A few notes about PDF patterns from.... This PDF pattern requires legal size paper (8.5 x 14 ) or A4 size paper (8.27 x 11.69, 210mm x 297mm). It will not print on standard letter. Patterns containing larger pieces will need to be taped together before cutting out the fabric. Be advised that this document needs to be printed to it s original scale. Please ensure that the printing options below are not selected. Do Not: Rotate and Center, Fit to Page, Reduce to Fit or adjust the scale of this document. Refer to the scale marker below to ensure that this copy is printed at the correct scale. This PDF pattern is not licensed for commercial use and may not be shared, duplicated or distributed. 2016, All RIGHTS RESERVED. Personal use only. Not licensed for commercial use. 1 or 25.4mm 1 or 25.4mm
www.fletcherpatterncompany.com Versatility for 13 Revlon Dolls Designed by Tamara Casey REV101 $12.95 US 2011, All RIGHTS RESERVED. Personal use only. Not licensed for commercial use.
Versatility For 13 Revlon Fabric: Pants Cottons, linen, lightweight denim and blends. Top Sweater knit, knits, cotton blends with some stretch Notions: 4ct. 4/0 snap sets, matching thread, optional buckle for a belt Instructions Sewing instructions for both pants are the same. You can choose slim leg or flared. The same waistband is used for both. Pants 1. Sew darts in pants back. (these are very small darts) 2. With right sides together sew center front seam of pants. Clip seam and press. 3. With right sides together sew pants front sections to pants back sections at the side seams. 4. Turn pants legs under ¼ and hem. 5. Serge lower edge of waistband. 6. Sew pants together from crotch to dot indicated on the pattern. 7. With right sides together, pin waistband to pants leaving a slight overhang on each end. 8. Serge both back openings. 9. Turn back left opening under ¼. 10. Fit pants to doll. 11. Fold waistband into pants and hand stitch in place, tucking raw edge under. 12. Fit to doll and sew snap set in place. Sewing instructions for both tops are the same. You can choose ¾ length or full sleeves and the slim or wide collar. Make sure to choose a fabric with some stretch. Sweater knits should have a tight weave for best results. Top 1. Hem sleeve edge 2. Sew sleeve to armhole edges of the top front. 3. Sew sleeve to armhole edge of the back sections. 4. With right sides together sew underarm seams, matching armhole seams. 5. With wrong sides together, fold the collar piece in half. Pin to the neck edge of the top. Sew in place. 6. Press the seam down and top stitch if desired. 7. Hem lower edge of top. 8. Sew center back seam from hem edge to dot. 9. Finish back opening left over right. 10. Sew snaps in place to secure. Belt 1. Cut a strip of scrap leather approximately 5 ½ x 3/8. 2. Pull on end of the strip through the buckle and secure. 3. Fit the belt to the doll with outfit on and trim end. (change the width of the strip depending on the measurement of the buckle opening you choose). www.fletcherpatterncompany.com
Piece Full Length Sleeve Piece Flared Pant Back Piece Flared Pant Front Piece Pants Waistband Piece Top Back Piece Slim Collar 2011, All RIGHTS RESERVED. Personal use only. Not licensed for commercial use.
Fold Line Stitch Line Grain Line Notch Dot Snap Seam allowance of 1/4 is already included in the dimensions of the pattern Piece Slim Leg Pant Front Piece Slim Leg Pant Back Piece 3/4 Length Sleeve esigns by Jude cut on fold Piece Wide Neck Collar Piece Top Front on fold 2011, All RIGHTS RESERVED. Personal use only. Not licensed for commercial use.