Designed for co-siting purposes Enables feeder sharing Can be used as a combiner near the BTS or in a reciprocal function near the antenna Suitable for indoor or outdoor applications Wall or mast mounting Available as a single unit, or for XPol antennas as a double unit Built-in lightning protection External DC available as an accessory Technical Data Type No. 78210700 78210701 Pass band Band 1 Band 2 Band 3 Insertion loss Port 1 Port 4 Port 2 Port 4 Port 3 Port 4 78210702 78210703 690 806 824 960 1427 3800 < 0.5 (690 796 ); < 0.7 (796 806 ) < 0.7 (824 834 ); < 0.5 (834 960 ) < 0.15 (1427 3800 ) 78210704 78210705 Isolation > 45 VSWR < 1.25 Impedance Ω 50 Input power Band 1 / Band 2 / Band 3 W < 200 / < 200 / < 200 (1427 2700 ); < 100 (2700 3800 ) Intermodulation products c < -160 (3 rd order; with 2 x 20 W) Temperature range C F 40... +60 40... +140 Connectors 4.3-10 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 Port 4 Port 2 Port 4 Port 3 Port 4 clamps included clamps included Lightning protection ka 3, 10/350 μs pulse Mounting mm in Wall mounting: With 4 screws (max. 8 0.315 diameter) / Mast mounting: With included clamp set Weight kg lb : 5 11.0 / : 9.9 21.8 Packing size mm in : 405 x 295 x 170 15.95 x 11.61 x 6.69 : 405 x 295 x 260 15.95 x 11.61 x 10.24 Dimensions (w x h x d) mm in : 222 x 222 x 86.5 8.7 x 8.7 x 3.4 : 222 x 222 176 8.7 x 8.7 x 6.9 (without connectors, without mounting brackets) 78210700... 78210705 Page 1 of 4
Accessories (included) Type No. Clamp set suitable for mast diameter of 734365 [mm in] 45 125 1.77 4.92 Clamp Set Diagram 1 Port 1 Port 4 690-806 Typical Attenuation Curves Port 2 Port 4 824-960 Port 3 Port 4 1427-3800 Accessories (order separately) Type No. Description 78211000 DC stop 78210484 50-Ohm load DC stop 50-Ohm load Diagram 2 Port 1 Port 4 690-806 Port 2 Port 4 824-960 Port 3 Port 4 1427-3800 Please Note: The mounting plates can be removed by loosening the screws j to m (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of a mast mounted device or even cause it to fall to the ground. These facts must be considered during the site planning process. The Combiners are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the combiners and accessories. The limits for the coupling torque of RF connectors, recommended by the connector manufacturers must be obeyed. Terminate unused inputs with a suitable 50-Ohm load, e.g. 78210484. Any previous datasheet issues have now become invalid. Page 2 of 4 78210700... 78210705
Dimensions 78210700... 78210705 Page 3 of 4
Dimensions Page 4 of 4 78210700... 78210705
General Information about Panel Antennas Environmental conditions: Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items: Low temperature: 55 C High temperature (dry): +60 C For antennas equipped with FlexRET: The electrical downtilt adjusting is designed to operate under the environmental conditions as described in the valid data sheet of the FlexRET. Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Environmental tests: Please note: Kathrein antennas fulfil the stated specifications after completion of the environmental tests as defined in ETS 300 019-2-4. The homogenous design of Kathrein s antenna families uses identical modules and materials. Extensive tests have been performed on typical samples and modules. The vibration test has been adapted relating to frequency and acceleration to the conditions of mast mounted antennas. As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. 936.4694/d Subject to alteration. EU-RED The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4. Wind loads are calculated according to DIN 1055-4. The antennas may be used at locations where the anticipated peak wind velocity or gust wind speed lies within the maximum wind speed listed in the data sheet. We warrant the mechanical safety and electrical functionality under such conditions. The wind speeds are defined in accordance with the DIN, EN or TIA standards. This warranty makes allowance for the partial safety factors specified in those standards. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. Site planning and installation must be carried out by qualified and experienced staff. All relevant national safety regulations must be upheld and respected. Incorrect site planning, faulty installation, as well as interfering surroundings on site, may lead to deviations in the electrical parameters compared to those specified in the respective data sheets. The connectors on this product are only suitable for connecting to the compatible counterpart. Please ensure that the connected cable has been fitted with a connector of the same standard, otherwise damage may occur. The tilt values will be set to any arbitrary value in the given tilt range. These values are independent from the frequency band or antenna type and can vary between antennas and bands. Hereby, Kathrein Werke KG declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http:// Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001. RoHS Our products are compliant to the EU Directive RoHS as well as to other environmentally relevant regulations (e.g. REACH). Any previous data sheet issues have now become invalid. Page 1 of 1 KATHREIN-Werke KG Anton-Kathrein-Straße 1-3 P.O. Box 10 04 44 83004 ROSENHEIM GERMANY Phone +49 8031 184-0 Fax +49 8031 184-820