TCMT16, TCMT46, TCMT466 Optocoupler, Phototransistor Output, AC Input, Single / Quad Channel, Half Pitch Mini-Flat Package FEATURES Low profile package (half pitch) 22775 22628-1 C E 9 AC isolation test voltage 375 V RMS Low coupling capacitance of typical.3 pf Low temperature coefficient of CTR Wide ambient temperature range Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 1 2 8 A 4 PIN C 16 PIN DESCRIPTION The low profile miniflat package includes an optocoupler with AC Input and transistor output. It is available in single channel (4 pin) TCMT16 or quad channel (16 pin) TCMT46. APPLICATIONS Programmable logic controllers AGENCY APPROVALS UL1577, file no. E76222, double protection cul component acceptance service no 5A, double protection DIN EN 6747-5-5 (VDA 884-5) FIMKO: FI EN 695-1:26 BSI: BS EN 665:22; BS EN695-1:26 CQC GB 8898-211, GB 4943.1-211 (suitable for installation altitude below 2 m) ORDERING INFORMATION T C M T # 6 # SOP-# PART NUMBER 7 mm AGENCY CERTIFIED/PACKAGE CTR (%) SINGLE CHANNEL QUAD CHANNEL UL, cul, FIMKO, BSI, VDE 8 to 3 8 to 3 1 to 3 SOP-4 TCMT16 - - SOP-4 TCMT16T3 (1) - - SOP-16 - TCMT46 TCMT466 SOP-16 - TCMT46T (1) - Notes Available only on tape and reel. (1) Product is rotated 18 in tape and reel cavity. ABSOLUTE MAXIMUM RATINGS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Forward current I F ± 6 ma Forward surge current t p 1 μs I FSM ± 1.5 A Power dissipation P diss 1 mw Junction temperature T j 125 C Rev. 2.6, 21-Jul-15 1 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 ABSOLUTE MAXIMUM RATINGS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT OUTPUT Collector emitter voltage V CEO 7 V Emitter collector voltage V ECO 7 V Collector current I C 5 ma Collector peak current t p /T =.5, t p 1 ms I CM 1 ma Power dissipation P diss 15 mw Junction temperature T j 125 C COUPLER AC isolation test voltage (RMS) V ISO 375 V RMS Total power dissipation P tot 25 mw Operating ambient temperature range T amb -4 to +1 C Storage temperature range T stg -4 to +125 C Soldering temperature (1) T sld 26 C Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (2) Wave soldering three cycles are allowed. Also refer to Assembly Instructions (www.vishay.com/doc?854). ELECTRICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage I F = ± 5 ma V F - 1.35 1.6 V Junction capacitance V R = V, f = 1 MHz C j - 8 - pf OUTPUT Collector emitter voltage I C = 1 μa V CEO 7 - - V Emitter collector voltage I E = 1 μa V ECO 7 - - V Collector dark current V CE = 2 V, I F = I CEO - - 1 na COUPLER Collector emitter saturation voltage I F = ± 1 ma, I C = 1 ma V CEsat - -.3 V Cut-off frequency V CE = 5 V, I F = ± 1 ma, R L = 1 Ω f c - 1 - khz Capacitance (input to output) f = 1 MHz C IO -.3 - pf Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT TCMT16 CTR 8 3 % I C /I F V CE = 5 V, I F = ± 5 ma TCMT46 CTR 8 3 % TCMT466 CTR 1 3 % Rev. 2.6, 21-Jul-15 2 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 SWITCHING CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Delay time Rise time Fall time Storage time Turn-on time Turn-off time Turn-on time Turn-off time V S = 5 V, I C = 2 ma, R L = 1 Ω V S = 5 V, I C = 2 ma, R L = 1 Ω V S = 5 V, I C = 2 ma, R L = 1 Ω V S = 5 V, I C = 2 ma, R L = 1 Ω V S = 5 V, I C = 2 ma, R L = 1 Ω V S = 5 V, I C = 2 ma, R L = 1 Ω V S = 5 V, I F = ± 1 ma, R L = 1 kω (see figure 2) V S = 5 V, I F = ± 1 ma, R L = 1 kω (see figure 2) t d - 3 - μs t r - 3 - μs t f - 4.7 - μs t s -.3 - μs t on - 6 - μs t off - 5 - μs t on - 9 - μs t off - 18 - μs I F R G = 5 Ω t p T =.1 t p = 5 µs 15234 I F 5 Ω 1 Ω + 5 V I C = 2 ma; Channel I Channel II Adjusted Through Input Amplitude Oscilloscope R L = 1 MΩ C L = 2 pf I F I C 1 % 9 % 1 % t p t d t r t on (= t d + t r ) t p t r t d t on Pulse duration Delay time Rise time Turn-on time t s t f t off t s t f t off (= t s + t f ) t t Storage time Fall time Turn-off time 96 11698 Fig. 1 - Test Circuit, Non-Saturated Operation Fig. 3 - Switching Times I F I F = 1 ma + 5 V R G = 5 Ω t p T =.1 t p = 5 µs Channel I 15235 5 Ω 1 kω Channel II Oscilloscope R L = 1 MΩ C L = 2 pf Fig. 2 - Test Circuit, Saturated Operation Rev. 2.6, 21-Jul-15 3 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Climatic classification (according to IEC 68 part 1) 55/11/21 Comparative tracking index CTI 175 Maximum rated withstanding isolation voltage 4 % to 6 % RH, AC test of 1 min V ISO 375 V RMS Maximum transient isolation voltage V IOTM 6 V Maximum repetitive peak isolation voltage V IORM 77 V Insulation resistance V IO = 5 V, T amb = 1 C R IO 1 11 Ω Isolation resistance (under fault conditions) V IO = 5 V, T amb = T SI R IO 1 9 Ω Output safety power P SO 35 mw Input safety current I SI 2 ma Input safety temperature T SI 175 C Apparent charge test voltage (method A) V IORM x 1.6 = V PR, type and sample test t m = 6 s, partial discharge < 5 pc V PR 1132 V peak Apparent charge test voltage (method B) V IORM x 1.875 = V PR, 1 % production test with t m = 1 s, partial discharge < 5 pc V PR 1326 V peak Creepage distance 5 mm Clearance distance 5 mm Insulation thickness DTI.4 mm Environment (pollution degree in accordance to DIN VDE 19) 2 Note As per IEC 6747-5-5, 7.4.3.8.2, this optocoupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) P tot - Total Power Dissipation (mw) 3 Coupled device 25 2 Phototransistor 15 IR-diode 1 5 4 8 12 96 117 T amb - Ambient Temperature ( C) I F - Forward Current (ma) 1 1 1 T amb = 11 C T amb = 75 C T amb = 25 C T amb = C T amb = -55 C.1.6.8 1. 1.2 1.4 1.6 V F - Forward Voltage (V) Fig. 4 - Total Power Dissipation vs. Ambient Temperature Fig. 5 - Forward Voltage vs. Forward Current Rev. 2.6, 21-Jul-15 4 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 I C - Collector Current (ma) 55 5 I F = 35 ma 45 4 I F = 3 ma 35 I F = 25 ma 3 25 I F = 2 ma 2 I F = 15 ma 15 1 I F = 1 ma I F = 1 ma 5 I F = 5 ma 1 2 3 4 5 6 7 8 9 1 V CE - Collector Emitter Voltage (non-sat) (V) N CTR - Normalized CTR (non-saturated) 1.2 1..8.6.4.2 I F = 5 ma Normalized to CTR value: I F = 5 ma, V CE = 5 V, T amb = 25 C -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) Fig. 6 - Collector Current vs. Collector Emitter Voltage Fig. 9 - Normalized Current Transfer Ratio (non-saturated) vs. Ambient Temperature I CE - Leakage Current (na) 1 1 1 1 1.1.1.1 I F = ma V CE = 4 V V CE = 12 V V CE = 24 V -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) N CTR - Normalized CTR (sat) 1.2 1..8.6.4.2 I F = 5 ma Normalized to CTR value: I F = 5 ma, V CE = 5 V, T amb = 25 C -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) Fig. 7 - Leakage Current vs. Ambient Temperature Fig. 1 - Normalized Current Transfer Ratio (saturated) vs. Ambient Temperature I C - Collector Current (ma) 14 12 1 8 6 4 2 I F = 1 ma I F = 5 ma I F = 1 ma I F = 2 ma.1.2.3.4 V CE - Collector Emitter Voltage (V) V CEsat - Collector Emitter Voltage (V).4.35.3.25.2.15.1.5. I F = 1 ma I c = 1 ma I c = 2 ma I c = 5 ma -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) Fig. 8 - Collector Current vs. Collector Emitter Voltage Fig. 11 - Collector Emitter Voltage vs. Ambient Temperature Rev. 2.6, 21-Jul-15 5 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 N CTR - Normalized CTR (NS) 1.4 1.2 1..8.6.4.2 T amb = -55 C T amb = 25 C T amb = C T amb = 75 C T amb = 1 C Normalized to: I F = 5 ma, V CE = 5 V, T amb = 25 C.1 1 1 1 I F - Forward Current (ma) F CTR (khz) 1 V CC = 5 V 1 1 1.1 1 1 1 I C (ma) Fig. 12 - Normalized CTR (non-saturated) vs. Forward Current Fig. 15 - F CTR vs. Collector Current N CTR - Normalized CTR (sat) 1.2 1..8.6.4.2 V CE =.4 V Normalized to: I F = 5 ma, V CE = 5 V, T amb = 25 C T amb = C T amb = -55 C T amb = 25 C T amb = 75 C T amb = 1 C.1 1 1 1 I F - Forward Current (ma) t on, t off Switching Time (μs) 1 1 1 1.1 V CE = 5 V, I C = 2 ma t off (μs) t on (μs) 5 1 15 2 R L - Load Resistance (kω) Fig. 13 - Normalized CTR (saturated) vs. Forward Current Fig. 16 - Switching Time vs. Load Resistance -2-4 V CE = 5 V R L = 1 Ω Phase Angle (deg) -6-8 -1-12 -14-16 R L = 1 Ω 1 1 1 1 f - Frequency (khz) Fig. 14 - F CTR vs. Phase Angle Rev. 2.6, 21-Jul-15 6 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 PACKAGE DIMENSIONS in millimeters 4 3 4.4 typ..2 ±.5 Pin One I.D. 1 2.6 +.2 -.3 7. ±.3 Lead coplanarity.1 max. 2.85 max. 2.6 ±.2 2. ±.1 Possible footprint 1.27.9.4 ±.1 1.27 nom..1 ±.1 5. 7.6 Rev. 2.6, 21-Jul-15 7 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 PACKAGE MARKING MT16 V YWW 68 TCMT46 V YWW 68 PACKAGING INFORMATION (TAPE AND REEL) in millimeters Top cover tape 17998 Embossed carrier Embossment Fig. 17 - Tape and Reel Shipping Medium.3 ±.5 2 ±.1 4 ±.1 1.55 ±.5 Pin 1 1.75 ±.1 7.5 ±.1 4.4 7.4 ±.1 7.4 ±.1 16 ±.3 5 2.2 ±.1 2.6 ±.1 8 ±.1 2.95 ±.1 1.6 ±.1 Fig. 18 - Tape and Reel Packing (3 parts per reel) Rev. 2.6, 21-Jul-15 8 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT16, TCMT46, TCMT466 1.75 Ø 1.55 2 4 2.6.3 technical drawings according to DIN specification 7.5 1.6 16 5 7.4 12 Ø 1.6 2.2 Direction of pulling out 18427 Fig. 19 - TTape and Reel Packing for TCMT46X (2 parts per reel) 1.75 Ø 1.55 2 4 2.6.3 technical drawings according to DIN specification 7.5 1.6 16 5 7.4 12 Ø 1.6 2.2 Direction of pulling out Fig. 2 - TTape and Reel Packing for TCMT46XT (2 parts per reel) 18427_1 SOLDER PROFILES Temperature ( C) 3 25 2 15 1 255 C 24 C 217 C max. 12 s max. 26 C 245 C max. 3 s max. 1 s max. ramp down 6 C/s HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Floor life: unlimited Conditions: T amb < 3 C, RH < 85 % Moisture sensitivity level 1, according to J-STD-2 5 max. ramp up 3 C/s 5 1 15 2 25 3 19841 Time (s) Fig. 21 - Lead (Pb)-free Reflow Solder Profile According to J-STD-2 for SMD Devices Rev. 2.6, 21-Jul-15 9 Document Number: 83512 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Revision: 13-Jun-16 1 Document Number: 91