Thanks for your purchase of a Union Hill IronWorks Fixture. We take pride in handcrafting each piece in the USA. To make your install experience as easy as possible, we ve put together customized instructions for every fixture. To find your fixture, click on the links below to take you to the right place and scroll through the pictures. UNION HILL IRONWORKS -Wall Lights -Ceiling Lights If you have any questions or cant find your light fixture, please don t hesitate to reach out and let us know. We can be reached at info@westninthvintage.com. Thanks so much for being our customer. Sincerely, Frank Iannucci Owner, West Ninth Vintage
WOOD PULLEY INSTALL INSTRUCTIONS: ITEM: ALL WOOD PULLEYS Included: 5 ceiling plate, 4 of Vintage Twisted Wire, 2x Black Cages. STEP 1: Remove all items from their packaging and get a qualified electrician. STEP 2: Lay out items on the ground so that they match the 1 st picture below (next page). STEP 3: Take the black sockets with vintage twisted wire (A) and weave through middle bar (B) and then repeat with other socket (A) STEP 4: Take chain/hanger (D) and hook on to pulley hook (E). STEP 5: Bring wires together and Weave vintage twisted wire through chain. Prior to running the cord through the hook and nipple (F), make any adjustments to the cord lengths and chain on how high or low you will want them to hang when you attach it to the ceiling. STEP 6: Once you have made your final adjustments to the pulley and cord lengths, any additional cord will be run through the hook and nipple (F). Unweave the additional cord and straighten the wires as best you can. (This will allow the wires to pass easier through the hook and nipple) STEP 7: (Reference Picture 2 on Next Page) Pass the excess straightened vintage wires through the hook and nipple (F). Once all the excess wire is through, take the hook and nipple (F) and pass through ceiling canopy hole (G). When the nipple is through the canopy, connect crossbar to the nipple on the backside of canopy and spin crossbar down to tighten to ceiling canopy. (See Picture 2 on Next Page) STEP 8: The entire piece should be in one unit now. This will now be connected to your electrical box. (It is recommended at this point that an additional person be asked to hold the pulley during the connection to ceiling box). Remove the two 3 screws from the package. Take one screw and place through hole H (either hole is fine). This screw should then be connected to your electrical box but only screw in roughly 1 (See Picture 2 on Next Page). Repeat with second screw and other hole H. This will now hold the entire piece in place and will leave 2 of space to connect the wiring). STEP 9: Connect your electrical, test light and then finish screwing 3 screws into place to raise light to ceiling
PICTURE 1 D. F. B. E. H. G. H. A. A. PICTURE 2
BARN PULLEY INSTALL INSTRUCTIONS: SKU: ALL METALL PULLEYS Included: 5 ceiling plate, 4 of Vintage Twisted Wire, 2x Black Cages STEP 1: Remove all items from their packaging and get a qualified electrician. STEP 2: Lay out items on the ground so that they match the 1 st picture below (next page). STEP 3: Take the black sockets with vintage twisted wire (A) and weave through middle bar (B) and then follow the pulley wheel up through top middle bar (C) (repeat with opposite pulley wire so that they cross through (C)). STEP 4: Take chain/hanger (D) and hook on to pulley hook (E). STEP 5: Bring wires together and Weave vintage twisted wire through chain. Prior to running the cord through the hook and nipple (F), make any adjustments to the cord lengths and chain on how high or low you will want them to hang when you attach it to the ceiling. STEP 6: Once you have made your final adjustments to the pulley and cord lengths, any additional cord will be run through the hook and nipple (F). Unweave the additional cord and straighten the wires as best you can. (This will allow the wires to pass easier through the hook and nipple) STEP 7: (Reference Picture 2 on Next Page) Pass the excess straightened vintage wires through the hook and nipple (F). Once all the excess wire is through, take the hook and nipple (F) and pass through ceiling canopy hole (G). When the nipple is through the canopy, connect crossbar to the nipple on the backside of canopy and spin crossbar down to tighten to ceiling canopy. (See Picture 2 on Next Page) STEP 8: The entire piece should be in one unit now. This will now be connected to your electrical box. (It is recommended at this point that an additional person be asked to hold the pulley during the connection to ceiling box). Remove the two 3 screws from the package. Take one screw and place through hole H (either hole is fine). This screw should then be connected to your electrical box but only screw in roughly 1 (See Picture 2 on Next Page). Repeat with second screw and other hole H. This will now hold the entire piece in place and will leave 2 of space to connect the wiring). STEP 9: Connect your electrical, test light and then finish screwing 3 screws into place to raise light to ceiling
PICTURE 1 A. B. PICTURE 2
Reclaimed Wood Chandelier: SKU: 236191138,232758001,229442567 Included: 4.25 Ceiling Plate STEP1: Remove all items from their packaging. Step 2: Screw in Ceiling Canopy (A) to steel Pipe (B) Step 3: Run main wire through Steel Pipe (B) and out the ceiling canopy (A) Step 4: Screw in Steel Bar (B) to wood base Canopy (C). STEP 3: Connect electrical wires on back of Ceiling Plate (A) to existing power source. Connect your ground wire to the green grounding screw. STEP 4: Use two mounting screws included to mount Ceiling Plate (A) to your electrical box. STEP 5: Wrap sockets and cord around Wood Beam as much or as little as you want. A. B. C.
Reclaimed Wood Light: SKU: 238127065 Included: 4.25 Ceiling Plate STEP1: Remove all items from their packaging. Step 2: Screw in Ceiling Canopy (A) to steel Pipe (B) Step 3: Run main wire through Steel Pipe (B) and out the ceiling canopy (A) Step 4: Screw in Steel Bar (B) to wood base Canopy (C). STEP 3: Connect electrical wires on back of Ceiling Plate (A) to existing power source. Connect your ground wire to the green grounding screw. STEP 4: Use two mounting screws included to mount Ceiling Plate (A) to your electrical box. A. B. C.
Reclaimed Wood Ceiling Fixture: SKU: 233491089, 233519780 Included: 4.25 Ceiling Plate STEP1: Remove all items from their packaging. Step 2: Screw in Ceiling Canopy (A) to steel Pipe (B) Step 3: Run main wire through Steel Pipe (B) and out the ceiling canopy (A) Step 4: Screw in Steel Bar (B) to wood base Canopy (C). STEP 3: Connect electrical wires on back of Ceiling Plate (A) to existing power source. Connect your ground wire to the green grounding screw. STEP 4: Use two mounting screws included to mount Ceiling Plate (A) to your electrical box. STEP 5: If you purchased the version with cages, remove screws on cage and fit around Sockets. Tighten them into place using screws A. B. C.
U Shaped Pendant Chandeliers W/ Porcelin Sockets: SKU: 237951118 Included: 5 Ceiling Plate Step 1: Remove all items from their packaging and lay out on a table or flat surface to match picture below. STEP 2: Connect electrical wires on back of ceiling plate(a) to existing power source. Connect your ground wire to either screw on the custom clip on the backside of the ceiling plate to ground the entire fixture. STEP 3: Use two mounting screws included to mount Ceiling Plate (A) to your electrical box. (There are two holes in the Ceiling Plate that line up with the holes in your electrical box) STEP 4: Take the two Identical Arms (B) and screw them together. Next, Screw The ceilings mounts (C) into the corner elbows (D). You can now mount this to the ceiling however you want using the ceiling anchors included. STEP 5: Wrap Cord around bar as much or as little as you want. C. B. A. B. C. D.
U Shaped Pendant Chandeliers W/Steel Sockets: SKU: 227529516 Included: 5 Ceiling Plate Step 1: Remove all items from their packaging and lay out on a table or flat surface to match picture below. STEP 2: Connect electrical wires on back of ceiling plate(a) to existing power source. Connect your ground wire to the green grounding screw on the back of the ceiling plate. STEP 3: Use two mounting screws included to mount Ceiling Plate (A) to your electrical box. (There are two holes in the Ceiling Plate that line up with the holes in your electrical box) STEP 4: Take the two Identical Arms (B) and screw them together. Next, Screw The ceilings mounts (C) into the corner elbows (D). You can now mount this to the ceiling however you want using the ceiling anchors included. STEP 5: Wrap Cord around bar as much or as little as you want. C. B. A. B. C. D.
Porcelain Pendant Chandelier: Included: 5 Ceiling Plate STEP1: Remove all items from their packaging. Step 2: Remove all items from their packaging and lay out on a table or flat surface to match picture below. STEP 3: Use custom clip (A) that is built into ceiling plate (B) to adjust the heights of your individual pendants. Once you find your desired heights, lock pendants into place STEP 4: Connect electrical wires on back of ceiling plate(b) to existing power source. Connect your ground wire to either screw on the custom clip to ground the entire fixture. STEP 5: Use two mounting screws included to mount Ceiling Plate (B) to your electrical box. (There are two holes in the Ceiling Plate (B) that line up with the holes in your electrical box) STEP 6: If you purchased the version with cages, remove screws on cage and fit around Sockets. Tighten t hem into place using screws B. A.
Porcelain Pendant SWAG Chandelier: SKU: 224028385, 224027191 Included: 5 Ceiling Plate STEP1: Remove all items from their packaging. Step 2: Remove all items from their packaging and lay out on a table or flat surface. STEP 3: Use custom clip (A) that is built into ceiling plate (B) to adjust the heights of your individual pendants. Once you find your desired heights, lock pendants into place STEP 4: Connect electrical wires on back of ceiling plate(b) to existing power source. Connect your ground wire to either screw on the custom clip to ground the entire fixture. STEP 5: Use two mounting screws included to mount Ceiling Plate (B) to your electrical box. (There are two holes in the Ceiling Plate (B) that line up with the holes in your electrical box) STEP 6: If you purchased the version with cages, remove screws on cage and fit around Sockets. Tighten them into place using screws STEP 7: Use Ceiling Clips (C) to attach wire to ceiling however you would like. B. C. A.
Wine Bottle Light: SKU: 223435914 Included: 5 Ceiling Plate, STEP1: Remove all items from their packaging. Step 2: Unscrew Pendant Wire Strain Relief Cap (A) (Just the Cap) and slide Cap (A) onto Pendant Wire (B) Step 3: Take Pendant Wire (B) and put through center of ceiling canopy (C) where cap (A) was just screwed off. Step 4: Once you have adjusted the pendant wire (B) to your desired length, Screw back on your Strain Relief Cap (A) to tighten down and hold the pendant wired (B) in place Step 5: Connect electrical wires on back of Ceiling canopy (C) to existing power source. Connect your ground wire to the T-Bar where it says GND for Ground. STEP 6: Use two mounting screws included to mount Ceiling Plate (C) to your electrical box. A. C B.
Wood And Steel Wall Pulley Light: SKU: 238097416, 238527226 Included: Cast Iron Wall Mount, Wood and Steel Wall Pulley, Anchors STEP1: Remove all items from their packaging. Step 2: Screw Wall Plate (A) Into wall with 2x Screws and Anchors STEP 3: Take Cord (B) (Plug end) and wrap around Pulley Wheel (C) as many times as you want to get to your desired height. Once you have found desired length, plug into outlet. B. A. C.
Wood and Steel Single Wall Lights: SKU: 237949705, 238049174, 238048492, 237948679 STEP1: Remove all items from their packaging and lay out on a table or flat surface to match picture below. Step 2: Find the T-Bar, unscrew from nipple (do not remove nipple from wood) and connect T-Bar to your electrical box with two mounting screws included. Step 3: Once the T-bar is attached tightly to your electrical box, connect your ground wire to the T-bar where it says GND for Ground. Next, connect the electrical wires on the back of the light to your existing power source. Step 4: Once the electrical is connected, Screw nipple You may need to use pliers to tighten into place using nipple cap (A) into the T-bar and tighten. Step 6: If you purchased the version with a cage, remove screws on cage and fit around steel socket. (screws not necessary to keep cage on socket ) A. A.
Wood and Steel Wall Lights: SKU: 235150500, 235150684, 235116203, 235148598 STEP1: Remove all items from their packaging and lay out on a table or flat surface to match picture below. Step 2: Find the T-Bar, unscrew from nipple (do not remove nipple from wood) and connect T-Bar to your electrical box with two mounting screws included. Step 3: Once the T-bar is attached tightly to your electrical box, connect your ground wire to the T-bar where it says GND for Ground. Next, connect the electrical wires on the back of the light to your existing power source. Step 4: Once the electrical is connected, Screw nipple You may need to use pliers to tighten into place using nipple cap (A) into the T-bar and tighten. Step 5: If you purchased the version with cages, remove screws on cage and fit around steel socket. (screws not necessary to keep cage on socket ) A.
Steel Ship Light: SKU: 238979622 STEP1: Remove all items from their packaging and lay out on a table or flat surface to match picture below. Step 2: Screw Wall Plate (A) into the back of Steel Mount (B). STEP 3: Connect electrical wires on back of Wall Plate (A) to existing power source. Connect your ground wire to the green grounding screw. STEP 4: Use two mounting screws included to mount Wall Plate (A) to your electrical box. B. A.