(Expressed Panel Facade System) is a versatile, glass fibre-reinforced, recycled wood fibre and magnesium cement based cladding. The panels are fabricated from a combination of recycled timber materials, mineral fibres and the latest fire retardant chemicals. Conventional woodworking equipment required to cut and shape Multiboard. is a lightweight and exceptionally strong board that provides a solid substrate for many decorative finishes. is up to 50% the weight of traditional compressed cement sheeting and has exceptional fire resistance. Non combustible. Tested to AS 1530.1. is an external cladding system that can be erected quickly and efficiently. There is no need for special top hat sections; instead standard, seasoned, treated pine battens are used. has been designed for use in light commercial, light industrial and residential applications where the main external trade is carpentry and the maximum height from ground level is 6.0m. 1100 2400 2700 3000 8 8.8 23.23kg 26.14kg 29.04kg Tested to the strict requirements of AS2908.2. 30% - 50% lighter than traditional compressed cement sheeting. Fastening is by commonly available straight and angled powered brad nailers. This gives one distinct advantage over other systems. Once installed, there is no extra cost or labour requirement filling screw holes; it s ready for texture coating. comprises of 8mm panels that are installed in a vertical or horizontal layout. The panel sizes can be altered in to smaller sized panels to suit different architectural designs. This is made possible by the batten system lay out being totally independent of the wall frame stud spacing and the ease in which Multiboard can be cut in comparison to other linings on the market. The installation takes a fraction of the time of commercial expressed-edge systems. Labour and time saving installation procedure, without the need of specialist trades or tooling. Jointing of the system can be designed "off stud" which means that the facade design is independent of the wall engineering design requirements. Boards can be easily cut to alternative sizes with standard carpentry tools. This will easily allow for alternative design layouts. Ready for texture coating without the need of filling and sanding of screw holes. A good fit for current Environmental & Sustainability Design (ESD) principles. Contains recycled wood fibre and other recycled materials. No Portland cement - Magnesium Oxide Cement is used, which is an eco-friendly and environmentally stable compound. No harmful substances to humans or environment such as crystalline silica. Up to 50% lighter than traditional compressed cement sheeting. High water resistance. High fire resistance. Ignitability Index Spread of Flame Index Heat Evolved Index Smoke Developed Index 0 0 0 0-1 Range 0-20 Range 0-10 Range 0-10 Range 0-10 Tested to ASTM E 514-03 standard test method for Water Penetration & Leakage through Masonry. Laboratory tested by Termimesh Australia. No harmful crystalline silica or asbestos. No special requirements required when cutting with power tools. Tested as safe. High acoustic performance. 50% recycled bamboo / wood fibre, 40% less embodied energy to produce than fibre cement. must be stored in a dry and covered area. If stored externally, must be stacked flat, and raised off the ground. The panels should be supported on level ground and must be protected from the weather. Care should be taken to avoid damage to the products edges and surfaces. If the product becomes wet, the product must be allowed to dry before fixing. must be coated within 2 months of exposure to the elements.
should be stacked and handled carefully to avoid damage. Boards should be lifted from the pallet by sliding sideways and carried on its long edges. Tape CS-3/25. Board adhesive MB RLA 1018 PU adhesive. When designing with, the following needs to be considered: Panel layout - layout so that the battens are at a maximum of 550mm centres. Control joints - Install double-batten control joint every 6m - refer to details section "Detail 1". Maximum height - is designed for a maximum of 12m from ground level. Insulation / Sarking requirements. Coating systems finish requirements. Maintenance. Galvanised steel angles and flashings with a minimum of 1mm BMT. The 90 x 35mm batten must be fixed on to the top plate, nogging and bottom plate with at least two framing nails at each junction. Strict adherence to the BCA must be followed for the number of noggings for walls greater than 2.4m in height. It is important to ensure that the battens are installed so they are straight in both horizontal and vertical directions over the full length of each wall. Adjust battens as required to achieve this. Apply a single 6mm high bead of Silkaflex Pro along the length of the intermediate battens. For smooth cuts, use a circular saw with a fine toothed blade. Determine panel layout then mark out the centre point of each 90 x 35mm batten on the frame. Batten spacing must be at a maximum of 400mm centres. can also be cut easily using a normal hand saw. The edge of can be planed or smoothed with an electric planer, rasp or file, or conventional papers if sanding is required. Position the batten according to predetermined and marked spacing's and ensure that they are vertical (check this with a spirit level in all planes). Apply recommended to the 90 x 35mm TP batten that will form the expressed channel. Ensure the seal is applied to the centre of the purpose designed seal channel on the 90 x 35mm batten. Also apply two 6mm high beads of MB RLA 1018 PU adhesive along the length of the expressed channel battens on either side of the recommended tape. When drilling holes in use a standard timber drill tip. Do not use hammer action. comprises of Multiboard panels fastened to a simplified sub system that incorporates 90mm x 35mm seasoned battens, horizontal backing strip and Multiboard butyl gasket tape 50mm BFT-3/25. Fastening is by Clad Seal and polyurathane adhesive. Pre-painted horizontal backing strip - 10mm x 0.55mm BMT. Fix the battens on the flat to the frame using appropriate framing nails or screws. Use Stainless Steel (SS) brading nails Plaslode C50/SS or DA2150/SS equivalent. Fasteners must be driven just under the face of the board. It is essential to adjust the fixing gun to ensure that the pins are not over or under driven. Refer to figure below. Nail head must be approximately 1mm below the surface of the
Align the first sheet and begin fixing to the battens at a maximum of 150 mm centres. Use a 150mm centre nailing pattern on all battens. 30mm 150mm 150mm Insert the backing strip behind the top of the board. Beads of adhesive Recommended Seasoned T.P. Batten Backing Strip When installing the next layer of apply a bead of the appropriate sealant to the top of the backing strip and then rest an sheet on the purpose designed 3mm edge of the backing strip. fixing details bottom layer of board Where a horizontal joint is required, fix the bottom row of allowing a 15mm overlap of the recommended. Do not nail the top half of the boards at this point. This will facilitate the insertion of the backing strip to the board. Beads of adhesive Backing strip joint details - the backing strip has been designed to overlap whilst retaining a flush fit behind the board. Position the sheet to ensure that all joints are 10mm wide and then finalise the nailing of the panel. Beads of adhesive Panel Recommended fixing details bottom layer of board 100 30 Backing strip joints must overlap the nearest batten and be sealed with two beads of an appropriate sealant, to ensure a water tight joint. 2 Beads of Continue with this installation process until all sheets are installed. All expressed joints can be filled with a flexible acrylic sealant to ensure water tightness in the system. The sealant can be applied directly on to the expanded recommended. Panels to overlap seal minimum of 15mm Backing Strip overlaps at the nearest top hat by at least 50mm Finished wall must be coated within 2 months of exposure to the elements. Ensure that all edges are completely sealed. Use only reputable texture systems and ensure that the application directions are strictly followed. 15 10 After the backing strip is in position, finalise the nailing of the top half of the lower board. This will draw the sheet and backing strip against the batten, completing the seal. Joint - Class A polyurethane sealant should be installed with strict adherence to manufacturers instructions. Ensure that a bead of at least 8mm in diameter is applied.
Vertical Sheet Joint Detail Double Batten Every 3rd Sheet or 3.3m DETAIL 1 Multiboard 12mm 600mm Max DETAIL 1 Studs 450nom. 600 Max Detail 1 - Construction Joint 1.5mm EPDM Foam Seal Continuous 5mm Sikaflex Bead 90mm Nogging 15 min. Horizontal Sheet Joint Detail Vertical Sheet Joint Detail Recommended Sikaflex Bead Treated @400mm Centres Seasoned Treated Pine Pre-Painted Horizontal Backing Strip 10mm x 0.55BMT Internal Corner Detail Brad Nail Continuous Bead of External Corner Detail Window Head Detail Brad Nail Note: Order of for Expressed Joint Brad Nail Continuous Bead of Seasoned Brad Nail Vapour Barrier Panel Continuous Bead of Window Sill Detail Internal Window Head To Architects Details Window Jamb Detail Slab Edge Detail 1 Continuous Bead of Metal Angle Jamb Window Frame Sill Shown Indicative Window Sub-Sill Continuous Bead of Window Frame Shown Indicative Soffit Detail Panel Seasoned Treated Pine 10 nom. Seasoned Vapour Barrier Internal Wall Lining Internal Window Head To Architects Details Head Continuous Bead of Behind Head - Leave Gap Open Between Sheet & Window Frame Head- Shown Indicative Concrete Slab
Slab Edge Detail 2 Concrete Slab Brick Sill Detail 90mm Nogging Brick on Edge Sill legal rights of any person under the Trade Practices Act or otherwise which cannot be excluded or modified at law. The Warranty is strictly subject to the following conditions:- 1. The product, and any other products including fasteners and jointing systems, applied to or used in conjunction with the product must be used and installed strictly in accordance with the recommended installation methods at the time of installation. 2. Under no circumstances will Multiboard be liable for defects arising from:- (a) A failure to use and/or install the product, or any products, strictly in accordance with the product manual. (b) Defective materials not supplied by Multiboard; or (c) Impact. 3. Multiboard will not be liable for breach of Warranty, and no breach of Warranty claim will be accepted, unless the Claimant makes a written claim and provides proof of purchase within 30 days of the alleged defect becoming apparent. 4. This Warranty is not transferable under any circumstances without the prior written consent of Multiboard. 5. A Claimant's sole remedy for breach of Warranty is (at Multiboard's option) that Multiboard will either replace or repair the defect, supply replacement product, or pay for the cost of replacement or rectification of the affected product. Brickwork is manufactured from woven glass fibre, recycled wood fibres, magnesium cement, and additives which catalyse the cementing action. As manufactured, the product will not release airborne dust, however during drilling and sanding operations, glass fibres and fine dust may be released. When using power saws in a confined space, dust extraction equipment is recommended to control dust levels. If power tools are used externally, wear an approved P1 or P2 dust mask, respirator and safety glasses. No special safety precautions are necessary when handling or working with Multiboard. For further information refer to the Materials Safety Data Sheet, please refer to our website. exres (Multiboard) warrants for a period of ten (10) years ("the warranty period") from the date of purchase that all products ("the product") will be free from defects due to faulty manufacture or materials, and will be resistant to cracking, rotting, fire and damage to the extent set out in Multiboard's published literature current at the time of installation, and strictly subject to the conditions set out below. Nothing in this document shall exclude or modify any 6. Under no circumstances shall Multiboard be liable for any consequential loss, property damage or personal injury, economic loss or loss of profits, arising in Contract or negligence or howsoever arising. Without limiting the foregoing, Multiboard will not be liable for any claims, damages or defects arising from or in any way attributable to poor or defective workmanship, defective materials or poor design or detailing, settlement or structural movement and/or movement of materials to which the product is attached, incorrect design of the structure, in the event of but not limited to earthquakes, cyclones, floods or other severe weather conditions or unusual climatic conditions, normal wear and tear, or growth of any organism on any product surface. 7. The express warranties set out above are in lieu of all other representations, warranties or conditions, express or implied including but not limited to implied warranties or conditions of merchantable quality and fitness for a particular purpose, and those arising by statute or otherwise in law or from a course of dealing or use of trade and which are excluded to the fullest extent permitted by law. Specifications can change without notice.