5.2 General Specifications Door Construction: 5 Piece Wood Mortise & Tenon door. Center Panel Construction: 3/8 thick veneer center panel. See drawings for other available options. Rail/Stile Size Options: Default/Prime Rail & Stile is 2 3/W. Minimum Rail is 2 1/W with Concealed Hinges. Minimum Rail /Stile is 1 1/W without hinges. Maximum Rail/Stile is 4 1/W, but this becomes a function of cabinet width. Frameless Drawer fronts: Minimum Stile width is W for proper drawer box attachment. Inset Frame Drawer fronts: Minimum Stile width is 1 1/W for proper drawer box attachment. Minimum HINGED Door Size: Based on Prime Rail/Stile Width and Prime Panel: 7 W x 7 H. We often get the question: Your drawer fronts are 5 7/8 H, why isn t the minimum door width 5 7/8 W?. If we were to use a drawer front turned to become a door, the rails and stiles would be reversed and beside a standard door, this would look odd, especially with a stained finish. Hinged doors smaller than the listed minimum width will be manufactured with slab doors. Minimum PULL OUT Door Size: Based on W Stiles and a Prime Panel: 5 1/W x 5 1/H. As the width of the door decreases, the stiles will remain full size until the center panel reaches 1 1/W, at that point the stile width will decrease until it reaches the minimum of. Maximum Door Size: 2W x 48 H Wider/Taller doors will have intermediate cross rail and multiple panels. Cross Rails can be removed, however this voids the warranty. Radius Doors Available: No. 3 Dimensional Mitered Doors Available: Wainscot/Appliance Panel Types: Standard rails & panels. Dimensioned drawing showing the number of panels and location of cross rails is required. Maximum size: 9W x 48 H. Wainscot Arch & Arched Top Door Availability: Recessed Filler/Pilaster Availability: 3/8 Veneer Panel Prime Center Panel Roxborough Panel Edge Type Availability 1/ Veneer Panel Solid Reverse Panel Additional Flat Panel Options Available Raised Panel Options To determine Minimum Door Width Dimension use this Formula: (Rail Width x 2) + (Panel Raise Dimension x 2) + 0.625 54 Panel Effingham Panel Imperial Panel Baron Panel Essex Panel Malibu Panel Savannah Panel 2 1 4 " Camden Panel Geneva Panel Princeton Panel
Drawer Front Options Standard Door Match Drawer Front Specifications Recessed Veneer Door Match (Most Common) Vertical stiles will be full size. See chart for top & bottom rail sizes as well as space for hardware, according to drawer front height. DH French Country Drawer Front: Available for top drawers in Full Access Frameless lines only. 1 1/ Thick. 5 7 8 " Drawer Front Ordering Methodology: As the drawer front height increases beyond the default top drawer height (which is different for each cabinet line), the drawer rails will increase in size until the full rail width is attained. The center panel will remain the same until the rails have reached full width. At this point the center panel will begin to increase along with the drawer height. The information below is based on the prime door rail width of 2 3/. The dimensions shown WILL change if a rail size other than 2 3/ is selected. The following information is also representative of the prime configuration of rails, stiles and center panel as shown on the left side of this page. Full Access Frameless DH 5 7 8 " 5.2 Recessed Veneer Door Match with Designed for Inset Frame Cabinets ONLY. Tuscan Arched Drawer Front: Available for top drawers in Full Access Frameless lines only. 1 1/ Thick. Top Drawer Less than 5.87H Slab Only DH - (2 x outside edge profile) Top Drawer (Recessed) 5.87H W 1.87H Lower Drawer (Recessed) H - 7.2H ( DH - 1.875 ) / 2 1.87H Lower Drawer (Recessed) 7.37H + W DH - 5.5 Solid Flat Slab Drawer Front 1 3 4 " Inset Frame Top Drawer Less than 5.437H Slab Only DH - (2 x outside edge profile) Top Drawer (Recessed) 5.437H W 1.437H 5/4 Raised Slab Drawer Front 1 1 8 " Lower Drawer (Recessed) 5.562H - 6.812H ( DH - 1.4375 ) / 2 1.437H Lower Drawer (Recessed) 6.937H + W DH - 5.5 Full Overlay Frame 3/8 Slab with Applied EK115 Moulding Recommended for Inset Frame only. Top Drawer Less than 6.H Slab Only DH - (2 x outside edge profile) Top Drawer (Recessed) 6.H W H Lower Drawer (Recessed) 6.62H - 7.87H ( DH - 2.5 ) / 2 H 1/ Slab with Applied Alexandria Moulding (M111) Recommended for Inset Frame only. Lower Drawer (Recessed) 8 H + W DH - 5.5 DH = Drawer Height The minimum flat space (for hardware) that we allow on a drawer front is 5/8. The default top drawer height is a cabinet line dependent value that we base all other drawer fronts on.
Availability Profile: Most mullion styles have suggested ratios for width and height in order to maintain proper proportions for the design. Please refer to the mullion door specifications for these suggested sizes. 12Lite (Wide Rail) 12Lite 10Lite 9Lite 8Lite (Wide Rail) 8Lite 6Lite 2P4Lite 2P1Lite 2Lite 1Lite 4Lite 5.2 2P3LiteAC-4 4LiteAC-4 Quarter Arch C Harmony Glass 3Lite Porthole 9Lite Porthole 2P Porthole 2P9Lite Porthole Symphony 2P Symphony 7 Lite Symphony 10 Lite Symphony 13 Lite Symphony 2Lite 2P2Lite 2P4Lite Unitas 7Lite Helix 10Lite Gothic Arch 11Lite Ellipse 12Lite Gothic DBLARCH
Availability Profile: Most mullion styles have suggested ratios for width and height in order to maintain proper proportions for the design. Please refer to the mullion door specifications for these suggested sizes. 8Lite X 2 Panel 4 Lite X 2 Panel 4 Lite X 4Lite X 4Lite X 16Lite Hourglass 12Lite Hourglass 6Lite Hourglass 12Lite Rosedale 8Lite Rosedale 4Lite Rosedale 5.2 16Lite X 16Lite X 12Lite X 12Lite X 8Lite X
5.2 Finish The standard finish for the back of all doors and drawer fronts is base stain without shader or glaze or base paint without glaze. An additional charge will apply to finish the backs of the doors and drawers exactly like the fronts. Elmwood highly recommends using the 1/16 Radius edge in place of Square edge when a painted finish is required, as this edge will minimize edge chipping. Painted wood doors will develop hairline fractures at joints on rails and stiles as well as rails and center panels. THIS IS NOT A WARRANTY ISSUE. 5 Piece MDF doors will telegraph the joint location between the stile and rail. There will be open gaps at the joint between the panel and the rail. As a result, surface hairline fractures may develop at the joints. THIS IS NOT A WARRANTY ISSUE. Veneer center panels will absorb stain differently than solid rails and stiles which may affect the overall appearance of the finished door. Natural finishes also contain this characteristic. Glazed finishes appear different on different doors styles, different outside edge profiles as well as on different wood species. It is required that a sample door is viewed before the cabinetry order is placed. Door Style Factors for Available Species All door style factors listed below are based on the Prime Rail/Stile Width and Center Panel Configuration for this door style as shown on the left side of this page. Any changes to the prime door style, included rail/stile width changes, panel changes, etc. will result in changes to the door style factor (DSF) and price point (P.P.). Species DSF 20/20 Species DSF 20/20 Alder - Clear 1.70 11 Oak - Quarter Cut White (Solid Reverse) 1.77 12 Alder - Knotty (Solid Reverse) 1.63 10 Oak - Rift Cut Red 1.70 11 Aqua Gloss N/A N/A Oak - Rift Cut White 1.84 13 Ash - Quarter Cut White N/A N/A Oak - Textured Quarter Cut White N/A N/A Bamboo (Caramel, Natural Light) N/A N/A Oak - Textured Rift Cut Red N/A N/A Cherry - Flat Cut 1.70 11 Oak - Textured Rift Cut White N/A N/A Cherry - Knotty N/A N/A Paint Grade 1.56 9 Cherry - Quarter Cut N/A N/A PET (High Gloss, Ultra Matte) N/A N/A Cypress - Select Grade N/A N/A Pine (Clear, Knotty) N/A N/A European Steamed Beech (Flat Cut, Quarter Cut) N/A N/A Quarter Cut Black Limba N/A N/A Hickory - Flat Cut N/A N/A Red Birch N/A N/A High Pressure Laminate N/A N/A Sapele - Ribbon Cut N/A N/A Mahogany (Khaya) 1.77 12 Stainless Steel N/A N/A Maple - Flat Cut 1.63 10 Teak (Flat Cut, Quarter Cut) N/A N/A Maple - Quarter Cut N/A N/A Tineo N/A N/A MDF - 1 Piece N/A N/A Veneer - Textured Faux Wood N/A N/A MDF - 5 Piece 1.56 9 Vision Series Veneers N/A N/A Melamine N/A N/A Vista Series Veneers N/A N/A Oak - Flat Cut Red 1.63 10 Walnut 1.91 14 Oak - Flat Cut White (Solid Reverse) Walnut - Quarter Cut N/A N/A Oak - Quarter Cut Red N/A N/A Legend: N/A - Species not available for this door style. - Species is available (by request). Pricing not yet established.