88 5527 991 Homestead Bar Cabinet IMPRTANT NTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part ist Casual Attire For Today's Home A. Top P1. E. Base. F. Plinth M. Center Shelf Hardware ist Hex Wrench Screw 17 pcs.(+1 extra) Magnet 28 pcs. (+1 extra) Machine Screw Small Hex Wrench Head Cap Bolt 6 pcs. (+1 extra) 17 pcs.(+1 extra) For assembly see instructions in carton 88 5527 992 Tools required for assembly : Phillips screwdriver Wood Screw for Magnet (+1 extra) Wood Screw (long) 16 pcs. (+1 extra) Adjustable Pin 20 pcs.(+1 extra) Pull Handle
Tools required for assembly : Phillips screwdriver 88 5527 992 Homestead Bar Cabinet IMPRTANT NTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part ist Casual Attire For Today's Home B. Side Panel C. Side Panel D1. Middle Panel D2. Middle Panel G. Front Rail H. Back Panel I. Back Panel J. Door K. Door. Shelf N. eg. eg P3. P4. P5. Q. Drawer (Knock-Down Construction, please refer to the last page of these instructions for steps to assemble drawers) Also need the following from carton 88 5527 991 : Part ist in carton 88 5527 991 Top (A) Base (E) Plinth (F) Shelf (M) (P1) () Hardware ist in carton 88 5527 991 Small Hex Wrench Hex Wrench Head Cap Bolt Screw Magnet Wood Screw for Magnet Wood Screw (long) Adjustable Pin Pull Handle Machine Screw for Pull Handle 7 pcs. 18 pcs. 18 pcs. 5 pcs. 29 pcs. 17 pcs. 1
Assembly Instructions 2/6 IMPRTANT You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. Magnet STEP 1 Attach 2X Magnets to Top (A) by using Wood Screws in the pre-drilled holes (see Figure 1). A Figure 1 Insert Screws into the pre-drilled holes of Top (A). STEP 2 Insert Screws into the pre-drilled holes of Side Panel (B) and (C), Middle Panels (D), Base (E) and Plinth (F). Screw B C D1 D2 E F
Assembly Instructions 3/6 G Figure 2 D1 D2 Screw STEP 3 Attach Front Rail (G) in between Middle Panels (D1) and (D2) with s (see Figure 2). E Attach Middle Panel (D1) and (D2) onto Base (E) with s. B F N E C STEP 4 Attach Plinth (F) to the unit with s. Attach Side Panel (B) and (C) to the unit with s. Attach egs () and (N) into the pre-drilled holes of Base (E) and tighten.
Assembly Instructions 4/6 STEP 5 Head Cap Bolt A Slide Back Panels (H) and (I) into place. Place Top (A) onto the unit, using s and Head Cap Bolts. Adjustable Pin I H I Insert Adjustable Pins into side panels and middle panels at the desired level. Place Shelves () into position. P1 P3 P4 P4 P3 STEP 6 Attach s (P3) to s (P1) with Wood Screws (long). P1 Assemble s () with (P4) as shown, then place it into position. Wood Screw (long) STEP 7 Attach (P5) to the unit with Wood Screws (short). P5
Assembly Instructions 5/6 Figure 3 J K Figure 4 STEP 8 Attach Doors (J) and (K) by sliding the door lift hinges into the side panels lift hinges (See figure 3). M Assemble Pull Handles to Doors (J) and (K) with Machine Screws. (See figure 4) Slide Drawer and Wine into position. Note: The adjustable shelf (M) is optional (see Figure 5). Figure 5 STEP 9 Insert 12X Wood Screws from the back of the unit, tighten up all the Wood Screws (short). (See figure 6) Note: Please make sure unit is level before tightening these screws. Figure 6
Assembly Instructions 6/6 Drawer (Q) Q3 Q1 STEP 1 Attach Q1 to Q3 and Q4, using a Phillips screwdriver and long wood screws (4X), tighten halfway. Figure 1 Q2 Q4 Attach Q2 to Q3 and Q4 using long wood screws (4X), tighten halfway. (see Figure 1) STEP 2 MAKE SURE RER IS N THE BACK Slide Q5 into the grooves in Q3 and Q4. Be sure to push Q5 all the way forward so it meets Q1. (see Figure 2) Q3 Q1 Figure 2 Q3 Q5 Q1 Q5 Q2 Q4 Figure 3 Q2 STEP 3 Q4 Insert short wood screws (4X) into the pre-drilled holes in Q5, tighten screws. (see Figure 3) Figure 4 STEP 4 Attach hardware pulls with machine screws. (see Figure 4) Tighten all screws used in drawer assembly. Part ist Q1. Front Part Q2. Back Part Q3. Side Part Q4. Side Part Q5. Base Part