Optocoupler, Phototransistor Output, Dual hannel Vishay Semiconductors i79073 DESRIPTION The is a two channel optocoupler for high density applications. Each channel consists of an optically coupled pair with a gallium arsenide infrared LED and a silicon NPN phototransistor. Signal information, including a D level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. The is especially designed for driving medium-speed logic, where it may be used to eliminate troublesome ground loop and noise problems. It can also be used to replace relays and transformers in many digital interface applications, as well as analog applications such as RT modulation. A A 2 3 4 8 7 6 5 E E FEATURES urrent transfer ratio, 50 % typical Leakage current,.0 na typical Two isolated channels per package ompliant to RoHS Directive and in accordance to WEEE 2002/96/E AGENY APPROVALS UL577, file no. E52744 system code H, double protection DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5 pending available with option SA 9375 BSI IE 60950; IE 60065 ORDERING INFORMATION M T 6 - X 0 0 # T DIP PART NUMBER PAKAGE OPTION TAPE AND REEL 7.62 mm Option 7 Option 9 AGENY ERTIFIED/PAKAGE TR UL, SA, BSI 20 DIP-8 SMD-8, option 7 -X007T () SMD-8, option 9 -X009T () VDE, UL, SA, BSI 20 DIP-8 -X00 Notes Additional options may be possible, please contact sales office. () Also available in tubes, do not put T on the end. > 0.7 mm > 0. mm Document Number: 83645 For technical questions, contact: optocoupleranswers@vishay.com www.vishay.com Rev..6, 7-May- THE PRODUTS DESRIBED HEREIN AND THIS DOUMENT ARE SUBJET TO SPEIFI DISLAIMERS, SET FORTH AT www.vishay.com/doc?900
Optocoupler, Phototransistor Output, Dual hannel Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T amb = 25, unless otherwise specified) PARAMETER TEST ONDITION SYMBOL VALUE UNIT INPUT Rated forward current, D 60 ma Peak forward current, D.0 μs pulse, 300 pps I FM 3.0 A Power dissipation P diss 0 mw Derate linearly from 25.3 mw/ OUTPUT ollector current I 30 ma ollector emitter breakdown voltage BV EO 30 V Power dissipation P diss 50 mw Derate linearly from 25 2.0 mw/ OUPLER Isolation test voltage V ISO 5300 V RMS Isolation resistance V IO = 500 V, T amb = 25 R IO M 2 V IO = 500 V, T amb = 0 R IO reepage distance 7.0 mm learance distance 7.0 mm Total package dissipation P tot 400 mw Derate linearly from 25 5.33 mw/ Storage temperature T stg - 55 to + 50 Operating temperature T amb - 55 to + 0 Lead soldering time at 260 s Note Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELETRIAL HARATERISTIS (T amb = 25, unless otherwise specified) PARAMETER TEST ONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage I F = 20 ma V F.25.50 V Reverse current V R = 3.0 V I R 0. μa Junction capacitance V F = 0 V j 25 pf OUTPUT ollector emitter breakdown voltage I =.0 μa, I E = μa BV EO 30 65 V Emitter collector breakdown voltage I = A, I E = μa BV EO 7.0 V ollector emitter leakage current V E = V I EO.0 0 na ollector emitter capacitance V E = 0 V E 8.0 pf OUPLER Saturation voltage, collector emitter I = 2.0 ma, I F = 6 ma V Esat 0.40 V apacitance (input to output) f =.0 MHz IO pf apacitance between channels f =.0 MHz 0.4 pf Bandwidth I = 2.0 ma, V = V, R L = 0 50 khz Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Document Number: 83645 For technical questions, contact: optocoupleranswers@vishay.com www.vishay.com Rev..6, 7-May- 2 THE PRODUTS DESRIBED HEREIN AND THIS DOUMENT ARE SUBJET TO SPEIFI DISLAIMERS, SET FORTH AT www.vishay.com/doc?900
Vishay Semiconductors Optocoupler, Phototransistor Output, Dual hannel URRENT TRANSFER RATIO (T amb = 25, unless otherwise specified) PARAMETER TEST ONDITION SYMBOL MIN. TYP. MAX. UNIT D current transfer ratio I F = ma, V E = V TR D 20 50 % SWITHING HARATERISTIS (T amb = 25, unless otherwise specified) PARAMETER TEST ONDITION SYMBOL MIN. TYP. MAX. UNIT Switching times, output transistor I = 2.0 ma, R L = 0, V E = 5 V t on, t off 3.0 μs TYPIAL HARATERISTIS (T amb = 25, unless otherwise specified) V F - Forward Voltage (V).4.3.2..0 0.9 0.8 T amb = - 55 T amb = 25 T amb = 85 NTR - Normalized TR.5.0 V E = V, I F = ma,t A = 25 TR E(sat) V E = 0.4 V T A = 50 NTR iilct6_0 0.7 0. 0 I F - Forward urrent (ma) iilct6_03 0. 0 Fig. - Forward Voltage vs. Forward urrent Fig. 3 - Normalized Non-Saturated and Saturated TR vs. LED urrent NTR - Normalized TR.5.0 0. iilct6_02 V E = V,I F = ma T amb = 25 TR E(sat) V E = 0.4 V NTR 0 NTR - Normalized TR iilct6_04.5.0 0. V E = V, I F = ma T amb = 25 TR E(sat) V E = 0.4 V T amb = 70 NTR 0 Fig. 2 - Normalized Non-Saturated and Saturated TR vs. LED urrent Fig. 4 - Normalized Non-Saturated and Saturated TR vs. LED urrent www.vishay.com For technical questions, contact: optocoupleranswers@vishay.com Document Number: 83645 3 Rev..6, 7-May- THE PRODUTS DESRIBED HEREIN AND THIS DOUMENT ARE SUBJET TO SPEIFI DISLAIMERS, SET FORTH AT www.vishay.com/doc?900
Optocoupler, Phototransistor Output, Dual hannel Vishay Semiconductors NTR - Normalized TR.5 V E = V, I F = ma,t amb = 25 TR E(sat) V E = 0.4 V.0 T amb = 85 NTR 0. 0 iilct6_05 t plh - Propagation (µs) 00 0 iilct6_08 0. T amb = 25, I F = ma V = 5 V, V th =.5 V t phl t plh R L - ollector Load Resistor (kω) 2.5 2.0.5.0 0 t phl - Propagation Delay (µs) Fig. 5 - Normalized Non-Saturated and Saturated TR vs. LED urrent Fig. 8 - Propagation Delay vs. ollector Load Resistor 35 I F IE - ollector urrent (ma) 30 25 20 5 5 0 50 25 85 70 V O t PLH t t S PHL 50 % 0 20 30 40 50 60 iilct6_06 iilct6_09 t D t R t F Fig. 6 - ollector Emitter urrent vs. Temperature and LED urrent Fig. 9 - Switching Timing 5 I EO - ollector Emitter (na) 4 3 2 V ce = V Typical 0 - - 2-20 0 20 40 60 80 T amb - Ambient Temperature ( ) iilct6_07 0 iilct6_ I F = ma f = khz, D F = 50 % V = 5 V V O R L = 0 Ω Fig. 7 - ollector Emitter Leakage urrent vs.temperature Fig. - Switching Schematic Document Number: 83645 For technical questions, contact: optocoupleranswers@vishay.com www.vishay.com Rev..6, 7-May- 4 THE PRODUTS DESRIBED HEREIN AND THIS DOUMENT ARE SUBJET TO SPEIFI DISLAIMERS, SET FORTH AT www.vishay.com/doc?900
Vishay Semiconductors Optocoupler, Phototransistor Output, Dual hannel PAKAGE DIMENSIONS in millimeters Pin one ID 4 3 2 6.645 ± 0.65 5 6 7 8 ISO method A 9.77 ± 0.4 0.95 ± 0.9 4 typ. 0.79 7.62 typ. 3.555 ± 0.255.27 ± 5 0.70 ± 0.9 3 to 9 3.045 ± 0.255 6.095 ± 0.255 i78006 Option 7 2.54 typ. Option 9 0.25 ± 5 7.62 typ. 9.53.03 7.62 ref. 0.7 8.4 min. 4.6 4. 0.2 0.249.02 0.30 typ. 5 max..3 max. 0.76 0.76 2.54 R 0.25.78 2.54 R 0.25.78 8450-8.05.52.05.52 PAKAGE MARKING V WWY H 68 Notes Only options and 7 reflected in the package marking The VDE logo is only marked on option parts Tape and reel suffix (T) is not part of the package marking www.vishay.com For technical questions, contact: optocoupleranswers@vishay.com Document Number: 83645 5 Rev..6, 7-May- THE PRODUTS DESRIBED HEREIN AND THIS DOUMENT ARE SUBJET TO SPEIFI DISLAIMERS, SET FORTH AT www.vishay.com/doc?900
www.vishay.com Legal Disclaimer Notice Vishay Disclaimer ALL PRODUT, PRODUT SPEIFIATIONS AND DATA ARE SUBJET TO HANGE WITHOUT NOTIE TO IMPROVE RELIABILITY, FUNTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. ustomers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 207 VISHAY INTERTEHNOLOGY, IN. ALL RIGHTS RESERVED Revision: 08-Feb-7 Document Number: 900