Development of a Low-Cost Programmable Microphone Preamp Gain Control IC for Pro Audio Applications Gary Hebert, Chief Technology Officer THAT Corporation 1
Tonight s Presentation Introduction Professional Microphone Preamplifiers Digital Mic Preamp Gain Controllers Earlier Products Cost Reduction Measures Cost-Performance Tradeoffs Measured Performance Conclusions 2
Who s THAT? Founded in 1989 2014 was our 25th anniversary! Spin-off from dbx Inc. Founders were dbx engineers Paul Travaline, Gary Hebert, And Les Tyler Once made complete pro-audio products Now focused on Pro Audio ICs and Licensing 3
Professional Microphone Preamps Balanced (Differential) Input Low input noise required On the order of 150Ω thermal noise (-130.8 dbu in 20 Hz 20 khz BW) Wide gain range required Mic sensitivities vary over at least 37 db Sound levels vary with application Max input level should be +16 dbu for the highest-output condenser microphones 4
Digital Control of Professional Microphone Preamps Many preamps are now front ends for A/D converters in digital audio products. Digital control of the gain gives a uniform user interface for these systems. It also allows enhanced automation features such as setup recall and automatic gain reduction in response to clipping. 5
Typical Preamp Front End Differential gain = 1+ (2R F /R G ) C C capacitors block dc inputs and phantom power R G low valued at high gains to minimize noise 6
What s a Programmable Gain Digitally controlled feedback network for a low-noise differential amplifier Controller? 7
Programmable Gain Controller R G gets small at high gains Small R G implies low R ON switches R F /R G is large at high gains 8
THAT s First Controllers 5171-1 db/step 13.6 db 68.6 db <.0008% THD, +24 dbu out, any gain 5173-3 db/step 0 db 60 db <.001% THD,+24 dbu out, any gain Accurate gains - +/-.5 db max, +/-.15 db typical DC servos 9
5171/5173 Topology Both R F and R G are varied using a combination of a tapped resistor string and a set of switched paralleling resistors. 10
Tapped resistor string is used for large steps Tapped string switches don t effect gain or THD, but do add noise 5171/5173 Topology 11
Minimum RG (in red) is 5.6Ω in the 5171. This resistor is very wide and short. W/L 109 for 610 Ω/sq. poly 5171/5173 Topology 12
Paralleling resistors are used for small steps Paralleling switches are in series with highvalue resistors 5171/5173 Topology 13
Maximum parallel R F (in red) is 47 kω in the 5171. This resistor is narrow and long. W/L.013 for 610 Ω/sq. poly 5171/5173 Topology 14
Show Me the Money The 5171 and 5173 have proven to be too expensive for many applications, particularly those at the entry level where some of the possible automation features might be most useful. So, what makes them expensive, and what do we trade off to make a less costly part? 15
Resistors Bigger is Better Ratio accuracy increases with resistor area. Distortion due to self heating is proportional to:. 16
Switches Bigger is Better R ON is inversely proportional to device width Low R ON minimizes noise from the tap-string switches High voltage capability also increases area 17
Cost Reduction the Easy Stuff 3 db per step Dual channel part Saves some package cost Small savings in SPI interface area Eliminate servo Reduces die area Reduces power Requires large external capacitor 18
New Topology Variable R G Fixed R F Switch R ON added to R G R ON adds THD R ON variation adds gain error 19
Dynamic gate drive minimizes THD due to R ON Reduced max gain (51 db) saves die area New Topology 20
How Much Gain? 125 Dynamic Range vs. Gain 150 150ΩSource, Ideal Preamp Dynamic Range (db) 115 105 95 85-20 -10 0 10 20 30 40 50 Gain (db) 114 DB A/D Dynamic Range (db) 120 db A/D Dynamic Range (db) 21
Bent Binary R G Scheme Binary resistances for R G leads to gain error at low gains Bending a few of the LSBs gives a good fit (+/-.2 db nominal error) Gain Error (db) 1.00 0.80 0.60 0.40 0.20 0.00-0.20-0.40-0.60-0.80-1.00 Gain Error vs. Nominal Gain 0 3 6 9 12 1518 18 2124 2427 27 3033 33 3639 39 4245 45 4851 Nominal Gain (db) Binary R's Bent R's 22
Bent Binary R G Scheme 0 51 db gain 1.00 0.80 range with 10 0.60 switches 0.40 0.20 Actual gain 0.00 accuracy will -0.20-0.40 vary since R ON -0.60 doesn t track -0.80-1.00 poly resistors Gain Error (db) Gain Error vs. Nominal Gain 0 3 6 9 12 1518 18 2124 2427 27 3033 33 3639 39 4245 45 4851 Nominal Gain (db) Binary R's Bent R's 23
Resistor Area Reduction Resistors scaled down to meet the target die area These become the dominant distortion mechanism THD due to resistor self heating is almost pure 3 rd harmonic 24
Performance EIN with THAT 1580 = -128.3 dbu with 150Ω R S, 20 Hz 20 khz BW, 51 db gain Gain Accuracy +/-.5 db 0-39 db +/-1 db 42 51 db 25
Performance 1.00000 THD+N vs Gain at 24dBu Out, 1 khz 0.10000 0.01000 0.00100 0.00010 0 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 26
Performance 27
Performance 1 Typical vs. Theoretical Gain Error 0.8 0.6 0.4 0.2 0-0.2-0.4-0.6-0.8-1 0 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 Typical Gain Error Theoretical Gain Error 28
Additional Features Zero-crossing detectors (ZCDs) for each channel Internal time-out clock counter for ZCD 1 general purpose logic output (GPO) per channel GPOs can be sync d to the ZCD Independent connections for R F resistors for discrete preamp designs that require this 29
Conclusions We achieved a 55% cost reduction per channel compared to our 5173 THD performance was compromised in a manner that seems acceptable to most Noise performance is actually slightly better than the previous designs at most gains 30
Acknowledgements Thanks to Fred Floru of THAT Corporation for his help in reviewing this presentation. Thanks to Rene Jaeger for inviting me to speak tonight. 31
Questions? 32 Interfacing Digitally-Controlled Microphone Preamplifiers to A/D Converters 133 RD AES Convention, Oct 2012 Copyright 2012, THAT Corporation