TP00 OWNERS MANUAL INCH THICKNESS PLANER WITH LEGSET For Your Safety: Read all instructions carefully Save this manual for future referenece SP Printed in Taiwan
Parts List for " Thickness Planer Model No. TP00 Figure 0 0 0 0 0 0 0
Parts List for " Thickness Planer Model No. TP00 Figure Always order by Part Number - Not by Number No No 0 0 0 00- - 0 0- - 0- - - 0 0 0 00-0 00- AC0 Scr Hex Soc Butt Hd M x.0-0 Cap Left Scale Length Cover Upper Cap Right Pad Upper Ring Retaining C Worm Gear L.H. Plate Lock Left *Scr Hex Soc Cap M x 0.- Sleeve Plate Lock Right Shaft Transmission Washer. x x Nut Lock M x.0 Support *Washer x x *Scr Soc Set Cup Pt M x 0.- Worm Elevation Handle Knob Snipe *Scr Hex Soc Cap M x 0.- Chute Dust Knob Chute Cover Shroud *ScrPanHdMx0.- *Washer. x x 0. Manifold Air Gasket Rear Gasket Right Gasket Left Cover Worm Gear R.H. Bushing Screw Elevating R.H. *ScrPanHdMx0.- Plate Dust Chute Clamp Cord Spring /Plunger Frame Upper Block Support Lock Cutter Head Spacer Cutter Head Lock *ScrPanHdMx0.- Knife Planer * Standard Hardware Item - May be purchased locally. These replacement parts are available where you purchased your Planer. 0 0 0 0 - - 0-0 - - - 00-0 - 0-0- 0- - 0-0- 0 0- - SP Bar Knife Lock Screw Knife Lock * xmm Collar Knife *Scr Hex Soc Cap M x 0.- Pulley Cutter head Belt Drive Nut Hex M x.0 L.H. Pulley Motor Retainer Bearing Bearing Ball 0ZZ Head Cutter (Includes Collar knife, Retainer Bearing, Bearing Ball and Gear Pinion) Pin Spring x mm *Screw Hex Hd M x 0.- *Nut Hex M x 0. Rod Step Nut Special M x. Indicator Depth Scr Pan Hd M x 0.- Rod Pointer Elevating Spring Coil.XX0. Cover Pointer Scr Pan Cr M x 0.- Housing Pointer Pointer Nut Lockwasher Ext Tooth M Scr Pan Hd TY TT M x 0.- Gear Pinion Gear Box Asm *Scr Hex Soc Cap M x 0.- *Scr Hex Soc Cap M x 0.-0 Spacer x 0 x Sprocket Chain Ring Retaining Ext STW Lockwasher M Scr Hex Soc Hd Lock M Scr Hex Soc Hd Lock Mx0.- Lockwasher M Scr Soc Set Cup Pt M x 0.- Bushing.xx Owners Manual
Parts List for " Thickness Planer Model No. TP00 Figure 0 0 0 SeeFigure 0 0 0
No 0 0-0 0-0 -0 0-0- 0- Ring Retaining Sprocket Chain Spring Coil Left Block Bearing Plate Retainer Left Roller Outfeed Spring Coil Right Plate Retainer Right * Scr Hex Soc Cap M x 0.- Roller Infeed * Washer. x x Worm Gear L.H. Screw Elevating L.H. Rail Guide Plate Wear Table Rear Case Knife (Knives not included) * Washer M x x *ScrewHexHdMx.-0 *ScrPanHdTy TT Mx0.- Plate Stiffener Spring Torsion Plate Side Guard Cover Side Right Hub Handwheel Knob Handwheel * Scr Hex Soc Cap M x 0.- * Lockwasher M Screw Hex Soc.Fl Hd M x.0- No 0 0 0 0-00 0-00- - 0 - - 0-0- Cover Side RH Scale Thickness Spring Coil.x.x0. Ball Steel Block Guard Block Step Knob Step Pin Step Block *NutHexMx.0 *ScrPanHdMx0.- Spring Flat Base Bolt Adjustment Nut Hex Special M x. Pad Base *ScrHexMx.0- Table Front * Nut Hex M x. NutLockMx. Rod Support *ScrPanHdTy TT Mx0.- Cover Side Left Holder Tool Tool Knife * Wrench Hex L mm Wrench Box M & M Cover Tool Box Scr Hex Soc Cap Mx0.- Rod Pivot Parts List for " Thickness Planer Model No. TP00 Figure Always order by Part Number - Not by Number Repair Parts * Standard Hardware Item - May be purchased locally.
Parts List for " Thickness Planer Model No. TP00 Figure 0 Always order by Part Number - Not by Number No. 0 00-0 0 0 - - 0- Cord w/plug Guard Cord *ScrewPanHd M x 0.-0 Housing Switch Gasket Foam Motor (Includes Brushes) Holder Brush Brush Cap Brush *ScrewHexSocSet M x 0.- Label D RIDGID * Lockwasher M * Standard Hardware Item - May be purchased locally. These replacement parts are available where you purchased your Planer. No. 0 0-0 0 0 AC00 00- Lead Ground *ScrewPanHd Ty TT M x 0.- Rod Motor Pivot Switch Reset (Includes Nut) Bezel Switch Switch Locking Switch Screw Special Clamp Cord *Washer.xx *ScrewPanHd M x 0.-0
Parts List for " Thickness Planer Model No. TP00 Figure - Legstand Always order by Part Number - Not by Number No. Stiffener Upper Long Stiffener Upper Short Leg Upper Stiffener Lower Long Stiffener Lower Short Leg Lower Foot * Standard Hardware Item - May be purchased locally No. - - Screw Hex M x.- Nut Hex Flanged M x. Washer M x x. Bolt Cup Sq Neck M x.
Maintenance (continued) WARNING: To reduce the risk of thrown blades and other cutter head parts make sure the knife lock bar containing the seven knife lock screws is positioned as shown in the cutter head side view picture.. Repeat procedures through for the second knife.. Check that all knife lock screws are tight and reinstall the dust chute.. Push the installed knife in firmly. Visually check that the knife edge is parallel to the cutter head slot.. Tighten the seven () knife locking screws. NOTE: Move wrench right to left to tighten.. To rotate the cutter head to the next knife, release the cutter head lock. Hold down on the red lock lever located on the left side and rotate the cutter head.. Release the red lock lever and continue to rotate the cutter head until it locks. This should correctly position the second knife. Accessories KnifeLockScrews Knife Lock Bar Do not use any accessory unless you have received and read complete instructions for its use. Power Tool Universal Legset... AC Dust Collector... AC0 Replacement Knives... AC0 Wiring Diagram Black Switch Motor Lead White Over Load Motor Lead Motor Power Cord Green Grounding Wire