FORZA 700 SPEED Supplemental manual

The FORZA 700 has evolved into a Speed Monster. The finely honed form minimizes air resistance, and the forward tilting rotor head helps transform all available power into speed. Fly beyond limits with the FORZA 700 SPEED. No.88370 FORZA 700 SPEED Supplemental manual PLEASE READ THIS FIRST All new streamlined body Newly-designed landing gear to greatly reduce air resistance Blended front and rear fairings for smooth airflow Large canopy ensures visibility at high speed Super strong machined main drive gear and tail drive gear All new large diameter aluminum hub supports oversize main gear for long life and efficient power transmission FORZA 700 SPEED Specifications Length Height Width Main rotor dia. Tail rotor dia. Gross weight Gear ratio Main shaft dia. Tail output shaft dia. Control system Tail drive system 1,399 mm 338 mm 165 mm 1,619 mm 262 mm 4,000 g ~ (not including battery) 8.62 1 4.72 12 mm 6 mm 120 CCPM Shaft drive

INTRODUCTION Thank you for purchasing this JR product. In addition to this manual, please also refer to the FORZA 700 (standard) manual during assembly of this product. This manual describes changes from the FORZA 700. For each step, please read this manual first, then refer to the FORZA 700 manual. There are also changes to the radio setup - please refer to this manual first. Removed and added parts list The table below describes part changes for each assembly step. Removed parts from FORZA 700 Qty. Assembly procedure Added parts for FORZA 700 SPEED Qty. Pinion gear T11 1 1-5 Pinion gear T13 1 Bevel gear B T22 1 Metal front bevel gear T22 assembly 1 Tail pinion shaft 1 Poly slider 6 x 9.5 x 0.13 1 1-6 Bevel gear pin Φ2.3 1 Setscrew M3 x 6 1 Body catch L21 2 2-3 Body catch L23 2 Body catch L21 2 Carbon tray S 1 Landing strut adapter 4 Spacer L12 8 2-4 Socket head bolt M3 x 8 2 Button head bolt M3 x 20 8 Socket head bolt M2.6 x 5 8 Carbon tray S 1 Carbon bottom plate 1 Spacer L12 8 Carbon side plate L/R 1 each Cross member L60 M2.6 2 Landing gear front L/R 1 each Socket head bolt M2.6 x 5 4 Bottom plate bracket 4 Button head bolt M3 x 20 8 2-5 Landing strut adapter 4 Cross member L60 M4 1 Button head bolt M3 x 6 6 Button head bolt M4 x 10 2 Flat head bolt M2.5 x 8 12 Landing strut 2 Landing gear mount 1 Landing skid 2 Landing gear rear 2 Landing skid cap 4 2-6 Socket head bolt M3 x 8 4 Setscrew M4 x 4 4 Nylon lock nut M3 (t2.8) 2 Socket head bolt M3 x 10 4 Button head bolt M3 x 6 6 Main drive gear T112 1 HG main drive gear T112 1 Flat washer M3 5 HG main gear hub 1 Button head bolt M3 x 8 5 HG tail drive gear T104 1 3-1 HG tail gear hub 1 Button head bolt M3 x 6 5 Flat head bolt M2.5 x 6 16 Tail drive gear T104 1 3-2 Servo holding plate 4 Body absorber plate II 4 4-1 Edge protector (50mm) 1 FBL threaded rod L45 2 4-7 Turnbuckle threaded rod L45 2 FRP rear body (Forza 700) 1 5-5 FRP rear body (Forza 700 SPEED) 1 Bevel gear B T22 1 Rear bevel gear T22 assembly 1 Tail output shaft 1 Bevel gear pin Φ2.3 1 5-6 Setscrew M3 x 6 1 Carbon vertical fin 1 5-8 Carbon vertical fin (Forza 700 SPEED) 1 Carbon tail rotor blade 2 5-9 Carbon tail rotor blade XB92 2 Rubber grommet 2 Body clip 1 Snap pin 4mm 2 Body clip plate 1 6-3 FRP front body (Forza 700) 1 Flat head bolt M3 x 10 2 FRP front body (Forza 700 SPEED) 1 P.2

BEFORE COMMENCING ASSEMBLY Standard FORZA 700 assembly manual - Page 2 to Page 7 - These steps are very important for assembling the FORZA 700 SPEED. Please carefully read and understand each step before commencing assembly. SPEED MONSTER Standard FORZA 700 assembly manual - Page 5 Additional items required - The following items are required for the SPEED. Note they are different from the standard FORZA 700. Motor : 12S / KV500~560 ESC: greater than 160A Battery : 12S 4500mAh~5000mAh * If your motor has an 8mm motor shaft, JR No.62029 (pinion gear T13 for 8mm motor shaft) is required. Main rotor blade : 700mm~720mm * Recommended main rotor blades : JR No. 83136 (carbon main rotor blade XB720-F3C) ASSEMBLY Assembly procedure 1-1 to 1-4 Assembly procedure 1-5 Pinion gear T11 has been changed to a pinion gear T13. Assembly procedure 1-6 Bevel gear B T22 has been changed to the metal front bevel gear T22 assembly. Please refer to the figure below. * Use the supplied poly slider 6 x 9.5 x 0.13 as necessary to eliminate any up-down movement when the metal front bevel gear T22 assembly is installed. * Once the tail pinion unit is completed, check for smooth rotation of the bevel gear. If it does not rotate smoothly, then loose the setscrew M4 x 4 securing the tail pinion gear and while expanding gap 'A' in the figure (between the metal front bevel gear T22 assembly and the tail pinion gear), secure the setscrew M4 x 4 again. Adjust until you get appropriate backlash. * Apply silicon grease evenly over the bevel gear. Tail pinion unit R Tail pinion unit bearing block assembly Bevel gear A T22 Nylon lock nut M2.6 (x 2) Cross member L32 (x 4) Tail pinion unit L Socket head bolt M2.6 x 8 (x 2) Poly slider 6 x 9.5 x 0.13 * Use as necessary Metal front bevel gear T22 assembly Tail pinion gear T22 A ( X2 ) Setscrew M4 x 4 (x 2) Shielded bearing 6 x 13 x 5 (x 2) Tail pinion gear T22 Setscrew M4 x 4 P.3

Assembly procedure 2-1 to 2-2 Assembly procedure 2-3 Body catch L21 has been changed to a body catch L23. Assembly procedure 2-4 Referring to the figure below install the carbon lower frame and the carbon tray S to the upper frame that has been previously assembled. * Sand the surface of the carbon tray S where it is inserted into the slot of the lower frame and use some CA glue to secure. * Check if left and right lower frames are correctly installed (parallel) and then firmly tighten the bolts. CAG Carbon tray S CAG Spacer L12 (x 8) ( X8 ) Carbon lower frame (x 2) Button head bolt M3 x 20 (x 8) P.4

Assembly procedure 2-5 First, refer to the upper figure and install the landing gear front, side plate, landing strut adapter and the cross member L60M4 to the frame. Note that the landing gear front and the carbon side plate have a left and right. Install so the countersunk holes are to the outside. Next, refer to the bottom figure and install the carbon bottom plate and the bottom plate bracket. Carefully note the orientation for the carbon bottom plate. * Before applying thread lock to the bolts and tightening them firmly, be sure all the parts shown in both figures are correctly installed. Carbon side plate R Cross member L60 M4 Landing gear front R ( X2 ) Button head bolt M4 x 10 (x 2) Carbon side plate L ( X4 ) Flat head bolt M2.5 x 8 (x 4) Landing strut adapter (x 4) Landing gear front L ( X4 ) Flat head bolt M2.5 x 8 (x 4) ( X4 ) Flat head bolt M2.5 x 8 (x 4) Bottom plate bracket (x 4) Carbon bottom plate ( X6 ) Button head bolt M3 x 6 (x 6) P.5

Assembly procedure 2-6 Install the landing gear mount. Then install the landing gear rear. Carefully note the orientation for the landing gear rear. Nylon lock nut M3 (t2.8) (x 2) Button head bolt M3 x 6 (x 6) ( X6 ) Landing gear rear (x 2) Landing gear mount ( X2 ) front Socket head bolt M3 x 8 (x 4) * Note the proper orientation P.6

Assembly procedure 3-1 Referring to the figure, assemble the HG main drive gear and the HG tail drive gear. SPEED MONSTER Autorotation sleeve ( X8 ) Flat head bolt M2.5 x 6 (x 8) HG main drive gear T112 Autorotation unit Shim washer 15 x 19 x 0.2 (x 2) * Use these shim washers to eliminate any play between the upper and lower drive gears after the main shaft is installed. * Note the proper orientation HG main gear hub HG tail gear hub ( X5 ) Button head bolt M3 x 6 (x 5) HG tail drive gear T104 ( X8 ) Flat head bolt M2.5 x 6 (x 8) Assembly procedure 3-2 Mount the HG main drive gear and the HG tail drive gear that were previously assembled in assembly procedure 3-1 to the helicopter. * The special socket head bolt M4 x 26 which is used to install the HG tail drive gear can be installed from either direction. P.7

Assembly procedure 4-1 There is no change to the installation method of the swash servos A, B and C. Please refer to the standard FORZA 700 assembly manual 4-1. Glue the edge protectors onto the four body absorber plate II using CA as shown in the figure. Install the servo horns and the joint ball screw then mount each servo to the helicopter. The body absorber plate II are mounted at the same time as the servos are mounted - swash servos B and C are installed with the body absorber plate II. All four body absorber plate II are the same shape. Note the proper installation direction. Edge protector 8mm cut as above 8mm 10mm 10mm Hex tapping screw M2.6 x 12 (x 4) Swash servo B Body absorber plate II (x 4) CAG ( X1 ) ( X2 ) CAG ( X3 ) ( X4 ) ( X5 ) ( X1 ) ( X6 ) ( X2 ) ( X7 ) ( X3 ) ( X8 ) ( X4 ) ( X9 ) ( X5 ) ( X11 ) ( X6 ) ( X12 ) ( X7 ) ( X13 ) ( X8 ) ( X14 ) ( X9 ) ( X15 ) ( X11 ) ( X12 ) ( X13 ) ( X14 ) ( X15 ) for upper side (x 2) for bottom side (x 2) Swash servo A ( X1 ) Body absorber plate II (upper) Swash servo B Swash servo A ( X7 ) ( X8 ) ( X9 ) ( X2 ) ( X3 ) ( X4 ) ( X5 ) ( X6 ) Servo mount plate (x 2) ( X11 ) Swash servo C Servo layout ( X12 ) ( X13 ) ( X14 ) ( X15 ) Socket head bolt M2.6 x 10 (x 8) Swash servo C Body absorber plate II (bottom) Assembly procedure 4-2 to 4-6 P.8

Assembly procedure 4-7 The FBL threaded rod L45 has been changed to a turnbuckle threaded rod L45. It has a reverse thread on one end. Screw on the universal links as shown in the figure, making two sets. For installation, please refer to the standard FORZA 700 assembly manual 4-7. Turnbuckle threaded rod L45 (x 2) SPEED MONSTER FBL universal link (x 4) Toward swash plate 23.5mm Toward rotor head Assembly procedure 5-1 to 5-4 Assembly procedure 5-5 The FRP rear body has been changed to a SPEED body. For installation, please refer to the standard FORZA 700 assembly manual. Assembly procedure 5-6 The tail output shaft and the bevel gear B T22 have been changed to pre-assembled (co-molded) assembly. With this change, some assembly procedures are omitted. For assembly of the tail gear case, please refer to the standard FORZA 700 assembly manual. Bevel gear pin Φ2.3 Tail output shaft collar print 201 Tail output shaft Bevel gear B T22 Changed to Poly slider 6 x 9.5 x 0.13 (x 2) * Use as necessary Setscrew M3 x 6 Rear bevel gear T22 assembly Assembly procedure 5-7 Assembly procedure 5-8 Carbon vertical fin has been changed to a SPEED fin. Button head bolt M3 x 4 Socket head bolt M3 x 8 ( X1 ) ( X2 ) ( X3 ) ( X4 ) ( X13 ) ( X14 ) ( X15 ) ( X5 ) ( X6 ) ( X1 ) ( X2 ) ( X3 ) ( X4 ) ( X5 ) ( X7 ) ( X6 ) ( X7 ) ( X8 ) ( X9 ) ( X8 ) ( X11 ) ( X12 ) Carbon vertical fin (FORZA 700 SPEED) ( X12 ) ( X9 ) ( X11 ) ( X9 ) ( X13 ) ( X14 ) ( X15 ) print 2015/08/31 Button head bolt M3 x 6 (x 2) ( X8 ) ( X7 ) ( X11 ) ( X6 ) ( X5 ) ( X12 ) ( X13 ) ( X4 ) ( X3 ) ( X14 ) ( X1 ) ( X2 ) ( X15 ) P.9

Assembly procedure 5-9 The carbon tail rotor blades (XB105) have been changed to carbon tail rotor blades XB-92. Assembly procedure 6-1 to 6-2 Assembly procedure 6-3 There is a magnet attached at rear of the front body. Open up when installing, and then click the magnets together. The canopy rubber grommets press onto the body catch L23. Then slide the body clip onto the carbon bottom plate. Rubber grommet (x 2) Body clip Body clip plate Flat head bolt M3 x 10 (x 2) FRP front body (FORZA 700 SPEED) 縮尺 1:5 Snap pin 4mm (x 2) Carbon bottom plate Body clip Assembly procedure 6-4 P.10

ADJUSTMENT OTHERS Installation of battery and ESC Refer to the standard FORZA 700 assembly manual page 32 for battery mount and wiring. SPEED MONSTER Gear ratio and rotor RPM setup The gear ratio is different from the standard FORZA 700. With this change, rotor RPM and flight time are also different from the standard FORZA 700 as shown in the table below. This SPEED model does not use a standard gear ratio - it is designed for SPEED. Because of this, the loads on the motor, ESC and battery are large. Flight times will therefore be shorter than anticipated. Keeping these things in mind, please refer to the standard FORZA 700 assembly manual page 33. Gear ratio Motor Battery Pinion Pinion : Main KV value 12 cell T13 8.62 : 1 500~560 Rotor RPM Hovering Stunt SPEED 1,500 ~ 1,600 rpm 2,000~2,100 rpm 2,400~2,500 rpm Servo neutral adjustment Refer to the standard FORZA 700 assembly manual page 38. Setting and adjustment of the transmitter Rotor pitch adjustment and pitch curve recommendations have been changed as follows. In SPEED mode, be careful not to exceed +13 degrees of pitch. Also, as you test fly the model, slowly work toward this pitch value. Sudden application of pitch may over stress the ESC or motor because of high current draw and heat generation. Start with +10 degrees of pitch, and check ESC current draws and temperatures as you gradually increase pitch to +13 degrees. Other than this, please refer to the standard FORZA 700 assembly manual page 39 and page 40. Low pitch Intermediate pitch High pitch Reference pitch -13 0 +13 Hovering -5 +4 +12 Stunt -8 +3 +10 SPEED -5 +10 ~ +13 Pitch curve Stick position Stick position Stick position Hovering Stunt SPEED Main rotor blades To ensure a stability during speed runs, the use of F3C type blades is recommended. Recommended main rotor blade : JR No. 83136 (carbon main rotor blade XB720-F3C) * The use of 3D blades is not recommended - they tend to be unstable during speed runs, causing the model to pitch up. * Do not suddenly apply collective pitch (and be careful during backwards flight) - the supplied tail rotor blades are smaller than standard FORZA 700, and are not designed for sudden pitch applications. Final checks prior to flight, Fine adjustment following test flight, Be sure to read prior to flight Please carefully read the standard FORZA 700 assembly manual page 40 to page 43. P.11

RADIO SETUP INFORMATION For FORZA 700 SPEED, the following setup has been changed from the standard FORZA 700. Other than that, please refer to the standard FORZA 700 radio setup information. Page 3 - Navigating the parameter setup menus 4 - Because the setup range of the collective pitch has changed, the value to input for the SWASH MIX also changes. Change the value from PIT.+45% to PIT. +50%. Page 9 - Servo neutral adjustment 11 - It says "Display [SWASH MIX] on your radio and turn the [PIT.] number to +45%.". This also changes to +50%. Page 10 - DATA SHEET - Input these values for [SWASH MIX], [THRO Curve] and [PITCH Curve]. SWASH TYPE 3Servo 120 AILE + 50% SWASH MIX GAIN ELEV + 50% PIT. + 50% EXP INH ACT EXP L 1 2 3 H Rotor RPM NORM OFF ON IN 0 7 100 OUT 47 60 47 1,500rpm THRO IN 0 0 ST-1 OFF ON Curve OUT 70 70 2,000rpm ST-2 OFF ON IN 0 0 OUT 100 100 2,500rpm NORM OFF ON IN 0 10 90 100 OUT 34 50 86 95 Hovering PITCH IN 0 50 100 ST-1 OFF ON Curve OUT 20 62 91 Stunt ST-2 OFF ON IN 0 100 OUT 30 100 SPEED Place to fly the Forza 700 SPEED Because the flight speed is really fast (much faster than a standard model), the FORZA 700 Speed requires a large flying area. Please be sure to fly in a safe place where there is plenty of open area. P.12

PARTS LIST Only the parts that are changed or added to the FORZA 700 SPEED are describe here. For unchanged parts, please refer to the standard FORZA 700 assembly manual. 62077 70788 62078 62077 62081 80171 80273 62076 80039 80091 80091 80273 62078 62080 62080 62079 80013 Item # Description Qty. Note 62076 Carbon bottom plate 1 62077 Carbon side plate L/R 1 L/R one each, 80273 x 6, 80171 x 2 included 62078 Landing gear front L/R 1 L/R one each, 80273 x 6 included 62079 Landing gear mount 1 62080 Landing gear rear 2 62081 Bottom plate bracket 2 70788 Cross member L60 M4 1 80013 Socket head bolt M3 x 8 10 80039 Nylon lock nut M3 (t2.8) 10 80091 Button head bolt M3 x 6 10 80171 Button head bolt M4 x 10 10 80273 Flat head bolt M2.5 x 8 10 P.13

PARTS LIST 62056 80168 62072 80263 80205 70772 62059 62058 70733 62070 80067 62075 62074 62071 80091 70786 70760 61997 80004 62073 80263 62063 Item # Description Qty. Note 61997 Pinion gear T13 1 80004 x 2 included 62056 Metal front bevel gear T22 assembly 1 80205 x 1 included 62058 Metal bevel gear T22 1 62059 Tail pinion shaft 1 62063 Rear bevel gear T22 assembly 1 62070 HG main drive gear T112 1 62071 HG main gear hub 1 62072 HG main drive gear set 1 80091 x 5, 80263 x 8 included 62073 HG tail drive gear T104 1 62074 HG tail gear hub 1 62075 HG tail gear set 1 80263 x 8 included 70733 Main shaft collar 1 80067 x 2 included 70760 FBL universal link 4 70772 Bevel gear pin Φ 2.3 2 70786 Turnbuckle threaded rod L45 2 70760 x 4 included 80004 Setscrew M4 x 4 10 80067 Setscrew M3 x 3 10 80091 Button head bolt M3 x 6 10 80168 Setscrew M3 x 6 10 80205 Poly slider 6 x 9.5 x 0.13 10 80263 Flat head bolt M2.5 x 6 10 P.14

PARTS LIST SPEED MONSTER 62088 70789 62084 80262 62088 62083 82446 82445 60072 62082 80100 Item # Description Qty. Note 60072 Rubber grommet 4 62082 Body clip set 1 80100 x 2 included 62083 Carbon vertical fin (FORZA 700 SPEED) 1 62084 Carbon tail rotor blade XB92 2 62088 Body absorber plate II 4 Edge protector included 70789 Body catch L23 2 80262 x 2 included 80100 Flat head bolt M3 x 10 5 80262 Snap pin 4mm 10 82445 FRP front body (FORZA 700 SPEED) 1 60072 x 2, 62082 x 1, 80100 x 2 included 82446 FRP rear body (FORZA 700 SPEED) 1 P.15

Oct. 2015 FORZA 700 SPEED Supplemental manual Version 1 The product and the contents of these instructions are subject to change without notice due to improvement.