RTD temperture probes or thermocouples. Alterntively, resistors with n ohmic-vlue of up to 10 kω, voltges up to 50 mv, nd currents up to 0 ma tht use n externl shunt re mesurble. Customer-specific lineriztions re possible. The mesured vlues re trnsmitted wirelessly to the receiver of the Wtrns mesuring system. These vlues re shown on the receiver's LCD disply nd re digitlly vilble on the RS485- interfce or s nlog output(s). Optionlly, different lrm types cn be indicted with the two rely outputs. This hed trnsmitter is designed for industril pplictions it is mde up of the trnsmitter with n integrted trnsmission unit nd n ntenn-bttery cse. The trnsmitter is designed to be instlled into type B terminl heds nd works in n mbient temperture rnge from -0 to 85 C. It is possible to instll the trnsmitter into customer-specific terminl heds. The ntennbttery cse is connected to the terminl hed through screw connection (M0 1.5). The trnsmission frequency of the Wtrns mesuring system is 868.4 MHz. This frequency is unffected for the most prt by externl interferences nd it llows for trnsmissions even in rough industril environment. When using the ntenn wll-holder with the m ntenn line for the receiver then the mximum open-ir rnge is 00 m. A.6 V,. Ah (size AA) lithium bttery is used s power supply for the trnsmitter. For the esy configurtion nd prmeteriztion of the hed trnsmitter nd the Wtrns receiver on PC n optionl setup progrm is vilble. Additionlly, mesured vlues cn be recorded on the PC with the online-chrt function. Type 707060/... Block digrm Anlog input RTD temperture probe Thermocouple Resistnce / Potentiometer Resistnce trnsmitter + Voltge - Hed trnsmitter Trnsmission unit Trnsmission frequency 868.4 MHz Specil fetures Trnsmission frequency: 868.4 MHz Mesuring input for RTD temperture probe, thermocouple, potentiometer nd voltge Configurble probe ID Bttery sttus monitoring Esy bttery chnge Configurble vi setup progrm Customer-specific lineriztion (vlue pirs in tbles or fourth order number), cn be configured on the receiver Online chrt of the mesured vlues vi setup progrm nd receiver Power supply Interfce Lithium bttery.6 V,. Ah Setup
Dt Sheet 707060 Seite /10 JUMO Wtrns The JUMO Wtrns device series lso includes the receivers 9091/... nd the probes 9090/... in ddition to the hed trnsmitter 707060/... JUMO Wtrns - receiver/probe JUMO Wtrns receiver Type T01.EC1 Type T01.EC JUMO Wtrns probe Type T01.G1 Type T0.G1 JUMO Wtrns probe Type T01.G1 Type T0.G1 JUMO Wtrns probe Type T01.G Type T0.G Receiver (voltge supply AC 110 to 40 V or AC/DC 0 to 0 V) 4x nlog outputs x nlog outputs nd x rely outputs Insertion RTD temperture probe Ambient temperture, hndle: -0 to +85 C Ambient temperture, hndle: -5 to +15 C Minerl insulted RTD temperture probe with flexible sheth Ambient temperture, hndle: -0 to +85 C Ambient temperture, hndle: -5 to +15 C With M1 connector for RTD temperture probe Ambient temperture, hndle: -0 to +85 C Ambient temperture, hndle: -5 to +15 C Dt sheet 9091 9090 9090 9090 JUMO Wtrns B Progrmmble hed trnsmitter with rdio trnsmission 707060
Dt Sheet 707060 Seite /10 Technicl dt Anlog input RTD temperture probe Designtion Stndrd Mesuring rnge Mesuring ccurcy Pt100 DIN EN 60751-100 to +00 C ± 0.1 K (TK vlue =.85 10-1/K) -00 to +600 C ± 0. K Pt500 DIN EN 60751-100 to +00 C ± 0.1 K (TK vlue =.85 10-1/K) -00 to +600 C ± 0. K Pt1000 DIN EN 60751-100 to +00 C ± 0.1 K (TK vlue =.85 10-1/K) -00 to +600 C ± 0. K Ni 100 DIN 4760-60 to +50 C ± 0. K (TK vlue = 6.18 10-1/K) Ni 500 DIN 4760-60 to +150 C ± 0. K (TK vlue = 6.18 10-1/K) Ni 1000 DIN 4760-60 to +150 C ± 0. K (TK vlue = 6.18 10-1/K) Pt100 JIS 1604-100 to +00 C ± 0.1 K (TK vlue =.917 10-1/K) -00 to +600 C ± 0. K Pt50 ST RGW 1057 1985-00 to +600 C ± 0. K (TK vlue =.91 10-1/K) Pt100 GOST 6651-94 A.1-100 to +00 C ± 0.1 K (TK vlue =.91 10-1/K) -00 to +600 C ± 0. K Cu50 GOST 6651-94 A.4-50 to +00 C ± 0. K (TK vlue = 4.6 10-1/K) Cu100 GOST 6651-94 A.4-50 to +00 C ± 0. K (TK vlue = 4.6 10-1/K) Connection type -wire or -wire circuit Sensor current < 0.5 ma Led compenstion Not required for -wire circuit (mx. dmissible 11 Ω per line). Mx. configurble led wire resistnce for -wire circuit: Ω. Thermocouples Designtion Stndrd Mesuring rnge Mesuring ccurcy Fe-CuNi L DIN 4710-00 to +900 C ± 0.1 % Fe-CuNi J DIN EN 60584-10 to +100 C ± 0.1 % s of -100 C Cu-CuNi U DIN 4710-00 to +600 C ± 0.1 % s of -100 C Cu-CuNi T DIN EN 60584-70 to +400 C ± 0.1 % s of -150 C NiCr-Ni K DIN EN 60584-70 to +17 C ± 0.1 % s of -80 C NiCr-CuNi E DIN EN 60584-70 to +1000 C ± 0.1 % s of -80 C NiCrSi-NiSi N DIN EN 60584-70 to +100 C ± 0.1 % s of -80 C Pt10Rh-Pt S DIN EN 60584-50 to +1768 C ± 0.15 % s of 0 C Pt1Rh-Pt R DIN EN 60584-50 to +1768 C ± 0.15 % s of 50 C Pt0Rh-Pt6Rh B DIN EN 60584 0 to 180 C ± 0.15 % s of 400 C W5Re-W6Re C 0 to 0 C ± 0.15 % WRe-W5Re D 0 to 495 C ± 0.5 % WRe-W6Re 0 to 400 C ± 0.15 % Chromel-Copel -00 to +800 C ± 0.1 % s of -80 C Chromel-Alumel -00 to +17 C ± 0.1 % s of -80 C PLII (Pltinel II) 0 to 195 C ± 0.15 %
Dt Sheet 707060 Seite 4/10 Designtion Stndrd Mesuring rnge Mesuring ccurcy MoRe5-MoRe41 0 to 000 C ± 0. % Cold junction Pt1000 internl Cold junction ccurcy ± 1 K All ccurcies given in % refer to the mximum mesuring rnge Resistnce / potentiometer Designtion Mesuring rnge Mesuring ccurcy Resistnce / potentiometer Lineriztion: 0 to 100 % Resistnce / potentiometer Lineriztion: Resistnce in Ω Connection type Led compenstion > 50 Ω to 400 Ω > 400 Ω to 4000 Ω > 4000 Ω to 10000 Ω ± 400 mω ± 4 Ω ± 10 Ω >50Ω to 10000 Ω ± 0.1 % -wire or -wire circuit Not required for -wire circuit (mx. dmissible 11 Ω per line). Mx. configurble led wire resistnce for -wire circuit: Ω. All ccurcies given in % refer to the mximum mesuring rnge Resistnce trnsmitter Designtion Mesuring rnge Mesuring ccurcy Resistnce trnsmitter Connection type Requirement > 50 Ω to 400 Ω > 400 Ω to 4000 Ω > 4000 Ω to 10000 Ω ± 400 mω ± 4 Ω ± 10 Ω -wire connection R e +R +R s 10000 Ω nd R e +R 1/ R s All ccurcies given in % refer to the mximum mesuring rnge Voltge Designtion Mesuring rnge Mesuring ccurcy Voltge 0to50mV ± 0.1 % All ccurcies given in % refer to the mximum mesuring rnge Mesuring circuit monitoring Mesuring probe Detection of overrnge / underrnge Detection of probe / cble short circuit Detection of probe / cble brek Thermocouple Yes / Yes No Yes RTD temperture probe Yes / Yes Yes Yes Resistnce / potentiometer Yes / Yes Yes Yes Resistnce trnsmitter No / No No No Voltge Yes / Yes No Yes
Dt Sheet 707060 Seite 5/10 Output (rdio trnsmission) Probe ID Mx. 5-digit ID, fctory-set, cn be configured to customer-request Trnsmission intervl Adjustble from 1 to 600 s (fctory setting: 15 s) Trnsmission frequency 868.4 MHz (Europe) Trnsmission power +10 dbm Open ir rnge Mx. 00 m when using the ntenn wll-holder of the receiver nd the m ntenn line. When instlling the ntenn directly on the receiver, reduced rnge of pprox. 40 % must be tken into ccount. Output signl Thermocouple Voltge (mv) RTD temperture probe Resistnce (Ω) Resistnce / potentiometer Percent (%) or resistnce (Ω) Resistnce trnsmitter Percent (%) Voltge Voltge (mv) Configurtion With setup progrm Configurble prmeters Probe ID (mx. 5-digit ID) nd trnsmission intervl Electricl dt Voltge supply Lithium bttery Operting life Bttery chnge Rted voltge:.6 V, rted cpcity:. Ah; size AA Approx. 1 yer with the fctory-set vlues (trnsmission intervl = 15 s) nd t room temperture (brief trnsmission intervl nd high or low mbient temperture reduce the bttery operting life) Only use the lithium bttery vilble s n ccessory Environmentl influences Trnsmitter in the B hed with ntenn-bttery cse Ambient temperture rnge -0 to +85 C Storge temperture rnge / storge humidity -40 to +85 C / reltive humidity 95 % Temperture influence Thermocouple ± 0.005 % / K devition from C plus ccurcy of the cold junction RTD temperture probe ± 0.005 % / K devition from C Resistnce / potentiometer ± 0.01 % / K devition from C Resistnce trnsmitter ± 0.01 % / K devition from C Voltge ± 0.005 % / K devition from C Climte clss 10 cycles t 10 C / 80 C, ccording to IEC 68--0, reltive humidity 95 %, during opertion Vibrtion resistnce According to GL chrcteristic line Admissible mechnicl shock resistnce 10 g / 6 ms, ccording to DIN IEC 68-.9 Electromgnetic comptibility (EMC) According to DIN EN 616-1 Interference emission Clss B Interference immunity Industril requirements Rdio frequency spectrum ETSI EN 00 0-1 (V..1) nd ETSI EN 00 0- (V..1) All ccurcy vlues in % refer to the mximum mesuring rnge.
Dt Sheet 707060 Seite 6/10 Csing Trnsmitter Type Mteril Flmmbility clss Dimensions Dimeter Height with/without connectors Protection type Connections Sensor Antenn Voltge supply Setup Weight Plstic cse to be instlled in connection hed, form B Polycrbonte UL 94 V 44 mm 1 mm / 7 mm IP00: For open instlltion IP65: When instlled in suitble hed, form B -pole connection terminl RM 5 mm, conductor cross-section 1.5 mm² SMB connector -pin heder RM.54 mm 4-pin connector Approx. 5 g Antenn-bttery cse Type Plstic cse with M0x1.5 thred for connection hed, form B Mteril Polyetherimide Flmmbility clss UL 94 HB or UL 94 V-0 Dimensions Dimeter 0 mm Height 115 mm Protection type IP65, ccording to DIN EN 6059 Connection Antenn SMB cble socket, 50 Ω Bttery connection -pole connector RM.54 mm Mounting orienttion Preferbly verticl (optimum lignment is to the receiver ntenn) Weight (including bttery) Approx. 80 g
Dt Sheet 707060 Seite 7/10 Connection elements nd connectors (1) (6) (6) () (5) () (4) (9) (10) (7) (8) (11 (1)SMB ntenn connector (ntenn connection) ()Voltge supply connector (bttery connection) ()Cble guide for ntenn cble nd voltge supply (4)Probe connection (5)Setup connector (6)Mounting holes for instlltion in the terminl hed, form B (7)Voltge supply socket (bttery connection) (8)SMB ntenn socket (ntenn connection) (9)Sel (10)Lock nut (11)Bttery lid screw Connection digrm The connection digrm included in the dt sheet provides initil informtion bout the connection options. Only use the instlltion instructions or the operting mnul for the electricl connection. The know-how nd the correct technicl implementtion of the sfety wrnings/instructions contined in these documents re the prerequisite for the instlltion, electricl connection, nd initil strt s well s for the sfety during opertion. Voltge supply Connection Connector Terminls Symbol nd terminl designtion Lithium bttery, DC.6 V + -
Dt Sheet 707060 Seite 8/10 Anlog input Connection Connector Terminls Symbol nd terminl designtion RTD temperture probe 4 1 nd 1 -wire circuit RTD temperture probe -wire circuit 4 1 to 1 Thermocouple 4 nd + Resistnce / potentiometer -wire circuit 4 1 nd - 1 Resistnce / potentiometer -wire circuit 4 1 to 1 Resistnce trnsmitter A=Strt S = Slider E=End 4 1 to Voltge (0 to 50 mv) 4 nd + E A S 1 Current (0 to 0 ma) 4 nd Mesuring rnge: Voltge (0 to 50 mv) with shunt.5 Ω (see ccessories) - + Shunt - Output Connection Connector Terminls Symbol nd terminl designtion Antenn connector 1
Dt Sheet 707060 Seite 9/10 Interfce Connection Connector Terminls Symbol nd terminl designtion Setup 5 Dimensions Trnsmitter 7 Ø44 Antenn-bttery cse Ø0 115 pprox. 105 pprox. 15 17 49.5
Dt Sheet 707060 Seite 10/10 Order detils (1) Bsic type JUMO Wtrns B 707060 progrmmble hed trnsmitter with rdio trnsmission () Input 8 Stndrd, with fctory settings 9 Customized progrmming ccording to specifiction () Output (probe) 10 Trnsmission frequency 868.4 MHz (Europe) (4) Extr codes 000 None Plese specify the probe ID, trnsmission intervl, mesuring rnge, nd, if required, the probe type in plin text. (1) () () (4) Order code / - / Order exmple 707060 / 8-10 / 000 Delivery pckge 1 trnsmitter in the ordered version (without terminl hed form B) inc. mounting prts ( screws nd compression springs) 1 ntenn-bttery cse with reverse bttery protection connection cbles 1 lithium bttery.6 V,. Ah (size AA) lredy inserted in the ntenn-bttery cse redy for use 1 operting mnul B707060.0 Accessories Article Prt no.: Lithium bttery.6 V,. Ah (size AA) 70/00547559 PC interfce with USB/TTL converter, dpter (socket connector), nd dpter (pins) 70/004565 PC interfce with TTL/RS converter nd dpter (socket connector) 70/005060 Setup progrm on CD-ROM, multilingul 70/00488887 Setup progrm including OnlineChrt on CD-ROM, multilingul 70/00549067 Activtion for OnlineChrt 70/00549188 Precision-resistor type.5 R / 0.1 % (shunt) 70/00555645