M/MI Products M/MI hokes R Series urrent-compensated hokes I Rated currents from 16 to 50 I Up to 0 V or 1000 V I 2- and 3-wire configurations I Horizontal and vertical P mounting types I Ruggedized saturation and thermal behavior I Open construction for forced and convection cooling I Straightforward pin-out for easy P design pprovals Technical specifications Maximum continuous operating voltage: 0 V / 1000 V Operating frequency: to 400 Rated currents: 16 to 50 @ convection cooling High potential test voltage 2500 V, sec, guaranteed, 2 sec factory test winding-to-winding @ 25 : Temperature range (operation and storage): -40 to +125 (40/125/21) Flammability corresponding to: U 94V-0 ooling: convection / forced cooling MTF @ 40 / 230 V (Mil-H-217F): > 5,000,000 hours Typical electrical schematic 1 2 3 1' 2' 3' R common-mode chokes are mainly used to filter MI noise on power lines up to 0 V but they are as well applicable in power lines of photovoltaic installations or similar applications up to 1000 V. MI noise of electronic equipment can go to the power lines and disturb the proper function of other devices like TV sets or radios. Thus noise generated by the equipment from switched power electronics or by high slew rates of controllers needs to be filtered. R common-mode chokes are used to suppress MI noise in P integrated filter designs with line bypass capacitors or in combination with single phase filters for extra low leakage filter designs. Features and benefits I ost-effective P designs for up to 80 with forced cooling * I ompact size and light weight I ow magnetic leakage flux I xcellent winding insulation I Standardized foot print I road range of inductance ratings I ustom-specific versions on request * See pplication Note for forced cooling Typical applications I and filtering for midsize power range drives, photovoltaic inverters, fast chargers, charging stations, UPS and switch mode power supplies I Filter with low leakage current noise or improved immunity against grid disturbances I lectronic devices, automation I onverters
M/MI Products > R Series R Series Selection table convection *forced cooling uctance Resistance hoke Ø Pin ength Weight cooling nominal 3m/s nominal @25 R @25 Pin current @ current @ [] [] [mh/path] [mω/path] [size] [mm] [mm] [g] R6122-16-1M0 16 25 1.00 4.8 1 2.0 ± 0.1 4.5 ± 0.5 130 R6122-25-0M6 25 39 0.64 2.7 1 2.4 ± 0.1 4.5 ± 0.5 135 R6122-36-0M5 36 53 0.45 1.5 2 2.2 ± 0.1 4.5 ± 0.5 180 R6122-50-0M3 50 80 0.25 0.9 2 2.5 ± 0.1 5.0 ± 0.5 172 R6522-16-1M0 16 25 1.00 4.6 3 2.0 ± 0.1 4.5 ± 0.5 132 R6522-25-0M6 25 39 0.64 2.6 3 2.4 ± 0.1 4.5 ± 0.5 126 R6522-36-0M5 36 53 0.45 1.5 4 2.2 ± 0.1 4.5 ± 0.5 180 R6522-50-0M3 50 80 0.25 0.9 4 2.5 ± 0.1 5.0 ± 0.5 175 R8522-16-3M0 16 25 3.00 8.4 4 2.0 ± 0.1 4.5 ± 0.5 172 R8522-25-2M0 25 39 2.00 4.2 5 2.6 ± 0.1 5.0 ± 0.5 268 R8522-36-1M5 36 58 1.50 3.0 6 2.2 ± 0.1 4.5 ± 0.5 440 R8522-50-0M8 50 83 0.75 1.7 6 2.5 ± 0.1 5.0 ± 0.5 430 R6132-16-0M8 16 26.5 0.80 4.6 7 2.0 ± 0.1 4.5 ± 0.5 162 R6132-25-0M5 25 41 0.47 2.4 7 2.5 ± 0.1 5.0 ± 0.5 175 R6132-36-0M4 36 0.42 1.4 8 2.2 ± 0.1 4.5 ± 0.5 278 R6132-50-0M2 50 81 0.18 0.9 8 2.5 ± 0.1 5.0 ± 0.5 264 R6532-16-0M8 16 26.5 0.80 4.7 9 2.0 ± 0.1 4.5 ± 0.5 165 R6532-25-0M5 25 41 0.47 2.4 9 2.5 ± 0.1 5.0 ± 0.5 180 R6532-36-0M4 36 0.42 1.5 10 2.2 ± 0.1 4.5 ± 0.5 280 R6532-50-0M2 50 81 0.18 0.8 10 2.5 ± 0.1 5.0 ± 0.5 268 R8532-16-1M3 16 27 1.30 5.7 9 2.0 ± 0.1 4.5 ± 0.5 176 R8532-25-0M9 25 41 0.94 3.0 11 2.6 ± 0.1 5.0 ± 0.5 282 R8532-36-0M8 36 58 0.83 2.3 12 2.2 ± 0.1 4.5 ± 0.5 478 R8532-50-0M3 50 82 0.33 1.2 12 2.5 ± 0.1 5.0 ± 0.5 442 Test conditions: Measuring frequency: 1k; 500μ > 0.16mH < 1.6mH; 50μ > 1.6mH < 1mH uctance tolerance: +5, 3 Resistance tolerance: ±15% @ 25 ; < 20mΩ 1 lectrical characteristics @ 25 : ±2 * typical current for forced cooling with 3m/s. ue to the possible turbulences and degradation of the air stream within an equipment please consider thermal validation. Order ode: R xxxx-xx-xmx uctance value (e.g. 9M6 = 9.6 mh) Nominal input current [] (convection cooling) Terminal type ( 2 for P pin) 2 = 2-wire choke 3 = 3-wire choke 1 = Horizonzal 5 = Vertical 8 = high inductance series 6 = low inductance series Schaffner standard ring-core choke series R xamples: R8532-16-1M3: Vertical 3-wire high inductance choke with P pins, for 16, with 1.3 mh R6122-50-0M3: Horizontal 2-wire low inductance choke with P pins, for 50, with 0.3 mh
M/MI Products > R Series 1-phase / chokes Size 1 (R6122) Size 2 (R6122) imensions (mm) imensions (mm) 2 1 2' 1' 2 2' ééé é è Size 3 (R6522) 1 imensions 2 3 (mm) 4 circuit diagram ä é 1' 2' SHFFNR MV G 2x0.45 mh 1 For self tapping 1 screw ' M4 1 2 2 For self tapping screw M4 2 ' è Size 4 (R6522/R8522) imensions ä (mm) ( 50) 5.08 0.20 1' 2' SHFFNR MV G 2X3.48.5 self tapping screw M4 For 43.4 35.56 0.30 9.76 40.24 é 17.78 1 5.08 0.20 25.4 0.30 1 30.48 0.30 35.56 0.30 2 1' For self tapping screw M4 llgemeine Toleranzen General tolerances Tolérances en général +5-3 ± aten ( single phase ) data charatéristiques Nennstrom rated current 36 bei umgebungstemp. at an ambient temp. Nennspannung rate voltage tension nominal 250 V.50/ etriebsfre operating frequency fréquence de service 450 bleitstrom im etrieb Operational leakage current courant de fuite en fonction Spannung P- /Fre R8522 only single-wire RM 20.32 mm V erechnung mit - alculation with -tol. alculation avec -tol. Inom. maximaler bleitstrom Max leakage current courant maximale de fuite è Spannung P- /Fre 180 g Size 5 (R8522) Size 6 (R8522) Unterbruch des nullleiters with interruption of avec l'interruption du V the neutral conductor conducteur neutre U 1283 erechnung mit - alculation with -tol. alculation avec -tol. I S/ -US 22.2 NO.8 S 22.2 NO.8 U V 1283 N I/N 939 V -Widerstand -resistance -résistance @ 25 2 4 1 imensions 5 (mm) X 1.5 m0hm Zusätzliche ngaben: 2 6 3 7 4 8 imensions dditional 5 remarks: (mm) 6 7 8 ä circuit diagram +15 14.76 45.24 16.84 37.16 Fuer masse ohne Toleranz for dimensions without tolerance pour mesure sans tolérance ISO2768-m/N22768-m pruefspannung test voltage tension d'essais P -> P Schlusskontr. final test 10.16 contrôle `0.20 final 10.16 `0.20 Factory test: 3.0kv / 50 2sec é atenblatt ( single phase ) date sheet fiche technique Wiederholung mit 8 repetition with 8 5.08répétition `0.20 avec 8 Guaranteed: 3.0kv / 50 sec projection scale der angegebenen Werte of the specified values des valeurs spécifiques opyright by 1' 2' 1' 2' SHFFNR MV G Type R6522-36-0M5 Zulaessige etriebstemp. temperature range - bis/to/a + gamme de température 40 125 date name drawn 20.01.2011 fiona.chen SHFFNR MV G F 40 / 125 / 21 klimatische pruefklasse climatic test class classe d'essais climatique 50002499 12.01.2012 Fiona ds approved 12.01.2012 Ice.li Part-NO. 811874 (I/I 068-1) ind revision date name doc.approved 12.01.2012 Ice.li 2x0.75 mh Schaffner M Type R6522-36-0M5 811874 Shanghai hina 2Xn3.4 SH x8.5 811874 2Xn3.4x8.5 For self plot tapping date page 1 von 1 1 1 2 For self 3 tapping 1 ' 4 screw M4 screw M4 1 2 1 2 20.32 `0.30 30.48 `0.30 35.56 `0.30 30.482 `0.30 2 ' 45.9 38.1 `0.30 19.05 50.5 20.32 Max. 58 F llgemeine Toleranzen General tolerances Tolérances en général +5-3 ± aten ( single phase ) data charatéristiques rated Nennstrom current bei umgebungstemp. at an ambient temp. 50/ Nennspannung rate voltage tension nominal 450 etriebsfre operating frequency fréquence de service V.50/ bleitstrom im etrieb Operational leakage current courant de fuite en fonction Zusatzangaben additional information Spannung P- /Fre informations supplementaires V erechnung mit - alculation with -tol. alculation avec -tol. Inom. 268 g maximaler bleitstrom Max leakage current courant maximale de fuite Spannung P- /Fre Unterbruch des nullleiters with interruption of avec l'interruption du V the neutral U 1283 conductor conducteur neutre S/ -US erechnung mit - alculation 22.2 with NO.8 S 22.2 NO.8 U V 1283 N I/N 939 -tol. alculation avec -tol. I V.2 m0hm Zusätzliche ngaben: -Widerstand -resistance -résistance @ 25 2 X 1.7 dditional remarks: m0hm +15 25 Max. 68 250 400 50 Max. 80 Zusatzangaben additional information informations supplementaires U 1283 S/ -US 22.2 NO.8 S 22.2 NO.8 U V 1283 N I/N 939 V Zusätzliche ngaben: dditional remarks: 430 g
M/MI Products > R Series 3-phase chokes Size 7 (R6132) Size 8 (R6132) imensions (mm) 3 2 1 1' 3' é 2' è Size 9 (R6532/R8532) For self tapping screw M4 Size 10 (R6532) 4 imensions 5 (mm) 6 7 8 imensions ä (mm) 1 2 3 4 5 ä 62 circuit diagram 58 é 53.94 3.68 `0.20 44.32 é 1.94 `0.20 1' 2' 3' 1' 2' 3' SHFFNR MV G 3x0.18 mh SHFFNR MV G 2xn3.4x8.5 1 For self tapping 1 ' screw M4 2XSH n3.4x8.5 811893 For self tapping SH 811891 screw M4 1 2 3 2 1 2 3 2 ' 20.32 `0.30 30.48 `0.30 55 48.26 `0.40 24.13 ééé imensions (mm) è 58 25.4 3 2 1 1' 3' 2' For self tapping screw M4 3 3' 55.88 `0.40 25 50/ 400 e 2.4 m0hm sec sec + 125 F 21 4 25 0/ 400 llgemeine Toleranzen General tolerances Tolérances en général aten ( ) data charatéristiques Nennstrom bei umgebungstemp. Spannungsunsymmetrie Zusatzangaben (I 1000-2-4) non symmetrical voltage additional information tension non symétric (I 1000-2-4) informations supplementairesv (I 1000-2-4) `3 Ityp. alculation avec -tol. erechnung Vergussmasse mit - potting compound matière de moulage (I 1000-2-4) Size 11 (R8532) alculation with -tol. maximaler bleitstrom Max leakage current courant maximale de fuite Spannung P- /Fre Gewicht von 2 Phasen Weight open circuit Poids 180 g Unterbruch 2 phases 2 phases circuit V ouvert defecteux erechnung mit - alculation with -tol. 1imensions U 1283(mm) S/ -US 22.2 NO.8 S 2 3 N I/N I V 4 alculation avec -tol. 22.2 NO.8 U V 1283 939 3 0.8 @ 25 X m0hm -Widerstand circuit diagram Zusätzliche ngaben: -resistance -résistance 5.68 additionals: 46.32 dditional remarks: Remarques +15 pruefspannung test voltage tension d'essais Fuer masse ohne Toleranz for dimensions without tolerance pour mesure sans P tolérance -> P ISO2768-m/N22768-m Schlusskontr. Wiederholung atenblatt mit 8 der angegebenen Werte final test repetition ( multi with phase 8 of the specified 2' 3' final ) 3x0.33 répétition avec date mh 8 sheet des valeurs spécifiques 50 2sec fiche technique 50 sec 1' contrôle Factory test: 3.0kv / Guaranteed: 3.0kv / values opyright etriebstemp. by SHFFNR MV temperature range 1-40 bis/to/a + 1 R6532-25-0M5 ' 40 / 125 / 21 projection scale température 125 Zulaessige gamme de Type G date name klimatische pruefklasse climatic test class classe d'essais climatique drawn 20.01.2011 fiona.chen (I/I 068-1) Part-NO. 2Xn3.4x8.5811898 12.01.2012 Ice.li 50002499 12.01.2012 Fiona ds approved doc.approved ind revision date name 12.01.2012 Ice.li For self tapping Type srew M4 SH 811900 811898 Schaffner M R6532-50-0M2 Shanghai hina 1 2 3 4 20.32 `0.30 1 2 date 2 ' 1 plot page von 2 3 58 25.4 uenz Spannungsunsymmetrie non symmetrical voltage tension non symétric V (I 1000-2-4) (I 1000-2-4) (I 1000-2-4) `3 erechnung mit - alculation with -tol. alculation avec -tol. Ityp. maximaler bleitstrom Max leakage current courant maximale de fuite Spannung P- /Fre Unterbruch von Gewicht 2 Phasen 2 phases open Weight circuit 2 phases circuit Poids V 282 g ouvert defecteux erechnung mit - alculation with -tol. alculation avec -tol. I U 1283 S/ -US 22.2 NO.8 S 22.2 NO.8 U V 1283 N I/N 939 V -Widerstand -resistance -résistance @ 25 X m0hm 3 1.2 m0hm Zusätzliche ngaben: dditional remarks: +15 pruefspannung test voltage tension d'essais Max. 58 45.72 `0.40 62 3 3' llgemeine Toleranzen General tolerances Tolérances en général +5 aten ( multi phase ) data charatéristiques Nennstrom bei umgebungstemp. rated current 50 at an ambient temp. etriebsfre operating frequency fréquence de service bleitstrom im etrieb Operational leakage current courant de fuite en fonction rated current at an ambient temp. Nennspannung rate voltage tension nominal etriebsfre operating frequency fréquence de service bleitstrom im etrieb Operational leakage current courant de fuite en fonction Spannung P-P /Fre Max. 70 +5 ± -3 0 V.50/ Nennspannung rate voltage tension nominal 400 Spannung P-P /Fre -3 ± 0 V.50/ 400 50 F Zusatzangaben additional information informations supplementaires Vergussmasse Size 12 (R8532) Vergussmasse potting compound matière de moulage Gewicht Weight Poids imensions (mm) U 1283 S/ -US U V 1283 N I/N 939 V 22.2 NO.8 S 22.2 NO.8 76 Zusätzliche ngaben: dditional remarks: 54.44 1.44 `0.20 Fuer masse ohne Toleranz for dimensions 1' without 2' tolerance 3' pour mesure sans tolérance atenblatt ( multi phase ) date sheet fiche technique projection scale opyright by SHFFNR MV G Type R6532-50-0M2 date name drawn 23.02.2011 fiona.chen 2Xn3.4x8.5 50002499 12.01.2012 Fiona ds approved 12.01.2012 Ice.li Part-NO. 811900 ind revision date name doc.approved 12.01.2012 Ice.li For self tapping Schaffner M screw M4 Shanghai hina SH 811900 1 2 3 plot date page 1 von 1 Zusatzangaben additional information informations supplementaires 63 30.48 `0.30 55.88 `0.40 S/ -US 55.88 `0.40 Zusätzliche ngaben: dditional remarks: 27.94 U 1283 22.2 NO.8 63 S 22.2 NO.8 U V 1283 N I/N 939 Fuer masse ohne Toleranz for dimensions without tolerance pour mesure sans tolérance ISO2768-m/N22768-m Max. 70 Max. 82 V 268 g 442 g F
M/MI Products > R Series Typical choke attenuation/resonance frequency characteristics Per ISPR 17; 50Ω/50Ω asym R6122, R6522 R8522 16 16 50 50 10 4 10 5 10 6 10 7 10 4 10 5 10 6 10 7 R6132, R6532 R8532 16 16 50 50 10 4 10 5 10 6 10 7 10 4 10 5 10 6 10 7 Typical saturation characteristics uctance (typical value in %) vs. nominal current ( ) 16 25 36 50 1 1 1 1 R8532 8 R6132/ R6532 8 R6132/ R6532 8 R8522 R6132/ R6532 8 R8522 R6132/ R6532 % % R6122/ R6522 % R8532 % R8532 R6122/ R6522 R8522 R6122/ R6522 R6122/ R6522 R8522 R8532 0 16 32 48 64 80 0 25 50 75 100 0 36 72 108 144 0 50 100 150 200 Your local partner: To find your local partner within Schaffner s global network, please go to www.schaffner.com
Headquarters, global innovation and development center Schaffner Group Nordstrasse 11 4542 uterbach Switzerland T +41 32 681 66 26 F +41 32 681 66 30 info@schaffner.com www.schaffner.com To find your local partner within Schaffner s global network, please go to www.schaffner.com 2012 Schaffner Group Specifications are subject to change within notice. The latest version of the data sheets can be obtained from the website. ll trademarks recognized. Schaffner is an ISO-registered company. Its products are designed and manufactured under the strict quality and environnmental requirements of the ISO 9001 and ISO 14001 standards. Sales and application centers hina Schaffner M td. Shanghai T20-3, No 565 huangye Road Pudong New rea Shanghai 201201 T +86 21 3813 9500 F +86 21 3813 9501 / 02 cschina@schaffner.com www.schaffner.com Finland Schaffner Oy Sauvonrinne 19 H 08500 ohja T +358 19 35 72 71 F +358 19 32 66 10 finlandsales@schaffner.com France Schaffner M S..S. 112, Quai de ezons 95103 rgenteuil T +33 1 34 34 30 F +33 1 39 47 02 28 francesales@schaffner.com Germany Schaffner eutschland GmbH Schoemperlenstrasse 12 76185 Karlsruhe T +49 721 56910 F +49 721 569110 germanysales@schaffner.com Italy Schaffner M S.r.l. Via Galileo Galilei, 47 20092 inisello alsamo (MI) T +39 02 66 04 30 45/47 F +39 02 61 23 943 italysales@schaffner.com Japan Schaffner M K.K. Mitsui-Seimei Sangenjaya ldg. 7F 1-32-12, Kamiuma, Setagaya-ku Tokyo 154-0011 T +81 3 5712 3650 F +81 3 5712 3651 japansales@schaffner.com www.schaffner.jp Singapore Schaffner M Pte td. lk 3015 Ubi Road 1 05-09 Kampong Ubi ustrial state T +65 6377 3283 F +65 6377 3281 singaporesales@schaffner.com Spain Schaffner M spaña alle aléndula 93 Miniparc III, dificio l Soto de la Moraleja lcobendas 28109 Madrid T +34 618 176 133 spainsales@schaffner.com Sweden Schaffner M Turebergstorg 1, 6 19147 Sollentuna T +46 8 5792 1121 / 22 F +46 8 92 96 90 swedensales@schaffner.com Switzerland Schaffner MV G Nordstrasse 11 4542 uterbach T +41 32 681 66 26 F +41 32 681 66 41 sales@schaffner.ch Taiwan Schaffner MV td. 6th Floor, No 413 Rui Guang Road Neihu istrict Taipei ity 114 T +886 2 87525050 F +886 2 87518086 taiwansales@schaffner.com Thailand Schaffner M o. td. Northern Region ustrial state 67 Moo 4 Tambon an Klang mphur Muang P.O. ox 14 amphun 51000 T +66 53 58 11 04 F +66 53 58 10 19 thailandsales@schaffner.com UK Schaffner td. 5 shville Way Molly Millars ane Wokingham erkshire RG41 2P T +44 118 9770070 F +44 118 9792969 uksales@schaffner.com www.schaffner.uk.com US Schaffner M Inc. 52 Mayfield venue dison, New Jersey 08837 T +1 732 225 9533 F +1 732 225 4789 usasales@schaffner.com www.schaffner.com/us 10/2012 N This document has been carefully checked. However, Schaffner does not assume any liability for errors or inaccuracies.