Version 00 WILKINSON HUTES ANADA PAGE OF This section is based on a system produced by: Part GENERAL RELATED DOUMENTS - GARAGE HUTE Wilkinson hutes anada Toronto, Ontario, ANADA -- A The general provisions of the contract, including General and Supplementary onditions and Division, General Requirements, apply to the work specified in this section DESRIPTION OF WORK A Work Included: Furnish and install where shown on plans inch (00 mm) diameter trash chute as manufactured by Wilkinson hutes anada as specified below SUMITTALS A atalog uts: efore the trash chute is delivered to the job site, submit catalog cuts to the Architect in accordance with these specifications, showing all details of installation and assembly and all requirements for work by other trades Product Data: Manufacturer s product specifications, standard details and recommendations for project conditions; indicate selected sizes and installation details specific to the project Shop Drawings: : Plans: Scale mm to 00 mm; indicate locations, dimensions, and required associated construction activities : Elevations/Sections: Scale mm to 00 mm; indicate locations, dimensions, and required associated required construction activities : Details: Scale mm to 00 mm; indicate: a Shop drawings specific to project conditions b Interface with adjacent construction c Dimensions and tolerances d Products required for installation of the trash chute, but not supplied by the equipment manufacturer WILKINSON HUTES ANADA Telephone: -- / Fax: --
Version 00 WILKINSON HUTES ANADA PAGE OF D Quality Assurance/ontrol Submittals: ontractor s ertification that: a) Products of this section are manufactured by Wilkinson hutes anada, as distributed by Wilkinson hutes anada b) Manufacturer s certification that installer of manufacturer s product is approved c) Applicable standards: National Fire Protection Association (NFPA/8), and the Ontario uilding ode standards as referenced herein E lose-out Submittals: Operation and Maintenance Data: a) Manufacturer s printed Operation Manual Warranty Documents: Issued and executed by the manufacturer and installer of the system QUALITY ASSURANE A Qualifications: Manufacturer: Minimum five () years-documented experience producing products specified in this section Installer: Approved by the Manufacturer, and having a minimum of five () years experience Pre-Installation Meetings: onvene at job site a minimum of seven () calendar days prior to scheduled beginning of construction activities of this section to review requirements of this section Require attendance by representatives of the following: a Trash chutes manufacturer or designated representative b Installer of this section c Other entities directly affecting, or affected by, construction activities of this section d Notify Architect four () calendar days in advance of scheduled meeting date RELATED WORK Y OTHERS SPEIFIED ELSEWHERE A The following work is excluded from the scope of work in this section and is included in other divisions of the specifications for inclusion in the scope of work of others WARRANTY Flashing at the roof Water supply and valves to flushing and fire sprinkler heads Installation of the plumbing access door provided under this section is to be by the forces erecting the shaft enclosure walls A Manufacturer s warranty: Furnish manufacturer s standard one () year warranty from date of temporary certificate of occupancy or similar, locally mandated permission to use the project common areas for their intended use Warranty shall apply to defects in product workmanship and materials WILKINSON HUTES ANADA Telephone: -- / Fax: --
Version 00 WILKINSON HUTES ANADA PAGE OF Part PRODUTS MANUFATURERS A Acceptable manufacturers: WILKINSON HUTES ANADA as distributed by Wilkinson chutes anada, Toronto, Ontario, ANADA Telephone: -- Substitutions: Not permitted omponents: The chute shall be inch (00 mm) diameter of US # gauge ( mm) aluminized steel as manufactured by Wilkinson hutes anada Intake Doors: Stainless steel, inches wide x 8 inches high (80 mm x 0 mm), bottom hinged, hand operated self-closing positive latching doors bearing ½ hour, c U L (Underwriters Laboratories Label) designation, and rated for a 0 F ( ) maximum door temperature rise over 0 minutes, with stainless steel trim in a c U L approved, Label, ½ hour assembly Discharge: Wilkinson hutes anada type A open end chute discharge door with F ( ) fusible link at the bottom of the chute discharge to close automatically when the ambient temperature reaches F ( ) as required by city or provincial building and/or fire codes Unit with c UL rating as described above Vent: hute shall extend full diameter through roof to metal top vent cap 0 inches (0 mm) above roof level with counter flashing and insect screen A roof curb [ ( mm) x ( mm) x minimum of 8 high (0 mm)] is required for flat roof conditions and is to be provided by others Specify stainless steel for aggressive environments Accessories: / inch (9 mm) IPS flushing spray head and / inch ( mm) sprinkler head above highest intake Additional / inch ( mm) sprinkler heads at every second intake (counting from the top) or as required by local code Provide Disinfecting & Sanitizing unit for installation in line to the flushing spray head onnection to flushing spray head, back flow prevention valve and electric control switch by others Provide inches (8 mm) wide x inches (8 mm) high right sidehinged, hand operated, self closing, positive latching, c UL /-hour labeled, stainless steel plumbing access door having stainless steel door trim for installation by forces erecting enclosing shaft wall Door for access to disinfecting & sanitizing unit above the highest intake door of the chute 8 Offsets (bends) in the chute, if required, shall be made the same diameter as the chute of # US gauge ( mm) aluminized steel and have an additional layer of # US gauge ( mm) aluminized steel reinforcing the impact area Offsets are not to deviate more than 0 o off the vertical axis of the chute 9 Provide rubberized sound coat vibration dampening compound to the exterior of the chute only Include sound isolator pads at each floor support frame WILKINSON HUTES ANADA Telephone: -- / Fax: --
Version 00 WILKINSON HUTES ANADA PAGE OF FARIATION 0 Sprinkler System: hute shall be protected internally by automatic sprinklers This requires a sprinkler at or above the top intake door of the chute, and in addition, a sprinkler shall be installed within the chute at alternate floor levels in building over two stories in height with mandatory sprinkler located at the lowest service level A The trash chute shall be fully factory assembled and all joints, except those required to separate the sections for shipment and installation shall be welded or lockseamed tight The floor intake doors shall be bolted in place on throats formed into the chute All chute sections shall flash inside the sections below and there shall be no bolts, clips, or other projections inside the chute to snag the flow of material Prepositioned support frames shall assure proper intake levels and there shall be an expansion joint in the chute between all support joints Discharge hoppers and offsets, where required, shall be reinforced and separately supported in the impact area Part EXEUTION EXAMINATION A Verification of conditions: Area in which system is to be located is correct size and location, and is prepared for installation of trash chute and components Installer s examination: Have installer of this section examine conditions under which construction activities of this section are to be performed, then submit written notification if conditions under which construction activities of this section are to be performed are unacceptable eginning construction activities of this section before unacceptable conditions have been corrected is prohibited General ontractor shall verify and record chute alignment with installer immediately following installation INSTALLATION A Install trash chute in accordance with shop drawings and manufacturer s printed installation instructions DEMONSTRATION A Arrange demonstration of system operation, conducted by manufacturer s representative, to Owner s maintenance personnel * END OF * WILKINSON HUTES ANADA Telephone: -- / Fax: --
NOTES: TYPIAL INTAKE PLAN 8mm ALL HUTES TO HAVE WELDED VERTIAL LOK SEAMS AND INSIDE LAP ROUNDAOUT JOINTS PARTITIONS AROUND HUTES NOT TO E PLAED UNTIL AFTER HUTE INSTALLATION, UTTING OF S OR HUTES SHALL E PERFORMED Y OTHERS MISELLANEOUS STEEL TO HAVE SHOP OAT OF PROTETIVE ENAMEL ONTRATORS TO VERIFY AND APPROVE ALL DIMENSIONS ON THESE DRAWING WITH ONDITIONS ON THE JO SITE WILKINSON HUTES ANADA WILL NOT E RESPONSILE FOR DEVIATIONS FROM THE DRAWING ONE APPROVED IF FRAMES ARE TO SIT ON SU S, PLEASE PROVIDE INFORMATION REGARDING THIKNESS OF FINISHED THE FINAL RESPONSIILITY FOR ENSURING THAT DOORS ARE SITTING FLUSH TO WALLS, MUST LIE ON TRADES ONSTRUTING THESE WALLS, DUE TO MOVEMENT WHIH MAY OUR AFTER INSTALLATION THIS DRAWING IS THE PROPERTY OF WILKINSON HUTES ANADA AND IS LOANED ON THE ONDITION THAT IT IS NOT TO E REPRODUED AND IS NOT TO E USED IN WHOLE OR PART TO FURNISH INFORMATION FOR THE MAKING OF DRAWING LINTEL, IF REQUIRED AOVE DOOR, Y OTHERS ROOF HUTE RISER TO E 00mm DIA FARIATE WITH ga ALUMINZED / SATIN OTE STEEL 00 Ø mm SLA OPENING REQUIRED A ROOF 000 VENT RISER 8 9 8 9 8 HEIGHTS TO E DETERMINED HEIGHTS TO E DETERMINED TYPIAL INTAKE DOOR WILKINSON TYPE DOOR W 80mm WIDE x 0 mm HIGH OTTOM HINGED NOISELESS, SELF-LOSING, SELF-LATHING STAINLESS STEEL, TOP HINGED INSWINGING AFFLES EARING A ANADIAN UNDERWRITER'S LAORITORIES -/ HR, TEMPERATURE RISE 0F 0 MIN LAEL EMOSSED " RUISH" TRIM SET DISHARGE TYPE "A" HORIZONTAL AORDIAN, SPRING LOADED HELD OPEN ON A FUSILE LINK ASSEMLY ASSEMLY EARS -/ HOUR UL FIRE RATING FLUSHING SPRAY HEAD WITH ONNETION Y OTHERS 9mm ONNETOR READY FOR TYPIAL HUTE SUPPORT Y MEANS OF LIPS WELDED AT QUARTERS TO SIT ON ANGLE IRON AND AR GRID TYPE FRAME STEEL TO mm THIK MINIMUM F UL SPRINKLERS TO E INSTALLED AT TOP INTAKE AND ALTERNATE INTAKES ELOW AND READY FOR ONNETION Y OTHERS SPRINKLERS ARE ON: VENT TO EXTEND FULL DIAMETER THRU ROOF TO A HEIGHT OF 000 mm VENT TO E OVERED WITH A HINGED RAINAP WITH mm AIR SPAE AND HOLDOWN LIPS ROOF EXTENSION TO E ALUMINZED/SATIN OTE STEEL FINISH AND VENT SHALL E ALUMINZED/SATIN OTE STEEL DUT 9 8 A 0 HEIGHTS TO E DETERMINED DETAIL OF ROUNDAOUT JOINTS " " A " 89 HEIGHTS TO E DETERIMED 'A' EXPANSION st TRANSMITTAL RESUMITTAL APPROVED FOR FARITION JO NAME: '' EADED '' WELDED DISHARGE LOATION: REPRESENTATIVE: WILKINSON HUTES ANADA ITEM: ONE RUISH HUTE - WRA0 FILE # PO # JO #