WLS8- LED Strip Light - PWM Dimmable Datasheet Banner s LED Strip Lights have sturdy aluminum housings, shatterproof windows, and impressive environmental ratings, making them an ideal general-purpose LED light for machine, enclosure, or other industrial lighting applications. Intensity can be controlled from 0 to 00% using Pulse Width Modulation (PWM) on an input control wire 0% brighter and 0% more efficient than previous model Low-profile, space-saving design Rugged, water-resistant IP69K option Available in eight lengths from 5 mm to 0 mm Lensed models or choice of clear or diffuse window Daisy chain power to multiple lights to control intensity simultaneously Optional snap clips for easy installation and repositioning Automatic temperature protection built into the unit. Above 50 C, the light dims to manage heat and protect product lifetime For PWM dimming, use with the LC65 Dimmer Module. For more information, refer to the LC65 LED Dimmer Module datasheet, p/n 77086. Stand-Alone Light cable Stand-Alone Light or End Light in a Cascade QD First Light in a Cascade cable First or Middle of a Cascade QD WLS8- Work Light Strips are available as either stand-alone models, or as cascade models that can be "daisy-chained" together for a continuous length of lighting, with a minimum of wiring. Stand-alone models have cable or male QD fitting at one end for power connection, no connections at opposite end. A stand-alone model may be used as the last in the cascade series. Cascade models have cable or male QD fitting at one end for power connection, female QD fitting at opposite end for connection to other lights in the cascade. Cascade models with cable end can only be used as the first light in the cascade series. A double-ended accessory cordset must be used between each pair of lights in a cascade. Models Family Cascadable LED Color Lighted Length (mm) Window Construction Connector WLS8- C W 5 D X Q C = Cascadable X = Non-cascadable W = Cool white WW = Warm white R = Red G = Green B = Blue Y = Yellow 5 85 0 570 70 850 990 0 X = Not sealed S = Sealed Blank = Clear plastic D = Diffused plastic L5 = 5 deg lensed window Blank = None PB = High/Lo/Off Switch PWM = Pulse Width Modulation Dimming * Models require a mating cordset Sealed models not available with On/Off Switch Blank = m integral cable Q = Integral -pin Euro-style QD (mating cordset required*) Original Document 799 Rev. F 8 May 07 799
WLS8- LED Strip Light - PWM Dimmable Table : IP50 Models Stand-Alone Cascade Lighted Length Power Connector WLS8-XW5XPWM WLS8-CW5XPWM 5 mm WLS8-XW85XPWM WLS8-CW85XPWM 85 mm WLS8-XW0XPWM WLS8-CW0XPWM 0 mm WLS8-XW570XPWM WLS8-CW570XPWM 570 mm WLS8-XW70XPWM WLS8-CW70XPWM 70 mm WLS8-XW850XPWM WLS8-CW850XPWM 850 mm WLS8-XW990XPWM WLS8-CW990XPWM 990 mm WLS8-XW0XPWM WLS8-CW0XPWM 0 mm m cable Table : IP67/IP69K Models Stand-Alone Cascade Lighted Length Power Connector WLS8-XW5SPWM WLS8-CW5SPWM 5 mm WLS8-XW85SPWM WLS8-CW85SPWM 85 mm WLS8-XW0SPWM WLS8-CW0SPWM 0 mm WLS8-XW570SPWM WLS8-CW570SPWM 570 mm WLS8-XW70SPWM WLS8-CW70SPWM 70 mm WLS8-XW850SPWM WLS8-CW850SPWM 850 mm WLS8-XW990SPWM WLS8-CW990SPWM 990 mm WLS8-XW0SPWM WLS8-CW0SPWM 0 mm m cable Wiring Diagram Male Female Pin Wire Color Connection brown to 0 V dc blue dc common black Pulse width modulation (PWM) input. For maximum intensity, leave the black wire floating or connected to common. white Not used Integral m (6.5 ft) unterminated cable models are listed. To order the -pin M/Euro-style integral quick disconnect model, add the suffix "Q" to the model number. For example, WLS8-XW85XPWMQ. www.bannerengineering.com - Tel: +-76-5-6 P/N 799 Rev. F
WLS8- LED Strip Light - PWM Dimmable Specifications Supply Voltage and Current V dc to 0 V dc Use only with suitable Class power supply (UL) or a SELV power supply (CE). Supply Protection Circuitry Protected against reverse polarity and transient voltages Light Characteristics Color: Cool White Color Temperature (CCT): 6000 700K Lumen output: 650 (± 5%) per foot, typical at 5 C (77 F) Luminous efficacy: 90 lumens/watt typical at V dc at 5 C (77 F) CRI: 85, typical LED Lifetime Lumen Maintenance - L 70 When operating within specifications, output will decrease less than 0% after 50,000 hours. Construction Clear anodized aluminum housing; painted zinc end caps; polycarbonate window on clear and diffuse plastic models; acrylic window on L5 models; zinc plated steel brackets Mounting () swivel brackets SMBWLS8RA included and () screws Connections Integral -pin M male quick disconnect (QD) (-pin connecting cordset required); or m (6.5 ft) integral cable Pulse Width Modulation (PWM) Frequency: Up to 000 Hz Voltage: 8 V dc to 0 V dc Current: ma max. per foot Environmental Rating IEC IP50 (non-sealed models) or IEC IP65, IEC IP67, IEC IP69K per DIN 0050 (sealed models) Vibration and Mechanical Shock Vibration 0-55 Hz.0 mm p-p amplitude per IEC 60068--6 Shock 5G ms duration, half sine wave per IEC 60068--7 Operating Temperature 0 C to +70 C ( 0 F to +58 F) Light output begins to decrease above 50 C ( F) and will be approximately 65% of max intensity at 60 C (0 F) and 0% of max intensity at 70 C (58 F) Storage Temperature 0 C to +70 C ( 0 F to +58 F) Certifications D Sealed models only Note: Do not spray cable with high-pressure sprayer, or cable damage will result. Application Note When connecting cascadable lights in series it is important not to exceed maximum current limitations: Maximum length of light at V dc:. m (.6 ft) Maximum length of light at V dc:.0 m (9.8 ft) Maximum length of light at 0 V dc:. m (0. ft) Table : Typical Current Light Length Typical Current Max. Current Lumens (Typical @5 C) V dc V dc 0 V dc A Cool White 5 mm 0. A 0.5 A 0. A 0. 5 85 mm 0.66 A 0.0 A 0. A 0.8 650 0 mm.0 A 0.6 A 0.6 A. 975 570 mm.6 A 0.6 A 0.8 A.6 00 70 mm.75 A 0.77 A 0.60 A.0 65 850 mm. A 0.9 A 0.7 A. 950 990 mm.59 A.08 A 0.85 A.8 75 0 mm.0 A. A 0.97 A. 600 Lumen values lowered by 5% on diffused window models. P/N 799 Rev. F www.bannerengineering.com - Tel: +-76-5-6
WLS8- LED Strip Light - PWM Dimmable Dimensions L5 Models [.55] 8 [.0] 8 [.]. [.7] [.8].5 [.5] 8 [.0] 9.5 [.7] 9 [.75] 0 [.8].5 [.5] Motion Detector Models.0 [.8] 6.9 [.5] ø.7 [.58] ON/OFF Switch Models 0.8 [.8] X M X.50 ISO 7.5 [.0] ø 5 [.0] 0.5 [.].5 [.] 0 [.8] 0.8 [.8] Dimensions are shown with the included SMBWLS8RA bracket. IP50 Models IP67/IP69K Models L L L L WLS8-..5XPWM WLS8-..5SPWM mm (8.7 in) 05 mm (8. in) 5 mm (5.7 in) 75 mm (6.9 in) WLS8-..85XPWM WLS8-..85SPWM 6 mm (. in) 6 mm (.6 in) 86 mm (.6 in) 6 mm (. in) WLS8-..0XPWM WLS8-..0SPWM 50 mm (9.8 in) 87 mm (9. in) 7 mm (6.8 in) 57 mm (8.0 in) WLS8-..570XPWM WLS8-..570SPWM 6 mm (5. in) 68 mm (.7 in) 568 mm (.6 in) 598 mm (.5 in) WLS8-..70XPWM WLS8-..70SPWM 785 mm (0.9 in) 769 mm (0. in) 709 mm (7.9 in) 79 mm (9. in) WLS8-..850XPWM WLS8-..850SPWM 96 mm (6.5 in) 90 mm (5.8 in) 850 mm (.6 in) 880 mm (.6 in) WLS8-..990XPWM WLS8-..990SPWM 067 mm ( in) 05 mm (. in) 99 mm (9.0 in) 0 mm (0. in) WLS8-..0XPWM WLS8-..0SPWM 08 mm (7.6 in) 9 mm (6.9 in) mm (.57 in) 6 mm (5.7 in) Accessories Cordsets Use single-ended cordsets between the power source and the QD connection of a stand-alone light or the first light in a cascade. Use double-ended cordsets between lights in a cascade. -Pin Threaded M/Euro-Style Cordsets Model Length Style Dimensions Pinout (Female) MQDC-06 MQDC-5 MQDC-0 MQDC-50 MQDC-06RA MQDC-5RA MQDC-0RA MQDC-50RA.8 m (6 ft).57 m (5 ft) 9. m (0 ft) 5. m (50 ft).8 m (6 ft).57 m (5 ft) 9. m (0 ft) 5. m (50 ft) Straight Right-Angle M x ø.5 [0.57"] Typ. Typ. [.6"] M x ø.5 0 Typ. [.8"] = Brown = White = Blue = Black www.bannerengineering.com - Tel: +-76-5-6 P/N 799 Rev. F
WLS8- LED Strip Light - PWM Dimmable -Pin Threaded M/Euro-Style Cordsets Double Ended Model Length Style Dimensions Pinout MQDEC-0SS 0. m ( ft) Female MQDEC-0SS MQDEC-06SS MQDEC-SS 0.9 m ( ft).8 m (6 ft).66 m ( ft) 0 Typ. [.58"] MQDEC-0SS MQDEC-0SS MQDEC-50SS 6.0 m (0 ft) 9. m (0 ft) 5. m (50 ft) Male Straight/ Female Straight M x ø.5 [0.57"] Typ. [.7"] M x ø.5 [0.57"] Male = Brown = White = Blue = Black -Pin Threaded M/Euro-Style Splitter Cordsets Flat Junction Model Branches (Female) Trunk (Male) Pinout CSB-M0M0 No branch No trunk CSB-M0M No trunk Female CSB-MM CSB-M8M CSB-M5M x 0.0 m ( ft) 0.0 m ( ft).50 m (8 ft).57 m (5 ft) CSB-M5M 7.60 m (5 ft) Male CSB-UNT5M Ø.5 [0.57"] M x 0 Typ. [.58"] 5 [.8"] Ø.5 [0.8"].0 [.69"] 8.0 [0.7"] 7.60 m (5 ft) Unterminated Typ. [.7"] Ø.5 [0.57"] M x = Brown = White = Blue = Black Brackets SMBWLS8RA The bracket kit is available as a replacement for the one that comes with the Work Light Strip. The kit contains two end brackets and four screws. SMBWLS8SM This kit allows the light to be mounted at a right angle to the mounting surface. The kit contains two end brackets and four screws. P/N 799 Rev. F www.bannerengineering.com - Tel: +-76-5-6 5
WLS8- LED Strip Light - PWM Dimmable SMBWLS8SP Stainless steel snap bracket kit Includes two brackets SMH6 This kit allows the light to be mounted to a /6-inch Unistrut channel. The kit includes: #0- spring nuts (qty ) #0- socket head cap screws (qty ) #0 lock washers (qty ) SMBWLSMAG Magnetic mounting bracket for easy attachment to steel surfaces SMBWLSMAGR Protective cover also available to prevent scratches to painted surfaces Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. Banner Engineering Corp. All rights reserved