General escription he is a powerful ramp/soak controller with a large program storage capacity of 0 segments (99 patterns with 0 segments each to 0 patterns with 99 segments each). his / I controller offers guaranteed soak for precise, critical temperature control requirements. With a ±0.% accuracy, 0. sec. sampling time, five digit display, universal input and multi-level PI or segment PI, this instrument is adaptable to a wide range of process applications. Standard features include three mode operation, four digital inputs, four digital output and Wait functions, temperature alarms, and constant slope start. Some of the optional features include analog outputs and digital communications. Features ±0.% high accuracy Five digit display hree control modes Large program storage Heat/Cool PI with autotuning start selection High Intensity isplay All necessary information is visible on the easy-to-read front display. Program/Segment remaining time display (Unit: hour:min/min:sec) ime signal/ igital output indicators S A RE S O AL OU OU OU wo types of signal modes You can select a pattern mode that works within the pattern or a segment mode that works within the segment. (Please specify one of the two) S S8 Segment ime signal output Pattern Segment signal output Running pattern/ Segment display Gradient state display Large emory OU OU OU Program pattern/ Output bargraph display he can store up to 0 segments (99 patterns with 0 segments each to 0 patterns with 99 segments each). patterns by segments, yet all patterns are linkable to form a large program) ew control algorithm RSS (Ramp Soak Stabilizer) A newly developed control algorithm designed exclusively for ramp/soak controls improves follow-up performance while simultaneously suppressing overshoot at the transition from ramp to soak. Suppress overshoot S S8 Level-PI or Segment PI Select the best PI option for your application. he set values are stored in 8 stage levels or in 8 memory groups. <Level-PI> Full scale C <Segment PI> ax.8 stage levels Level : PI Level : PI Level : PI Level : PI ime _0E Improved follow-up Ramp Soak PI o. PI o. PI PI PI PI o. o. o. o.6 ax.8 memory groups PI o.7 PI o.8 ime
P SEG RU FIX A HOL SEP P SE P E P SEG RU FIX A HOL SEP P SE P E Ramp/Soak Process/emperature Controller Features umerous inputs and outputs Collaborative program operation (Inter-controller communication) Universal input hermocouple R C voltage C current Up to points igital input Pattern o selection Pattern set WAI release irect/reverse action selection RU//HOL/SEP Communication ASI, OBUS communication Inter-controller communication Up to points RS-C/A/8 Output (OU) Control output (Heat control, Cool control, Heat/Cool control, H S Position proportioning control) Output program, Retransmission A S AL OU output, ime signal OI OU OU RS-8 Loader communication Up to points igital output Event, Heater break alarm, Loop break alarm, abnormality, FAIL, Status output, Communication failure, ime Signal (S to S8) Pattern end output Up to slave instruments (FB/RB series and /90) can be connected via exclusive communication port. igital communication gives isolated communication without setting error, ratio setting of individual slave controller, memory area selection and Run/Stop switchover. H S A S AL OI OU OU OU (aster) CO (Inter-controller CO) FB00 (Slave) RS-8 (OBUS) CO CO CO CO FB00 FB00 FB00 (Slave) (Slave) (Slave) aximum of point program pattern outputs (Output program function) Up to analog outputs can be used to control three types of devices (such as a motorized valve). Combining time signal outputs allows programming for complex applications. P SEG S A S O AL Output (%) OU OU OU RU FIX A HOL SEP P SE P E OI Segment Segment Segment emory group ime signal output OU OU Analog output Analog output Analog OU output Catalytic Steam Warm water OU OU OU Segment ime Set values of P, I,, event, segment wait, time signal, program pattern output can be stored in memory groups and can be called up for a segment to be set. 00% 0% 00% 0% 00% 0% otorized valve Ventilation valve PI memory : 8 groups Setting items: Proportional band, Integral time, erivative time, Control response parameter, Cool side proportional band, Cool side integral time, Cool side derivative time, eadband/overlap, eutral zone, anual reset, Output limiter (high/low), Cool side output limiter (high/low), O/OFF differential gap (high/low), LBA time, LBA headband Event memory : 8 groups Setting items: Event to Segment wait memory : 8 groups Setting items: Wait zone, Wait release trigger, imeout for wait ime signals memory : 6 groups Setting items: ime signal output destination, starting segment, time signal starting time, end segment, time signal end t Program pattern output : Up to 99 points Setting items : Output program to emory area needs to be selected on FB series. If you use FB00, FB900 or for a slave device, please select Communication. Communication protocol among slave devices is odbus. odels available as a master device /PF90 : Suffix codes for communication : W, X, or Y odels available as a slave device FB00 : Optional codes : E, F, H, or J FB00/FB900 : Suffix codes for communication : or X RB00/RB00/RB00/RB700/RB900 : Suffix codes for communication :, 6, B or C /90 : Suffix codes for communication : or X Easy data management he comes with a front loader port and programming tool making complicated programming visual and simple to place on a PC. ownloading or Uploading large numbers of set values can be achieved with ease. USB port Start here are four types of start available on the. When ramp/soak control is started: start : ime of segment is not changed whatever the setting. start : ime of segment will be shortened to keep the slope of segment. start : will search pattern for value that is the same as and go to that part of the pattern. Control status will be at Hold until operator presses Run key to start pattern from that point. start : will search pattern for value that is the same as and go to that part of the pattern. Control status will be at Run and the instrument will start pattern from that point. start (Fixed time type) 0 ime start (ime shortening/constant slope type) USB communication converter CO-K- (With loader communication cable) CO-K- (Without loader communication cable) CO-K Loader com Front loader interface USB (Loader cable) (USB cable comes with CO-K) odel code for cable only : (Complete with loader communication W-BV-0-00 cable for ) start / (ime shortening/ pattern search type) 0 ime 0 ime _0E
_0E Universal input a) emperature, Current, Low voltage input group hermocouple : K, J, R, S, B, E,, (JIS/IEC), PLII (BS), WRe/W6Re (AS), U, L (I) Pt0%Rh-Pt0%Rh Influence of external resistance : Approx. 0.μV/Ω break action : Up-scale / own-scale (Selectable) R : Pt00 (JIS/IEC), JPt00 (JIS) Influence of input lead resistance : Approx. 0.0[%/Ω] of reading aximum 0Ω per wire break action : Up-scale Low voltage : 0 to V C, 0 to 00mV C, 0 to 0mV C, - to V C. -00 to +00mV C, -0 to +0mV C break action : Up-scale / own-scale (Selectable) b) High voltage input group High voltage : 0 to V C, to V C, 0 to 0V C - to +V C, -0 to +0V C break action : Uncertain (indicates a value around 0V) c) Current : to 0mA C, 0 to 0mA C break action : Uncertain (indicates a value around 0mA) Sampling ime 0. sec 0.0sec or 0.sec is available. igital Filter 0. to 00.0 sec (OFF when 0 is set.) Bias -span to +span Ratio 0.00 to 9.999 Square Root Extraction Equation : = Ö ( value x ratio + bias) Low level cut OFF : 0.00 to.00% of span Performance easuring Accuracy a) hermocouple ype : K, J,, E,, PLII, U, L Less than -00 C (-8 F) : ±.0 C (±.8 F) -00 to 00 C (-8 to 9 F) : ±0. C (±0.9 F) ore than 00 C (9 F) : ±0.% of Reading ype :, S, R, WRe/W6Re Less than 0 C ( F) : ±.0 C (±.6 F) 0 to 000 C ( to 8 F) : ±.0 C (±.8 F) ore than 000 C (8 F) : ±0.% of Reading ype : B Less than 00 C (7 F) : ±70.0 C (±6 F) 00 to 000 C (7 to 8 F) : ±. C (±.6 F) ore than 000 C (8 F) : ±0.% of Reading ype : PR0-0 (Pt0%Rh-Pt0%Rh) Less than 00 C (7 F) : ±0 C (±6 F) 00 to 000 C (7 to 8 F) : ±0 C (±8 F) ore than 000 C (8 F) : ±0.% of Reading Cold junction temperature compensation error ±.0 C (.8 F) [at to 0 C ( to 0 F)] Within ±. C (±.7 F) [Between -0 and C (6 to F), 0 and C (0 to F)] b) R Less than 00 C (9 F) : ±0. C (±0. F) ore than 00 C (9 F) : ±0.% of Reading c) C voltage and C current ±0.% of span Insulation Resistance ore than 0Ω (00V C) between input terminals and ground ore than 0Ω (00V C) between power terminals and ground ielectric Strength 00V AC for one minute between input terminals and ground 00V AC for one minute between power terminals and ground Control Control ethod a) Brilliant II PI control Available for reverse and direct action. b) Brilliant PI control (Heat/Cool type) c) Position proportioning control Available for reverse and direct action. Position proportional control can be used with/without FBR (feedback resistance) input. a), b), c) is selectable. Autotuning ethod a) For PI control or position proportioning control b) For Heat/Cool PI control (For extruder, air cooling type) c) For Heat/Cool PI control (For extruder, water cooling type) d) For Heat/Cool PI control Autotuning with auto soak detect his is a function to search program soak areas and perform autotuning in the order of segments at the time of reset. his feature is enabled/disabled for ramp segment. ajor Setting Range Set value : Same as input range. Proportional band : 0 (0.0/0.00) to input span ( C, F) (for temperature input) 0.0 to 000.0% of input span (for voltage/current input) (O/OFF control when P = 0) ifferential gap at O/OFF control (High/Low individual setting) emperature input : 0 (0.0/0.00) to input span ( C, F) Voltage/Current input : 0.0 to 00.0% of input span Integral time : 0 (0.0) to 600 (600.0)sec. (selectable) erivative time : Program ime Accuracy : Storage Program Pattern : ax. 99 patterns Storage Segments : ime Setting : Segment Repeat : Pattern Repeat : Linkable Patterns : (P control when I = 0) 0 (0.0) to 600 (600.0)sec. (selectable) (PI control when = 0) Cool-side proportional band : (0./0.0) to input span ( C, F) (for temperature input) 0. to 000.0% of input span (for voltage/current input) Cool-side integral time : 0 (0.0) to 600 (600.0)sec. (selectable) (P control when I = 0) Cool-side derivative time : 0 (0.0) to 600 (600.0)sec. (selectable) (PI control when = 0) eadband/overlap : -span to +span (emperature input) -00.0 to +00.0% of span (Voltage, Current input) Control response : Slow, edium, Fast Output limiter : -.0 to +0.0% (High/Low individual setting) Cool-side output limiter : -.0 to +0.0% (High/Low individual setting) Proportional cycle time : 0. to 00.0 sec. Cool-side proportional cycle time : 0. to 00.0 sec. anual reset : -00.0 to +00.0% of proportional band Output at reset : -.0 to +0.0% (Heat and cool sides are individual setting.) Overlap/deadband reference : 0.0 to.0 (heating reference at zero) Undershoot suppression factor (USS) for cooling : 0.000 to.000 Ramp/soak stabilizer (RSS) : 0.0 to.0 Selectable from enabled/disabled. Level-PI a) umber of levels: 8 levels (PI groups to 8) b) Level setting range: Low limit of input range to high limit of input range (level settings to 7) otor Valve Control (position proportioning control type only) otor time : to 000 sec. (full open to full close) Integral output limiter : OFF, 0. to 00.0% of control motor time eutral zone : 0. to 0.0% ifferential gap : 0% of neutral zone (Fixed) Valve action at state : a) CLOSE : OFF, OPE : OFF b) CLOSE : O, OPE : OFF c) CLOSE : OFF, OPE : O a), b), c) is selectable. ±0.0% of reading or input sampling time (Whichever is larger) ax. 0 segments Up to 99 segments per pattern. Supplied with hold, step, fast forward, fast rewind features 0 hr 0 min to 00 hs 00 min or 0 min 0 sec to 00 min 0 sec to 9999 repeats Repeat is disabled when set to. to 0000 repeats Continuous repeat when set to 0,000 0 to 99 patterns o pattern link when set to zero Pattern End Output ime : 0 hr 0 min to 00 hs 00 min or 0 min 0 sec to 00 min 0 sec Output remains on when set to zero. ime Signal emory group umber 0 to 6 o assigned groups when set to zero. Program Starting ode a) Starts from a desired value ( after reset) b) Starts from a desired measured input (ime fixed) c) Starts from a desired measured input (ime shortened) d) Intersection of measurement input and pattern is searched and starts from there. (HOL status when started) e) Intersection of measurement input and pattern is searched and starts from there. (RU status when started)
WAI Status at he ime of Program Start WAI condition memory number : 0~8 o WAI when set to zero. Selectable from release by wait zone, contact input (trigger), and timeout. WAI Function : a) Wait zone (upper) ) emperature input: 0 (0.0/0.00) to 00 (00.0/00.00) ( C, F) ) Voltage/current input: 0.0 to 0.0% of input span Wait function off when set to zero b) Wait zone (lower) ) emperature input: -00(-00.0)~0(0.0) ( C, F) or -99.99~0.00 ( C, F) ) Voltage/current input: 0.0~0.0% of input span Wait function off when set to zero c) Wait timeout (ime counting resumes unconditionally after the set time has elapsed) 0 hr 0 min to 00 hs 00 min or 0 min 0 sec to 00 min 0 sec Function is disabled when set to zero. Pattern End Output : O can be assigned (turns on for 0. second for each pattern repeat. ime Signal Output : ime signal or segment signal, whichever is specified. a) ime signal ) umber of outputs: 8 (S to S8) ) Output assignment: Up to (including relays), assignable by O ) ime signal memory group: 6 groups ) umber of memory storage: 6 groups X 6 memories ) umber of storage memory: to segment o. (max = 99) 6) Starting time: 0 hr 0 min to 00 hs 00 min or 0 min 0 sec to 00 min 0 sec 7) Ending segment: to segment o. (max = 99), however, ending segment must be equal to or larger than the starting segment. 8) Ending time: 0 hr 0 min to 00 hs 00 min or 0 min 0 sec to 00 min 0 sec b) Segment signal: S to S8 can be independently turned O and OFF at each segment. Programmed Preset anual Output (Output program Function) Fixed value is produced at each segment. he function is activated by assigning outputs to to the program output. a) umber of output program patterns: to (8/max. segments number) For example, in case of 99 segments, it is "". ax. segment o.: umber of segments by number of patterns multiplied by number of segments. b) Setting items: Output program to : -.0 to +0.0% (Independently adjustable). Other Features : Pattern/segment copy function, tag name edit function (for each pattern), data clear (to initial state), remaining time display of pattern. emory Group PI emory a) emory group o : 0 to 8 (Level-PI is activated when set to zero.) b) Setting items: Proportional band, Integral time, erivative time, Control response parameter, Cool side proportional band, Cool side integral time, Cool side derivative time, eadband/overlap, eutral zone, anual reset, Output limiter (high/low), Cool side output limiter (high/low), O/OFF differential gap (high/low), LBA time, LBA headband Event emory a) emory group o.: 0 to 8 (event off when set to zero) b) Setting items : Event to Segment Wait emory a) emory group o.: 0 to 8 (wait off when set to zero) b) Setting items: wait zone, wait release trigger, timeout for wait ime Signal emory a) emory group o.: 0 to 6 (time signal off when set to zero) b) emory o. : ~6 (6 set points per group) c) Setting items: ime signal output destination, starting segment, time signal starting time, end segment, time signal end time. Program pattern output a) Pattern os.: to (8/max.segment). Up to 99 segments b) Segment o.: to max segment value. c) Setting items : Output program to Before transfer ode Selection Operation ode Reset (), program (RU), fixed setpoint control (FIX), and manual control (A) Action when operation mode is selected. After transfer ode transfer Reset mode Program control Fixed setpoint anual control Control starts with Reset mode Control continues with the the control output at calculated value of the control. reset as the manual setpoint. Program control mode Fixed setpoint control anual control Provide control output at the time of reset * Control continues with the for a program control. Control continues with the for a fixed setpoint control. Control continues after bumpless transfer to manual output Output continues after adjusting the final output level of the program control to the output level of manual. Output continues after adjusting the final output level of the fixed setpoint control to the output level of manual. * Program status is retained unless the instrument is reset. If program control is selected, control starts from the retained status. Output may result in a bump in spite of a bumpless transfer action if the selected control mode is P action, P action, or O/OFF action. Output (OU) umber of ain Output Up to points (OU to OU) Output Function Control output (V), Output program, Retransmission output. OU and OU can be used as event outputs. See output assignment table for details. Output ype Relay output : Voltage pulse output : Current output : Form A contact, 0V AC A (resistive load) 0/V C (Load resistance : ore than 600Ω, 0mA or less) * OU can be more than 00Ω (0mA or less) if OU is not used to 0mA C, 0 to 0mA C (Load resistance : Less than 600Ω) Continuous voltage output : 0 to V C, to V C, 0 to 0V C 0 to V C (Assignable to OU only) (Load resistance : ore than kω) SSR (riac) output : Rated current : 0.A Open collector output : (Sink type) igital Output Load voltage : Less than 0V C, aximum load current : Less than 00mA O voltage : Less than V C (at 00mA) O to O : Standard O to O: Optional umber of Output Up to points (Oup to (O to ) O to : Relay contact output (Standards) O to : Open collector output Output Items ime signal, event, Heater break alarm, Loop break alarm, abnormality, RU state, FIX mode state, A mode status, Ramp status, Soak status, HOL status, WAI status, Pattern end status, A status, FAIL, Communication failure, FBR input abnormality Output ype a) Relay contact output, Form a contact, 0VAC A (Resistive load) b) Open collector output (sink type), Load voltage: 0V C or less Allowable load current : 00mA O voltage : V or less (For maximum load current) Event (Alarm) umber of Event Setting Up to points (Event to ) Event type Process, eviation, Band,, V Setting range eviation : - ( span) to + (input span) Process, Set value : ifferential gap : 0 to input span Same as input range ifferential gap : 0 to input span V value : -.0 to +0.0% ifferential gap : -.0 to +0.0% Output Freely assignable to digital outputs (O to, OU, OU). See Output allocation table for details Optional _0E
Other a) Hold function (Valid when power is supplied or when even is started.) b) Event action selection at the time of abnormal input. c) Action selection at the time of d) elay timer: 0.0 to 600.0 sec. e) Event minimum O and OFF time : 0.0 to 600.0 sec (O/OFF individual setting) f) Interlock : Without/With/Switches into the manual mode and stops control. Heater break alarm (HBA) a) umber of C input: points ( for each C input) b) function: Current detector (C) c) range: CL-6-P-: 0 to 0A CL--S6-0L-: 0 to 00A d) Heater current display range:0.0 to00.0a e) Heater current display accuracy: ±% of input value or ±A f) Interlock : Without/With/Switches into the manual mode and stops control. g) Output method: Freely assignable to digital outputs h) Action selection at reset status Heater break alarm (HBA) is not available for current/continuous voltage output. Loop break alarm (LBA) a) LBA time: 0 to 700 sec. (OFF when set to zero) b) LB setting: 0 to input span c) Interlock : Without/With/Switches into the manual mode and stops control. d) Output method: Freely assignable to digital outputs See output assignment table. Loop break alarm (LBA) is not available for heat/cool PI control type. Analog Retransmission Output umber of Outputs Up to points ( for program outputs) epends on output assignment. Output types easured value (), eviation (EV), Set value (), anipulated output value (V), Output program value, % of segment time (Selectable) Output Signal Current output : to 0mA C, 0 to 0mA C (Load resistance : Less than 600Ω) Continuous voltage output : 0 to V C, 0 to V C, to V C, 0 to 0V C (Load resistance : ore than kω) Scaling Range a), : Same as input range b) Control output, Output program output: 0 to 00% c) eviation: ±input span Output program and segment time percentage are fixed. Additional Function Stop/continue selectable during status igital (I to 6 : Optional, I 7 to : Standard) umber of s Up to points (I to 6, I 7 to ) Rating on-voltage contact input I to I6 : Pattern o. selection + Pattern set, WAI release I7 to I : Pattern o selection + Pattern set, ode selection (, RU), irect/reverse action selection Refer to igital table for details. Communication Communication method : Communication speed : [CO] RS-8, RS-C, RS-A 00, 9600, 900, 800, 7600 bps Selectable Protocol : RKC standard (ASI X.8. A) OBUS RU Selectable Bit format Start bit : ata bit : 7 or 8 For OBUS 8 bit only Parity bit : Without, Odd or Even Stop bit : or aximum connection : RS-8/RS-A : units (Including host) RS-C : unit Inter-Controller Communication Communication type : Communication method : Communication speed : Protocol : Function to send target value to slave controllers RS-8 9600, 900, 800 bps Selectable OBUS RU [CO] Bit format : Start bit :, ata bit : 8 Parity bit : Without, Stop bit : aximum slaves : units aximum slaves : /PF90/FB series (With memory area) RB series (Without memory area) Loader Communication Communication method : RS-8 Communication speed : 800 bps Protocol : RKC standard (ASI X.8. A) Bit format : Start bit :, ata bit : 8 Parity bit : Without, Stop bit : Connection method : Front: Connected to CO-K with an exclusive cable (W-BV-0-00) Front loader interface is available only while instrument is powered. Feedback Resistance (FBR) Resistance value Standard : 00 to 0kΩ (factory default Ω) [CO] Sampling time 0. sec (with measuring input sampling time of 0.0 sec) 0. sec (with measuring input sampling time of 0. sec) 0. sec (with measuring input sampling time of 0. sec) Position proportional control can be used with/without FBR (feedback resistance) input. General Supply Voltage a) 8 to 6V AC (Including supply voltage variation) [Rating : 00 to 0V AC] (0/60Hz selectable) b) 0. to 6.V AC (Including supply voltage variation) [Rating : V AC] (0/60Hz selectable) c) 0. to 6.V C (Ripple rate 0% p-p or less) [Rating:VC] Power Consumption a) 00 to 0V AC :.VA <0.9VA> ( at 0V AC), 9.VA <7.VA> (at 00V AC) b) V AC : 8.VA <6.VA> c) V C : 0mA <7mA> < > : Power saving mode Rush Current a) 00 to 0V AC : Less than 7.A (at 0V AC), Less than 7.A (at 00V AC) b) V AC : Less than 8.A c) V C : Less than 6.0A Power Failure Effect A power failure of 0m sec or less will not affect the control action. If power failure of more than 0m sec occurs, controller will restart with the state of HO start, HO start or COL start (selectable) Power Saving ode If any key is not pressed during the user set time period, the backlight LE is turned off except and AL displays. Setting time: 0 to 60 min (0 for no power saving mode) Back to normal display if any key is pressed during the power saving mode. Waterproof/ustproof : EA type : IP (When mounted in a panel, front direction) Operating Environments : -0 to C [ to F] to 9% RH. Absolute humidity : AX. W.C 9.g/m dry air at 0.kPa. emory Backup : Backed up by non-volatile memory (FRA) ata retaining period : Approx. 0 years umber of writing : Approx. 0,000,000,000 times. (epending on storage and operating conditions.) et Weight : Approx. 70g External imensions (W x H x ) : 96 x 96 x 80mm _0E
Quick start code odel and Suffix ( : Green, : Orange, Pattern : White) odel PF90 ( : White, : White, Pattern : White) * Relay contact output Output (OU) Voltage pulse output : 0/V C V Control output or C ma, V (See Output Signal able, : to 8) Output program riac (SSR) output Open collector output o supplied Output (OU) * Relay contact output Control output, Voltage pulse output : 0/V C V Output program, Retransmission C ma, V (See Output Signal able, : to 8) output riac (SSR) output or igital output Open collector output Output (OU) * o supplied Output program, Voltage pulse output : 0/V C V Retransmission output C ma, V (See Output Signal able, : to 8) or igital output Open collector output Power supply V AC/C 00 to 0V AC igital output O: points, Relay : O to O: points, Relay O to, Open collector: O to *, * one C input or C input: points FBR input FBR (FeedBack Resistance) input ot supplied Communication CO:RS-C CO:ot supplied igital input: 6 points, I to 6 <ote > CO:RS-A CO:ot supplied igital input: 6 points, I to 6 igital input CO:RS-8 CO:ot supplied igital input: 6 points, I to 6 (I to 6) CO:RS-C CO:RS-8 igital input: 6 points, I to 6 I7 to supplied CO:RS-8 CO:RS-8 igital input: 6 points, I to 6 as standard CO:ot supplied CO:RS-8 igital input: 6 points, I to 6 igital input: 6 points, I to 6 o quick start code (efault setting) Initial setting Specify quick start code Specify quick start code and o quick start code PI control with A (Reverse action) PI control with A (irect action) Heat/Cool PI control with A Control ethod Heat/Cool PI control with A for extruder (Air cooling type) Heat/Cool PI control with A for extruder (Water cooling type) Position proportional PI control with A (Reverse action) Position proportioning PI control with A (irect action) and range o quick start code See range able Instrument version Version symbol range code table hermocouple K J E K K K K 09 K K 0 K 06 K C9 K B K A K C J 7 J 9 J 6 J J C9 J B J B6 J B9 E 0 E 7 E 08 E 06 E B E A6 E B Range -00.0 to +00.0 C -00.0 to+7.0 C 0.0 to 00.0 C 0.0 to 00.0 C -00 to +7 C 0 to 00 C 0 to 00 C -8.0 to +0.0 F 0.0 to +00.0 F 0.0 to 800.0 F -8 to +0 F -00.0 to +00.0 C -00.0 to+00.0 C 0.0 to 00.0 C -00 to +00 C -8.0 to +9.0 F 0.0 to 00.0 F 0.0 to 800.0 F -8 to +9 F -00.0 to +000.0 C -00.0 to +00.0 C 0.0 to 000.0 C -00 to +000 C -8.0 to +8.0 F 0.0 to 800.0 F -8 to +8 F Output signal code table S R B 9 06 6 C B7 A7 C9 S 0 S 07 S 06 S A8 S A S A7 R 0 R 08 R 07 R A8 R A R A7 B 0 B 0 B A9 B B B B 0 0 A8 A A7 Range -00.0 to -00.0 to +00.0 C +00.0 C 0.0 to 00.0 C -00 to +00 C -8.0 to -00.0 to +7.0 F +700.0 F 0.0 to 700.0 F -8 to +7 F 0.0 to 700.0 C -0.0 to +768.0 C -0 to +768 C -8.0 to +.0 F 0.0 to 00.0 F -8 to + F 0.0 to 700.0 C -0.0 to +768.0 C -0 to +768 C -8.0 to +.0 F 0.0 to 00.0 F -8 to + F 0.0 to 800.0 C 0 to 800 C 0.0 to 00.0 F 0.0 to 7.0 F 0 to 7 F 0.0 to 00.0 C 0 to 00 C 0.0 to 7.0 F 0.0 to 00.0 F 0 to 7 F odel and Suffix Hardware coding Quick start only code A 06 A 0 PLII A 0 (BS) A A7 A A A A W 0 W 06 W 0 WRe/W6Re W A8 (AS) W A6 W A L 0 L L 0 (I) L A6 L B L A U 0 U 08 U U B (I) U B U B F 0 F 0 PR0-0 F A F A o code F G A W Z C o code 0 - V C * 0 - V C 0-0V C 6 - V C 7 0-0mA C 8-0mA C * : 0 to V C output can be specified only for Output (Analog retransmission output). C F W X Y Y Y Range 0.0 to 90.0 C 0.0 to 00.0 C 0 to 90 C 0.0 to.0 F 0.0 to 00.0 F 0 to F 0.0 to 00.0 C 0.0 to 00.0 C 0 to 00 C 0.0 to 00.0 F 0.0 to 00.0 F 0 to 00 F 0.0 to 900.0 C 0 to 900 C 0.0 to 600.0 F 0.0 to 6.0 F 0 to 6 F 0.0 to 600.0 C 0 to 600 C 0.0 to 00.0 F 0.0 to.0 F 0 to F 0.0 to 800.0 C 0 to 800 C 0.0 to 00.0 F 0 to 00 F <ote > If inter-controller communication (master-slave operation) is used, select code: W, X, or Y (that means "with communication ") for a master device, and or X (communication : RS-8) for a slave device. * For program or retransmission output, specify voltage or current. For digital output, specify relay or open collector output. * Heater break alarm (HBA) is not available for current/continuous voltage output. Loop break alarm (LBA) is not available for heat/cool PI control type. * Position proportional control can be used with/without FBR (feedback resistance) input. Control output (OU, OU) assignment by control action PI control action: Control output is produced from OU. OU can be used as retransmission output or digital output. Heat/Cool PI control action: Heating output is produced from OU and cooling output from OU. Position proportioning PI control action: Opening output is produced from OU and closing output from OU. R Range -00.00 to+0.00 C -00.0 to +80.0 C -00.0 to +00.0 C -00.0 to +600.0 C Pt00 6-00 to +80 C C9-8.0 to +6.0 F B8-00.0 to +00.0 F -8 to +6 F P 9-00.00 to+0.00 C P -00.0 to +00.0 C JPt00 P 6-00.0 to +600.0 C P 0-00.0 to +60.0 C P 0 0.0 to 00.0 C P -00 to +60 C C Current Voltage 0 to 0mV 0 to 00mV 0 to V 0 to V 0 to 0V to V 0 to 0mA to 0mA -00 to +00mV - to +V -0 to +0mV -0 to +0V - to +V 0 0 0 0 0 6 0 7 0 8 0 9 0 9 0 9 0 9 0 9 0 Range -9999 to +000 (Programmable) Factory set value: 0.0 to 00.0% 6 _0E
Quick Start Quick start code tells the factory to ship with each parameter preset to the values detailed as specified by the customer. Quick start code is not necessarily specified when ordering, unless the preset is requested. hese parameters are software selectable items and can be re-programmed in the field via the manual. Quick start code (Initial setting code) igital output code table (Programmable) igital input allocation igital output type igital output type igital output type igital output type C : CL-6-P-, C : o use C types C : CL--S6-0L-, C : o use C : CL-6-P-, C : CL-6-P- C : CL--S6-0L-, C : CL--S6-0L- ot supplied Communication ASI/RKC standard OBUS CO is used exclusively for inter-controller communication. igital allocation table Ramp/Soak Process/emperature Controller See igital Allocation table See igital output code table See igital output code table See igital output code table See igital output code table o C and C efault setting value of igital output type igital output : eviation High igital output : eviation Low with Hold igital output : ime signal igital output : Pattern end output * Heater break alarm (HBA) is not available for current/continuous voltage output. * Loop break alarm (LBA) is not available for heat/cool PI control type. PS U Event types o event eviation High A eviation Low eviation High/Low (Common high/low setting) Band (Common high/low setting) eviation High with Hold eviation Low with Hold B C E F eviation High/Low with Hold (Common high/low setting) Process High Process Low Process High with Hold G H J K Process Low with Hold L Heater Break Alarm (HBA) * P Heater Break Alarm (HBA) * Q Loop Break Alarm (LBA) * R FAIL S FBR Abnormality Band (Individual high and low settings) U Set value High V Set value Low W eviation High/Low (Individual high and low settings) X eviation High/Low with Alarm Hold (Individual high and low settings) Y V value High V value Low Cool side V value High Cool side V value Low ime signal ime signal ime signal ime signal Pattern end output 6 7 8 9 0 I I I I I I6 I7 I8 I9 I0 I Pattern o. Selection Pattern o. Set RU SEP HOL Pattern o. Selection Pattern o. Selection Pattern o. Set RU SEP Pattern o. Selection WAI release WAI release WAI release WAI release WAI release WAI release Pattern o. Selection Pattern o. Set WAI release WAI release WAI release WAI release WAI release WAI release Pattern o. Selection WAI release WAI release WAI release WAI release WAI release WAI release RU SEP HOL irect/reverse selection WAI release WAI release WAI release WAI release WAI release WAI release RU SEP HOL Pattern o. Selection (Increment) Example of odel and Quick start code : hermocouple PR0-0, ax.800 C, resolution 0. C Control: Heating control (Output: to 0mA C) igital output : points (Relay contact output) igital output : eviation high, igital output : Pattern end output igital output : ime signal output, igital output : ime signal output odel code OU (Heat output) : to 0mA C : 8 OU (Cool output) : one : OU (Retransmission) : 0 to 0V C : Supply voltage igital output: Relay (event) points (O to ) : C/FBR input: one : -8- *W-FF0 Quick start code igital input : WAI release, P.o Select, P o.set igital output : eviation high : A igital output : Pattern end output : 9 igital output : ime signal : igital output : ime signal : 6 : Retransmission output: 0 to 0V C ime signal output: 8 points (open collector) igital input: WAI release + Pattern o.selection, (With Pattern o.set) Communication: RS-C (OBUS) + inter-controller communication -A96- /Scale range : PR0-0 0.0 to 800.0 C : F0 Control action: PI with A (reverse) : F Specify quick start code : Communication/igital input: : W I7 to as standard CO: RS-C, CO : Inter-controller I : 6 points (I to 6) CO protocol : C type : one OBUS : : Accessory Current transformer for heater break alarm (HBA) odel code CL-6-P- (0 to 0A) CL--S6-0L- (0 to 00A) CL-6-P- Approx.0. (Unit : mm) CL--S6-0L- Approx.00 0 erminal Cover (two pieces necessary) odel code : KFB00-0 0 φ.8 0 7. φ epth _0E 7
External imensions and Rear erminals (erminal cover) Unit : mm 9.8 Panel cutout 96 9.8 06. 9 +0.8 0 0 96 80 90..0 (Rubber packing) 9 +0.8 0 (Panel thickness: to 0mm) Please use solderless terminal with width smaller than.9mm. Unused terminals are not supplied with screws. 6 7 8 9 0 7 8 9 0 6 7 8 6 7 8 9 0 6 6 7 8 9 0 o. 6 7 8 CO CO 9 C 0 C I 7 I 8 I 9 I0 I 0 RU SEP RU SEP () () () Ptn. o () () () Ptn. o HOL () Ptn. (8) (8) () Ptn.o. (6) o Ptn. SE (6) Open (O) C,C inputs (W) Close (C) RU SEP HOL ir/rev RU SEP HOL Ptn. IC igital inputs (I 7 to ) Standard Feedback resistance A B B () () () easuring input ()hermocouple ()R ()Voltage/Current o. AC L C 00-0V V V CO O O O O 6 CO 7 O O 8 O O 9 O riac 0 () () () () Power supply Standard igital outputs, (O, ) Relay contact output Standard igital outputs, (O, ) Relay contact output Output (OU) () Relay output () Voltage pulse/voltage/current () SSR (riac), () Open collector o. 7 8 9 0 6 CO (-) O O 6 O 7 O 8 CO(-) O 9 O0 O O igital outputs to 8 (O to 8) Open collector output igital outputs 9 to (O 9 to ) Open collector output o. 6 SG S SG /R(A) SG CO (A) SG CO Communication () RS-C RS-8 * R /R(B) (B) () RS-8 7 () () () RS-A 8 R(A) /R(A) Communication 9 R(B) () /R(B) (Inter-controllers) 0 CO : 0, :,,, I I I () () () Pattern o. WAI release WAI release WAI release igital inputs (I to 6) I (8) WAI release O () () riac () () Output (OU) () Relay output () Voltage pulse/voltage/current () SSR (riac), () Open collector 7 8 () () Output (OU) () Voltage pulse/voltage/ Current () Open collector 6 I I 6 (6) Pattern SE WAI release WAI release * : o use communication (inter-controller communication). please specify RS-C or RS-8 for communication. 8 _0E